Trimmer Stihl 38 Line Threading

How to put line in the Stihl.FS-38 mower

Took the mower out of the barn, but there was NO line in it, I had to put the line and on the occasion took off a small

How to correctly replace the line in the mowing head, reel of STIHL FS 55 lawn mowers

Coil with two working tendrils

In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:

  • One groove. both tendrils are wound together in one groove;
  • Two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

  • The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
  • One end of the line is inserted into the fixing technological hole located inside the spool.
  • The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
  • A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
  • The left end of the line is passed through the hole in the outer part of the reel.
  • The bobbin halves are assembled and put on the trimmer bar.

Trimmer Stihl 38 Line Threading

How to thread the line into the Stihl trimmer spool

How to insert line into the trimmer spool? Instruction

The guaranteed output of the factory trimmer refueling will inevitably require a line change. Having a very rough idea of ​​how to thread the line into the trimmer reel without the help of others, the newcomers are reluctant to take up this business. How to wind the line on the trimmer reel, how to thread the line into the trimmer reel. Autocut for stihl fs 55 trimmer line threading into the trimmer reel 2 part line winding on. But with some abilities, mastering this simple teaching does not present any difficulties, and the similar annotation presented below will greatly facilitate this process.

Coil with two working tendrils

In this type of spools, you should find the number of grooves for winding the line, lying on the inside of the reel:

  • One groove. both tendrils are wound together along one groove;
  • Two grooves. each tendril is wound on a personal groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded into them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixation of the antennae and assembly of the coil is similar to the one-groove option discussed above.

The first execution of this procedure, perhaps, will seem long and rather labor-intensive, but over time and experience this task will be solved much faster and easier.

Read more:  How To Wind A Fishing Line On A Husqvarna 148 Trimmer

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

  • Small electric trimmers with a working position of the motor and the coil in the lower part, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
  • Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
  • Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

  • Small electronic trimmers with a working position of the motor and coil at the bottom, usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on an evenly smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
  • Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special lamb: in such designs, you should hold the spool in a stationary position with one hand, and turn the wing nut counterclockwise to fix the Bobbin on the bar. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
  • Electronic and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a leisurely rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

For the second and third version of the coil, the suspension from the structure is disassembled by different methods. In the bobbins, the lamb is turned out from the lamb, in the coils, the latches are pressed from the latch, and one part of the coil is released from the other. How to tuck the fishing line into how to properly cheap fishing line. 2. On your site. If the halves of the spool are threaded, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds without the help of others. that’s enough for the user to properly fill the line. How to insert line into the trimmer spool? Instruction. How to remove the spool from the trimmer? How to wind the line in order to fill the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is impossible to make the winding by mistake: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

  • Round. the most durable;
  • Curly. for soft grass;
  • Twisted or notched. for thin grass;
  • Professional, suitable NOT for all instrument models.
Read more:  How to Mix Trimmer Oil

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to Specialized. Before tucking the line into the trimmer spool, it is best to soak it in water for half an hour. Then it will become more elastic and stronger.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. over, the methods of removal depend on the characteristics of the instrument. On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices.

On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbins and the spring inside it. On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.

How to fill the line in the trimmer so that working with it does not get tired

Many summer residents use a trimmer to combat weeds. a scythe with an electric or gasoline engine. It is convenient when working in hard-to-reach places for a lawn mower: in fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line, wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

Threading the line into the trimmer

The main question is how to properly wind the line on the trimmer reel, securely fix it there?

In the case of a device with one tendril, up to four meters of fishing line is unwound, one end is inserted into the hole inside it, fixing the fishing line, and moved in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind when it is assembled. If the groove has comments, then this free end is fixed with a finger. Then the coil is assembled.

How to refuel the trimmer coil if it has two tendrils? In this case, they check how many grooves there are. one or two. In the first case, both tendrils are directed into a common groove, if there are two of them, then each of them. into its own. 2-4 meters of thread are passed through the hole in such a way that the free edges of the thread are of the same length, and twist the bobbin in the direction of the arrow-pointer. The ends of the thread are inserted into the grooves or held with your finger, the device is assembled and attached to the trimmers.

In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent to the groove between them and the ends are wound simultaneously. Then repeat the previous assembly. With semi-automatic winding, the bobbins operate as follows. The fishing line is passed through a hole inside, its ends are fixed in the holes on the body, collect it and press the button. The thread can be easily wound in the correct direction.

It is important to remember that the cutting surface must be protected from solid objects so that it does not wear out. Otherwise, it will be necessary to constantly stop and, having removed the bobbins, replace the used fishing line. Let your work be NOT tedious and enjoyable!

See: How to Insert Line into Trimmer

Specifications

Trimmer type STIHL FS 38. portable. Mowing width in 1 pass. 38 cm. The tool in question is equipped with a gasoline two-stroke engine with a power of 0.90 l / s. The working volume is 27 cubic meters. See The maximum engine speed reaches 9500 rpm. The fuel tank is designed for 0.33 liters. The material of the deck and body is made of wear-resistant plastic. The bar is curved and the handle is D-shaped. With its dimensions, the lawn mower weighs only 4.1 kg. The line is 2 mm thick.

Mowing width, cm38
Enginetwo-stroke, gasoline
Power, l / s0.90
Engine speed, rpm9500
Fuel tank volume, l0.33
Working volume, cube / cm27

Performance properties

The STIHL FS 38 portable trimmer belongs to the amateur class. It is intended for the care of small garden areas. Such lawn mowers become indispensable helpers if it is necessary to tidy up the territory where it is impossible to use a wheeled lawn mower. For example, in hard-to-reach places, under trees and bushes, near flower beds and fences. The scythe is equipped with a simple and reliable 2-stroke engine of its own production. Carrying out work on a mixture of gasoline and engine oil. This engine provides simplicity of design, operation and service. And also high working power and torque.

