Which Side To Put The Chain On The Chainsaw

How to properly put the chain and tire on the chainsaw: assembly

The procedure under consideration is quite simple. It is characterized by the following features:

  • First, the chain brake is released.
  • The tensioning screw is in close proximity to the tire.
  • The next step is to pull the cutter clockwise.
  • If it is difficult to move the chain, then it is necessary to loosen the fixing screw.

Modern designs of chainsaws greatly simplify the conduct of such work. Therefore, you can do it yourself, even in the absence of Special tools.

Which Side To Put The Chain On The Chainsaw

How to install a chainsaw cutter

After installing the chain, tighten it correctly and check the tension. Among the features of this moment, we note the following:

  • Too much tension is a prerequisite for overloading, therefore, the product may burst.
  • Insufficient tension leads to chain wear and many other problems.

In general, we can say that there are practically no problems with fixing an unworn product.

The chain is stretched

If the chain is used incorrectly or for a long time, it can be very stretched. This is due to the fact that the metal can deform over time. Too much wear and tear becomes a prerequisite for purchasing a new version, but it is possible to use the old one for a short period. Rapid stretching can be avoided only if the recommendations for use are followed. To carry out the work you need:

  • A hammer.
  • Pressure.
  • Welding machine.
  • Beards.
  • Pliers.

It is not difficult to put on the stretched version, but quite a few problems arise with the restoration, since the metal is characterized by increased strength. In this case, the main elements are fastened with rivets. The work is carried out as follows:

  • The product is fixed in Tesco.
  • If the work is carried out while using an angle grinder, then there is a possibility that the surface will be damaged, since this tool is difficult to control.
  • After crushing, rivets are knocked out. Do not throw it away as it can be reused.
  • Chain manufacturers DO NOT issue spare parts that are required for maintenance.
  • You can make a rivet with your own hands, but the work is quite difficult.
  • The product is divided into two parts. It should be borne in mind that the number of guides and the distance between them must remain unchanged.

When solving a problem with a long length, do not forget that the chain is NOT too short to pull. In addition, it is not recommended to apply oil to the saw chain.

How to put the chain on a chainsaw correctly

To perform a sufficiently large number of works, a chainsaw can be used. The main cutting element of such a tool is represented by a chain with different blades. Modern versions are characterized by the fact that they can be serviced independently. When cutting for a long time or if basic recommendations are not followed, the cutting edge wears out quickly. That is why it is necessary to remove and sharpen the chain, and then install it. This procedure is characterized by a fairly large number of features, in which we will talk in more detail below.

Poorly fixed drive sprocket

Quite widespread is the option when the leading sprocket is poorly fixed. It often detaches itself during operation. The solution to this problem is carried out as follows:

  • The protective cover of the engine and spark plugs are removed, after which the air filter is removed.
  • The next step is to remove the spark plug, which requires a special wrench.
  • A special plug allows you to fix the piston in the desired position.
  • The clutch plate is turned with a special key until the piston position changes, which must be located on top.

Then you can fix the sprocket in the correct position and solve the problem in question. The specified information indicates that such work is quite problematic, it is often carried out by organizations servicing chainsaws.

Chainsaw functions and device

In order to understand the features of the procedure under consideration, the chainsaw device should also be considered in detail. Among the features, the following points can be noted:

  • The main part is represented by the engine. In most cases, a single cylinder structure is installed, since this is quite enough for cutting.
  • The piston system is two-stroke, and the cooling is air. During operation, a small amount of thermal energy is released, so there is enough airflow to remove heat.
  • As with many other designs, this one requires oil, which ensures the smooth running of the moving element. The oil is added directly to the fuel. Depending on the design, oil and fuel are mixed in the range of 1:20 or 1:50.
  • The air filter can also be called an important structural element. Fuel is mixed with air to form a specific mixture, which is fed into the combustion chamber. If it does not constantly clean the filter element, then there is a possibility that debris will fall into the cylinder block. This will cause rapid wear or even jamming of the device.
  • A special design is presented as a starter, which is driven by a rope with a handle. If the rope is pulled strongly, then the flywheel is set in motion.
  • The main operating mechanism is a splint with a buckle. It is designed to guide the chain and secure it.
  • The classic chain consists of three teeth: leading, cutting, connecting. The fastening of the cutting edge is carried out using rivets.

A fairly common situation is the case when you have to pull the handle for a long time. It is due to the fact that the carburetor does not mix fuel with air correctly. In most cases, it is sufficient to configure the device in accordance with the operating characteristics. The chainsaw will last a long time if not properly maintained.

