STIHL saw does not start after winter.

No stihl 180 is a spark, Stihl MS 180 floods the candle

Before going to the service center, it will be useful to independently try to eliminate the current fault of flooding the candle on the chainsaw. Of course, this is relevant only in the presence of “straight” hands, since, otherwise, it is likely to increase the cost of repair work.

Poor.quality fuel

The chemical composition of low.octane gasoline includes various alcohol components. It takes more time to complete combustion than when using high.quality fuel, respectively, this becomes the main reason for the failure of the chainsaw candle.

Unfortunately, many citizens naively believe that the fuel with the inclusion of alcohol has a positive effect on the consumption of gasoline and acquire fuel surrogates. In some cases, economy really takes place, however, such fuel negatively affects the chainsaw engine, reducing its service life.

Incorrect launch

As a rule, during the first launch of the chainsaw, inexperienced men miss “cotton” with a closed air damper and continue to pull the starter. Because of this, a large amount of fuel accumulates in the combustion chamber, but there is not enough air. The candle is poured with excess gasoline and there can be no question of any spark.

The clogged filter

Due to the strong pollution of the paper filter of the chainsaw, a sufficient amount of oxygen does not enter the fuel chamber. The fuel mixture does not have time to ignite and gasoline fills the candle. If the filter has already developed its resource (this will be noticeable in its appearance), then it must be replaced. If the new filter is not at hand, but it is still necessary to work, then you can try to blow the filter in the back air flow.

The chainsaws of various manufacturers and model rows differ from each other. To clean or change the filter, it will be useful to initially see the operating manual. Well, or look there if you can’t extract a filter without tips.

Ignition system failure

Perhaps this is one of the most difficult problems that will need to be overcome for the further use of a chainsaw. The causes of the malfunction here can also be several.

The wrong gap

For the most part, the gap on the lighting candle of the chainsaw should be within 0.5. 1.2 millimeters (more accurate data should be reflected in the user guide). In order to check if this is, it is necessary to perform the following actions:

• Using a screwdriver or special keys, the bolts are unscrewed that fix the chainsaw cover.
• Having gained access to the flywheel and the magnetic circuit, the level of gap is checked.
• If it does not correspond to the characteristics declared manufacturers, then with the help of a special laying or improvised means (an ordinary A4 sheet, folded several times) is perfect).

Problem in the ignition coil

To make sure the ignition coil is in good condition, you must be able to use a multimeter. This device allows you to measure the degree of reel resistance. There will be resistance in the good coil. In the burned out. cliff or short circuit.

If the coil is in good condition, then the gap between the coil and the flywheel may be broken. To configure it, you need to perform a number of simple actions:

• Dismantling the saw case and the weakening of the bolts on which the ignition system is recorded. To the coil itself, you need to bring the magnet (magneto) of the flywheel.
• The adjusting plate is inserted between the magneto.flywheel and the coil itself. The gap should be within 0.2 mm.
• After tightening the bolts, the plate for adjustment is obtained.
• It is necessary to completely and several times (2-3 will be enough) scroll the flywheel. While he should not cling to the coil.
• The final stage is the assembly of the chainsaw building.

Carburetor adjustment failure

Often the candle on the chainsaw flies due to the incorrect operation of the carburetor. For greater clarity, we recommend watching this video

If you first set up the carburetor yourself, then pay attention to the following factors:

• The presence of built.in compensators and other automatic control elements makes it impossible to adjust without special equipment. In this regard, you will have to contact a specialized service center.
• In the absence of the proper effect of adjusting the carburetor, the cause of filling the candle will be, there is a freezing of the float or the lack of tightness of the valve.

How to check the operability of the fuel pump

The gap between the ignition coil and the flywheel of the chainsaw

You can’t look inside the ignition unit. And the reason for this is a non.graceful design. In service centers, checking its performance is carried out using a special tool. It will be possible to eliminate problems at home if you replace the block.