Advantages and disadvantages

One of the most significant advantages of the STIHL FS 38 trimmer is that it can perceive a service position, in which it is more convenient to change the cutting attachment and wash the cover. This model is the lightest lawn mower in the entire trimmer range. Due to this, the user can easily cope with large volumes of work with minimal effort. Also, an important advantage of this model can be considered its lightness and compactness. This allows you to transport it on almost any type of equipment. The manual fuel pump allows the unit to be started even after long periods of inactivity and in cold weather conditions. Height-adjustable D-shaped handle ensures pleasant and comfortable working even for extended periods.

Read more:  How to Put a Piston On a Stihl 180

Scope and application features

The trimmer is the best replacement for the manual braid, which has served people for centuries. But technology does not stand still. The main area of ​​application of the considered trimmer model can be considered mowing grass and weeds in the local area. However, there are many other places where the lawn mower is considered an indispensable tool. In places where it is impossible to use a conventional wheeled lawnmower, a hand trimmer can easily handle. It is lightweight and very easy to use. For the Swath of hard-to-reach places, such as fences, trees and bushes. it is simply impossible to think of a better tool.

STIHL FS 38 portable trimmer. budget option

STIHL is a German brand for the production of high quality equipment, electrical equipment and tools. The founder of the company is Andreas Stihl. It was formed in 1926 in Germany. The company gained fame and recognition of professionals for the release of a reliable and high-quality line of chainsaws on the world market. Today, products under this brand are sold in more than 160 countries around the world.

Price. Design features

The STIHL FS 38 lawn mower is equipped with two handles. One of them is integrated into the body of the unit. it contains controls, an on / off button and a gas trigger. The other is a height-adjustable circular handle located on a curved bar. This provides the operator with maneuverability when working. In the design of this model, lawn mowers have a gearbox, as a result of which it is more budgetary. The FS 38 is equipped with a manual fuel pump. It supplies fuel to the carburetor and makes it easier to start a cold unit. The model in question already has a comfortable mowing head as standard. Threading the line into it is carried out directly on the unit, it is NOT required to remove or disassemble anything. Due to this, threading the line has become more convenient and easier. To increase productivity, you can additionally purchase a mowing head with polymer knives, as well as a reinforced one with a line. This will allow for faster work with tough grass.

Analogs

On the global and Russian markets, there are two brands that sell similar products. STURM and FUBAG. They are represented by the following models: German Trimmer FUBAG FPT 52 38712 and Russian Sturm BT8952D, which have similar characteristics and fall into the same price range.

The STIHL FS 38 trimmer. a functional unit you can trust

The STIHL FS 38 trimmer is probably familiar to all fans of quality gardening equipment. People who have once tested the brand’s products in practice rarely switch to products from other brands, because German quality conquers completely and completely.

This lightweight gasoline device is quite compact, it is ideal for cleaning small backyard areas. Many private sector owners prefer this “helper” because it does its job well and demonstrates a high level of productivity.

0.9 hp two-stroke engine from. Can handle heavy loads and the AutoCut mowing head can handle even taller bushes and weeds. D-handle easily adjusts to the height of the operator, so the NEW owner will be able to adapt the unit completely to himself.

Since the displacement of the engine is 27.2 cm 3, the Stihl FS 38 trimmer can reach a fairly high speed. The presence of a special quick start system eliminates the need to start the unit several times in a row, because it will start working on the first try.

Specifications and features

  • Mowing width: 23 cm;
  • Fuel tank capacity: 0.33 l;
  • Weight: 4.1 kg;
  • Bar: curved;
  • Line thickness: 2mm.

Thanks to the manual fuel pump, a person can easily pump fuel into the carburetor. This is especially important when the lawnmower has been idle for a long time. Constantly adding fuel will allow you to quickly start the device even after a “long vacation”.

For other useful information, see the following document:

The curved boom of the STIHL FS 38 lawn mower with a rounded handle is worthy of attention. Thanks to this design, the device easily copes with cleaning the area even in narrow or confined spaces.

All controls are located on a comfortable handle, so it takes a long time to look for where and what to switch is not necessary. During work, such a moment is very important, because the operator can NOT be distracted and without unnecessary movements adjust the operation of the machine.

Adjusting the carburetor lawn mowers Stihl FS 38

  • First you need to stop the engine;
  • Then install the mowing head;
  • The next step is to check the air filter, and if the filter element is not in good condition, it should be replaced;
  • It is necessary to completely return the idle speed adjustment bolt clockwise until it stops, and then 1.5 turns counterclockwise;
  • I started the device, you should wait until the engine warms up;
  • Using the idle stop bolt, the owner must correct the idle speed so as to immobilize the cutting tool.

It is not difficult to deal with all the procedures, the main thing is to get serious about the matter and tune in to work. over, many owners note that it is possible to independently carry out not only tuning the carburetor, but also replacing parts. Underlying schemes will be excellent assistants in this matter.

Pros and cons of the model:

  • Excellent performance;
  • Compactness;
  • Low weight;
  • Functionality;
  • Endurance;
  • Possibility of self-adjustment of the elements;
  • The presence of a manual fuel pump;
  • D-handle, etc.

Naturally, the list of positive aspects should include the verification of the brand itself.

  • The need to constantly check the fuel level;
  • Small motor resource;
  • Low power;
  • High cost;
  • Meager equipment.

The presence of not particularly catastrophic shortcomings of the model does not have a negative effect on the popularity of the unit, because the ideal technique simply does not exist.