Why is the new trimmer for the grass eat a lot of gasoline. Classification of lubricants

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

• After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
• When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
• At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
• He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

• The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
• Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
• Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
• If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate can form on a gas tank day, which is due to which the tasks with the operation of the device appear.
• Excessive pumping of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
• Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
• trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
• Knives are removed from the car. some models will not work under this condition.
• Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
• From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

Carburetor operation instructions

Gasoline that enters this device should not contain mechanical impurities. All parts are treated only with gasoline. The use of the solvent is not allowed, because the elasticity of the washer and rubber parts is damaged.

To dry the details, use the purge of compressed air. It is not recommended to clean the small holes with wire or needle. Installation after repair or cleaning should be carried out moderately so that there is no wrist and deformation of the parts.

The float chamber must be connected to the body hermetically. Before operation, it is necessary to check the connection of the air filter. There should not be gasoline leaks.

Before starting the engine, you should prepare a carburetor. To do this, make sure that gasoline does not occur from it. To do this, just open the fuel valve. Block the air damper, and tighten the control lever all the way. The throttle is open 1/8 1/4 of the largest move.

At a low air temperature (below 5ºС), squeeze the drowner until a fuel appears from the hole.

During the start.up, slightly open the air damper, and after warming up the engine, open it quite.

Repair K-45: Main recommendations,

In order to fix the carburetor with your own hands, we offer to familiarize yourself with the repair of the Neva MB-2 motor block.

• If an extra amount of air enters the ICE chamber. Try to change the gasket between the head and the carburetor and tightly tighten the fasteners on the connection. If this did not help, the prerequisite may be wear of the shaft on the damper or the holes where it is connected. Such a shaft is subject to substitution, and in the case of broken holes, the device completely changes.
• When a lot of fuel enters the float camera. In this case, check and change worn details: float, jet, needle.
• If there is not a lot of gasoline in the carburetor, check the filter and sump, fuel supply hoses and gas tanks. Dirty elements need to be washed or changed, and if the tank rusted from the inside, you will have to clean it with caustic soda.
• If there is an increase in fuel consumption, configure the carburetor, turning to the operating annotation.

The device of the lawn mower

The device of the Stihl FS 55 lawn mower should be clear for you if you plan to operate equipment, and all the more to repair it. The internal combustion engine in this unit is almost the same as in the chainsaw. But the tire of the latter is fixed to the motor gearbox with a long tubular rod. Snutri houses a shaft that transfers torque from the engine to a working tool. This design is suspended on a belt that is thrown over the shoulder. This allows you to delay the tool on weight, which is fundamentally with a sensitive mass of the chainsaw.

The handle is fixed to the unit rod, using it you can move the end of the bar with the working inventory. Stihl FS 55 lawn mower, which is presented in the article, from the person’s side, the person has a protective shield in the form of a casing, which excludes injuries during operation. The tool itself is a round drum, on both sides of which a thick fishing line for a trimmer comes out of the holes. Adjustment of the carburetor and chainsaw repair Stihl Stihl FS55 FS 38 Carburetor. When the drum is spinning, the trimmer fishing line is pulled under the influence of centrifugal force and hit the grass, cutting it.

Stihl FS 55 lawn mower, the technical properties of which will be presented to your attention below, has a fast.significant nylon fishing line for a trimmer. Features of the STIHL FS 38 Motokos, adjust the carburetor of the Stihl FS 38 lawn mower. It is sometimes updated by the way of unwinding the coil, which is located.

How to reduce fuel consumption on a vase?

Surprisingly enough, but the fuel consumption on similar VAZ cars may vary. The scales are significant, one car can spend 25% fuel less, and this is a significant savings. As it turned out, the increase in consumption is associated with many factors, including the technical condition of the machine.

In order not to overpay for gasoline, it is often worth inspecting the condition of the tires, cleaning air and fuel filters, at times change the spark plugs. This is only part of the circumstances provoking overspending. In order to noticely lower costs you need to see others, and later remove them.

Sand spreaders

For example, Husqvarna 122c, which has a 0.8-liter two-stroke engine, consumes 630 g / kW / h. The fuel consumption of gas mowers STIHL FS 50 CE is 20 percent lower. In addition, he throws 70 percent less harmful emissions into the environment than models with a two.stroke engine.

The following are the tips that experts give users. They relate to the choice and use of the fuel mixture.

