Electric screwdriver chuck: description, function
The cartridge is a metal cylinder with a cavity inside, equipped with a ring and a regulating sleeve. It is fixed on the shaft. With its help, the drill or grinding attachment is securely fixed in it for further work. The fixation of the working body of the tool (drill) is provided by the thread. The drill is tightened in it in two ways. The first method consists in tightening it with a special key, in the second method, the drill tightens when the chuck is rotated in the direction opposite to the axis of rotation of the drill.
Cordless drill-electric screwdriver
Cordless drill-electric screwdriver Bosch PSR 18 Li-2.
A simple enough electric screwdriver for home use, the main advantage of the device is a universal lithium battery, suitable for jigsaw and delta grinder.
The weight of the electric screwdriver with the battery is 1.3 kg. That is, it is not heavy, but not light either. At the same time, the maximum torque is 46Nm, which is not very bad.
The speed is regulated, as in most other screwdrivers and drills. by a button. Also standard, a switch for the direction of rotation of the chuck is located next to.
The electric screwdriver has a standard three-jaw keyless chuck. The maximum diameter of the drill shank that can be clamped into this chuck is 10mm.
The manufacturer does not recommend using this electric screwdriver for drilling large holes: more than 10mm in steel, more than 35mm in wood.
To fix the bit or drill in the keyless chuck of an electric screwdriver, it is enough to fix the chuck with your hand and turn on the electric screwdriver at high speed.
Do-it-yourself electric screwdriver repair with cartridge play
A slight backlash within 1 mm usually does not create visible problems during operation. With a larger value, pay attention to the condition of the gearbox. So, the procedure is as follows:
- We unscrew the bolts securing the upper cover of the tool. We take it off.
- We unscrew the electric motor from the gearbox. Inspecting the mounts.
- We disassemble the gearbox. Often the cause of a breakdown is a malfunction of the bushing inside. It is possible to remove the sleeve using the steps described at the beginning of the article (see how to remove the cartridge manually). The sleeve is easily pressed out by hand.
- We are replacing the bushing. Then we collect everything in the following sequence: bushing, shaft, bushing bearings, retaining ring. Lubricating rubbing parts.
- After that, we assemble the gearbox in the reverse order. We attach it to the electric motor.
- We assemble the body of an electric screwdriver.
Do-it-yourself electric screwdriver repair when the chuck beats
The main culprit for this problem is the electric screwdriver gearbox. To make sure of this, you need to remove it by disassembling it in the above way. This particular failure may indicate several problems in the gearbox, which we will point out below. The reason may be:
- violation of the geometry of the gearbox shaft;
- production of gears;
- malfunctions of the shaft support bearing;
- wear of pins fixing planetary pinion satellites.
The above parts are produced only in factories, so you won’t be able to make them yourself. You just have to purchase them and replace the failed ones.
Create an account or log in to leave a comment
Комментарии и мнения владельцев can be posted only by registered users
Do-it-yourself electric screwdriver repair with cartridge play
A slight backlash within 1 mm usually does not create visible problems during operation. With a larger value, pay attention to the condition of the gearbox. So, the procedure is as follows:
- We unscrew the bolts securing the upper cover of the tool. We take it off.
- We unscrew the electric motor from the gearbox. Inspecting the mounts.
- We disassemble the gearbox. Often the cause of a breakdown is a malfunction of the bushing inside. It is possible to remove the sleeve using the steps described at the beginning of the article (see how to remove the cartridge manually). The sleeve is easily pressed out by hand.
- We are replacing the bushing. Then we collect everything in the following sequence: bushing, shaft, bushing bearings, retaining ring. Lubricating rubbing parts.
- After that, we assemble the gearbox in the reverse order. We attach it to the electric motor.
- We assemble the body of an electric screwdriver.
How to disassemble the chuck of an electric screwdriver
Despite the fact that today there are many models of screwdrivers on the market, they have one general approach to removing such an element as a chuck. We will now briefly describe it.
In order to unscrew it, you need to remove the screw that secures it to the shaft. It is located inside the chuck, the screw should be rotated clockwise. After you unscrew the screw, jerk the cartridge in the opposite direction with a jerk.
