The lawn mower starts and stalls what to do. The main problems with gasoline machines

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

• After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
• When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
• At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
• He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

• The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
• Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
• Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
• If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate can form on a gas tank day, which is due to which the tasks with the operation of the device appear.
• Excessive pumping of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
• Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
• trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
• Knives are removed from the car. some models will not work under this condition.
• Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
• From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

Features of the structure of lawn mowers

Most of the braids are controlled by pushing back, but there are also models that can be controlled by the steering wheel.

A certain type of device is designed for different works. Small people cope with the usual middle site, and large steering mowers are used for large lawns.

But all devices have the same structure. Let’s start with the body. Gasoline braids have aluminum and steel buildings.

Using the lawn mower that you choose for a summer residence, you can also mulch the lawn.Aluminum is used much more often, since such a case is durable, light and resistant to corrosion. Steel buildings contain a powerful and heavy engine.Electric lawn mowers are easier than gasoline and their case is made of plastic ABS. It is used to create car bumpers.

The piles of mowers should be large in diameter, so they will easily overcome irregularities. They also create less pressure on the Earth and do not injure the lawn. Bearings will ensure high reliability and durability.

Many manufacturers make two front wheels with rotary. This allows you to increase maneuverability. The front wheels turn around the axis and due to this you will not need to raise the mower to change the direction.

Let’s talk about knives. All of them are usually rotary and are located on the working val. The diameter of the knives determines the width of the capture of the lawn mower.

The rotor performs the following functions:

• knives support at a certain distance from the soil;
• quickly rotates and cuts the grass;
• has blades serving as a fan. The air flow from the fan carries cut grass into the grass collector.

All knives are made of high.quality steel.The grass collector is a large bag or plastic box with air holes. It is easily removed and the contents are thrown out.

Many braids not only cut grass, but can also grind it into flour. This process is called mulching. In this case, the grass collector is not used, since the greens after mowing will serve as a fertilizer.

Important! While working with the lawnical mower, follow the safety rules.

Do.it.yourself electric lawnies repair

Not only factory, but also homemade electric municipalities are failed. The main reason for stopping the electric motor is the loss of contact and the lack of power on the engine terminals.

Drawing of an electric lawn mower for example TBH 1650

Therefore, first of all, we check the presence of voltage in the supply outlet, the condition of the electric cord and the absence of its break. Then, if a collector engine is used, you need to check the condition of the brushes and replace them with strong wear. A manual lawn mower with a collector engine is characterized by increased survivability, but requires regular replacement of brushes.

Do.it.yourself electric coser engine repair

Hand lawn mowers with an asynchronous engine also have problems. The phase.digging capacitor often refuses, but it is problematic to make it in the field. The indirect sign of the capacitor failure is:

• pulling the motor at the time of feeding;
• strong engine heating even with low load;
• low speeds;
• A characteristic buzz.

Do.it.yourself electric municipal mower is made from improvised materials that may fail. If a malfunction is detected, in any case, you need to make sure that the voltage is supplied to the engine terminals, and in its absence, check the operation of the switch.

Do.it.yourself electric lawners made

If there is a voltage, a capacitor or brush is in order, then the most likely cause of the breakdown is the burned winding. In this case, the unit will have to be handed over to the repair workshop. Electric female assemblies are most often repaired independently, since all the nuances of its work are not taken into account when assembling the device.

The lawn mower starts and stalls

The constant operation of lawn mowers leads to wear of some parts, as well as breakdowns. This usually happens at the most inopportune moment. How to repair a lawn mower with your own hands? In what cases the situation can be corrected independently, and when the help of a specialist is required?

When the lawn mower does not start

Depending on the area of ​​the lawn and the growth of grass on it, the owners choose the optimal technique in characteristics. It is several types:

Also, the restoration of lawn mowers with your own hands will be required if the conditions of winter storage are inappropriate. For example, after use, there were no cleaning surfaces or there was no off.season preventive maintenance. As a result, various problems are manifested:

• frequent sharpening of the lamp of the lawn mower is required;
• just does not start a lawn mower;
• The motor starts up, but through a short gap the lawn mower stalls;
• malfunctions of the carburetor appear, which requires not only disassembly, but also cleaning with repair;
• Do.it.yourself renovation of the lawn mower is required with a significant reduction in power during operation.

