Trimmer Works But Doesn’t Spin

Table of Contents:

Gasoline Trimmer Does Not Run Idling EVDIRAL.RU

The trimmer is not gasoline works on the idle

When purchasing a lawn mower, you must be prepared for the fact that, like in all other similar tools, breakdowns may also appear in it, which will require repair. But you should not immediately run to the service center and pay large sums to the craftsmen, convincing you of a severe malfunction in the device.

Perhaps the more widespread complaint related to gas trimmers is: “the lawn mowing stalls”. Gas trimmer: but it can not all. Works as a brush cutter. Naturally, a rather severe malfunction can also be a prerequisite for this. But in most cases the situation is even simpler than it seems at first glance. To cope with such a problem, first, try to understand its causes without the help of others, because after finding out the reason, it is even easier to fight the problem, and from time to time it will even self-destruct.

In fact, the circumstances, this is when the lawn mower stalls at high speeds, there are quite a few of these circumstances. Another is the presence of defects in the power system. Construction and repair that it just stalls, and not on a gas trimmer. In this case, the lawn mowing will stall on single revolutions. The trimmer engine runs quietly, the gearbox does not get very hot even at idle. Out of alignment or incorrect carb adjustment can lead to dilemmas with the power system. Vibrations that occur during the operation of lawn mowers can lead to misregistration. Incorrect adjustment of the lawn mowers can be corrected by simply adjusting it in accordance with the requirements indicated in the operating annotation.

Do not work idle

Benzotrimer (China) Idle adjustment, the coil spins immediately when starting at idle

Chinese benzo brought in for repair trimmer (pronounced spinning backwards, not have time to make how.

In addition, from time to time, gas trimmers can stall due to the fact that the valve located in the gas tank cover is simply clogged or stuck. To find out, try using the scythe by loosening the gas tank cap. If in this mode the device works appropriately clean the valve.

over, the lawn mower may stall due to the disgusting flow of fuel into the carburetor. Nevertheless, the repair i.e. It works normally at low speeds. Why, then, the device starts up, you ask? The reason for this is that at first the fuel gradually runs into the carburetor and it is enough to work at high power. lawn mowing does not idle. But then it is developed and at huge speeds, the engine begins to stall. As for the carburetor, the problem here may also be that its body is very tight.

Trimmer Works But Doesn't Spin

A prerequisite for the lawn mowing to stall at high speeds on gas may also be air suction. We are talking about the likely presence of a place through which air can pass during the heating of the motor.

Above all else, be sure to check the fuel intake hose. The problem may be that it is weakly held or cracked in general.

These are the main prerequisites why the lawn mower can stall.

Read the same

Why the trimmer does not work at idle EVDIRAL.RU

Build your own House!

When purchasing a lawn mower, you must be prepared for the fact that, like in all other similar tools, breakdowns may also appear in it, which will require repair.

But you should not immediately run to the service center and pay large sums to the craftsmen, convincing you of a severe malfunction in the device.

lawn mowing stalls at high speeds on gas

Perhaps the more widespread complaint related to gas trimmers is: “the lawn mowing stalls”.

Naturally, a rather severe malfunction can also be a prerequisite for this. I can’t start a trimmer. Why is the engine not turning when the engine is running? It only works when it’s worth opening it; the trimmer doesn’t work right away. On the choke. It only works when opening the air damper by 1 mm, I don’t think that the trimmer is. But in most cases the situation is even simpler than it seems at first glance.

To cope with such a problem, first, try to understand its causes without the help of others, because after finding out the reason, it is even easier to fight the problem, and from time to time it will even self-destruct.

In fact, circumstances, this is when the lawn mower stalls at large rpm, there are a lot of these circumstances.

Another is the presence of defects in the power system.

In this case, the lawn mowing will stall on single revolutions. It works only at idle. The trimmer is almost new. This is only possible if I can’t start the trimmer. The craton works on the choke. Stalls, mm by two. But she does not work. If the engine is idling, why does the engine work? Out of alignment or incorrect carb adjustment can lead to dilemmas with the power system.

Do not work idle

Chinese lawn mowing NO ILL-PREVENTION CARBURE ADAPTER / BC330 repair№2

When it’s hard to get a lawn mowing, you should pay little attention to fixing the carburetor, adapter and their seal

Vibrations that occur during the operation of lawn mowers can lead to misregistration.

