DDA lawn mower does not develop momentum. Checking filters

Trimmer for grass Energomash is not gaining momentum

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass. If the filter is clogged, you can try to rinse it

If this procedure has not brought the effect, replace it with a new

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

What to do if the engine does not start?

If the lawn mower fails is not possible, then the first thing is to check the presence of fuel in the tank and its quality. For refueling the tool, it is recommended to use high-quality gasoline purchased at gas stations, the brand of which should not be lower than the AI-92. Savings on cheap fuel can lead to a breakdown of the cylinder-piston group, for the repair of which a third of the cost of Motokosa itself can take

It is equally important and correctly preparing a fuel mixture of gasoline and oil. The proportional ratio of these components of the mixture is indicated by the manufacturer in the manual

Do not prepare the fuel mixture in large volumes, since during long storage its properties are lost. It is better to use a freshly prepared mixture.

When preparing the fuel mixture, pour the oil into gasoline using a medical syringe that allows you to accurately comply with the necessary proportion of the components

Fuel filter pollution in the tank may also prevent the operation of the lawn mower engine. Therefore, when problems with the launch of the motor, check the condition of the filter. If necessary, replace the filter. It is forbidden to leave the incoming pipe without a fuel filter.

The air filter also needs to be in the test. During contamination, the part is removed, in the field is washed in gasoline and put in place. In the country or at home, the filter can be washed in water using detergents. After that, the filter rinses, squeezes and dries. The dried filter is moistened with a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with hands. Then the part is installed in place. The removed cover is placed back and fixed with screws.

The air filter washed in the fuel mixture, squeezed and dried, is installed in place in the plastic case and covered with a lid

How this procedure is done in more detail you can look at

If all of the above procedures are carried out, and the engine is not started, then adjust its revolutions at idle, twisting the carburetor screw

In the video posted at the beginning of the article, attention is paid to this issue

• Put the tool on the side so that the air filter is at the top. With this location of the chainsaw, the fuel mixture is ensured exactly into the bottom of the carburetor. On the first attempt, the engine will start if you remove the air filter before starting and pour a few drops of the mixture into the carburetor, and then install the dismantled parts to the place. The method is tested in practice.
• If the first advice does not give a result, then, most likely, the problem in the spark plug. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not show signs of life, replace the new.
• If the spark plug is in good condition, the filters are clean and fuel mixture, then you can use the universal way of starting the engine. Close the carburetor air damper and pull the starter handle once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will surely start.

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

Features of the work of a trimmer for grass

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

• turn on the ignition button;
• press the silicone button for pumping gasoline several times;
• close the air damper;
• The gas lever is installed in a position for high speeds;
• first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

Trimmer malfunctions for grass

Trimmer for grass is a convenient and affordable replacement for the lawnical mower. Its cutting part is made in the form of fishing line, knives or disk installed on the drum, which is closed on top of the protective casing. The basis of the design is a bar, which is adjustable in height, at the end there is a comfortable handle and shoulder belt.

Like any other technique, a trimmer for grass may be unknown, and so that the breakdown does not lead to the final failure of the tool, we suggest you familiarize yourself with this article. Unit can break down for various reasons. Breakage occurs both in new trimmers and those that have long been operated.

A malfunction of electrical models

The reasons for the unexpected shutdown of an electric lawn mower are associated with a cliff of the cord or the absence of current. In the first case, it is recommended to check the cable for a cliff. To replace the power cord, you need to pull out the fork out of the outlet, open and dismantle the circuit lid.

Before unscrewing the squeezing of the cable? It is necessary to remember the diagram of its connection to the switch. To disconnect the cord, a hexagon is used (diameter 1 mm). The clip is released, the conductors are dismantled. To check the cable for a cliff, multimeter is used. If necessary, a new cord is installed. In this case, the reverse sequence is observed.

In the second case, it is recommended to connect another device to the mains. Electric devices may not work when the fuse is damaged in the fork. To carry out repair work, you will need to disassemble the fork. For this, a screwdriver and a tester are used.

Motor malfunctions occur when overheating of the lawn mower:

In the first case, it is recommended to wait a few minutes so that the motor cools. In the second case, you need to remove the stuck object. The effectiveness of the cooling system depends on the state of the air filter.

Dirty device poorly passes air, which helps to turn off the device. Experts advise cleaning and changing the filter once every 3 months (with constant operation of the lawn mower).

With a breakdown of the electric motor, the corresponding smell and noise appear. In this case, you need to replace the drive.

The vibration of the motor on idle, on a cold or warm engine: possible causes

Immediately note that there are many reasons for the emergence of vibration of the internal combustion engine, starting from the torn engine pillows (supports) and ending with ignition passes and the tag of power unit. For a more accurate definition, first of all, you should pay attention to one or other symptoms.