Experts advise buying mainly AI-92 gasoline for trimmers. To prepare a mixture with the correct ratio of oil and gasoline, it is necessary to maintain balance 1:30. Violation of this ratio leads to damage to the engine.

Store the mixture in containers that should be clean and safe. Since the fuel mixture sometimes settles, be sure to shake the spray can before refueling.

It makes no sense to pour more gas than you can spend. Then it is better to fill it than to clean the container.

MAIN! The lawn mower will last a long time and will save fuel economically for those who strictly comply with simple storage rules for the trimmer for grass.

The gasoline engine has a complex structure and therefore requires constant care. Therefore, before starting work, it is necessary to familiarize yourself with the rules of operation of the device and follow the recommendations developed by the manufacturer.

It is necessary to constantly monitor the purity of the inner surface of the body. In order to prevent corrosion of caustic grave juice in any part of the device, experts recommend cleaning the machine after the end of work.

Before buying a mower, it is necessary to determine where it will be stored. In this case, it is necessary to consider what sizes the device has. It makes sense to look at the model that folds the pen. In this case, he will find a place in any storage. That is, this option is simply great for storing the device.

Read Lawn Mushroom mowing stalls at high speeds

Setting up a carburetor of a lawn mower with three adjusting screws

Before starting work, you need to place the lawn mower on a flat stable surface. Remove the chain in the opposite direction. There are motorcycles with two and three adjusting screws. Two screws most often equip the tools produced in China. Consider the adjustment of the carburetor Motokos with three screws.

Setting up a carburetor of a lawn mower with three adjusting screws

Before proceeding with the adjustment of the carburetor of the lawn mower, you need to rinse the air filter. Cleaning is carried out with water with a detergent or soap, and if necessary, a new. Often in the poor work of the carburetor, scibberries are guilty. In order to prevent the filter, it is recommended to clean the filter after every 10 hours of operation of the tool. Do not forget to check the condition of the candle, if there is a dozen, you need to clean it. Candles are consumables and have their own resource. To ensure good operation of the engine of the lawn mower, candles periodically need to be changed. Next, we evaluate how well the carburetor is fixed to the cylinder-piston group. After the preparatory manipulations are completed, you need to start the motor. Let the engine work for 5-10 minutes. Then you need to identify how many adjusting screws on your tool.

There are the following adjusting screws on the gasoline trimmer:

Fuel supply adjustment

At first you need to slowly tighten the screw adjustment screw for the fuel mixture. You need to do this until the engine starts to stall or stalls. Following this, if the engine did not stop working, you need to turn the screw for a quarter of turnover, and if it stalled, then by half the turnover. Next, you should have a stalled engine. Then you need to open the throttle and see how the speed is gaining. Turn the screw for a quarter of turnover again. You need to scroll until the engine begins to confidently gain increased speeds during cuffing. This is the right time when the engine works most economically. There are times when adjusting this screw does not give anything. Often the reason is in the factory spring that is located on this screw. This does not happen to all the tools. And if the spring turned out to be defective, then replacing it will not be difficult. A suitable spring can be purchased at any construction store.

Cooper adjustment

Following the adjustment of the fuel supply, we are accepting for the adjustment of the idle. To do this, you need to adjust the corresponding screw so that the engine works slightly accelerated at small speeds. But it is necessary to trace, for the immobility of the reel with fishing line and knives. Before the start of their movement, several revolutions should remain in stock. The movement of the coil and knives can subsequently lead to the rapid wear of the clutch. Having noticed that the engine starts poorly, you need to increase the number of revolutions at idle. With an increase in revolutions, the fuel mixture is saturated with air, which leads to power loss.

The main signs of the proper idle work:

• Revolutions for a trimmer head;
• Uninterrupted operation of the engine even when the position changes (sharp rise or descent of the knife);
• Calm operation of the engine at a cold move;
• Lack of increased speed of hot engine.

Maximum speed adjustment

Further, for the full tuning of the carburetor of the lawn mower, it is necessary to adjust the maximum speed. It will not be superfluous to look into the instrument operating manual and see the maximum speed value. This amount will help to determine the tachometer most accurately. If such a device was not at hand, we set up by ear. Barely determining the maximum speed of revolutions by ear, we begin adjustment. A screw for limiting maximum revolutions will help in this matter. Control the engine operation at maximum speed. If necessary, reduce speed, weaken the fixing nut and unscrew the screw. If the turnover is too large, then you will need to screw the screw. These actions must be done in order to protect the engine from overheating. Scroll the screw until the clear even operation of the engine is established.