Incorrect adjustment of the lawn mowers can be corrected by simply adjusting it in accordance with the requirements specified in the instruction manual.

In addition, sometimes gasoline trimmers can stall due to the valve located in the gas tank cap simply clogging or sticking.

To find out, try using a scythe by loosening the gas tank cap.

If in this mode the device works clean the valve properly.

over, the lawn mower may stall due to poor intake of fuel into the carburetor

Why, then, the device starts up, you ask?

The reason for this is that at first the fuel gradually runs into the carburetor and is enough to work at high power.

However, then it is developed and at high speeds the engine begins to stall.

As for the carburetor, the problem here may also be that its body is too tight.

The reason that the lawn mower stalls at high revs on gas, there may also be air leaks.

We are talking about the possible presence of space through which air can pass during the heating of the engine.

In addition, be sure to check the fuel intake hose. Why is it somewhere from 5 times, it works at idle and the revolutions of the stern ggt950b trimmer are not. The problem may be that it is weakly held or cracked at all.

These are the main reasons why

Read the same

Benzotrimmer Does Not Run Idling EVDIRAL.RU

Build your own House!

When purchasing a lawn mower, you must be prepared for the fact that, like in all other similar tools, breakdowns may also appear in it, which will require repair.

But you should not immediately run to the service center and pay large sums to the craftsmen, convincing you of a severe malfunction in the device.

lawn mowing stalls at high revs on gas

Perhaps the more widespread complaint related to gas trimmers is: “the lawn mowing stalls”.

Naturally, a rather severe malfunction can also be a prerequisite for this. How to adjust the carburetor at idle does not work does not. On the forward brush cutter even at idle (the gas trimmer shaft spins all the time all the time. The lawn mower stalls at idle. The gas trimmer and lawn mowing system does not work. But in most cases the situation is even simpler than it seems at first glance.

To cope with such a problem, first, try to understand its causes without the help of others, because after finding out the reason, it is even easier to fight the problem, and from time to time it will even self-destruct.

In fact, circumstances, this is when the lawn mower stalls at high revs, there are a lot of these circumstances.

Read more:  How to Repair a Trimmer Do It Yourself

Another is the presence of defects in the power system.

In this case, the lawn mowing will stall at idle. For what reasons, the Stihl 180 stalls at idle or at full throttle, at least some instrument is capable of breaking, and the stihl ms 180 chainsaw is no exception. lawn mowing does not idle. Out of alignment or incorrect carb adjustment can lead to dilemmas with the power system.

Chinese lawn mowing NO ILL-PREVENTION CARBURE ADAPTER / BC330 repair№2

When it’s hard to get a lawn mowing, pay little attention to fixing the carburetor, adapter and their seal

Do not work idle

Vibrations that occur during the operation of lawn mowers can lead to misregistration.

Incorrect adjustment of the lawn mowers can be corrected by simply adjusting it in accordance with the requirements specified in the instruction manual.

In addition, sometimes gasoline trimmers can stall due to the valve located in the gas tank cap simply clogging or sticking.

To find out, try using a scythe by loosening the gas tank cap.

If in this mode the device works clean the valve properly.

over, the lawn mower may stall due to poor intake of fuel into the carburetor

Why, then, the device starts up, you ask?

The reason for this is that at first the fuel gradually runs into the carburetor and is enough to work at high power.

However, then it is developed and at high speeds the engine begins to stall.

As for the carburetor, the problem here may also be that its body is too tight.

The reason that the lawn mower stalls at high revs on gas, there may also be air leaks.

We are talking about the possible presence of space through which air can pass during the heating of the engine.

In addition, be sure to check the fuel intake hose. Engine idling unstable engine does not need to. The trimmer is not gaining momentum, idling the mowing stalls. The problem may be that it is weakly held or cracked at all.

These are the main reasons why the lawn mower can stall.

Read the same

Why the trimmer stalls when you press the gas, at high and idle, when heating or opening the air damper

A spit that has a gasoline drive is a useful thing for owners of personal plots, lawns, and when the trimmer suddenly stalls, the work to clean the area from grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its breakdowns. The most common problems are contained in the instruction manual. To know the reasons why the trimmer stalls, you should be able to effectively repair the device yourself.