You should not go to an expensive service center. Many problems can be solved with minimal costs and repairs on your own.

After each use of the tool, it is necessary to clean the cutting elements. Change the oil regularly and perform a minimum risk.

Problems with the mechanical part

The mechanical system in lawn mowers with different drives consists of the following structural elements and nodes:

• knife (rotary or cylindrical type) or fishing line;
• transmission mechanism;
• grass collector and grass emission devices;
• wheels, handles and housings.

The failure of the cutting element

The most commonly damaged (for example, bend) or knives are blunt, the fishing line for the trimmer ends. This is easily detected with a simple visual inspection.

The fact that the cutting nozzles have become swept away is evidenced by uneven cutting of herbal stems when the lawn mowed.

Over time, knife fastening can weaken. Their balancing during rotation is disturbed, and vibration, whistle, rattling appear. If the knives are damaged, then during operation the mechanism will begin to perform unguided, sudden, sudden movements. To eliminate the malfunctions of this kind, the cutting elements are set to the right position, replaced with new ones or repaired. If possible, then the blades are pulled again.

Sounds and vibration during work

Uncharacteristic sounds, vibration, rattling appear during the operation of the unit, when the fasteners of its structural elements are weakened: body, engine. These phenomena are more often found in gasoline models, because their motor fluctuates more strongly than the electric motor. To eliminate these phenomena, check all the connections, pulling up the bolts if necessary. It happens that the whistle during the operation of the unit arises due to the entry into an outsider that blocks the video in the aerator. In this case, it is enough just to get it so that the sound stops.

Cutting nozzles do not rotate

Often, when mowing a high herbal cover or hard herbal, cutting nozzles cease to rotate due to grass clogging. This problem in most cases (if it has not led to more significant negative consequences) is easy to solve with your own hands, just picking out a stick with a stick.

Damage to constructive details

Damage to the wheels, handles and housing rarely happen. If they are significant, then they change these structural elements. Methods of repair, with its possibility, in each case, depend on the material of broken parts. they can be plastic, aluminum, steel.

Brand break

With prolonged operation, the mower wear out, stretches, and then the belt breaks off. At the same time, the device’s gasoline engine works, but the knives do not rotate. Self.propelled models can also break off the wheel drive belt: then they stop and do not go. Sometimes the clutch cable simply stretches and it needs to be adjusted.

The most common breakdowns

Any technique sooner or later fails. It is important to know how to repair mowers, because not in all cases you need to contact the service center.

The braid does not cut the grass

In most cases, the cause is dumb or severely damaged knives. To achieve the best results, just change the knife every year. Choose a knife suitable for your model. When the knife is swept away, you can sharpen using electrofig or file. When sharpening, be sure to use goggles and gloves. Angle of sharpening on both sides. about 30 degrees.

Simple sharpening devices can be purchased in stores. Before installing them, it is necessary to turn off the mower from the network and adjust the cylinder positions in such a way as to highlight the maximum cutting gap.

In cylindrical braids, the gap between the knife and the cylinder should be less than the thickness of the sheet of paper. Some of the most modern models have built.in regulators with notches. In other cases, you will have to use keys and screwdrivers to carry out the necessary adjustments. Follow the uniformity of the gap along the entire length of the cylinder. To check the adjustment, insert a sheet of paper between the cylinder and a knife, slowly rotating with your hand. Gradually adjust on both sides until the paper begins to cut purely at each point of a motionless knife.

It is difficult to move the mower

• When the mower hardly moves along the lawn, you may try to remove too high grass and you will have to adjust the level of mowing. When seizing rollers or wheels, they need to be inspected to make sure that there are no scraps of grass and garbage. Most likely, they need to be removed and cleaned.
• If an interference for air is formed, then the lifting force will decrease on the mowing air pillow, and it will become difficult to move it. Air lack leads to overheating of the engine. Disconnect the power and remove the remaining grass from the air intake grilles.

Frequent breakdowns of the lawn mower: review and solution to problems

Using a gasoline lawn mowing for cutting the lawn, you need to be careful and follow the operating rules exactly. After completing the work, the device must be cleaned, since even a small clogging can block a moving mechanism. If frequent breakdowns of the lawn mower occur: the review and solution of the problems can be found by reading this article.