But before you run to the store behind the new STIHL gas station unit, you need to make sure that the problem does not lie in the wrong gap between the contacts of the flywheel and the ignition module. The reason for the lack of a spark can become both too much gap and its complete absence. In the latter case, the flywheel will begin to contact with the contacts of the module, as a result of which scratches are formed on it.

• Remove the starter;
• loosen the screws of the ignition module;
• Put a plate cut out of a conventional plastic bottle between the module and the flywheel;
• Tighten the screws.

If all these manipulations led to the appearance of a spark, the stihl chainsaw is ready for further work. Otherwise, you will have to conduct a second inspection. If, as a result of the inspection, the absence of a gap is again revealed, you will have to look for the cause in the crankshaft bearings.

STIHL chainsaw may not start and if there is a spark. In this case, it is necessary to look for problems in the operation of the fuel system. To do this, inspect the candle for wet plaque. Its presence indicates excessive fuel supply. When the fuel mixture begins to literally fill the candle, it cannot ignite it.

• unscrew the candle;
• Turn the stihl chainsaw, draining fuel;
• In the same state, pull the starter handle several times, removing the remaining fuel;
• screw the candle in place;
• set the engine control lever to the hot start position;
• pull the label of the starter.

All these manipulations must be carried out with the ignition turned off, settled as far as possible from open fire.

If the problem was the incorrect launch of a cold engine, its “purge” will help return the StiHL gas station to return. If even after the “purging” the chainsaw of the STIHL 180 is not started, you need to look for a solution to the problem in the carburetor.

First you need to check the condition of the fuel filter. To extract it, you need to unscrew the lid of the fuel tank. Further, aluminum wire with a bent end will come to the rescue. With its help, the fuel hose is removed, at the end of which the filter is located.

The condition of the filter can be checked by blowing into it. If the air does not pass, then the filter requires cleaning or replacing. If the air passes freely, you need to look for a blockage in the fuel hose, disconnecting it from the carburetor. The blockage can be eliminated mechanically or replacing the hose.

If the fuel hose and the filter are clean, and the fuel does not enter the candle, the reason for this can be a malfunction of the air pulse to the fuel pump.

There is a membrane in the pump case, which during the movement ensures the supply of fuel to the carburetor and engine. If the chainsaw of the Stihl MS 180 does not start, there may have been a rupture of the membrane. You can check its integrity if you remove the pump cover. If any defects were found during the examination, the membrane is changed.

Repair of the chainsaw STIHL 180

Question: During the operation of the chainsaw, the Stihl MS 180 C stopped holding idle and stalled. I started it with difficulty, but again stalled on idle.

After that it does not want to start. The next day, after unsuccessful attempts to start, removed and washed the air filter. It did not help, I had to take off the candle. it turned out to be dry, although there were plenty of attempts to start.

Peeled a needle of a sapun (was not scored). Changed the fuel filter (although the old is visually not dirty). The carburetor cleaned and just in case put a new candle. The saw does not start! I twisted the candle again. dry. What to do?

Answer: Remove the muffler. Look at the piston, if it on it longitudinal stripes, then you need to replace.

Question: What is the difference between the leading and chain stars of the chainsaw of the Stihl 180 chain?

Answer: There is no difference between the “leading star” and “chain wheel”, these are different names of the same details.

Question: I bought a STIHL MS 180 motorcycle, I really liked it, but I want to ask you if my saw can saw a thick tree?

Answer: The standard length of the MS 180. 35 cm tire, it is possible to cut the log. 70 cm in diameter, if the logs of this diameter prevail, then you need a chainsaw of greater power.

Additionally: Stihl chainsaw 250 ms: characteristics and reviews

MS 180 will cope, of course, with the task, slowly and correctly cut all the logs of large diameter, but you need to remember that when giving heavy loads to the apparatus not created for this, you (at best) reduce the resource of the chainsaw, that is, you closer to its major overhaul.

Question: Tell me, please, is it possible to use a 45 cm tire on a chain saw STIHL 180?

Answer: You can put a tire of maximum length 40 cm on the MS 180 motopile.

Question: Where is the Sapun in the Stihl MS 180 chainsaw is located?