What could break

Problems with the lawn mowing due to the fact that this device does not start are classified in a certain way by service technicians. They highlight malfunctions with the following nodes of the mechanism:

  • an engine in which the piston and bearings may wear out or fail, crack the crankcase;
  • fuel supply system, while it is possible clogging the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • ignition circuit.

When you press the gas

If the lawn mowing stops when you press the gas, then the reasons may be as follows.

    The most common option is carb adjustment failure, which occurs with significant loads on the drive, after prolonged inactivity of the mechanism or when it is used in difficult conditions.

If the problem is related to the carburetor assembly, then it can be recognized by the appearance of vibrations of the lawn mowers.. When the hose bursts or the cable is stretched, these components are replaced.

At high speeds

When the braid stalls at high speeds, this is due to the following problems:

  • clogging or sticking of the valve located on the gas tank cover;
  • the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • air leaks;
  • fuel intake hose is cracked or loose.

Carburetor adjust, Based on the operating instructions for the trimmer. To adjust, it is often enough to loosen the tightening of its body. If there are problematic moments with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

At idle

At idle, common causes of trimmer stopping are the following:

  • contamination, misregistration or improperly adjusted carburetor adjustment;
  • clogged air filter;

Replacing the Lawn Mowers Air Filter

Trimmer air filter

  • reducing the speed of the gearbox when it is heated, which is a consequence of the use of an unsuitable fuel mixture;
  • throttle clogging;
  • air entering the system;
  • not enough fuel for lawn mowing.

Right after wound up

The unit may stall immediately after start-up, if the carburettor is misregulated or has been incorrectly configured, this causes uneven fuel supply. The result of this is that the device begins to vibrate distinctly. To troubleshoot, the carburetor is reconfigured according to the instructions for the mechanism.

Also the engine stops when it happens valve clogging, supplying fuel. In such cases, it is simple enough to clean it. If the lawn mower first worked, but then immediately died out, then perhaps the fuel enters the carburetor assembly with some difficulty. The easing of the valve helps to solve the problem, which ensures free circulation of the mixture in the system.

A stop can also be called. air suction in the presence of mechanical damage to the hose (holes, cracks) producing fuel. In this case, add revolutions to the drive in order to quickly expel air bubbles from the system.

When heated

lawn mowing often stops when heated. At the same time, it starts, works “jerkily” and gradually stops. This process occurs when gas in the carburetor boils or a shutter in it is installed rotary, and not disk type. In the latter case, the item is changed.

It happens that the trimmer heats up if ignition wire damaged either a coil. In order for the device to start working normally, replace parts.

When opening the choke

It happens that the unit stalls when the air damper is opened, normally idling. This is due to air leaks in the system caused by the presence of fuel hose cracks or problems with oil seals. Also, the carburetor dosing system may malfunction, while the lawn mowing will stop after opening the damper.

Carburetor fuel hose

All possible reasons that the lawn mower stalls, and methods for their elimination are contained in the next video

There are many reasons for stopping the lawn mowing, but the most common problems in operation are related to its carburetor. They can occur in any cases. The most problematic option is when a serious breakdown occurs, and you will need to purchase new parts or change the lawn mower.

Video: Trimmer Works But Doesn’t Spin


The best trimmer models according to buyers in 2018

UNION BTS-9252L trimmer

Hammer MTK33LE trimmer

Trimmer PATRIOT PT 3555 ES

Trimmer Huter GGT-800S

Trimmer Interskol KB-25 / 33V

The Trimmer Does Not Work At Idle EVDIRAL.RU

For what reasons Stihl 180 stalls idling or full throttle

At least some tool is able to break and the Stihl MS 180 chainsaw is no exception. Now let’s try to understand issues such as: why the chainsaw stalls with an increase in speed, also at idle and at full speed. Let’s look at options for diagnosing and eliminating defects associated with this behavior of the Stihl 180 chainsaw.

