Winding the line onto the trimmer spool

Method 2. two segments

winding, line, onto, trimmer, spool

Two coiled line lengths

fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.

The end of each segment is folded

The end of each segment is folded.

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We start winding the line

They hook it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.

The bottom line is reeling

The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.

The tips are threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

Changing the line in the trimmer: 2 easy ways

A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.

In this manual, we’ll walk through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference lies in the fact that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing partition.

The line is inserted into the slot

The line is wound in the direction determined earlier. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does not change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end that section, which is located at the bottom of the coil, i.e. the one closest to the fixing holes.

This tip fits into the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes in the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes in the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing lines previously fixed in the holes of the reel jump out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to put it back on the trimmer and you can start mowing the grass.

It should be repeated, there is no need to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

Tips so that they do not hit the trimmer cover can and should be trimmed.

Preparing for replacement

We disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.

We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.

The spool consists of the following:

  • Spring case
  • Cover with locking latches
  • Button coil

The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.

Disassembled trimmer spool

On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.

These holes are needed to fix the line when replacing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.

Holes for fixing the line

There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for removing the fishing line from the trimmer spool body (see figure below).

Fitting on the holes of the line output

The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.

Two sections for fishing line

First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.

Determining the required line length

Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.

Special designation on the reel

If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Bobbin case designation

How to wind the line around the trimmer cutter head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

How to wind the line onto the trimmer spool

05 July 2018

The trimmer is a great solution for those who have a large garden or lawn near the house that needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutting element, you must first select it correctly. In principle, the operator’s manual for lawn mowers should indicate the diameter of the thread to be used in it.

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number of videos on the Internet that will help you figure out how to properly thread the line into the trimmer coil.

How to change the line on the trimmer

Below we have provided step-by-step instructions for replacing the trimmer thread.

The first thing to do is to unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done using a simple screwdriver and dropping it into the hole of the gearbox to prevent the shaft from turning. And then just unscrew

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may have to be turned in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it.

Second. After removing the mowing head, open it. This can be done by means of clamps that are located opposite each other. By pressing on them, you can remove the head cover, and then pull out the spool on which the line is wound. By pulling it out, you can determine what type it belongs to. There are one-piece and two-piece bobbins

We analyze how to thread the line into the trimmer spool in two versions

So, there is only one option. we load the line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of winding, do not forget to make sure that different ends of the thread are looking in different directions.

Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, according to the arrow indicated on the spool. Both segments should be wound so that they do not intersect. Further, the ends of the thread should be fixed in the grooves and divorced on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the spool in the trimmer, you need to gently hold the spring parallel while inserting the line into the slots on the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid.

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you watch the video on how to install a line on a reel in a trimmer.

How to remove the line from the trimmer reel

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. Not everyone knows how to do this. Our step-by-step instructions plus a video on how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

It is necessary to disassemble the mowing head

Remove the cover using the clips

We clean the remnants of cutting material

Hard ? Of course not. But if, nevertheless, doubts creep into you that for some reason you cannot do this, then of course find and watch the video how to pull out or how to wind the thread on the reel of lawn mowers.

How to replace the line on an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gas streamer, you get more freedom, since you are not limited by the cable that is present on the electric streamer.

Yes, do not hesitate to use the special videos on installing or threading the line in an electric scooter, which can teach you much faster than simple reading.

How does a line head work on a lawn mower why you need to know how it works

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

The principle of operation of the semi-automatic trimmer coil is as follows:

  • Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
  • A spring acts on the coil, which presses it against the slots in the cover structure
  • A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
  • During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
  • After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without adversely affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this moment that causes difficulties for most owners of special tools.

Trimmer head with two antennae

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Method 2. how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower’s line is the same as with the first method, and to make sure of this, below are detailed instructions:

  • There are two equal length pieces of material that you can use.
  • One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be secured
  • Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
  • The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
  • The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
  • Manipulations with the second end of the fishing line are carried out in the same way.
  • The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before threading it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

It is interesting! The tooling can be changed directly on the tool, but if you are doing this for the first time, it is still recommended to remove the head and study the detailed winding process. After the technology has been mastered, you can perform replacement work on a trimmer lawn mower or lawn mower.

The instruction on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
  • Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
  • The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
  • To unscrew it, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
  • After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but by slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
  • When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

How to properly wind the line on the trimmer reel with your own hands: we paint the essence

What line is used for the trimmer? How to remove the spool from the trimmer? Threading bobbins with different types of bobbins. A few tips for properly threading the string into the trimmer.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, flower beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer, exists in several variations:

  • petrol;
  • rechargeable;
  • electric.