The reasons

The main reason for the malfunction in the work of the mechanism can be called the application for other purposes. Possessing knowledge about the principle of work and mechanisms of garden equipment, it is possible to eliminate problems with your own hands. But it is still better to contact a specialist, especially with serious breakdowns. Among the breakdowns that are most often found, the following can be distinguished:

Possible breakdowns

Despite the difference in the characteristics and appearance of various models of devices, they still have the same causes of breakdown, so they practically do not differ in the way to eliminate.

The most common problem in the operation of the device is that it does not start or stall when you press the gas. The reasons lie in the improper functioning of the carburetor or ignition, as well as in problems with the filtering system.

If the reasons lie in the ignition system, then you need to act as follows.

• It is necessary to make sure that you use completely serviceable candles, as well as that there are no traces of fuel on them. If the candle is flooded, it is recommended to carefully clean it, because otherwise the operation of the device will not be possible.
• If the threaded connection is too dry, then problems may occur when starting, since without lubrication with gasoline the spark will not appear or its power will not be enough to work.
• With breakdown of the ignition system, you should also check the contact between the candle and the high.voltage wire, since in its absence the occurrence of the spark will be impossible, as well as further operation.

If the device stops working 5-10 minutes after the start of operation at high speed loads, the causes may lie in problems with the air and fuel filtering system:

• The filter can be clogged, so when it heats up, the system ceases to be cleaned properly and turns off;
• The reason may also lie in that the part responsible for adjusting the pressure in the fuel tank is polluted and blocks the supply of fuel.

There are also more serious breakdowns, which can be quite difficult to cope with.

• The channels and nozzles of the device can be seriously polluted, so you can not do without a capital cleaning. And in order to clean them correctly, you need to use professional means and blow the parts with a powerful air flow.
• Often gaskets, which are an integral part of the system, wear out and also fail in the work system. They are not subject to repair, so you just need to replace them.
• Wanned pistons in operation can lead to a breakdown. That is why the details must be monitored and if necessary to change them.
• In addition, the cause of the breakdown may be a violation of tightness in the space of the carburetor.

Stalling the chainsaw at idle? There is an exit

If the saw at idle began to stall, then there are several reasons a priori, and it will not be difficult to find out even the owner of the new, if you follow the recommendations of our specialists, check everything correctly and delicately. So, the reasons for stalling the chainsaw at idle may be the following:

• reducing the throughput of filters of gasoline and air;
• malfunctions in the ignition system, also referred to as its abnormal work;
• spontaneous change in carb settings;
• elements of the gas pipeline system are faulty;
• a muffler or exhaust channels is clogged;
• the occurrence of defects on the piston, cylinder or other elements of CPH, defects on the valve;

Before checking the insides of the saw in the search, why stalls the tool on idle, you need to inspect it with all the external components for the presence of deviations, which may consist in possible deformations, as well as check the presence of fuel in the tank. Consider each of these situations:

• Check and repair the filter. With a clogged fuel or filter, an air engine receives an insufficient amount of air or fuel, or does not receive one of the elements at all, respectively, cannot fully work. We remove the gas pipeline hose from the Karb fitting, and send it to the working tank. Click several times to “swing” and watch the result. With a pure fuel filter, gasoline goes evenly, clearly, not jerking and vice versa. Air filter to check must be delicately so that sawdust, dirt do not get into the carb. After washing, purging or replacing it with a new one, we analyze the result whether the problem was in two or one of the filters.
• Check the ignition system and the candle directly. Her poor condition can provoke a refusal of a saw at idle speeds if it stalls when you give gas or at all at one moment do not start. So, the candle could pour fuel; a spark does not arise due to a huge amount of soot or a burned out element of a candle; The spark does not occur in case of violation of the gap between the electrodes (too large or small); A dry candle will indicate the absence of gasoline in the piston cylinder; Incorrect carburetor adjustment and a clogged air filter can be determined by the presence of black soot on a candle, soot on its electrodes.
• Why, to check the ignition and filters system, the saw further stalls on idle. the reason can only be a carburetor. It is necessary to find three adjustment screws, among which one is responsible for maximum turnover, the second. for minimal and idle passage (the screw is called “T”). You need to configure it according to the recommendations, strictly according to the instructions of each individual device. Even if the idle adjustment did not help, and drank at the same revolutions farther over. proceed to disassemble and inspect the whole crab. How to do this. we describe in our articles.
• Malfunctions, breakdowns, clogging of the muffler of the chainsaw. The last option that provokes a idle situation when the saw stalls. A muffler contaminated with sawdust and dirt, with adhering oils and exhaust gases loses its throughput. If it is not cleaned in time and not to change it, the engine will begin to “choke”. All elements associated with the silencer must be delicately soaked, neatly clean and blow out with compressed air, setting in their place. The engine at this moment is to close a rag to avoid dusting.