Attention! When you try to unscrew it by hand, you must put the drill at the second speed, if it is two-speed. When buying a tool, it is advisable to lubricate the screw with machine oil. In some cases, when this element does not want to give in, then you should put the tool at the first speed, hold it in your palm, and turn on the reverse to the left. The chuck should come off the thread easily.
Jaws jammed in the chuck of the electric screwdriver
Today, many people use such a tool as an electric screwdriver, so it is not surprising that there is a high demand for them. Very often the device breaks down, and the buyer rushes to the repair shop, paying money for the repair. You don’t always want to do this, of course, so in our article we will help you familiarize yourself in more detail with the device of an electric screwdriver. Some problems can be dealt with on your own.
We will consider various cases of breakdowns of an electric screwdriver, namely: we will deal with the most frequent breakdowns of such an important part of the tool as a chuck.
DIY electric screwdriver chuck repair
This is a movable element of the tool, which consists of many rubbing parts. In the process of work, it is exposed to wear resulting from the action of friction forces, impact forces and other factors on it. The beating of the cartridge, its excessive backlash can frighten an inexperienced craftsman. In some cases, it is not always possible to allocate time or money to contact a repair shop. Therefore, we will consider how you can do it yourself when repairing various tool malfunctions.
Do-it-yourself electric screwdriver repair when the chuck beats
The main culprit for this problem is the electric screwdriver gearbox. To make sure of this, you need to remove it by disassembling it in the above way. This particular failure may indicate several problems in the gearbox, which we will point out below. The reason may be:
- violation of the geometry of the gearbox shaft;
- production of gears;
- malfunctions of the shaft support bearing;
- wear of pins fixing planetary pinion satellites.
The above parts are produced only in factories, so you won’t be able to make them yourself. You just have to purchase them and replace the failed ones.
How to replace the chuck of an electric screwdriver
It will not be easy for an untrained user to replace it, because without the help of a special tool with your bare hands, you will not be able to do it. There are two ways in which it can be removed, and we will consider them further in our article. In order to change it, you should pay attention to the steps that we described in the article above. Dismantling is carried out with the following tools:
- Hex wrench. This is usually a 10mm L-shaped metal bar. It is necessary to fix its short part in the chuck, the long one must be resting against something, for example, on a table. We turn the cartridge, then remove it by turning the key.
We have covered a way to dismantle using a key. The way to remove the element manually is described above.
Electric screwdriver chuck: description, function
The cartridge is a metal cylinder with a cavity inside, equipped with a ring and a regulating sleeve. It is fixed on the shaft. With its help, the drill or grinding attachment is securely fixed in it for further work. The fixation of the working body of the tool (drill) is provided by the thread. The drill is tightened in it in two ways. The first method consists in tightening it with a special key, in the second method, the drill tightens when the chuck is rotated in the direction opposite to the axis of rotation of the drill.
Electric screwdriver chuck thread
Structurally, this movable element is fixed in the tool body in three ways:
- Fastening with a Morse taper.
- Threading.
- Securing the set screw.
Mounting with a Morse taper has been known for a long time and is as follows. The shaft has the shape of a cone, repeating the outline of the surface inside the chuck. the same cone. By combining them in a certain way, you get a reliable connection.
Docking the shaft with the chuck using a threaded connection consists in the presence of a thread at the end of the shaft, onto which a chuck with the same thread can be freely screwed.
The fixing screw is most often used as an additional fastener. Its head has notches for a Phillips screwdriver, as well as a left-hand thread. You can see this screw by unscrewing the cams that close it.
To find out what kind of mount your instrument has, you need to carefully inspect the body of the instrument. The designation for each type of attachment is different. For example, this: 1–6 В 10 will mean that the chuck is fixed by means of a B10 Morse taper, and nozzles with a shank diameter from 1 to 6 mm can be used to it. If there is such a record: 1.0–11 M 12 x 1.25. you will know that you should use nozzles with shanks from 1 to 11 mm, the metric thread has a section of 12 x 1.5 mm. Foreign manufacturers use indicators in inches, for example, 1.0-11 ½. 20 UNF.
In this article, we examined the main problems that arise during the operation of the tool, paid attention to such a responsible unit in the design of an electric screwdriver as a chuck. Together with this, we figured out how it is attached to the structure of an electric screwdriver, gave some advice on how to repair it with our own hands, and also tried to outline in general terms ways to solve repair problems.