After the work done, if everything is done correctly, the stable work of the tool is provided.

Understand this by the following signs:

Several recommendations for choosing and using the fuel mixture

Gasoline braids and trimmers for grass are very convenient, compact and maneuverable, suitable for work in any cottage. They cope with grass in areas with different relief and different sizes. Their use in narrow, inaccessible places for lawn mowers is especially beneficial. In addition, they are cheaper and easier to maintain compared to the lawnical mower.

Did you know?Choosing which trimmer for grass is better. gasoline or electric, experienced gardeners are inclined to gasoline. Electric in many ways limits the movement (a certain length of the cord), needs uninterrupted power supply and is not very economically beneficial to use. But at the same time, the cost of the electrimmer is many times cheaper than gasoline, and it is ram.

We offer to familiarize yourself with the installation of bees trap

Before choosing a gasoline trimmer for grass, you need to at least briefly know the main parameters of the tool. The key when choosing a gasoline trimmer for grass will be how often you plan to use it and for processing which areas it is intended.

Based on this, the best gasoline trimmer for grass for specifically your site is selected by the power and performance of each individual model.

By type of suspension, trimmers for grass are stupid. the best option for infrequent use, and trimmers for grass with a backroot suspension. it is better to take such a constant, almost daily load on the tool.

According to the type of drive, gasoline trimmers for grass are with a straight shaft or a metal cable. It is better to take a tool with a direct shaft drive. they are more wear.resistant. By type of engine, benzotrimers are divided into two and four.

The former are refueling with oil already mixed with gasoline, the latter have separate compartments for oil and gasoline. Two.strokes are considered more noisy, and their service life is often less. And four.stroke. more durable, more expensive in maintenance and repair, but at the same time they work a little quieter.

The engine can be located in the upper or lower position. Located at the top is preferable. they are more convenient to operate, better cooled, more protected from clogging with grass and garbage hit, and they, as a rule, have more power.

A fishing line for a trimmer in configuration of a trimmer for grass is used only for mowing grass. By the type of pattern, several types of fishing line are distinguished:

• in the form of asterisk. for a green decorative lawn or young grass;
• in the shape of a square. for high grass with thick stems;
• In the form of a circle. a universal look suitable for both the lawn and for the obsessed and dry herbal stems, leaves.

For cutting branches, shrubs will need a knife. There are models equipped only with fishing line, but there are models with both fishing line and knives.

By the type of bar (handles), trimmers for grass are curved handle for low loads or with a straight line. for more loads. The weight of a trimmer for grass, as a rule, does not affect the work of the tool, it matters for a person working with him. if this is a man, then you can take a more heavier model, if a woman, then easier.

Before you choose a trimmer for grass for the lawn, study all the capabilities of each model. some of them are endowed with additional useful functions. This can be a snowmobile, the anti.vibration system. for the convenience of hands, the quick launch of a trimmer for grass with a decompression device that increases the life of the tool.

It should be noted that all improvements add value to the product. The most inexpensive are household trimmers for grass, and the most expensive are motorcycles.

Varieties

Currently, the Champion brand is available two main varieties of trimmers:

Electric models with a battery, unfortunately, are not produced by the company. All products are equipped with a coil of a proprietary cutting fishing line and a belt with a hip system. Consider the range of trimmers “Champion” Read more.

trimmer for grass gasoline Champion T 256 Two cords of spark plug as a gift!

Trimmer for grass gasoline Champion T 256. this light and practical model will cope with different types of vegetation and will achieve an excellent result when cutting lawns. The engine on the basis of which the device is assembled on.

trimmer for grass gasoline Champion T 333 Two cords of the spark plug as a gift!

Trimmer for grass gasoline Champion T 333. such a technique is created to optimize the process of haircuts of grass and reduce the time spent on work. The power of the engine on the basis of which the device was created is 1.25.

trimmer for grass gasoline Champion T 333-2 Two cords of spark plug as a gift as a gift!

Trimmer for grass gasoline Champion T 333-2 is an indispensable tool for ennoble the site in hard-to-reach places, in which the usual lawn mower cannot get due to its design features.