Why the chain flies. Find out the reasons

When considering how to install a chain on a chainsaw, you should also pay attention to what reasons lead to its East. There are three main reasons:

  • Incorrect bus operation.
  • Malfunction of the main elements.
  • Weak retention driven sprocket.
  • Strong chain elongation.

Each reason becomes a prerequisite for which quite a lot of difficulties arise with the use of a chainsaw.

Circuit voltage

Stretching can be done using two methods: fast and frontal. If stretch is used, then the installation of the chain on the chainsaw is carried out as follows:

  • The nuts are unscrewed.
  • The tire is held and lifted from the edge.
  • There is a special bolt, which is used to tension the chain.
  • The tire is lifted to eliminate the possibility of sagging of the web.

It is quite simple to do this work, it requires a small set of tools.

The clockwise chain tension is carried out in the case when there is not a lot of free time. The chain screw is securely fixed to eliminate the possibility of rattling at the time of operation.

Bus problems

Today, the problem associated with an unreliable fixation of the tire is often encountered. It is characterized by the following features:

  • The body with the guide element is fixed with a bolt.
  • The connection is provided by two plates, one of which is located on the body, the second on that, which is designed to guide the chain at the time of operation.
  • The drive sprocket and the tire support are protected by a special casing, which eliminates the possibility of damage to the main elements.
  • When the locking bolts are loosened, the structural element in question begins to move and vibrate at the time of operation. This problem can be solved by tightening the fasteners.

Other defects simply cannot be solved. In most cases, defects become a prerequisite for purchasing a tire and replacing it.

Step-by-step installation algorithm

Not all modern chainsaws are equipped with a setting wheel, which greatly simplifies the procedure for installing the saw blade. Systems with a setting wheel are generally a rarity among household chainsaws. Therefore, it is very important to know the technology and sequence of installing the chain on the chainsaw.

Key points to note:

  • Prepare a level surface on which you will assemble the chain and bar. This will minimize the chance of damage to the chainsaw or loss of small parts. A tire is laid out on the prepared surface and a parallel chain next to it.
  • Remove the sprocket protection, on modern chainsaws it is enough Unscrew the wing nut, on older models, you may need an appropriate size spanner.
  • In the base of the guide bar, the idler sprocket Turn all the way to the right. Only in this position is the chain installed.
  • Then the chain is successively placed, link by link, on the fixing groove on the guide rail. We install the chain from the top of the guide, gradually turn it so that the tire is always on top and the chain is on the bottom, this will allow it to always be taut and fit into the guide groove without problems. Be sure to wear thick protective gloves when performing this step, as your fingers will touch the cutting edge. Viewed from above, the cutter is always forward towards the end of the guide bar.
  • Put both the tire and the chain on the drive sprocket.
  • Secure the chain sprocket cover in place. Make sure all mounting pins line up with the holes. Incorrect installation with distortions or incompletely may be a prerequisite for extraneous noise, rattling.
  • Make sure that the guides “go” into the special mounting chute.
  • After installation, check that the chain is secure on the chainsaw and on the bar. Everything must be securely fastened without backlash.

An important point is the degree of tension on the chain after installation. Setting the correct tension is very easy and will take no pain in three minutes. First you need to loosen the nuts on the protective cover. Using the freely rotating adjusting screw, catch the correct tension so that the chain does NOT pull more than 3-5 mm from the edge of the guide bar.

It remains only to tighten the nuts and check the tension. If correction is needed, adjust the tension again.

How to install the bar and chain on the chainsaw, see the following. Which presents a clear algorithm of actions:

Why does the chain come off

Many, even the most experienced users of chainsaws, have encountered in their life a situation where the chain jumped off the guide bar during operation. The most common prerequisite is insufficient chain tension or wear.

In 80% of cases, the stretched chain links slip from the teeth of the drive sprocket, and it flies out from the guide under the action of centrifugal force. Although sometimes the problem appears due to an incorrect position of the sprocket on the axis of rotation or a loose fixed saw bar on the chainsaw.

Chain direction and which side to wear

A chainsaw chain, if you look closely, has saw teeth pointing to one side. Therefore, it is very easy to determine the correct direction of the saw teeth on the guide bar: if you place the chainsaw in the plane in which it is in operation, then a row of teeth are located on top of the guide bar, sharp edges should be directed to the end of the bar. While the row of teeth, which is located on the bottom of the chainsaw, with sharp edges should point in the opposite direction, towards the drive sprocket.

What to do if the chain sags

If the chain slack, there is a risk of injury to the operator. the saw blade could break or simply fly off the guide sprockets. Of course, modern chainsaws have safety and emergency stop systems, but these systems do not always work correctly.