If your HUSQVARNA saw or a stihl bench instrument stalling the idle speed, we presented you all the existing verification options

It is also important to correctly collect all the details when disassembled in their former place, drain gasoline, if any, replace with a clean mixture and try to start the saw. Spare parts for chainsaws can always be ordered on the Kosikosa service

Professional diagnosis

One hundred are available not only for cars, but also for garden equipment. The service center is usually binded if the piston and carburetor of the device are defective. Why and why the lawn mower does not start in these cases, the master determines:

• Damage to the integrity of the device or individual parts. tonometer, put pressure to find the affected area, swing it.
• Channels, nozzles are clogged. elements are blown with air, cleaning liquids are used.
• Worn.out pistons, gasket. Replace the assembly.

Prevention of malfunctions

The rules for the operation of garden equipment are not complicated, if you follow these points, the device will last longer than expected:

• Always use high.quality fuel mixture.
• Do not work in the rain.
• Fuel injection into the carburetor using a primer.
• Pour the required amount of gasoline into the tank, do not allow fuel entering the engine.
• Mow with interruptions. Give the device time to cool and rest. The gas mower often does not begin to heat up.
• Clean the equipment only if the engine has cooled down. It should be cleaned: knives, channels, filters, containers. It is recommended to do this using special cleaning solutions. This will prevent the corrosion of metal elements.
• Store the device in dry, warm room, remove moisture.
• Do not press the device while working, make smooth movements forward, move on the platform. Random movements forward and backward. Wear the device faster.
• If you do not use the device for a long time. You need to replace fuel with a new. Gasoline stagnates in the system and does not allow it to function properly.

It should be noted that with the onset of cold weather, the car is exported as unnecessary, so it is recommended to drain all gasoline during this period (it is explosive under stagnant conditions). How to prepare a lawn mower for work after winter: check all the defects for defects, drain and replace gasoline, check the oil, start the car for the first time with a throttle or in a closed position.

The lawn mower stalls at high engine speeds

During operation, a situation arises when, when pressing the fuel supply key, the aggregate turnover begin not to increase, but to decrease. A malfunction of this nature can be caused:

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

How to get a lawn mower when the engine stalled at home

It is especially difficult to start a lawn mower after a long downtime. What to do to the user when a gardener refuses to work:

• If the device has not been cleaned for a long time, you need to rinse the air engine, it is cleaned with gasoline (it is advisable to do this every 24 hours of work). You can remove the filter from the device and start the unit, if the mower is working, then the reason lies in this.
• After winter, the remnants of old gasoline in the tank can interfere with the work of the device. The problem is easily eliminated if you replace the fuel with a new.
• Insufficient amount of oil in the crankcase. can also be the reason why the gasoline lawn mower is not started. Check its presence, is there a fuel in the tank.
• Incorrect location of the air damper during the first launch. At a temperature of ≥ 30 s. it should be in the middle position or closed. With repeated launch. open.
• Jamming the knee shaft, piston. you can eliminate if these details are slightly moving. The main thing is to do it carefully so as not to break the mechanism.
• Boarding of the Sapun. the supply of fuel stops, you need to clean the part.
• Dry threaded connection. while the factor does not have a spark of ignition, the connection of the gasoline should be lubricated.
• Failure of spark plug. accumulations on it oil, plaque. The candle is twisted, well dried, cleaned with a file. Excess fuel merges, dries at least 30 minutes. candle hole. Perhaps the part will have to be replaced if it fails to clean it.
• The contact of the high.voltage wire and a candle for the presence of a spark is also checked. If the latter does not arise, the ignition system is not allowed to determine and eliminate only in the service center.