IMPORTANT. An experienced electrician has leaked the secret to the network how to pay half the price of electricity, the legal way. Read more

Why the chainsaw stalls when you press the gas

Let’s say the chainsaw is fine works on the single go, but with a sharp pressure on the gas stalls. What could be the reason? It is immediately clear that it is not a matter of ignition (the absence of a spark), because if there was a malfunction in the ignition and the absence of a spark, the tool would simply not start. Means fuel system remains.

There are a lot of defects in the fuel system and to determine the clear premise that the Stihl 180 chainsaw stalls when you press the gas, you need to carry out its full diagnosis. We advise you to read about the widespread malfunctions of the Stihl 180 chainsaw and their elimination.

Filter check

The first thing to check is the fuel filter.

In some cases, a clogged filter is unable to pass through the fuel mixture in sufficient quantities. Accordingly, a lack of fuel appears in the system, which leads to the fact that when you press the gas on the chainsaw, the fuel burns out, and a new one does not have time to arrive, as a result of which the Stihl chainsaw stalls. Also, with a clogged fuel filter, a noticeable drop in the power of the chainsaw at the highest revolutions can be observed, but this is with minor pollution.

Air filter

On the pages of the global network, you can find information that the Stihl 180 chainsaw may stall due to severe pollution of the air filter. I would like to refute this not entirely correct information, and to say that the Stihl MC 180 carburetor is equipped with a compensator that is designed and installed in order to take the air necessary for the normal operation of the Stihl 180 chainsaw, bypassing the dirty air filter. Of course, the power with a clogged air filter will drop a little, but it certainly will not stall. Also, power may drop due to piston wear, a Stihl MS 180 piston chainsaw repair will already be required.

Read more:  How To Wind Trimmer Line

Carburetor

One of the reasons why the chainsaw does not develop speed when you press the gas, but instead stall, is a carburetor malfunction. Let’s say the Stihl 180 saw worked properly, and then it was put on for a long time and did not use it. After it brought, and at idle he works good, and when you press the gas may stall. when trying to work, then when opening the air damper to 1 mm, I do not think that the trimmer. Why does it stall? The reason is a stuck carburetor valve nozzle. Of course, this is not 100%, but the probability of such a malfunction is high. We recommend reading the article about the device and repair of the Stihl 180 carburetor.

Read the same

In order to check the nozzle, it is necessary to remove the carburetor and disassemble it. To remove, it is necessary to unscrew the two nuts securing the air filter and the carburetor, and then remove the air filter and the engine control lever, while disconnecting the throttle control rod from the carburetor. Next, you need to slightly pull the carburetor towards yourself, and disconnect the fuel supply hose.

It is necessary to remove the fuel hose as carefully as possible, and prepare a plug for it in advance, since fuel should flow from it.

Having removed the carburetor, it must be purged and cleaned of dirt, only after that the carburetor can be untwisted.

It is necessary to untwist the cover of the main carburetor chamber, this is the one on which the compensator is mounted on top. Then with a bolt of 8 mm and a length of at least 50 mm. We knock out the valve.

Do not work idle

Chinese lawn mowing NO ILL-PREVENTION CARBURE ADAPTER / BC330 repair№2

When it is difficult to start a lawn mowing, you should pay a little attention to fixing the carburetor, adapter and their seal.

It is necessary to knock out the valve by installing the carburetor on a wooden stand, this will ensure its protection against damage to the body.

After the nozzle is removed, it can be purged with a compressor. The valve must allow air to flow in only one direction, if the valve can be blown freely in both directions, then it is faulty and must be replaced with a new one. It is necessary to assemble the chainsaw after the valve has been repaired, following the reverse disassembly sequence.

You can see clearly how the carburetor is being repaired, or rather how to knock the valve nozzle out of the carburetor body correctly by watching the video.

Another common reason why the saw may stall with increasing speed, air intake in the carburetor. This can only be checked with a special tool, but it is worth noting that if preventive work with the carburetor has not been carried out for a long time, then a new set of gaskets can be installed in the carburetor. In some cases, this helps to solve the problem with its depressurization.

When disassembling the carburetor to replace the gaskets, you need to carefully inspect its needle valve, press the rocker arm and check its lifting. Engine idling stalls or is unstable. Sometimes, especially after the Stihl chainsaw has stood for a long time with fuel in the carburetor, the needle may burn to the carburetor body and not perform its functions. Simply put, the needle valve will not let the fuel mixture through. In this case, the saw will not work.