It is important NOT to install a chain with defective or damaged saw links on the chainsaw, in addition to the danger of breaking at any time, such a chain will sharpen the guide grooves of the bar, which will lead to its distortion, uneven cut and failure of the guide bar.

Because of what the chain can sag during even short-term operation?

  • There may be problems with the guide bar. Sometimes, due to an oversight of the operator or due to severe wear on the threads of the fixing bolts at the point of attachment of the guide bar, vibration may occur, which causes a loosening of the chain tension. It is necessary to check the condition of the fixing bolts and, if necessary, replace them with new ones. When the bolts are tightened enough, these problems do not arise.
  • If you handle your chainsaw with sufficient care, any chain can wear out over time. Trying to repair it or collect one from several is a useless exercise. If the chain headset has stretched due to natural causes, then it is best to get a new one.
  • The asterisk is skewed. Sagging can occur due to the misalignment of the sprocket teeth. In this case, it would be best to contact a service center to repair and adjust the position of the guide sprocket. It is quite difficult to fix the drive sprocket in the correct position, because you will have to dismantle many small parts, remove the guide rail, and then assemble everything in the reverse order.

How to untangle a chainsaw chain

When removing an old chain or putting a new chain on the guide bar of the chainsaw, it can become tangled. It can also happen with careless transportation. When the chain is tangled, it folds into rings.

You need to put the chainsaw chain on a horizontal surface and spin the rings in different directions, while pulling the blade in such a direction that the diameter of the rings increases. Sooner or later, the chain will unravel into its natural position.

There is another way. you can rivet an equal link of the chain and straighten it, then connect it into a ring and rivet the riveted links back.

How to install a chain on a chainsaw

The chainsaw chain is the element that is subjected to the greatest stress and overheating. With such influences, it can break, fly off the guide rail, or simply become dull from prolonged use. For timely maintenance or replacement with a new one, you need to know how to independently remove the chain from the chainsaw and install it back. The step-by-step algorithm of THESE operations will be shown below.

Chain tension

The chain of the chainsaw together with the guide bar during operation experience the greatest stress, unlike other parts of the chainsaw. Over time, it lengthens in size due to boring gaps in the connecting links. This process occurs completely with all types of chains, therefore, when using a chainsaw, it is necessary to periodically monitor the correct tension of the chain and its wear.

Here are the chain states that depend:

  • The length of her life;
  • Safety of felling or timber breaking;
  • ICE resource.

If the chain is overtightened, the efficiency of the sawing work decreases, and the motor and transmission are subjected to increased loads. The guide bar heats up a lot due to increased friction, the operating mode of the chainsaw goes into excessive consumption of the fuel mixture.

Conclusion

There are many models of chainsaw chains on the market now. First you need to know what size is right for your chainsaw and NOT make a mistake in buying. The second step is to properly install it on the chainsaw. This is a somewhat time-consuming process, but if you know how to put on and adjust the chain yourself to track the tire, then the owner of the problems does not have to be advised. We tried to describe in detail the process of installing a saw blade on a chainsaw.

We hope that after reading this article, you will succeed the first time. But in order to minimize the occurrence of problems with the chainsaw and chain in the future, do not forget 3 basic rules:

  • If the chain is worn out and sagged, replace it with a new one;
  • If vibration appears during sawing and the cut is bad. watch the chain tension on the chainsaw;
  • Never use saw blades that are defective or repaired by dubious specialists, your health and those of those who are nearby are much more important than a little savings on buying a new and reliable chain.

Why does the chain come off

Many, even the most experienced users of chainsaws, have encountered in their life a situation where the chain jumped off the guide bar during operation. The most common prerequisite is insufficient chain tension or wear.

In 80% of cases, the stretched chain links slip from the teeth of the drive sprocket, and it flies out from the guide under the action of centrifugal force. Although sometimes the problem appears due to an incorrect position of the sprocket on the axis of rotation or a loose fixed saw bar on the chainsaw.

Check the stretch

To check the chain tension, you must disengage the saw brake system. Then manually hold the chain on the bar, if it runs smoothly and does NOT sag, then everything is fine. If the chain runs very tightly, then it must be slightly loosened, as there is a risk of breakage during operation.

How to untangle a chainsaw chain

When removing an old chain or putting a new chain on the guide bar of the chainsaw, it can become tangled. It can also happen with careless transportation. When the chain is tangled, it folds into rings.

It is necessary to put the chainsaw chain on a horizontal surface and spin the rings in different directions, while pulling the blade in such a direction that the diameter of the rings increases. Sooner or later, the chain will unravel into its natural position.

There is another way. you can rivet an equal link of the chain and straighten it, then connect it into a ring and rivet the riveted links back.