What will happen if you fill in the surgery in the chainsaw

If you do not want your chainsaw to refuse at the wrong time, use exclusively high-quality fuel and lubricants. Mixing with gasoline is prohibited. The reasons for this are the following factors:

• Another viscosity of the material, therefore, working out is not able to provide effective lubrication of rubbing parts and mechanisms
• The development contains small particles of metal and chips, which getting into the tank, will result in clogging the fuel filter and channel. If the lubricant enters the cylinder along with small particles, then they will leave their mark in the form of accelerated wear of piston rings
• Highlighting a large amount of black smoke, which indicates the combustion of oil

Surrogate materials cannot be poured not only in a tank with gasoline, but also in a tank for lubricating the chain. What will happen if you use working out in the tank for lubricating the chain, you can see on the video.

Using the instructions, you can independently prepare the correct fuel mixture on which the chainsaws will work. With improper dilution of the fuel mixture, not only the resource of the tool is reduced, but also its performance is reduced.

Publications

I served for a long time and did not deliver problems with the repair, you need to correctly prepare the fuel mixture. Internet forums are replete with questions on this topic. We interviewed experts and made a brief instruction.

To prepare the fuel mixture, use AI-92 or AI-95 gasoline. A lower octane number is not suitable. Gasoline is necessarily not ethyled (otherwise the engine will fail) and not old (octane number can change over time). It is forbidden to use oil for boats and four.stroke engines.

Mix gas and oil in a strictly defined proportion. Choose synthetic oil for two-stroke air cooling equipment API-TB or API-TC class. Do not save on ingredients. Ask in stores trademarks leading in quality. For example, Stihl, Husqvarna, Nanoeche, Champion, Alco, etc.

The main question is the proportion. Excess oil will lead to the formation of soot on pistons and candles. Excess gasoline will cause the appearance of bully on the pistons and an ambulance of engine. On average, one liter of gasoline is mixed with 20-50 ml of oil. Stihl and Husqvarna, for example, recommend taking 100 ml of oil for 4 liters of gasoline. The specified proportion is optimal for chainsaws up to 1.5 kW. For chainsaws with a capacity of more than 1.5 kW of the same brands, use a 1/50 proportion (100 ml of oil per 5 l of gasoline). Recommendations from Partner and Jonshed: 1/33 proportion (3.3 l of gasoline 100 ml of oil). Super synthetic oil is added at the rate of 100/1. These numbers are approximate. Always use the data given in the instructions for a specific chainsaw model. Trust the numbers indicated on the oil labels to the lesser extent.

What to mix? Kanisters with measuring divisions and two holes are presented on sale. for oil and gasoline. Pour the ingredients, tighten the lids and mix, tilting the container.

Many use glass and plastic bottles, children’s horns and syringes. Be careful with glass and plastic, be afraid of static electricity. Make sure that solid particles or drops of water do not get into the mixture. Be sure to thoroughly mix the mixture.

Ready fuel cannot be stored for more than 25-30 days, t.to. The process of oxidation changes its composition. Engine breakdown caused by overexposed fuel is recognized as non.warranty. The amount of the repair reaches 80% of the cost of the new chainsaw. After the end of the working season, use the remaining fuel, drown out the engine, remove the remaining fuel mixture.

Remember, your goal is to create a mixture that will ensure the uninterrupted operation of the engine, the complete combustion of fuel without the formation of soot, smoke or bullying.

Two.stroke engines, despite their imperfection relative to four.stroke structures, are still massively used on many newly produced devices.

Legendary Java with a two.stroke engine 638

• Basically, motors of this type are used for:
• Motorcycles of small cubot, snowmobiles, mopeds;
• lawn mowers, motor blocks, portable generators, chainsaws;
• motor boats;
• other devices where a small size is required with a high power.

The device of this engine imposes some features on operation. In particular, the usual lubrication system on most designs of two.stroke ICE is missing.

There are modifications where the lubricant is supplied directly to the flow of the fuel-air mixture from a special device in the form of oil fog. However, the vast majority of oil for modern 2-stroke engines enters the cylinders along with fuel.

Advantages and disadvantages of a gasoline trimmer for grass in the garden

The advantages include mobility, multifunctionality and instrument efficiency. Disadvantages are not always moderate price, especially in multifunctional mowers, and the noise of a working trimmer for grass, even in models with reduced noise.

But, on the other hand, the tool has good power, performance, and besides, a benzotrimer can work in any weather (after rain, for example).

That’s all, how to choose a trimmer for grass for a summer residence or at home. We wish to decide and choose that trimmer for the grass that is suitable for your site, lawn or garden!