Answer: The valve of the ventilation system (“saopun”) is “on top” of the gas tank and oil tank, not to see visually, t.to. everything is closed there by the starter case.

Question: On MS 180 in a horizontal position, a gas button sees. What to do?

Answer: Most likely, the lever-treasured mechanism is faulty, when turning the unit, one of the levers or rods “sinks”.

Question: Why is the cylinder heated and when heated stalls the motoropyle of Stihl 180?

Answer: The problem is in the ignition module, there may be no compression (necessary).

Question: We use the Stihl 180 chainsaw with a standard tire, recently learned that people put Carving bus on this model. According to the catalog, you can put a 30 cm tire of this type, but is it possible to install 25 cm or this model cannot?

Answer: Carving has a very small spout radius. It is better to use a chain with this tire with a 1/4 step. And here the problems will begin. These are very rarely circuits in retail, but plus to 180th still a stars for 1/4.

About Stihl 250

The STIHL 250 saw is perfectly balanced and combines such qualities as high power and at the same time slight weight and ease of use. Power allows you to install larger tires on this model, which means to saw thicker trees trunks, which increases performance. Weight affects comfort when working with a tool for a long time. Small dimensions allow you to work with a saw in places limited in area or in dense thickets. It is convenient to clean the fallen tree from branches or cut out small shoots with this saw.

If necessary, Stihl 250 can also cope with more complex tasks, but you should not work with maximum loads for a long time. The resource of this model is still not the same as that of professional saws.

STIHL 250 saw is designed using the most modern developments of German engineers, which we will talk about a little later.

Of course, the power unit of the chainsaw of the Stihl MS 250 cannot be compared in power with the engine of the professional model, but it is also capable of a lot. The difference with household chainsaw is felt as soon as you start making the first cut. If desired, buyers can purchase a richer STIHL 250 set, in which it is additionally equipped with devices increasing the comfort of using a saw.

Elimination of the malfunctions of the starting mechanism

The reason for the failure of the entire tool may be an ineffective starting mechanism or problem in the ignition system. If it turns out that the starting device works as usual, then you need to make sure the candle is in good condition

In order to do this, the candle is turned out of the nest and carefully examined, paying attention to the presence of an extraneous raid on its electrodes

It is worth noting that the presence at the place of formation of a spark of traces of a certain property very eloquently speaks of the sources of the “disease” of the entire trigger system. Such source, in particular, can be a carburetor. So, the complete absence of any signs of fuel on the candle (its complete dryness) most likely indicates the lack of fuel into the combustion chamber due to the complete clogging of the carburetor.

If the gasoline on the candle of the chainsaw is fixed, and the cutting device itself does not work normally, then this indicates an excess of the air fuel mixture. The reason for this condition may be a failure in the adjustments of the carburetor, clogging of its jacklers, as well as the incorrect start of the mechanism. In the case of fixing on a candle characteristic soot, it is possible to talk with sufficient confidence about the incorrect functioning of the carburetor or the use of low.quality gasoline.

With all the above signs reflected on the spark plug, it is necessary to remove the carburetor and check its technical condition. Carburetor, when clogging, should be thoroughly cleaned, then adjust the device according to the technological requirements and replace the gas used in the tank. It should always be remembered that the carburetor is a rather complex node, consisting of many small components, details and tubules

Therefore, its repair should be carried out with particular caution and accuracy

In addition to the restoration of the carburetor, it is necessary to check on the stand and the performance of the spark plug itself and, if necessary, set the correct gap in it. If the candle and its work do not like it at all, it is recommended to replace it with a new candle.

Reserve of goods

The Stihl MS 180 C-BE 14 35 cm chainsaw is an improved version of the STIHL MS 180 saw-it has a system for elapse of ERGOSTART launch and side tension of the chain without using the tool. The tool is suitable for harvesting firewood, the formation of crowns of trees, knots, the construction of wooden structures, sawing trees trunks, as well as the implementation of other simple economic work. STIHL chain chain chainsaw has high cutting abilities, wide functionality and slight weight. High level of ergonomics provides ease of operation regardless of the complexity of the task. The device is equipped with a 14-inch bus (35 cm), which provides the ability to work with trees with a diameter of up to 30 cm.