Operating tips

It is not enough to know how the chain is tensioned on the chainsaw. You need to properly care for the saw, then you extend the life Not only tenaciously, but the entire mechanism. Here are some tips for use:

  • Clean the air filter regularly and lubricate it with oil. Replace the filter with a new one if necessary.
  • Before starting work, always check that all nuts and bolts are tightened so that there is no malfunction during operation.
  • Lubricate the bearings regularly and remember to clean the spark plug.
  • Lubricate the driven sprocket. And after working with your chainsaw, don’t forget to clean it.
  • We lubricate, sharpen and tighten the chain always on time, then there will be no problems with the bar and the chain.

If you follow all of the tips above, your device will last much longer than the warranty period.

The chain is an important structural element of a chainsaw. It is she who has the greatest load during work, so high-quality and systemic care is required. When using any model, it is important to know how to put on the chain correctly. Watch out for its tension. If it is not secured correctly, there is a risk of stretching and coming out of the grooves. Reduced saw performance and increased risk of injury at high power.

Fitting the tire on Stihl and Husqvarna

Chainsaw models from the manufacturer Stihl may differ during the assembly process. Step by step guide:

  • Open the wing nut, remove the chain sprocket cover. Return it on the tire all the way to the right.
  • Place the chain on the bar, starting from the top, the cutting tooth on the top side must point straight ahead.
  • Attach the assembled tire to the chainsaw, pull the structure over the sprocket. Slide the guide onto the shoulder bolt. Close the cover, hit the pins in the holes provided by the manufacturer.
  • Turn wing nut until sprocket cover is in contact with motor housing.
  • Clamp bolt back forward, drive links Must fit into bar grooves. Tightens the wing nut completely.

At the end of work, check the tension, if the headset does not move well, adjust the tension with a nut. Engage the chain brake before starting.

The Husqvarna saw chain installation algorithm is almost identical. The main difference is that in most models, the tension and adjustment of the position of the headset to the body is controlled not by one, but by two wing nuts. A separate adjustment lever is rarely found on the protective housing of the outer sprocket, therefore the tension should be adjusted only with bolts.

Bus problems

When there are problems with the bus, the clinker tension is almost always relieved. Usually this problem occurs when the tire is fastened.

This space is located in a groove between the outer plate, which is located on the chain set body and the inner plate located on the motor body. The housing with the busbar is fixed with a bolt. This attachment is called the “engine assembly”. Drive sprocket and tire supports protected by special covers.

If the locking bolts are loose, the tire starts to move or vibrate. If the tire is intact, then the chain tension should be normal. After stretching, she will spend at least five working days without braces. Therefore, it is necessary to tighten the bolts that securely hold the tire.

Conclusion

There are many models of chainsaw chains on the market now. First you need to know what size is right for your chainsaw and NOT make a mistake in buying. The second step is to properly install it on the chainsaw. This is a somewhat time-consuming process, but if you know how to put on and adjust the chain yourself to track the tire, then the owner of the problems does not have to be advised. We tried to describe in detail the process of installing a saw blade on a chainsaw.

We hope that after reading this article, you will succeed the first time. But in order to minimize the occurrence of problems with the chainsaw and chain in the future, do not forget 3 basic rules:

  • If the chain is worn out and sagged, replace it with a new one;
  • If vibration appears during sawing and the cut is bad. watch the chain tension on the chainsaw;
  • Never use saw blades that are defective or repaired by dubious specialists, your health and those of those who are nearby are much more important than a little savings on buying a new and reliable chain.

Installing the chain on a chainsaw, how to properly pull and check the tension

If you have a chainsaw at home, you should know that this requires special care. It is necessary to periodically clean and sharpen the chains, clean the air filter, oil supply and tires. And, of course, you need to watch out for the chain stretching, as with poor stretching there is a trait not only to damage the dust, but also your health if the chain flies off at high speed.

Chain direction and which side to wear

A chainsaw chain, if you look closely, has saw teeth pointing to one side. Therefore, it is very easy to determine the correct direction of the saw teeth on the guide bar: if you place the chainsaw in the plane in which it is in operation, then a row of teeth are located on top of the guide bar, sharp edges should be directed to the end of the bar. While the row of teeth, which is located on the bottom of the chainsaw, with sharp edges should point in the opposite direction, towards the drive sprocket.

After removing one or more links (depending on the degree of chain stretch), the chains can be connected. We connect with old rivets while pressing them tightly on the sides.

Then we need a welding machine. The rivet should be welded to the sides of the line. After that, we remove the excess with the file that was formed during welding. The chain can be considered functional.