You can advise the article to your friends!

You can advise the article to your friends!

Gasoline consumption rate for a lawn mower

In order for your lawn mower to serve for a long time and is economical in fuel consumption, we suggest that you familiarize yourself with several rules for storing this unit.

• The gasoline engine is a complex design that requires special attention and regular care. Therefore, before starting work, you must read the rules of operation of the machine and follow the recommendations of the manufacturer.
• Follow the purity of the inner surface of the body. The juice from the grass is very caustic, so after work do not be lazy and clean your technological assistant.
• When purchasing a mower, take care of the place of storage. Consider the dimensions of the unit and look at the model with a folding handle, which will be perfectly located in the storage.

Several recommendations for choosing and using the fuel mixture

According to your calculations.25 1 refueling 40 minutes or 38 hours 124 3.3 then the question suggests itself- how appropriate is it to have a saw T. However, in order to make these models cheaper and reduce their weight, the manufacturer sets not only small fuel tanks on them, but also engines, which in any case should be stopped.

Registration of an act of write.off for cars without a speedometer

Adjust so that the engine works confidently at low speeds and even a little accelerated for better start. But so that the coil with a fishing line or a knife does not rotate, and before the start of their rotation there was a sufficient supply of revolutions. To take into account the spent fuel only on the basis of vouchers cannot be prescribed in them such a business transaction as the write.off of expenses.

The spring may interfere

My first attempt to adjust the gas mowing carburetor did not give anything, since the spring of the fuel mixture adjustment propeller prevented. The factory spring turned out to be too thick in a compressed state and did not make it possible to reduce the supply of fuel to the required level. I had to choose another spring and continue the adjustment after its replacement.

The adjusting screw for feeding the fuel mixture with the spring

In the photo above the factory spring, below the adjusting screw with a selected spring. I am writing about this, because I am not sure that this is an isolated case, and someone else may face the same situation.

From personal experience

lawn mower or trimmer for grass

Trimmer for grass is a broader concept than a lawn mower (lawn mower), since it can also be an electric. The gasoline trimmer for grass and the lawn mower is the same thing.

Some authors assure that a trimmer for grass is a weaker tool, unlike a more powerful lawn mower, which can be used to mow shrubs. Personally, I have a tool with a maximum capacity of 1.7 kW and capable, as stated in the instructions, to mow a small shrub up to 10 mm thick. User manual is called “trimmer for gasoline grass”.

The proportion of the fuel mixture

I read somewhere that if the law mowing manual and the canister with butter indicates different proportions of the preparation of the fuel mixture, the proportion indicated in the manual should be used.

It was done for a long time. excess oil flowed out of the engine to the gas tank and the fiber was constantly formed on the candle, since the leadership indicated a proportion for a running.in engine 1:25, and on the canister. 1:50. After the transition to a proportion of 1:50, the appearance of oil fluxes stopped. The candle continued to burn, but with less intensity (the carburetor has not yet been adjusted).

Until now, some users of the benzo tool determine the fuel mixture “by eye”. If when preparing the mixture the amount of oil is underestimated, after a while an extraneous sound may appear immediately after the engine starts, gradually disappeared during heating, and the engine stop occurs with a sharp jerk. The continuation of the operation of a trimmer for grass in this mode will lead to its failure.

Clead cleaning

In the worst times of the work with a trimmer with an unresolved carburetor, the engine stopped starting after using each fuel tank. And only after cleaning the candle from the car, could you continue to work.

For cleaning the electrodes, fine sandpaper was used, and a thin stationery clip with a bent end was used to clean the space between the insulator and the case. At first, the electrodes were wiped with high dirt with a rag, then cleaned with sandpaper. After that, the candle fell into the diesel fuel and the moistened carpet was opposed by a paper clip from the surfaces of the insulator, the inside of the body and between them. Further, the candle fell several times into the diesel fuel, which then shake off it along with the pollution. Sometimes the procedure for cleaning a paper clip and washing were repeated. After that, the candle wiped dry and was ready for further operation.

Incredibly, one fuel mixture tank with an unresolved carburetor can be spent in less than 10 minutes. verified in practice, when the trimmer for the grass was launched and operated at high speeds with maximum fuel supply (the adjusting screw was unscrewed much more than the norm).

Online store AgroSemfond-seeds, planting material and other products for the garden and garden by mail from Nizhny Novgorod.