STIHL MS 180 C-BE gasoline has a modern vibration protection system. The anti.vibrational system is located in the zone of the saw handles, and a significant extent drowns out the vibration transmitting from the engine. The instrument is OOSENT a modern lubricant system that regulates the amount of lubrication. The control button of a cold and hot launch, turning on and turning off the tool is represented by a separate lever. This makes the handling of a safe saw, since the operator’s hand always remains on the handle.

Features and advantages of Stihl MS 180 C-BE 14 35 cm

• Ergostart launching system
• Side clipping chain without using a tool
• Small weight
• Convenience
• Quickstop chain brake
• Safety
• Quick chain tension
• Modern vibration protection system
• Modern lubrication system

Equipment

Quickstop chain brake is a protective mechanism when working with chainsaws. The chain brake is triggered when you press the front stop for the hands and for a few seconds stops the saw chain. With a strongly strong giving, the quickstop chain brake is automatically triggered.

Strong vibration in the zone of handles can lead to chronic circulatory disorders in the hands. Therefore, StiHL has developed a highly effective anti.vibration system (AS). In tools with AC, the vibration of the engine transmitted to the handles is noticeably reduced.

STIHL compensator. the regulatory authority in the carburetor. provides almost constant engine power, exhaust quality and fuel consumption for a long time despite the increasing pollution of the air filter. Cleaning the air filter is required only with a noticeable capacity drop in. It becomes possible to work for a long time without maintenance.

The STIHL EMATIC system consists of EMATIC guide tires, Oilomatic saw and oil pump with adjustable supply. The special design of the tire and chain makes each drop of oil to get exactly where it is required to lubricate. This reduces the oil consumption by 50 %.

The spiral spring between the coil of the starting cable and the crankshaft compensates for peak efforts, now there are almost no shocks on the cable. Result: Stihl Ergostart compared to traditional starting devices reduces half the force, and the start speed is about two.thirds.

Such functions of a machine as cold and hot launch, work and shutdown are controlled by a separate lever. This makes management especially convenient and safe, since the right palm remains on the handle.

The proprietary system of fast tension of the STIHL (b) chain turns the saw chain tension into childhood fun. It is only necessary to loosen the nut of the fastening of the cover of the chain stars, and with the help of the adjusting wheel easily and quickly pull the chain. The tool is not required for this.

Having discovered an error or inaccuracy in the text or description of the product, highlight it and click Shiftenter.

The algorithm for determining the malfunction

The reason for the refusal of the saw or the deterioration of its performance may be:

• a clogged battleship cover;
• Air sucker with a carburetor due to the destruction of the gasket or weakening of threaded fasteners;
• Mechanical sequel of removable saw equipment and other minor defects.

Before starting disassembly, you should verify the need for a more volumetric repair.

Independently assemble a new chainsaw after repair with initial quality, most likely it will not be possible. In the design of modern chainsaws, press plantings of conjugated parts are often used, which have minimal maintainability.

Even a partial analysis of a chainsaw with an improvised tool can lead to undesirable consequences. In most cases, to eliminate a malfunction, you can limit yourself to the dismantling of a separate node or system.

STIHL sawing device

The basis of the plant of this kind of model, indeed, all other chainsaws are a carburetor. But since we are talking about today about the Stihl 180 chainsaw, he will not leave the topic. So. The carburetor in this model has a single screw screw, that is, it is a kind of screw for setting the stroke of idle. While the jacket of the fully equipped load is in a stationary state.

In simple words we can say that it simply cannot be adjusted (see. here), while the adjustment of the full load simply cannot change. It is important that the carburetor itself at the factory was configured in such a way that, regardless of the fact of which the direct operation of the chainsaw is carried out, the air-fuel mixture is brought to the engine itself.

User manual

The passport of the gasoline saw “STIHL” MS-180 is the operating instruction, which collects complete information about the tool itself. Before starting operation, it is necessary to carefully study the management in order to avoid annoying malfunctions.