The fact is that vibration can be either constant (regardless of heating and loads on the unit), and manifest itself in a certain mode of operation (idle or high speeds, on cold or hot). Another engine vibration can manifest itself on a cold ICE, but as it warms up, it completely disappears. Let’s understand.

• For example, if the engine was recently versed for repair (possibly capital), then there is a high probability that the crankshaft was not properly covered after the reverse assembly. The result is a beating and increased vibrations.
• We also note that after repairing the motor to imbalance and vibrations, different weights can lead to the details of the cylinder-piston group. The more weight difference turns out, the stronger the vibrations will be. For this reason, experienced craftsmen weigh pistons, fingers, etc.D.
• Often the reason for vibrations is that the engine is troit, that is, one or more cylinders for any reason do not work or work with failures. As a rule, the elimination of the cause of the touch automatically eliminates the presence of vibrations of the power plant.
• Do not forget that the timing belt incorrectly set on the marks or the chain also causes vibrations.The reason is that the engine works unstable due to violation of the phases of gas distribution.
• Many engines have in their design special balancing shafts that are necessary in order to “extinguish” fluctuations. Quite obvious, problems with these shafts will lead to an increase in the vibrations of the motor.

The engine pillows are one of the most common reasons why the engine vibrates. In fact, this is a damper made on many cars from rubber to absorb vibrations. As you know, over time, the rubber daggers and cracks, loses its properties as a result of technical fluids and t.D. The main thing is that the engine with a damaged pillow cannot work softly.

• If you recently moved from one car to another, it should be borne in mind that different engines may differ in vibration loads. The number of cylinders, layout and a number of other features affect the level of vibrations. In simple words, the usual in-line engine for 6 cylinders can operate with less vibrations than a 4-cylinder and, especially, 3-cylinder engine. over, in this case, we are not talking about problems, since for a particular ICE a certain level of vibration can be considered the norm.
• We also add to reduce vibrations, on the crankshaft of many engines there is the so.called dignified damp. If problems arise with the element, the motor will begin to vibrate more strongly.

As you can see, at the initial stage it is important to accurately determine the cause of the strengthening of vibrations. For example, in most cases, it is enough to replace the engine support or solve the problem on which the engine is troit. However, it also happens that the power unit itself needs to be disassembled and repaired.

Repair of mechanical braids is carried out when the cutting elements are blown up or damaged. In this case, experts recommend to independently dismantle removable knives. Evadal is used to sharpen them. If necessary, the battery is replaced in battery.

Before repairing the lawn mower, the type of motor is determined:

The lawn mower stalls at high engine speeds

During operation, a situation arises when, when pressing the fuel supply key, the aggregate turnover begin not to increase, but to decrease. A malfunction of this nature can be caused:

Fuel hoses Motokos with filter

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

Features of the work of a trimmer for grass

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

• turn on the ignition button;
• press the silicone button for pumping gasoline several times;
• close the air damper;
• The gas lever is installed in a position for high speeds;
• first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

Why is a benzotrimer not gaining momentum and strangle

A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops. The device itself is a rather difficult mechanism, because there are many different circumstances of its breakdowns. As a rule, the emerging problems contain an annotation for operation. Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.

Problems with a benzocosa associated with the purpose that this device is not started, specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:

In order to correctly find the knot where the breakdown occurred, you need to study in what circumstances the trimmer stalls for the grass.

If the lawn mower stops when pressing the gas, then the prerequisites are usually subsequent.

• The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.
• The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
• The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.

Reasons why the lawn mower does not develop momentum

There are five main reasons why the trimmer for STIHL grass does not develop turns:

Low quality fuel use

Benzotrimmer does not gain momentum in case of low quality fuel. He may stall or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for problems with the combustion chamber.

In the presence of sediment, plaque formed on the candles, the old fuel is drained and flooded another, high.quality.

It must be remembered that a trimmer for grass or a lawn mower should be refueling good quality gasoline and those fuel brands that the manufacturer indicated in the technical passport of the device.

Note! Candles should be thoroughly cleaned of plaque, and only after that place again in the combustion chamber of fuel.

Air or fuel filter pollution

There is a lawn mower does not gain speed, the reasons may be polluted by the filter element: air or fuel.

When blocking the air filter, there is a lack of oxygen in the combustion chamber, so the fuel is not fully produced, which prevents the desired speed and power.

To check if the cause is really in the air filter, you need to remove it and turn it on. If the lawn mower still does not gain momentum, the reasons are not in it. So you should check the fuel filter element. Everything is similar here, only gasoline acts as oxygen. If this filter is damaged, there will be a lack of fuel, which inhibits the development of revolutions.

In one and another case, the output is simple: you just need to replace the filter. If there is a spare, to install it, if not, to purchase in any specialized store, is inexpensive.