Where to repair the lawn mower?

If the owner of an electric mower does not have sufficient knowledge, the repair of your favorite technique that allows you to maintain in good form the territory around the house will help to make service centers, which can be learned more on the sites:

• https: // Remontbenzogeneratora.com.UA/Services/Remont-Kos/Remont-Gazonokosilok/(Kyiv). Repair is carried out by highly qualified specialists, both at the location of the center and at the customer’s home. Departure of the Master in the city is free. They work with the equipment of all manufacturers, use high.quality spare parts. And they offer the whole range of services at affordable prices;
• Even high.quality and expensive models have an unpleasant habit. In order not to spend money on the purchase of a new lawn mower, she needs periodic service, which will help with high quality (https: // remontvsego.COM/TEH/SAD/Gazon/). The cost of the repair depends on the breakdown and amounts to the amount of 150 UAH. Departure of the master in the city is free, in the region (at a distance of 50 km one way). 8 UAH per km. Motor replacement will cost 250 UAH. ;
• “Master Engineering” is another service center of Kyiv, where the lawn mowers are being repaired efficiently and quickly (https: // wwww.Masterengine.com.ua/ru/remont.HTML/;
• From 100 UAH. Operational repairs in Kyiv in the company will cost to learn more about which on the website https: // kiev.Prom.UA/P82660097.Romont-Dvigatelej-Briggs.HTML?UTM_CAMPAIGN =%2528Portal%2529%2520%25D0%25A0%25D0%25B5%25D0%25D0%25D0%25D0%25D%25D1%2582%2520;
• From 50 UAH https: // kiev.Prom.UA/P239905849.Romont-Gazonokosilok.HTML;
• From 130 UAH (Kharkiv);
• Any problem will be eliminated in Minsk specialists of companies, a large list of which is given on the website https: // allService.by/Companies/Dacha/Remont_gazonokosilok/.
• Provide qualified assistance at https: // allService.by/Companies/Service_avtomobilei/1151.HTML/;
• At affordable prices, you can carry out repairs here https: // allService.by/companies/remont_oborudovanie_intsrumenta/275.HTML/;
• In the repair of garden equipment, the South.East Workshop 9 https: // Remont4Tehniki is engaged in.ru/), where the lawn mowers of such brands as Gardeha Gardena, Husqvarna-Husqvarna, Viking and many others will be returned to life. Repair terms are minimal, and the cost is determined by inspection.
• Employees after accurate diagnostics will perform work of any complexity. from replacing engine repair oil. Lay for repair work will be required: for diagnostics. 1200. adjustment and cleaning of the carburetor- 770, replacing a candle and air filter- 120 and 240, respectively; replacing the gase cable and move, the lips of the flywheel and himself. 400 and t.D. https: // www.REMSAD.ru/remont-gazonokosilok-i-benzokos/);
• (https: // Tehnoded.ru/servis/remont-gazonokosilok/);
• than 100 enterprises whose addresses can be found on this site offer their services for the repair of lawn mowers. https: // paM.UA/remont-gazonokosilok.HTML?no_redirect = 1/.