We offer to get acquainted with the instructions of the chainsaw.

Device

The “stihl” MS-180 chainsaw consists of: gasoline engine, carburetor, casing, starter, flywheel, clutch, decompression valve, oil, fuel pump and tank, spark plugs, saw chain, tire, stars, brakes, air filter, switching lever. dust quilter, muffler, fixators, tension wheels, gear stops, adjustment screw, handle.

Preparation of the Stihl chainsaw for work

The preparation of the saw should be approached with all responsibility, since the service life in the future depends on this, as well as the safety of the operator itself. Consider the correct algorithm of actions when preparing a chainsaw for operation:

• The assembly of the Stihl chainsaw is carried out (according to descriptions and schemes in the manual);
• the tire is worn and fixed;
• the chain is pulled;
• The fuel mixture is correctly prepared: gasoline is diluted with oil in a ratio of 50/1 (the amount of gasoline AI-92 5 liters., STIHL special oil for two.stroke engines 100 ml.);
• The fuel mixture is poured into the tank;
• The oil lubrication oil is poured into the tank;
• The reliability of the stretch of fasteners is checked;
• According to the instructions, the saw is launched;
• The carburetor is adjusted at idle by the corresponding screw (the chain should not move);
• The supply of lubrication to the chain is checked.

We suggest watching a video on how the assembly of the chainsaw “Stihl” is made:

Ours will tell us about how to start a chainsaw “Stihl” 180

Catching period for the chainsaw “Stihl”

In the usual sense, the run.in for the STIHL 180 saw is not carried out. She is originally ready for work. However, the owner of the equipment needs to know and understand the following:

The former from 4 to 8 broken full tanks with combustible operation of a gasoline saw should be performed in gentle mode not for the entire power of the power plant with frequent interruptions for cooling the tool. The first 60 minutes of the chainsaw “Stihl” consists of intervals of work and rest: 2 min. work, 10 seconds. idle, break

A idle speed of more than 10 seconds harms the spark plugs, leaving a dozen on them

It is very important to properly prepare a fuel mixture of high-quality materials (1/50, AI-92 and above, STIHL oil for 2 stroke engines)

Maintenance

• chain condition, sharpening;
• chain stretch;
• tightening fasteners;
• filling the fuel and oil tanks;
• the presence of a chain lubricant;
• idling and t. D.

After sawing work,:

• chainsaw cleaning;
• The tension of the chain is weakened (required);
• circuit sharpening (if necessary);
• tire condition, its wear;
• filter maintenance (as needed).

The newly.minted owners are often lost and are looking for materials on how to correctly disassemble (assemble) the “Stihl” chainsaw 180. We suggest watching a video where it is shown how disassembly and assembly of the chainsaw of the STIHL 180:

Malfunctions and repair

Stihl 180 chainsaw malfunctions and their elimination is another problem that excites the owners of the tool.

Why is the “Stihl” chainsaw 180 not starting up:

• there is no fuel mixture;
• no contact on the spark plug;
• cliff of high.voltage wire;
• The fuel pump does not pump;
• Fuel pipelines clogged;
• problems with candles;
• the ignition is not adjusted;
• Pouring a candle.

Why is the “Stihl” chainsaw not developing the right number of revolutions:

The “stihl” chainsaw 180 stalls at idle:

We suggest watching a video on how the carburetor of the “StiHL” ms 180 is adjusted with your own hands:

Some tool owners use the Stihl MS 180 chainsaw along with the nozzle-ugly grinder, this allows you to build a home sawmill and perform longitudinal cuts.

The video shows a nozzle-ugly grinder for the chainsaw “STIHL” MS-180:

But even without this nozzle, some craftsmen found a way to perform a longitudinal cut with a regular tire with a saw chain. We suggest watching a video about a home.made pilram from improvised materials:

The chainsaw is not started? Reasons and solutions

Basils have long been a kind of innovation and even more so are not considered exclusively a professional tool, because today literally every owner has such a universal device in his tools. And although there is a huge variety of types and models of chainsaws, in general, their designs do not represent something particularly complicated. With the correct use and maintenance of this tool, any problems with its work arise quite rarely. But what to do if a chainsaw does not suddenly start? The main thing is not to panic and in order to figure out what is the reason for the problem.