Why does it stall at idle go

The first and most common cause of this malfunction is the incorrect carburetor adjustment. You can adjust the idle speed yourself, for this you need to have a Stihl adjustment screwdriver, which is supplied with the unit. The adjustment hole is located on the right side of the Stihl 180 saw on the handle and is indicated by the symbols “-” and “”.

Read the same

If the Stihl chainsaw does not keep speed and stalls at single on the go, you can be almost 90% sure that she has a violation in the fuel pump system, as a rule, this is air leaking into the crankcase through the pan gasket, or, much more often, through the crankshaft oil seals. Air intake reduces or completely stops the impulse, which is fed through special channels to the fuel pump of the chainsaw. As a result of this, the Stihl 180 chainsaw does not receive the required amount of fuel and stalls at idle.

Diagnostics can be done using a special device called a vacuum gauge.

The second way to check the efficiency of the oil seals is to pour gasoline into the engine crankcase and look at them if the oil seals pass gasoline, which means they cannot provide normal pressure in the crankcase, which will make idling impossible. And when working at high speeds, with leaky seals, there is a possibility of jamming of the crankshaft bearings.

The algorithm for checking the crankcase and Stihl 180 oil seals for leaks is as follows:

  1. The top cover is removed.
  2. The case is dismantled air filter and carburetor.
  3. The chainsaw handle is removed.
  4. The starter is untwisted and removed.
  5. The side cover and the drive sprocket are removed from the side opposite from the starter.
  6. A piston stop is installed in the spark plug hole or a cord from an old starter with knots imposed on it is stuffed into the cylinder.
  7. The flywheel and clutch are unscrewed, after which the parts are removed. It is worth knowing that the clutch of the chainsaw has a left-hand thread and is unscrewed clockwise.
  8. The gear wheel of the oil pump drive is removed.

Having disassembled the Stihl MS 180 chainsaw, you can see the seals, after that it is necessary to fill the crankcase with gasoline and to check the leakage. It is possible to fill the crankcase through the fuel window in the cylinder; for this, the piston must be lifted as high as possible. If leaks are found, defective oil seals must be replaced, or the pan re-sealed. Stihl 180 can be assembled following the reverse sequence of the algorithm.

Why stalls at full speed

You can often hear the question of why the chainsaw stalls at full speed. There may be several reasons. First, you need to consider how exactly the saw stalled. Let’s say the tool worked fine and suddenly, for no apparent reason, it suddenly died out and the starter does not crank. In such a situation, you can be 100% sure that the chainsaw is jammed and you need to proceed with its overhaul.

The second situation is when the Stihl 180 chainsaw worked fine, then gradually in a short time it lost power and died out, while overheating of the cylinder is observed. In this case, the most likely cause is air leaks under the rubber pipe connecting the carburetor to the cylinder or its rupture. only works after cleaning my trimmer has become idle. The mixture was leaner, resulting in overheating. You can eliminate the cause by changing the nozzle.

Conclusion

If the Stihl MC 180 chainsaw stalls at idle, does not gain power when you press the gas or stalls at full speed, it is necessary to diagnose the fuel system and check the crankcase for leaks. You can do it yourself, but you need to have certain skills. If you are not familiar with push-pull saws, it is better to contact specialists, because this technique is rather capricious and any mistakes are expensive.

Read the same

Why the Trimmer Stalls Idling

Prerequisites why the machine is not working on Idling

Injector idle adjustment

Does the situation depend on the brand of car

A little earlier it was accepted that only the engine of one of the VAZ family stalls at idle. Most car owners blamed on the design flaws of these cars. One of the possible reasons “why stalls on I can not have a trimmer idling. But later it became clear that a certain number of foreign cars, even very favorite ones, also have a similar disadvantage. Thus, the origin of your car does not have an even account of any importance, therefore, as owners of even the most popular brands have a chance to encounter such a nuisance.