When trying to insert a large diameter drill, the chuck of an electric screwdriver jammed. Is it possible to restore it?
an electric screwdriver can actually jam when trying to insert a drill of the maximum permissible diameter into the chuck. An electric screwdriver of absolutely any brand can jam, regardless of its price.
How to fix or open Black and Decker Cordless Drill Jammed Chuck, Stuck Chuck in 5 Minutes
The chuck of an electric screwdriver can jam not only because a drill of the maximum permissible diameter was used. This can also happen due to unevenly clamped “cams” in which the drill or bit is fixed.
The tool can also jam due to the fact that dust, dirt, particles of metal shavings and other construction debris can get under the “cams”.
Whatever the reason for jamming the chuck of an electric screwdriver, the first thing to do is to pour a special universal grease inside the chuck, wait 10-15 minutes and then knock with a rubber hammer (carefully, without strong efforts) on the chuck and on each of the cams.
The most common breakdown of screwdrivers is a jammed chuck. If you are faced with a situation where the chuck is jammed in the Hammer electric screwdriver, first you need to deal with the type of breakdown.
The chuck does not close
Typical breakdown, especially in cases where a large diameter drill is used in the work. When unclenching the holding cams, for example, when using a drill of the maximum diameter calculated for a given model of an electric screwdriver, there are situations when the device is unclenched, but does not want to bring the clamp together. In this case, the cartridge rotates, but the work is paralyzed. Uneven clamping of the cams, in which the fixation of the drill is broken, is also a common breakdown.
Algorithm for solving the problem: grease is poured into the cartridge, for example, WD-40. Time is given for its penetration into hard-to-reach places, usually 5 minutes is enough. To speed up the process, you can warm up the cartridge with a hairdryer. Next, the cams are tapped from different sides with a rubber hammer.
Alternatively, after the lubrication procedure, you can clamp the front part of the electric screwdriver chuck in a vice, and at the same time try to clamp the upper part with an adjustable wrench.
We remind you that the chuck clamping mechanism is an integral sub-assembly that allows the use of drills of various diameters in operation. If the chuck is jammed in the Hammer electric screwdriver, we recommend contacting the service center.
Bit a chuck in an electric screwdriver
The most common breakdown of screwdrivers is a jammed chuck. If you are faced with a situation where the chuck is jammed in the Hammer electric screwdriver, first you need to deal with the type of breakdown.
The chuck does not close
Typical breakdown, especially in cases where a large diameter drill is used in the work. When unclenching the holding cams, for example, when using a drill of the maximum diameter calculated for a given model of an electric screwdriver, there are situations when the device is unclenched, but does not want to bring the clamp together. In this case, the cartridge rotates, but the work is paralyzed. Uneven clamping of the cams, in which the fixation of the drill is broken, is also a common breakdown.
Algorithm for solving the problem: grease is poured into the cartridge, for example, WD-40. Time is given for its penetration into hard-to-reach places, usually 5 minutes is enough. To speed up the process, you can warm up the cartridge with a hairdryer. Next, the cams are tapped from different sides with a rubber hammer.
Alternatively, after the lubrication procedure, you can clamp the front part of the electric screwdriver chuck in a vice, and at the same time try to clamp the upper part with an adjustable wrench.
We remind you that the chuck clamping mechanism is an integral sub-assembly that allows the use of drills of various diameters in operation. If the chuck is jammed in the Hammer electric screwdriver, we recommend contacting the service center.
Every active user of the tool has encountered a situation when the clamping mechanism of the chuck of an electric screwdriver Interskol, Makita or any other brand has jammed. This structurally simple, but functionally significant unit is subjected to severe dynamic, vibration and shock loads. Dust, metal shavings and other small mechanical fractions also penetrate into it. all these factors lead, if not to fatal breakdowns, then to periodic malfunctions of the mechanism.
Types of malfunction
Typical cases in which the chuck of an electric screwdriver Metabo, DeWALT, etc. wedges:
- when trying to use a drill of the maximum permissible size, the cams are bred to the maximum, after which it is not possible to bring them together with the application of regular efforts;
- it is not possible to remove the drill or bit clamped in the chuck. the jaws do not open. Often at the same time they are clamped unevenly, which worsens the fixation of the drill.