First you need to check the fuel level. If it is not enough, it is necessary to correctly prepare the fuel mixture, which should include the proportion of gasoline/oil indicated in the operation instructions (the oil brand is also indicated in the instructions). To prepare the mixture, use AI-92 gasoline correctly-this will get rid of many unnecessary problems. The amount of the mixture should be designed for 1-2 weeks of the chainsaw, t.to. gasoline has a feature of losing its octane properties.

The tool may not start because during its launch flows a candle of ignition. If this is true, then to solve this problem, it is necessary to turn the flooded candle and be sure to dry it (without pumping), drain the fuel from the candle hole and make a half.hour break. Then install either dried or spare candle in place. It is also important to pay attention to the contact between the tip of the candle and the high.voltage wire.

The completely dry light of the ignition suggests that the fuel mixture does not occur, which means that there is a certain problem with the carburetor. First you should clean the fuel filter. If after eliminating all available pollution, nothing has changed, it is necessary to do a carburetor. However, it is better to entrust its disassembly and cleaning to specialists in this matter.

If there is a spark, but the chainsaws still do not start, you will need to additionally check the air filter and the saeph. Air filter is easily cleaned of dust. In order to check whether the sapphone has clogged for leveling the pressure in the gas tank, it is necessary to disconnect the fuel hose and see how the fuel flows from it. If the stream is normal. the saopant is in order if there is no fuel or it flows very slowly. you need to clean it.

New chainsaw will not start

Often a completely new chainsaw cannot be launched the first time. With a cold launch of its engine, the switch is installed so that the damper is closed. Now you need to pump up the fuel into the carburetor, and then twist the launch hand well. It is considered normal, even if after 2-5 launches the tool starts up, but stalls. After that, you can transfer the switch to the position of half.gas, and then to the working position, and continue to start a chainsaw.

The reason that after the winter period the chainsaw refuses to work, it may be elementary. the fuel mixture has decomposed and lost its properties. To eliminate this problem, it is necessary to pour the old fuel, unscrew and dry the spark plug, season the chainsaw with a new fuel mixture and abundant the engine several times. After installing the candle in place and in the absence of other problems, the chainsaw will necessarily start.

General information

The characteristics of this saw are the reason for the pride of the German manufacturer. At the same time, the unit is a tool that is designed to perform a small amount of work. The tool is positioned for domestic use, which confirms the intensity of its operation, which should not exceed 20 hours a month. Having at your disposal such an unit, it will not be difficult for you to maintain order in your garden, to prepare firewood for the winter, as well as clearing the sites. At the same time, he will be able to help you in solving other tasks where there is no need to perform complex manipulations.

Main characteristics

The saw considered can be considered a compact option, because its weight is only 3.9 kg. At the same time, it has an oil and fuel tank of a large capacity. A two.stroke engine helps the device with its working functions, the capacities of which are enough to solve simple problems. In addition to this during operation, this tool does not create strong noise, the level of which does not exceed 98 dB. For ease of understanding, it is enough to say that a person’s speech creates noise at 76 dB.

• Stihl 180 chainsaw has a power of 2.6 watts. In principle, this is enough, remembering that it is a tool for household use.
• The oil tank capacity is 0.145 liters, fuel. 0.25 liters.
• The tire provided by the design has dimensions 350 mm, while the step is 0.325 inch.

Cumbbound device

As in the case of other saws, the role of the main device providing the launch is performed by the carburetor. Considering in more detail the carburetor, which is equipped with the chainsaw of the Stihl 180, it should be noted that it has a single setting screw. In other words, it is a kind of blanket adjustment screw. At the same time, the jacket, on which there is a full load, is all the time motionless.