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

  • Trimmer head with one working mustache;
  • A bobbin with two line antennae;
  • Auto winding reel.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

How to wind the line onto the trimmer spool

Winding Algorithm

Insert the resulting loop into the groove.

Lay the line in the direction indicated on the element body.

Insert the short end into the slot on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of coiled line into the spool body.

Pull the line out of the locking grooves.

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now all that remains is to screw the bobbin onto the trimmer and you can work.

How to choose a fishing line. length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him.

As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

How to properly wind the line on the trimmer reel. Step-by-step guide VIDEO

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cover according to the direction indicated on the body.

Remove the coil for winding.

Restring Spool for Black & Decker Trimmer / Edger

The preparatory stage has been passed. You can proceed to winding the fishing line.

ATTENTION! Typical line problems

No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem Cause Decision
Line break Stones, branches and solid objects in the grass Avoid collision
Poor cord quality Replace with a quality analogue
Head outlet wear Complete replacement of part required
The line is unwound The spring in the coil is weakened Check spring and replace if damaged
The line is sticking Poor line quality, due to which it can melt under the influence of temperature from the heating head Reel in less line or replace with a better line

For a better understanding of the mechanism of the process of changing the line in the spool with a video guide prepared by FUBAG specialists:

Winding the line on the trimmer reel. instructions

Using this or that tool or device, sooner or later you have to change some of its components, refuel, and so on.

For example, refueling a fishing tackle trimmer coil is quite simple, but there are some nuances that cannot be ignored. Here we need precise answers to the questions: how much and how?

How to remove the spool from the trimmer?

So that the assembly process is not long and tedious, it is best to put the elements of the untwisted mechanism in order. It will not allow you to get confused.

Here is the parsing procedure:

  • The clutch nut is unscrewed.
  • Next, you need to untwist all the small washers and gears.
  • Need to remove the handle.
  • Need to disassemble the spool mechanism.
  • The rotor is removed
  • Now the line guide roller is disassembled.
  • Next, the coil is removed.

What line is used for the trimmer?

One of the types of fishing line is used to refuel the reel:. Mono-line. It is a versatile single-thread fishing thread. The composition includes plastic compounds, polyethylene and everything like that.

Whole factories are engaged in the manufacture of monofilament, each time trying to make the fishing line as effective as possible, “able” to create the most approximate game of bait to live. Wicker. Two types of braids can be distinguished here: classic and braided cord in a sheath.

How to wind line on a trimmer spool (video for beginners)

Instructions on how to wind the line on the trimmer spool

Here are the steps for winding a monofilament fishing thread onto the trimmer spool:

  • The end of the line from the reel is pulled into the pass rings of the finished tackle.
  • Open line guide.
  • Using any fishing knot, tie one end of the monofilament to the bobbin.
  • Perform a few turns by hand by moving the spool “wheel”.
  • Now winding can be done with the handle.
  • When the winding is done, you need to close the line guide.
In another method, a reel with fishing line should be thrown over a stick so that the reel rotates freely around its axis. Next, wind it around the trimmer bobbin. Here it will not be very convenient to wind up alone, it is better to resort to the help of a friend.

As for winding the braid, then you need to do the following:

  • Dip the prepared reel with a braid into a container of warm water, or at least into the water of a river or lake, right on the spot.
  • Now you need to wind up. Due to the more or less softened fiber, the line will lie down and wrap quite smoothly and tightly.

Threading the spools with thread of different types of bobbins

It should be noted that there are several types of fishing tackle reels:

  • Inertial;
  • Inertia-free;
  • Multiplier.

Each type of non-inertia reel has its own fishing line diameter. If the thread is thicker, it will not be possible to thread it into the spool. Difficulties will also arise if, for example, a too thin monofilament is used, which is not intended for threading a particular spool.

In the case of threading a non-inertia spool, one of two well-known methods is used:. “cross-to-cross”;. parallel winding, that is, thread after thread lies parallel to each other.

Now about the multiplier bobbins. Multiplier spools are subspecies of inertial ones. Many fishermen make the same mistake, they tie the end of the string to the farthest hole of this element. It is wrong to do this, it is worth tying only for closely spaced holes.