Good afternoon. There is a new lawn mower with the BS 450E engine company of the No-Brand lawn mower itself: on the first day, oil is flooded at maximum risk on the probe, a little gasoline has been added to the tank. Started with the first twitching of the cord, which pleased. Worked for about an hour and a half with frequent breaks. Without special problems. A couple of times it seems like out of the blue he stalled by itself, but the attention was not paid attention to this. I finalized the full production of gasoline until I started sneezing from its lack. Without gasoline is taken to rest. The next day the same gasoline has been added. (stored in a plastic canister made of plastic insoluble by gasoline) started with a second cord twitching, but the engine began to work unevenly, coughing or thumps. And it feels like not as the first day copes with the grass. Weaker mows. It was decided to mow so, in the hope that it will pass, warm. Not warming up. Sometimes stalls out of the blue, without hitting grass. Then it started from the second. fifth time. Finally stalled out of the blue and refused to start completely. (And this is on the second day of operation) gasoline is normal, oil is at maximum risk on the probe. The candle is twisted. the contacts are blackened, so they were cleaned with a small skin to shine. Just in case, the 60ml oil with a syringe is drained. The cleaned candle was returned to the place, while trying to start from 30-40 twitchies 2 second starts with a subsequent spontaneous stop occurred. A new candle was bought. the result has not changed. It does not start at all. After that, the candle was twisted and checked at the spark at the time of pulling out the starter cord. but it was not. How so? The plastic engine cover was removed, which on three bolts. And a visual inspection found that the wire stretches to the “interesting design” from the candle, which in some cunning address is in contact with the brake of the engine working from pressing the brake handle. Without going into the essence of work, the cunning system decided to clean the place from the factory paint in which the contact of the wiring coming from the candle with the design of the brake system of the engine could be lost. Когда лишняя краска была соскоблена и кончик медного проводка очищен от краски, попавшей на него при окраске косилки в черный цвет, то после установки кожуха при дерганьи шнура на свече стала появляться искра. The candle was twisted in place of the engine wound up and worked smoothly, without failures! Hooray. But having worked without a load of 30 seconds, suddenly began to fail again, working unstable. And even stalled. The casing was again removed, the contact of the wires was cleared better, the factory lubricant was removed in places where, according to engineers, the contacting parts of the brake system rubbed. After that, the mower started up, about 2 minutes later she began to work unstable again. But t. to. She did not stall, and the mowed quite normally, it was decided to work as it is. 10 minutes later she seemed to even work evenly, almost without failures than pleased. On the fourth day, the mower started up again the first time and the engine worked exactly but not for long. And literally a minute later he again began to work unevenly and with power loss. Stalls out of the blue. Started, worked evenly for the first seconds, then again unevenly and stalls. Finally refused to start. The casing is removed, the postings are tightly pressed around the place where it obviously loses contact with vibration. Merged oil (three.day) and flooded fresh! And after the assembly. started up again. At first, the engine worked evenly, then rolled up to the uneven work, but it was decided to mow until it stalled. But she did not stall. Worked and worked and after 10-15 minutes it became obvious that the uneven operation of the engine was almost disappeared. I worked out about 40-50 minutes. Without complaints to power. It remains to see what will happen next. Conclusion: poor contact of the wire coming from the candle (in the area of ​​the brake system) can cause a mowing refusal to work (it takes and stalls for no special reason) and the mowing refusal to start (t.to. no spark). But even if this contact is in order, then the question remains about uneven turns. Why is the braid after a slight downtime for about 5 minutes, it works evenly, powerfully, and then its even engine move is knocked on an uneven, the power is immediately lost and the grass is not so briskly. But if you do not pay attention to it, then after 10 minutes a mower, as if warming up, is already working powerfully again.

How to clean a carburetor?

You should start by checking the absence of open sources of fire nearby. You can not repair in a closed room. This is fraught with gasoline leakage.

• Unusual skateboards that go themselves
• Washing machine electric motor connection diagrams
• Sunny batteries of a country house

With a flat screwdriver you need to unscrew the screws to remove the plastic air filter casing from the motor. The extracted filter is checked, cleaned with a vacuum cleaner or replaced with a new one (if the condition is unsatisfactory).

You also need to remove the inner cover of the filter, which is located under the casing. This, unscrewing the bolts, is easier to make a cloth key. Air hose is attached to its inside, which will also have to be removed.

Finally, reached the carburetor of the device that can be dismantled. Disconnecting the fuel hose going to him from the tank, t.e. Having removed the clamp, the hose is turned, trying to remove from the pipe. You need to do work carefully. After all, in the presence of fuel in the tank, it will certainly spill.

The carburetor is attached to the engine with two bolts, for unscrewing which you will need a rolled head. Unscrewing the second bolt, try not to drop the carburetor so as not to damage the spring suspension.

The next step is removed the return spring. It is more convenient to carry out surgery from the side where it is attached to the motor. Now you can remove the cable responsible for the position of the damper, gently turning the carburetor counterclockwise.

Having removed the carburetor, unscrew the bolt fixing the fuel chamber cover.