Less often, the jaws jam during their free stroke when compressed or unclenched. usually this is facilitated by particles of debris, scale, shavings, etc., caught under the shaped part of one of the cams.
Repair methods
Experts recommend, regardless of why the electric screwdriver has jammed, what to do first: in the inner cavity of the chuck, including the surface of the cams, introduce a universal grease like WD-40. After 10-15 minutes, use a rubber hammer (or an ordinary one, through a gasket) with moderate effort to tap the chuck and the cams.
If the bit is jammed in the chuck of an electric screwdriver from Bosch, Texas, Praktika, etc., then (after lubrication) the use of two adjustable wrenches effectively solves the problem. One clamp the base of the cartridge, the second gently rotate its upper part. In order to avoid damage to the surface and the knot itself, you should use soft but dense skin-type pads.
If your efforts have led nowhere, with minimal financial costs and extremely quickly the functionality of the tool will be able to restore the specialists of the workshops of the company “Udachnaya Tekhnika Servis”.
You are using an outdated browser. This and other sites may not display correctly on it. You need to update your browser or try using a different one.
Why a bit can get stuck in an electric screwdriver
It doesn’t matter if the tool is expensive or cheap, it is not uncommon for the clamping device to jam. This happens in several cases:
- When trying to use a drill of the largest allowable size, the chuck jaws are bred to the maximum value, after which it is often impossible to compress them normally.
- A jammed drill or bit cannot be reached because the jaws cannot be opened. in most cases due to uneven compression.
- Jaws can jam due to free play during compression and expansion. This is due to the trapped debris, shavings, scale, which fall under the curly parts of the cams.
Unfortunately, in such situations, it is impossible to work with an electric screwdriver, despite its serviceability. It is possible to cope with the problem on your own, in severe cases it is better to contact the service center to specialists.
How to get a jammed bit out of an electric screwdriver
The electric screwdriver is one of the most popular tools for both professional and home work. The clamping device is subjected to the most severe stresses, therefore, malfunctions may occur. The question of what to do if a bit is jammed in an electric screwdriver, how to pull out a part, remains quite relevant.
How to open a stuck electric screwdriver chuck
When the described problem occurs, a natural question arises about how to pull the drill out of the electric screwdriver when the element is jammed.
At the first stage, professionals recommend pouring a universal grease of the WD-40 type into the inside of the chuck (touching the surface of the cams). Kerosene or engine oil can also be used instead. Such solutions are recommended for use in any case of jamming.
Jamming is often due to misuse
After 10-15 minutes, the chuck and the cams must be gently tapped through the gasket with a regular or rubber mallet. Typically, the grip is loosened and the drill is released.
If this does not happen, then it is allowed to slightly warm up the cartridge with a hair dryer and try to remove the bit again. The method is suitable for owners of screwdrivers with standard and quick-release fasteners.
The jammed bit can also be removed using two adjustable wrenches. After the lubricant is added inside, rather simple actions are performed:
- With the first key, squeeze the base of the chuck,
- The second. gently rotate the upper part.
It is recommended to place soft gaskets between the parts so as not to damage them while they are unscrewed.
Attention! In some cases, it is quite simple to cope with jamming. it is necessary that the cartridge has cooled down well after work. As a result, the cams will open and the bit will easily come out.
There is another method by which you can cope with this problem. It is necessary for one hour to completely lower the tool into a container with machine oil (even vegetable oil is suitable) or gasoline. After this period of time, remove the product and use the described methods to get the bit out of the clamp.
If you cannot carry out the procedure yourself, then it is better to contact a specialist so as not to spoil the instrument.
There are several methods for removing the drill from the chuck.
Features of removing bits when they get jammed on screwdrivers from different manufacturers
Basically, all models of screwdrivers are quite similar, so the methods for removing the bit when it gets jammed are the same.
- Bosch. In Bosch screwdrivers, you can get the bit by using two keys after pre-lubricating the chuck.
- Makita. The tools of this company are distinguished by their reliability and long service life. Bit jamming occurs, as a rule, as a result of debris falling into the cartridge. In this case, it will be possible to cope with the problem if you pour lubricants into the inside of the cartridge. In the absence of a result, other methods are used.
- Interskol. Products manufactured under this brand work well and for a long time, rarely break down. Removing a jammed bit is easy using the methods described.