In other words, adjustment against him is not applicable. In turn, there is no way to influence the full load. It is also necessary to pay attention to the factory settings, due to which the supply of the air fuel mixture is carried out directly to the engine. over, this principle is maintained regardless of the operating conditions of the tool.

The saw does not start: the reasons and ways to solve them

• Speaking about a saw 180, I must say that this tool has many advantages. At the same time, this unit and shortcomings are not devoid of. They will be given attention.
• The situation in which many owners find is widespread when the stihl chainsaw does not start and floods the candle. This is usually associated with the formation of a leak of oil used to lubricate the chain. The same happens for the reason that over time the site on which the oil pump and the oil tank hose joins, loses its former tightness.
• In principle, this problem is solved, but to do everything competently, you need to take into account the design of the chainsaw in question. This process itself provides for certain nuances, first of all, it is necessary to disassemble the unit, and without this it will be impossible to get to the required place.
• For many owners of this saw, the question is why the chainsaw of Stihl 180 is not started? Experts give the following recommendation on this subject: the first thing to do to those who encounter such a problem is to open and then close the lid located on the gas tank. There is another solution. you need to pull out the candle and let it dry. You can also create an artificial ventilation effect for the combustion chamber. Most often, these recommendations are enough to bring the device to the working condition again. However, this does not always help restore the work of the Stihl chainsaw.
• If there is a spark, but attempts to start a chainsaw do not lead to anything, then in this case you need to check the supply of gasoline, air filter, and then make sure of the candle with the working condition. Similar manipulations should be done for the reason that most often this kind of malfunction is caused by pollution. And if a cork is formed in it, then, of course, a vacuum environment will create in the gas tank, because of which the fuel will not arrive. Such a problem can be solved quite simply, for which it is enough to remove the pollution using the needle for this.
• Some owners are faced with such a problem when the saw itself started, but immediately begins to stall. Search for the reason that the saw is not started should be in the carburetor. Most likely, he managed to clog and therefore does not allow the tool to work correctly.
• To make sure that the cause of the malfunction is not a saepun, and it is in working condition, you must first disconnect the fuel hose from the carburetor, and then find out if there is no fuel leakage.
• Keep in mind that for a normally working chainsaw, the presence of a dense and stable jet of gasoline is a natural phenomenon. In addition, you can often observe a situation where the chainsaw of the STIHL 180 does not start hot and immediately stalls at the same moment or after a while. Usually such a malfunction is associated with a silencer. Most likely, it has accumulated many deposits associated with the long.term operation of the tool, which is usually accompanied by the formation of exhausts.
• At the same time, the saw may stop starting if the tool chain is poorly lubricated. Channels that have a cork can contribute to this, or if the reason should be sought in an oil pipeline that has a leak.
• A serious problem may be leaks in the connecting tubes or at the installation site of the fittings of the oil pump.
• There are cases when the stihl 180 chainsaw begins to stall due to the failed cylinder. To make sure if this is really so, it is enough to conduct an inspection. If as a result of the examination you find irregularities and chips, then this is a clear sign of breakdown.

Faulty candle: Methods for eliminating problems

• Sometimes during the verification it is possible to find out that the problem is a faulty candle. In this case, it is removed, then let it dry. Some owners may try to pump it, but this should not be done, because otherwise this element will be spoiled and after that it will only be thrown out. During the elimination of the malfunction, you will have to remove excess fuel by draining it through a special hole.
• It must also be borne in mind that the duration of drying should be at least half an hour. After completing such an operation, you can return it to its place, and then test it in the case.
• In some cases, the candle may fail due to the development of its resource. Usually, when this is confirmed, the only option for solving this problem remains. search for a replacement for it. In this case, it will not hurt to have a spare candle, and even better when you have a whole set of such elements at hand. In this case, you can always put a new candle instead of available and make sure that the non.working candle is the cause of the breakdown.
• At the same time, the inability to start a chainsaw can be caused by a weak contact, provided by a high.voltage wire and the end of the candle. The problem with the launch of the chainsaw may be associated with the failure of the ignition unit. In such situations, the only solution to the problem is the replacement of the faulty block, since it is not a repair supply.