Problems with ignition candles

When a benzotrimer is used often, you need to monitor the state. This part is susceptible to wear, so we need to regularly inspect: if there is a fuck on them.

You can solve the problem in two ways: clean the old candle from Gary or purchase a new one.

In the first case, you need to unscrew and swing with sandpaper, dry. The distance between the electrodes should be 1 mm. Trimmer for grass is collected and advanced.

In the absence of a spark between the electrodes, it is worth inspecting the quality of the connections of all the elements of the circuit. If in this case everything is fine, then 100% you need to change the candles.

Replacing them is easy and inexpensive. From the tools will be needed a key, supervisor.

Important! With frequent appearance of soot on the candlelights, it is worth looking for a reason a little deeper. Candles should be carefully cleaned of plaque

Candles should be carefully cleaned of plaque

Problems with the engine

Engine problems. already more serious. There are several options for a malfunction:

In the case of the problem of the carburetor, you should first pay attention to the condition of the cable. It can be weakened, which led to a problem

A simple adjustment of the cable is required here.

If this did not help, then you need to check the use parameters. These operating standards can be found in the technical passport of the device. Sometimes it’s enough to disassemble the device: to wash and collect and assemble.

note! The solution to the problem with the carburetor may be the purchase of a new element or by contacting the service for professional services. The trimmer drive is subjected to a full check only if the manipulations with the carburetor were not given the proper result

The trimmer drive is subjected to a full check only if the manipulations with the carburetor were not given the proper result.

FLOOK DISCOUNSE

The lack of fuel circulation in the system can also be the reason why the device does not gain momentum. There are several options for why this is happening:

You can eliminate problems yourself. For this you need:

• remove blockages from the gasoline pump;
• update hoses, pipes for fuel circulation;
• Clean the muffler and mesh on it;
• Reinching a new catalyst.

Do not worry when such problems arise. This does not mean at all that the unit of poor quality. If the Patriot trimmer does not gain momentum, it can be repaired with your own hands without contacting the service.

If everything is in order with electrical equipment, then we check the carburetor.

Vacuum carburetors are put on trimmers for grass. When disassembling it, cleaning or washing, it is necessary to be as careful as possible under any circumstances to disassemble the lower part of the carburetor where the primer is located. Air filter (it is visible if you remove the protective casing from the carburetor) must be washed with detergents. The most ideal for washing dishes. After drying, put back. We wash the carburetor with unsented gasoline and blow out all the holes by the pump. We also wash the filter of the gas pipeline, then we dry everything and collect everything. Usually, after all manipulations, the trimmer for the grass begins to work.

A narrow cable is made of fishing line, it is worth placing it on a motorcycle?

This idea comes to mind in virtually everyone who had to pump out 10 acres overgrown with the highest grass. On the 1st gaze thought seems good. The cable is stronger than the fishing line, it is not so wear out. But not everything is so simple.

Also, the ignition coil can be broken in electric equipment. In this case, the lawn mower will not start or start and works with interruptions, and later stalls, or it will not start on the hot at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark when the starter is jerking, or it occurs after once you need to change the coil.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

will stall at idle. At speed stalls a trimmer for Champion grass. Hoodluck lawn mower four thousand three hundred stalls at speeds. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

Air or fuel filter pollution

The next common cause of reducing the number of revolutions on the trimmer is the pollution of its air or fuel filters. In the first case, the problem is that the fuel-air mixture entering the combustion chamber is not saturated with oxygen, as a result, gasoline does not burn out all. This does not allow the maximum power to develop a motorcycle.

In order to check whether the air filter is really to blame, you need to remove it (first promoting the lid for this) and turn on the lawn mower. If it works fine, then instead of a clogged filter element, you must insert a new.

Read how to lubricate a gearbox of a gasoline trimmer for grass

If the situation has not changed after the actions done, then you need to pay attention to the fuel filter. The essence of the problem is similar to the previous case, only instead of a lack of oxygen is a little gasoline for the normal operation of the device

The elimination of this problem is also carried out by a simple replacement of the filter element. Air and fuel filters are inexpensive. It is easy to change them on their own, and all the work does not take much time.

It should be borne in mind that without a fuel filter, it is forbidden to operate a trimmer for grass, otherwise you will need to repair a piston node after a short time.

Diagnosis and elimination of electric motor problems

Electrimmer malfunctions can be as follows:

To cope with these breakdowns, you do not need to disassemble the entire device.

On a note! Before you start repairs, it is important to prepare the necessary tool: a set of screwdrivers, a tester, a soldering iron, indicator, a set of keys.