- Other manufacturers. There are many instruments of different brands on sale. Metabo, Whirlwind, DeWALT, Diold, Caliber, Hammer. There are as many ways to remove the bat in case of a problem as with other models. It is allowed to try all methods to cope with the problem.
Do I need to repair an electric screwdriver if a bit is stuck there
Regardless of which model of electric screwdriver (Makita, Bosch or Metabo), at the initial stage, you can try to get the bit yourself. The element must be pulled out very carefully so as not to damage the rest of the parts.
Before removing the bit from the electric screwdriver, it is recommended to carefully examine the tool. If necessary, it should be cleaned, and then try to remove the stuck bit. As a rule, with such a problem, the electric screwdriver remains in working order, so it does not need a complete repair.
Always inspect the tool before work.
You will have to take the tool to the workshop if you cannot remove the element yourself, and with further attempts, damage may occur.
In keyless chucks, removing and inserting drills is quite simple. In such devices, the sleeve works by manual rotation. To prevent the cams from tightening too much, they are often equipped with locking elements.
Experts recommend that before installing the selected bit in its place, make sure that the tool is working. It is imperative to turn off the product from the network.
Attention! The bit jamming in the chuck of an electric screwdriver is most often the fault of the owner. To prevent this from happening, it is recommended to service the tool in time, monitor its condition.
It is imperative to check that debris does not get stuck in the cartridge, and clean it in time. When working, you need to ensure that the product does not overheat, give it time to cool down. If necessary, additional diagnostics are carried out in order to identify possible problems in time.
In difficult situations, it is not recommended to engage in self-disassembly, otherwise you can completely ruin the tool. It is better to ask specialists to do the job.
Master of Architecture, graduated from the Samara State University of Architecture and Civil Engineering. 11 years of experience in design and construction.
- Ideas and methods of painting stairs in the house to the second floor
- How a regular plastic bottle can deal with a blockage in a bathroom or toilet?
.-
Exploitation
When operating any electric screwdriver, you need to remember two simple rules. Let’s repeat:
- The mode of operation of the tool should correspond to the set goal. If drilling is expected, then you need to switch to 2nd speed with the obligatory rotation of the ratchet clutch to drill mode.
- When working with self-tapping screws / bolts / nuts, the 1st speed should be selected, and in order not to rip off the caps of the screws or bolts, the torque ring must be moved to a position that corresponds to the length / thickness of the fastener and the density of the material (selected empirically).
The cartridge, engine and battery are the three main components that require attention and care. The chuck must be regularly cleaned of dirt (our electric screwdriver does not have a chuck, but this is a general rule), the electric screwdriver must not be stored in a damp and / or unheated room, during storage, the reverse switch must be turned to the neutral (middle, stop) position (this position in our device, too). Regular battery recharging is also recommended.
At first sight
A weighty, albeit rather compact instrument is clearly intended for a strong man’s hand. Thanks to the matte plastic and rubber inserts, the electric screwdriver is securely gripped in the palm of your hand, even with cloth gloves. The manufacturer has chosen a soft color scheme, but such colors are almost never found in natural conditions, which means that an electric screwdriver can always be found with a glance in a heap of construction rubbish.
The transformer-like design, traditional for a modern instrument, provides a tolerable number of elements with pits and depressions. this is good, less dirt and dust will accumulate in these depressions.
electric screwdriver: torque
Torque is the force with which the spindle and chuck rotate. It is not difficult to measure the torque on such a simple bench (its detailed description is given here).
Screwdriver manufacturers always indicate the torque of their products. But everyone points out differently. Someone, without hesitation, writes the maximum shock moment (and with a clear overestimation of two or three times). Someone shows two options: soft and percussive. In the characteristics of the electric screwdriver under consideration, the moment is indicated as much as 25 Newton meters. Of course, this is not true. precisely, this truth has nothing to do with real exploitation. We do not use the maximum (impact) moment, since it lasts a fraction of a second. We always work only at the expense of a soft, constant moment. Which is very simple to define. Here it is:
Thus, the manufacturer lied only twice, this is far from a record. Some manufacturers act much more shamelessly, overestimating the torque by three to four times.
| 4.5 | 3.5 |
| 25 | 12.5 |
| fourteen | 7 |
| twenty | eighteen |
| 24 | fourteen |
| thirty | nine |
| 32 | 7 |
The torque obtained from our own measurements of 12.5 Nm is a very good indicator. Such power will allow without hesitation to drive a roofing screw for metal into a metal profile or wrap a long screw for wood into a thick log. It is difficult to name a scenario in which more torque may be required. Unless to tear off the caps from the screws on the neighbor’s fence. This is easily done with a torque of 20 Nm.