Filling the baitcasting reel with fishing thread follows the following scheme:

  • First monofilament is fixed to the body of the spool.
  • Next, you need to attach the coil to the spinning rod and pass the free end of the scaffold through the right ring.
  • Tighten the device that protects the tackle from jerking fish.
  • Tighten axle brake.
  • Now you can wind up by guiding the line and thus controlling it.

Tips from experienced fishermen

Here’s what professional fishermen advise:

  • Don’t wind too much line. This suggests that if the permissible winding length is 100 meters, then in this case you need to wind a little less. This will allow the device to work more correctly.
  • When winding, the string should not be too tight or, conversely, weakened. And in that, in another case, it will not lie as it should. It can twist, go to the side, overlap, and so on. Conical layers of fishing line can also form, that is, thickenings on one side or another.
  • Winding should be carried out before reaching the upper edge of the coil, about 1-2 mm, this distance may increase slightly.
  • If the line is dropped periodically during winding, then you need to take a little more than the previous distance from the side wall of the spool to the line being wound. You need to increase literally by 0.5 mm.
  • Fast winding of the line will not ensure its good distribution over the surface of the spool. On the contrary, it can “twist” so that it will be difficult to fix it. The best option is average speed.

There are also devices that allow you to attach the reel directly to the rod. This allows you to wind the line, firstly, without outside help, and secondly, the refueling process is greatly simplified.

Method 2. how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower’s line is the same as with the first method, and to make sure of this, below are detailed instructions:

  • There are two equal length pieces of material that you can use.
  • One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be secured
  • Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
  • The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
  • The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
  • Manipulations with the second end of the fishing line are carried out in the same way.
  • The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

Method 1. how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out how much line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is level with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the equipment into the trimmer or lawn mowers is as follows:

  • To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
  • After that, take the second end from the other side, and fold it in half. Move to it so that the measured protrusion of 15 cm is preserved
  • There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
  • Next, we find out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. It should indicate the direction of winding (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
  • This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE”, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the fishing line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  • Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
  • When almost all the fishing line is wound on a reel, you will need to do the following. place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then similarly do the procedure with the other end, placing it in the hole on the parallel side
  • We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
  • We put the drum in place and, pulling the ends of the line, disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
  • At this point, the process of how to replace the fishing line on the trimmer is completed, and if necessary, you can only trim the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is also a second way, how to charge the mowing equipment in the lawn mower. What is the difference, and how is the second method of threading the line on the reel of lawn mowers carried out, we will find out in detail.

What you need to know about trimmer line

A fishing line is a consumable made of nylon that serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its use on the corresponding tools, low-power electric (from 1 to 1.6 mm), electric from 500 W (2 to 2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3. 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and reload the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel.

Step-by-step instructions on how to wind the trimmer reel and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

Learning to properly wind the line on the trimmer reel and lawn mowers installation instructions

Private home owners know how essential a trimmer tool is. It can be gasoline and electric, and they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before threading it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

The instruction on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
  • Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
  • The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
  • To unscrew it, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
  • After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but by slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
  • When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
  • If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
  • When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
  • If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
  • There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction of the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

How does a line head work on a lawn mower why you need to know how it works

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

The principle of operation of the semi-automatic trimmer coil is as follows:

  • Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
  • A spring acts on the coil, which presses it against the slots in the cover structure
  • A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
  • During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
  • After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without adversely affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this moment that causes difficulties for most owners of special tools.

Tips and tricks on how to wind the line and what you need to know

There are some useful tips and tricks that will be useful to learn not only for beginners, but also for experienced mowers. These tips will help prevent negative consequences in the form of injury and malfunctioning of the mechanism. These guidelines read as follows:

  • It is necessary to install the cover until it clicks. over, this is 2 or more clicks, which depends on the number of latches. If one of the latch does not snap into place, the drum may jump out when starting the tool and injure a person.
  • Do not reel in the line with a strong pull, or more than you can insert it into place. It is better not to wind up the rig than there will be more of it, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
  • If you own a tool not with two line leads, but with one (usually these are low-power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of a middle rim between the extreme bases of the coil
  • After replacing the material, it is necessary to first check the operability of the tool, and after that start mowing the grass. If you do not make a preliminary check, then the scaffolding can unwind and injure a person.

The result of the work done is as follows. after the replacement of the new material, the usual one is enough for an area of ​​up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials last less, which is important to consider when working. Do not try to cut thick-stemmed grass with fishing line, as there are special metal discs or knives for this.