With serious engine failures, you will have to disassemble it. To do this, you need to unscrew a few screws. Having gained access to the motor details, you need to carry out the following actions:

• Checking the degree of wear of brushes. unsuitable details will need to be replaced with new ones;
• Rall the engine winding. the resistance should be high;
• Check the stator and rotor. to test the rotor winding with a multimeter, measure the resistance: large deviations from the norm indicate a malfunction, the absence of resistance on the stator winding also indicates a breakdown (the same way is diagnosed with the stator case).

Advice! The solution to problems associated with faulty electric nodes are associated with great difficulties. Often it is easier to replace them with new details than to take time for rewinds.

Low.speed problems are a common phenomenon for cheap trimmers. However, with improper maintenance, such manual mowers as Huter, Patriot 3055, Echo also suffer from this.

When to contact the workshop

If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.

Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

• low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
• The grass was wound on the shaft of the fishing/knife head;
• clogging of the air filter/muffler;
• Balance of the carburetor.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply

The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when Clotting of the valve

, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop may also be called Air suction

In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

Why does the engine are poorly gaining momentum

During the operation of the gasoline or diesel engine, the driver may encounter the fact that when the gas is pressed, the engine does not gain speed. Note that after installing the equipment on a liquefied gas on a car, such a problem often appears when the gas engine does not gain speed, although the car works normally on gasoline. Different species malfunctions can be wrapped in both fairly ordinary things, and indicate the need for harsh repair of a gasoline engine. Then we will see, why The diesel engine does not gain momentum or the internal combustion engine renounces spinning.

We check the electrical equipment as follows:

We unscrew the candle, examine the gap between the electrodes. We set the right gap between the electrodes can be a “grandfather” way. We take a blade from a razor, scraps in half and insert a home.made probe between the electrodes. If the blades enter tightly, then the gap is perfect.

We put on a candle cap of a high.voltage wire and lean the candle against the metal surface of the engine. Twist several times by the starter. If the spark beats well at one point, then the gap is adjusted correctly. If not, the spark is weak or “wanders”, then it is necessary to re.adjust the gap between the electrodes.

Other malfunctions of chainsaws

A lot of users are faced with trouble when the chainsaw does not throw off the moment. The device in a matter of seconds reaches maximum power, which cannot be reduced.

• The throttle does not function. its spring or an element of traction weakened;
• The switching tumbler is poorly switched;
• The shaft of the throttle.

But there may be the opposite situation. when I drank uncontrollably gaining power. The reasons why the chainsaw herself is gaining momentum, you need to look for in:

• carburetor. it must be cleaned or reconfigured;
• fueling system. a gasophiller, fuel hose;
• malfunctions of cylindrical piston or pipes connecting them to the carburetor.

Breakdowns that manifest themselves through a momentum atypical for a particular part of the working cycle, quite a lot. But an attentive attitude to the tool will help to diagnose them in time and return it to normal work.

The lawn mower stalls hot? There is a solution!

The lawn mower stalls hot-this means that there is already a certain amount of fuel for starting the engine, but after 5-10 minutes of operation, it stops working in the engine. This motor behavior indicates problems with the fuel filter.

This article will solve the case of a gas station when they stall at large gas speeds

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “Lawn mowl

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

gaining momentum. very frequent inconsistency and of course always has a common solution.In this.

Features of the work of a trimmer for grass

All trimmers for grass are classified according to the type of power: gasoline or electricity (electric network or battery). It must be emphasized that gasoline mowers in almost everything prevail their electronic and battery colleagues. Although they all make similar functions, differences in performance, dexterity and effectiveness are very noticeable. But the general mechanism of the work of all types of manual braids is practically the same as devices equipped with engines (two- or four-stroke internal combustion engines or electric motor), which drive the cutting installation (reel from the fishing line or iron disk). All elements are fixed on a straight or curved strip, including a trimmer handle for grass, on which the main buttons are placed.

Since the inconsistent of low revolutions is more often found with gasoline variations of the finish, they will pay more attention. So, the shield is very comfortable to use and is undemanding in maintenance. over, most of his defects are caused by the ignorance of the user of simple things, which are written in the instructions. Therefore, before starting the operation of the device, you should closely study the management of the manufacturer. Namely, to start the motor, you need to perform subsequent steps:

• turn on the ignition button;
• Press the silicone button a couple of times to pump gasoline;
• close the air damper;
• set the lever of the throttle in the position of the highest speed;
• At first, make light jerks with a starter handle to feel the resistance of the motor, then sharply with a jump.

If the brush starts, but hung, it is necessary to put the air damper in the middle position and experience it again. When the engine starts to work, you need to slow down the gas and open the air damper for you, since the trimmer for the grass only works at the entrance.

Fundamentally! From how the trimmer for the grass works, depending on different influences of the environment. In hot weather, the device should give more time to cool down. When working in dense thickets or with the highest vegetation, the engine also overheats. Make five-minute breaks every 15-20 minutes.