Characteristics
The main characteristics of the tool are presented in the following table:
Review of cordless drill-electric screwdriver Tonfon 12 V
electric screwdriver: battery
The complete charging dock delivers 2.5 A to its contacts at 12.8 V.
The LEDs on the top of the docking station work adequately: during charging, it lights up red, and when the battery is full, lights up green.
Everything is fine, except for one thing: battery charging takes a long time, more than three hours. But on the other hand, you can work from a full battery for about an hour almost without interruption. And it’s still a pity that the cunning seller removed the second battery from the kit.
electric screwdriver: an unscientific test that surprised
This practical test consists of screwing self-tapping screws 50 mm long and 3.5 mm in diameter into dry wood (pine). Some screwdrivers allow you to tighten more than 200 self-tapping screws in half an hour of continuous operation on a full battery charge. These are very good screwdrivers. There are also reverse examples. But the instrument in question was pretty surprising. It’s almost four hundred self-tapping screws! The hand joint ached for a long time after such testing.
How can you explain such an effectiveness of the tool? Logic dictates that such autonomy is achieved not only due to the capacity of the battery. The capacity of the battery is not space at all, the most common, 2000 mAh. Rather, we see the result of a successful selection of the engine and gearbox. Bravo!
Instructions
Who knows crumpled Chinese? Need help. No, don’t smooth it out. Translate. Without translation, we only understand the numbers. Judging by their presence, the manufacturer still tried to convey something useful to the user.
Hello, De can be brushed to the new podbati?
See Metabo Shop Andriy, I don’t have mercy, the brushes for this model are not available ok. You can replace dvigun at the fence. Anyway, you can turn to our service center. for a phone number near the mountain side, stink you in detail to give everything.
ruslan (03/21/2015) Rating:
the electric screwdriver is very good, I have been using it for 2 years, very convenient, the charge holds well.
Vovo (01/18/2014) Rating:
and Metabo doesn’t have an electric screwdriver on a battery like the se 4000sm5-55 on the 18v platform?
vova (01/18/2014) Rating:
having bought a set of battery-powered tools Metabo plus a drill is good angle grinder super perforator of norms jigsaw also norms of parquet flooring lack of turns and the ipaku will fail a bit of irritation
Ruslan (08.08.2013) Rating:
bought a shura for 2300 UAH. shurik’s kit included an angle attachment, 2 months after the purchase, the attachment of the angle attachment burst. I called the Metabo dealership and said that the service center would determine whether they would replace it or not. I came to the service center and said the guarantee will be determined by a Metabo representative. The next day they called back and said that these are accessories and they are not covered by the warranty. I bought the kit not cheap and then my brother says I’m sorry, but three years of warranty is for something else. Thank you guys for the (PROFESSIONAL) tool and warranty. R.S. We collect furniture, we treat the tool with care, there are no mechanical damages on the attachment, only the question arises about the quality of the tool.
Sergiy (03/27/2013) Rating:
I’m working with him for 8 months (I’m picking furniture), I don’t miss any of them. Poki scho sami plus:.light;. To sit by hand in the rutsi;. Nadovgo vistachak akum.;. Shvidka charging.
Alexander (03/22/2013) Rating:
Metabo-shop Yes, you really need to contact the service center in our city, there are plenty of them, thanks of course Metabo. I will report on the results. What cannot be said about bosh. From here, and such a lack of confidence in service centers. My jigsaw broke down 3 months after purchase. I turned to the service center and waited for about 2 months and I had to pay, they say, the warranty does not apply to those parts. they are worn out as a result of normal wear and tear.