Cleaning is carried out with a special liquid or WD-40 and a copper wire from which isolation is removed.

Finally, you can remove a plastic float located under the chamber cover that regulates the level of gasoline, for which the hairpin is pre.removed.

The camera must be cleaned of plaque. The insides of the carburetor are abundantly wetted WD-40 (or analogue), wiped dry. By repeating the operations several times, they clean the copper residential fuel channels, purge them, since their pollution is the main reason why the motor stalls or does not start.

Having done all the described steps, they collect the carburetor in the reverse order.

Having installed it in place, connecting the hose, air is expelled from the fuel chamber. The repair is completed on this.

After the described manipulations, the technique will start easily, and work stably.

Rules for the operation and storage of a lawn mower

In order for the lawn mower to start well and continue to provide it with good storage and operation conditions:

• During operation, carefully monitor the cooling system, carefully and in time, clean the channels in the case, as well as the ribs of the starter;
• If necessary, use solvents, kerosene and other detergents for cleaning;
• Do not clean the “hot” tool. let it cool;
• Stactly comply with the requirements of the instructions for the operating mode, otherwise you can overheat the engine;
• If you do not plan to use the lawn mower in the next month, the fuel mixture from it needs to be drained, t. to. Over time, it breaks up into heavy fractions, which will definitely clog the channels of the carburetor;
• After draining the fuel, let the trimmer work at idle until it stalls, this will help to completely remove the rest of the working mixture.

Before winter storage, take the following steps:

• completely disassemble the braid, rinse and clean all the details you can;
• Inspect the details for damage, if necessary, eliminate distortions, impulses, bent and any other malfunctions;
• Pour a sufficient amount of oil into the gearbox and clean the air filter;
• You can partially disassemble the motor, rinse, blow and smear all the moving parts;
• In order to lubricate the piston, you need to unscrew the candle, raise the piston with the outlet to the extreme dead point, pour a little oil into the candle hole and scroll the crankshaft a couple of times;
• If you store the lawn mower not in the house, wrap the engine with an oiled rag.

Remember, careful compliance with the rules will allow you to forget that the lawn mower is bad for several seasons.

Preventive work

For non.precise operations of the lawn mower, the owner must conduct its regular maintenance after the end of the working season, t.e. Before her premises for winter storage. This will cost cheaper than repair or buying a new electrical device.

Among the main measures that ensure the reliable operation of an electric mower is clean. The mowed grass accumulated under the neckline causes erosion of metal parts. The compressor or blunting will help to remove the remaining weeds.

The electric motor of the mowing is air cooling, therefore, it also requires a cleanliness that is a key to effective functioning. Suitable for cleaning the cooling ribs soft brush and compressed air.

Timely oil replacement specified in the use guide will become the key to prolonged trouble.free work, as well as the periodic cleansing of the air filter.

In the presence of a certain experience, it is easy to repair the lawn mowers with your own hands. The video below will help in this.

Benzotrimmer starts and stalls the reason

How not to get confused if the lawn mower does not start

The tool, despite its small dimensions, represents a complex technical device. If we study the operating annotation, there will be prerequisites why the lawn mower is not started, known and eliminated. It is necessary to alternately exclude the reasons that make it difficult to start the tool. They usually start with more affordable nodes with a slight checking check.

Diagnosis of malfunctions

The user first needs to check if there is a fuel in the tank. Starting in agreement with annotation, putting the saw on the side. Set the air damper to the position “Closed”, pump up fuel, turn on the ignition and produce 3-4 sharp jerks by the starter. If the engine has earned, open the air damper. The lawn mower is not started. we repeat the operations with a slightly open air damper.

The lawn mower cannot work for a long time. Gearbox and engine will overheat. Mowing less than 15 = 20 minutes, taking a five.minute break. In hot noon, the operating time is reduced by half. When mowing weeds, sedgers, the working hours are required to reduce.

If you are unsuccessful, we begin to find the reason for the refusal:

• check the quality of fuel;
• make sure the operability of the candle and the cleanliness of the candle canal;
• check the cleanliness of the air filter;
• Make sure that the fuel filter is not clogged;
• Check the cleanliness of the bastard;
• Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. DIY lawn mowing repair, if it does not start, will require patience.