So what happens to the car

Often, everything happens according to the standard scenario: you get behind the wheel, turn the ignition key, and the engine starts its work in normal mode. But it’s worth it for you to take your foot off the accelerator pedal, as the engine’s revolutions begin to fall immediately. It should be noted that in this situation, the idle speed sensor, as before, gives out the nominal number of turns. When working with a load, the trimmer then had to drive it idle why. Under all these circumstances, idle jumps, creating a distorted operation of the car as a whole. Due to the detonation of the propulsion system, which occurs against the background of jumps in idle speed, the most nasty, but completely natural thing happens. the motor stops working and the car stops.

Related posts

Clogged throttle

Usually the situation returns to normal after the next attempt to start the engine and set the car in motion. everything falls into place, and you can safely follow further along the intended path. But a similar incident can be considered the first bell, because in the upcoming such an emergency situation will again take you by surprise. Therefore, at the first manifestations of a similar obstruction, one should immediately address them. Before proceeding with the elimination of problems, it is worth knowing the real reason for their occurrence.

If the engine does not keep idle

And experienced workers of 100, and professional drivers with many years of experience, and even amateurs single out a group of events, as a result of which the engine does not hold momentum idle move. These include:

Read more:  How to Collect a Fishing Line in a Trimmer

Trimmer STOP carburetor adjustment.

Even more information about repair and tool selection on our website www.LookTool.Ru come in, we are glad to everyone.

Do not work idle

  • malfunction of the idle sensor;
  • throttle clogging;
  • throttle position sensor malfunction;
  • injector or carburetor contamination

The grounds for damage can be completely different, therefore, when they are eliminated, you will have to operate with all sorts of actions and techniques. If you have a considerable driving experience behind you, and you know the features of the car like the back of your hand, regardless of model, then eliminating this kind of malfunction will not cause you any problems. And all because such failures are not complex or serious. Why the trimmer stalls on the adjusted carburetor to idle. It follows that you can set up the car without assistance. Well, if the level of awareness or lack of free time does not give you the opportunity to eliminate all the defects yourself, it is better to seek the help of knowledgeable people who can save you from unpleasant moments in the shortest possible time.

Related posts

On the video. fixing a problem on a car with a carburetor:

How to solve the problem?

To deal with why engine stalls, it is recommended to consult a specialist. In this case, you can save your nerves and always save the missing time without breaking your head over possible ways to resolve this problem. High-quality service stations, with the appropriate equipment and professional workers, will be able to solve any problem and set up your machine in the shortest possible time. Here’s what the auto center can do:

  • complete replacement of equipment that has become unusable;
  • regeneration of failed devices;
  • carrying out preventive procedures and bringing equipment in proper form

The most optimal solution to this problem will be a complete replacement of non-working equipment. You can install a new idle sensor, throttle, its position sensor, injector or carburetor. In principle, most developed countries resort to this method today. With all this, it can be quite difficult to complete such a procedure due to the lack of spare parts necessary for your car or, if there are any, but of very dubious quality.

On the video. a solution to the engine idle problem:

Like it or not, you still have to restore worn parts on the car, in case of unsatisfactory operation at idle. And most often, given the financial possibilities, the owner of the car will risk taking up the matter with his own hands, so as not to spend a certain amount of money for specialists for the work done. If the Stihl chainsaw does not keep speed and stalls idling, why does it stall. Therefore, you should continue to think about possible losses. Remember: timely preventive maintenance, cleaning of parts and strict adherence to the car manual will help you avoid unpleasant situations. The type of engine. diesel or gasoline. does not play a special role in this case.

How to make the necessary repairs

To troubleshoot, clean the throttle and check that the idle sensor and the throttle position sensor are working properly. Why does the chainsaw not start or stall at idle? There are times when a chainsaw stalls at idle. If the work done does not bring the desired results and after restarting the machine problems arise again, then it is worth resorting to radical actions. This means that you have to make a complete replacement of the failed equipment.

On the video. auto repair with a faulty idle:

Each of the above circumstances causes the engine to idle. However, the driver will be able to avoid such troubles if he carefully monitors the condition of his car and its parts, which need constant care and routine inspection.

Related posts

Trimmer Stalls At Idle Causes

Prerequisites why the machine is not working on Idling

Injector idle adjustment

Does the situation depend on the brand of car

Some time ago it was accepted that only the engine of one of the VAZ family stalls at idle. Most motorists complained about the design flaws of these cars. However, it later became clear that a certain number of foreign cars, even very popular ones, also have a similar flaw. Thus, the origin of your car does not matter at all, because the owners of even the most prestigious brands have a chance to face this kind of trouble.