Metabo-Shop (03/14/2013) Rating:
Alexander (03/13/2013) Rating:
6 reasons not to buy this electric screwdriver. bought this electric screwdriver and got upset! Immediately upon purchase, I drew on a small backlash of the cartridge, but I thought it should be so. cons 1. Yes, there is undoubtedly vibration at the second speed, but it’s not so scary. To hell with her as they say, but still there. 2. The backlight shines in the wrong direction. Where they looked and what they thought placing the backlight there. Yes, it is convenient, but only if the screw fell on the floor and highlight it to find if it is completely dark but no more. 3. Everyone says that the gearbox made of aluminum is not so, nonsense. Made of plastic 4. 2 years later, the backlash has doubled, and during idle switching on and off in second gear, a knock from the gearbox appeared. 5. And now the most unpleasant thing is the stopper that stops the chuck for a supposedly quick change of the working tool, in general, works every other time, does not stop, but scrolls. And now, in order to unscrew it, you need to do several turns. Not convenient however. 6. Rigid torque adjustment. (He screwed the screw, he did not turn until the end, and the gearbox began to snap off, rearranged it for one more division and then he screwed the screw to the very tonsils. could I look for something better!
Servicetechprom (02.21.2013) Rating:
I bought it today. I screwed 20 screws into the door. tired))) No problem. boring. Tomorrow I’ll give the workers a full test. drive in the field. For its performance and price, the device is more than. There are, of course, disadvantages 1. the case is full (the instrument is not a fix, plastic is flimsy) 2. I took it in a set with an impact. when starting, the engine at the wrench jerks as it dumbly. 3. They take doubts about the battery capacity of 1.5 amperes.
S.S. (04.12.2012) Rating:
In my opinion, with any 10 V screwdriver, if you can’t drill holes for production, this requires a more powerful and resourceful technique, even better. an electric drill. Makita is also a good tool, but I personally don’t like it, and thanks to the guys for the shares! everyone is so generous
Sergey (11/27/2012) Rating:
Like the previous speaker, he chose between this, Bosch and Makita. CONS: Metabo is slightly larger in size than its competitors and the handle, it seems to me, will be thicker. This is perhaps the whole negative. PROS: noticeably more powerful than competitors, 3-year battery warranty, lower price. Works smoothly, clearly and confidently. Everything was done very well and soundly. AT THE SPEED OF DRILLING AND DRIVING SCREWS, THAT IS THE SAME FOR METABO, MAKITA, BOSH. So, it seems to me, Valery, overlooked a little.
Valeria (11/26/2012) Rating:
Seized Drill Driver Freed Up. Makita DHP458. Jammed Chuck & Gearbox
I bought a tool According to all external data, it was a dream for furniture assemblers, and so it turned out. He’s already good, but I think I must be some kind of a minus. I was lucky and I returned it in time, exchanging it again for a Makita. when drilling for conformity, it has a low and slow rotation speed.
Nikolay (09.09.2012) Rating:
3 year battery warranty also applies?
rebus (14.08.2012) Rating:
Shura is pleasant at work. you will not say anything. only to remove the chuck from it had to suffer. So it was not filmed in any way. Not with your hands. not flatheads. not with an open-end wrench. not with a spanner key. Even the WD-40 splashed not measuredly into the gap. Only the key helped! But then it unscrewed and twisted like in a video on YouTube !
Alexander (07/05/2012) Rating:
Sadness, actually. Acquired Metabo PowerMaxx 12 serial number 1116710681 06/08/2012. It was not me who used it, but an electrician at my service station. A week ago, when releasing the tool from the chuck, he. this very cartridge has broken. Those. the sponges are jammed in the unclenched state. In this case, the outer holder of the cartridge rotates, and the jaws do not move at the same time. In general sadness.
Sergey (04/18/2012) Rating:
The tool is just super, thanks to Metabo for such a reliable and compact tool, I have been working with it for about a year, the most important plus in addition to reliability. smooth operation of the whole instrument.
Metabo-Shop (07.02.2012) Rating:
A set of bits is included in the Metabo PowerMaxx 12 PowerPartner kit: http://Metabo-shop.com.ua/product_info.php/info/p1921_MetaboPowerMaxx-12-PowerPartner.html This one has 1 bit in the kit.
I (06.02.2012) Rating:
Anatoly (13.10.2011) Rating:
Cool shura. Small size, comfortable, great twists. I took it for the house. I chose between df330 dummy and this one. The Powermaxx is slightly larger and smaller than the ratchet modes. BUT the battery warranty is 3 years, and it looks like it is somehow better made. In general, I am satisfied with the choice. I advise you to take.