Other malfunctions

• For many owners, the question regarding the correct idle after devastation of fuel from gasoline tanks is relevant. According to experts, you should not particularly worry about this. However, if you have to face a similar problem often, then it is enough to make manipulations with a carburetor, reducing motor speeds to restore the normal operation of the tool.
• In some cases, the owner may be required to clean the muffler, since this part may cause a malfunction. Performing this operation is quite simple. It must be remembered that many owners are faced with a problematic chainsaw due to a faulty carburetor.
• Although in some cases, eliminating the malfunction can be quite simple, but it is preferable if specialists will repair this equipment. After all, not every of us has the necessary knowledge and skills, and this is fraught with the fact that during the independent elimination of a malfunction, there is a risk of completely disabled the tool.

STIHL chainsaw stalls. does not develop momentum

All STIHL chainsaw systems function well, ensuring the launch of the mechanism. But sometimes, with confident work of idle, the saw does not gain revolutions at the load, interruptions begin in the motor. This means that there may be serious reasons requiring repair: to unbalance the carburetor screws, the end of the engine resource, breakdown of the candle or ignition coil, wear of the piston group.

But, most often, the engine does not develop turns, or may stall, when the check valve is out of order, a vacuum is created, which causes malfunctions. To repair the valve quite time.consuming, so it is better and faster to replace the oil tank cover, its cost is quite affordable.

The device of the plant

The first and almost main element of the chainsaw is the engine, namely the carburetor two.stroke (see. Carburetor adjustment). Its direct power is diverse, it all depends on the model of the device and its direct purpose.

The headset (saw) which consists of a chain (cutting), tires, stars, wheels (chain)

It is important that it always needs to be selected directly by certain characteristic engine data. Why the chainsaw of Stihl 180 does not start, and I did not drink why it stalls. Since the greater step has this kind of headset, the cut of the chainsaw will be deeper, you can even say that the more powerful and productive it will be. But do not forget that for the full operation of the device, the engine should also not concede it by power.

Its lubricant is carried out by means of special oil directly from the tank of the second, which is located on a manual block. It is worth noting that the mass of this kind of tank has such features that the oil and fuel, which is designed for the engine ends in the same time.

They figured out the general outlines with the device, but most likely with its basis, and now the time has come to start understanding why the chainsaws stopped working, what would be the life of this and how to eliminate them.

Return under warranty

The return of the defective product is possible only during the period limited by current legislation (within 15 days in accordance with Article 18 of the Law on Protection of Consumer Rights). At the same time, it is required that the tool is in the same state as the buyer was released-if any defects of the case or configuration were agreed, they should not be changed. Otherwise, the seller or manufacturer has the right to refuse the buyer to replace the chainsaws with a similar one or in a refund.

We will not give specific for service for obvious reasons. in each workshop, may vary due to logistics, accessibility of spare parts or mechanisms, as well as the level of remuneration. This does not apply to the official service centers of the manufacturer, often setting fixed tariffs for their services.

Service of the chainsaw STIHL MS 180

In order for your tool to work without any problems and breakdowns, you should remember several mandatory rules:

• Start warming up the engine only after checking the tension of the circuit, only after that you can turn on the power and start the engine factory. After the plant, it is necessary to warm up the engine, and only then start work. so the saw will maintain productivity and allow you to enjoy the use;
• The fuel mixture should be mixed immediately before using the tool. Do not interfere with the mixture “for reserve”. the fuel will break up into the fractions and will not let the instrument;
• You can store the tool only in a dry place, in a lubricated state, as well as with an empty fuel tank. otherwise, the fuel system can be corroded, respectively, force it to spend a certain amount of repairs;
• Do not let the chainsaw work more than the due date. the manufacturer installed it no more than twenty hours a month. Such an optimum was derived during the factory testing of the tool, and, accordingly, is aimed at extending the service life of the chainsaw.

Observing the rules of use specified in the documentation of the chainsaws, you can extend her life, and make it easier for yourself to work with the tool and not lose excessive funds for its repair.