So what happens to the car

Often, everything happens according to the standard scenario: you get behind the wheel, turn the ignition key, and the engine starts its work in normal mode. However, as soon as you take your foot off the gas pedal, the engine speed begins to fall immediately. It should be noted that in this situation, the sensor idle move still gives the nominal number of turns. Under all these circumstances, idle jumps, creating a distorted operation of the car as a whole. Due to the detonation of the propulsion system, which occurs against the background of idle jumps, the most unpleasant, but quite natural thing, happens. the motor stops working and the car stops.

Related posts

Clogged throttle

Usually the situation returns to normal after another attempt to start the engine and set the car in motion. everything falls into place, and you can safely follow the intended path further. However, such an incident can be considered the first bell, as in the future, such an emergency situation will catch you by surprise again. Therefore, at the very first manifestations of such a problem, they should be addressed immediately. Before proceeding with troubleshooting, it is worth finding out the true cause of their occurrence.

If the engine does not keep idle

Both experienced service station workers, professional drivers with many years of experience, and even amateurs single out a group of circumstances due to which the engine does not maintain idle speed. These include:

Trimmer DIES carb adjustment.

Even more information about repair and tool selection on our website www.LookTool.Ru come in, we are glad to everyone.

Why does the lawn mower stall | lawn mowing | trimmer when you press the gas, on single rpm, hot

Why stalls lawn mowing when you press the gas: causes and their solutions. Stalls lawn mowing (trimmer):. on the single.

  • malfunction of the idle sensor;
  • throttle clogging;
  • position sensor malfunction throttle;
  • injector or carburetor contamination

The grounds for damage can be completely different, therefore, when they are eliminated, you will have to operate with all sorts of actions and techniques. If you have a considerable driving experience behind you, and you know the features of the car like the back of your hand, regardless of model, then eliminating this kind of malfunction will not cause you any problems. And all because such failures are not complex or serious. It follows that you can set up the car without assistance. Well, if the level of awareness or lack of free time does not give you the opportunity to eliminate all the defects yourself, it is better to seek the help of knowledgeable people who can save you from unpleasant moments in the shortest possible time.

Related posts

On the video. fixing a problem on a car with a carburetor:

How to solve the problem?

To understand why the engine stalls, it is recommended to consult a specialist. In this case, you can save your nerves and always save the missing time without breaking your head over possible ways to resolve this problem. High-quality service stations, with the appropriate equipment and professional workers, will be able to solve any problem and set up your machine in the shortest possible time. Here’s what the auto center can do:

  • complete replacement of equipment that has become unusable;
  • regeneration of failed devices;
  • carrying out preventive procedures and bringing equipment in proper form

The most optimal solution to this problem will be a complete replacement of non-working equipment. You can install a new idle sensor, throttle, its position sensor, injector or carburetor. In principle, most developed countries resort to this method today. lawn mowing stalls at idle It is necessary to exclude the reasons one by one, the trimmer stalls. With all this, it can be quite difficult to complete such a procedure due to the lack of spare parts necessary for your car or, if there are any, but of very dubious quality.

On the video. a solution to the engine idle problem:

Like it or not, you still have to restore worn parts on the car, in case of unsatisfactory operation at idle. And most often, given the financial possibilities, the owner of the car will risk taking up the matter with his own hands, so as not to spend a certain amount of money for specialists for the work done. Therefore, you should continue to think about possible losses. Remember: timely preventive maintenance, cleaning of parts and strict adherence to the car manual will help you avoid unpleasant situations. The type of engine. diesel or gasoline. does not play a special role in this case.

How to make the necessary repairs

To troubleshoot, clean the throttle and check that the idle sensor and the throttle position sensor are working properly. If the work done does not bring the desired results and after restarting the machine problems arise again, then it is worth resorting to radical actions. This means that you have to make a complete replacement of the failed equipment.

On the video. auto repair with a faulty idle:

Each of the above circumstances causes the engine to idle. However, the driver will be able to avoid such troubles if he carefully monitors the condition of his car and its parts, which need constant care and routine inspection.