How to assemble a cultivator for a single tractor. Independent installation of milling on one -axle tractor

How to assemble a cultivator for a single.based video tractor

If you choose the right mill, you can not buy a plow. When milling, it is very easy to control the cultivator, there is no large load on the operator. Mills are selected for the cultivator depending on the power of the technique and the type of soil soil.

Three main types of soil are distinguished:

• Factory. They are equipped with most machines. They are collected and disassembled. Axis with welded plates and attached saber.shaped knives. Two or three identical sections are connected by bolts. The width of cultivation depends on their number. Factory cutters will cope with pre.treated areas;
• Goose legs. The design is non.devastated. the number of sections is selected for itself. With the help of such milling soils are processed, plant residues are interrupted. Reduced load on the gearbox. The cultivator is easy to control. The “Goose legs” milling cutters are great for equipment with air cooling system;
• Virgin lands. The milling cutter is perfect for processing virgin lands, plowing the soil at a great depth, loosening the soil. The design is reliable and durable.

Often the factory cutter is not enough. To increase productivity, reduce the load on the equipment and saving time, it is worth buying “goose legs”. For severe development of virgin lands, soil cutters of “virgin lands” are more suitable.

Not so long ago, mills began to be used for motoblocks, which were called “goose paws”. They have proven themselves well, are most often used to process solid and complex soils. It is such cutters that are used when cultivation should be carried out in difficult conditions, on rocky soils. The design of the “goose legs” is made continuous, which provides the highest indicators of the strength of the equipment. Mills are available in standard sizes:

• knives width is 41 cm;
• The length of the knives is 38 cm;
• structure height. 38 cm;
• The mass of the cutter is 16 kg;
• The permissible operating speed of a motor cultivator with such knives is 2-5 km/h.

What are the pluses of the “Goose legs” cutters, is it possible to install it on your own? It is convenient for soil processing, weed fighting. The remaining models will not be able to cope with work better. For rocky and solid soils, the “Goose legs” cutters are simply indispensable. Of the advantages, it should be noted that the steel of cutters in this case is welded. If necessary, you can carry out repairs at home, and not buy new knives, as it is costly.

Read also: thermal conductivity of aluminum and brass

The cutter of this type also has disadvantages. The main drawback is that ordinary carbon steel is used for manufacturing. The strength of the design itself is at a high level, but the material loses a little other varieties. Such a milling cutter should be regularly inspected when work is carried out on clay soils, with the cultivation of virgin lands. Knizes knives can be curved or simply broken. However, the repair is not too complicated, a welding machine is usually used for a broken knife, after which the fracture is thoroughly polished.

When assembling the circuit, you should work together, since the weight of the design is significant. It is important not to confuse the direction of installation of knives on the axis. When assembling, sharpening should look towards the processed soil. To strengthen the cutter, use a lock, it is placed on the output axis.

Motoblock cutter diagram and device

Thanks to the saber.shaped form, the cutters for the walk.behind tractor are safe in operation. If the one.axine tractor ran into the root or stone, the cutters lift it like the wheel of the car, while continuing to continue processing. If the cutters are straight, then they can catch on an obstacle and overturn the one.axle tractor. The consequence may be the loss of equilibrium by the operator and a possible fall into cutters.

Knives are attached to the plates that are welded to the shafts at different angles. Thanks to this, cutters enter the soil smoothly, in turn. This favorably affects the transmission of the walk.behind tractor. Carbon steel is used for the manufacture of knives. If there is access to the forge using the springs, you can make such knives. For the manufacture of other parts, the following steel brands are used: ST-25, ST-20, ST-10, which are easy to welcome to welding.

The principle of the cultivator and its main advantages

Cultivator for a walk.behind tractor. an agricultural unit for loosening, moisture conservation, soil hilling without turning the upper layer.

Types of cultivators

Among the cultivators, the following types are distinguished:

For the Neva motornote, the basic package includes 6-8 phrases-cultivators with a diameter of 360 mm and a capture width of 1200 mm.

Device

The same.based tractor from the cultivator is largely weighty and the presence of a power shaft. The cultivator is equipped only with milling cutters, and any attached and trailed equipment that corresponds to the characteristics of the equipment is aggregated to the walk.behind tractor.

Different engines are installed on cultivators-2-, 4-stroke gasoline, diesel and electric, operating from the network or built-in batteries. They are compact, but in terms of power are inferior to motors built into motoblocks.

How to make a cultivator for a walk.behind tractor

Before the manufacture of the cultivator to the walk.behind tractor with your own hands, it is necessary to treat all metal elements with a special anti.corrosion composition from premature appearance of rust after frequent contact with the ground.

Simple models can be performed without drawings. To make and correctly collect more complex devices, you need to plan the work, calculate the dimensions of the module and parts.

Homemade cultivator from a fork is a simple way to re.cross (alteration) products. For this, the teeth of the mechanism with a hammer are bent by the type of corkscrew and planted on the handle. As a handle, a stalk from a shovel is used. For fastening, use island.

Some masters manage to make a cultivator with their own hands from a bicycle frame with a wheel. Between 2 blocks of the base is welded or fastened with bolts of a steel rod. The head is mounted to the cross. For this design, it is recommended to take a medium.sized wheel.

In order to correctly assemble a disk cultivator and work correctly with cutters, it is necessary to design the diagrams of the nodes and individual details. Given the deformation of the discs, special regulatory nuts are used. Disks are welded to the bushings located on a rotating axis with brackets. On the bracket it is necessary to provide a ledge where the pipe will take place. The cultivator handle is attached to the pipe surface.

Do.it.yourself cultivator knives

For the manufacture of knives for a cultivator with your own hands, you need to take alloy steel with a thickness of 0.5-0.8 cm. The triangular shape of the knives with a pointed angle is optimal in terms of effectiveness. The width of the knives should be selected within 5-9 cm. Too bulky knives create increased resistance, due to which they often break.

As cutting elements, you can use knives from a segment mower, which before installation on the cutter must be hardened. This option of knives is not suitable for processing virgin grounds.

DIY Cultivator mills: Goose legs

Before starting manufacture, you need to familiarize yourself with the drawings, calculate the number of segments and the total weight of the structure so as not to load a low.power unit. On a cutta mill for a cultivator in one segment, it is best to install 3 “paws” at 3 “.

Making cutters for a cultivator type of goose legs with your own hands consists of the following stages:

• First you need to make an axis with flanges. As an axis, you can take a steel pipe with a section diameter of 2.5-3 cm. The flanges for attaching the “legs” are made of steel plates 5 mm thick, holes are drilled for fasteners, and welded to the axial pipe.
• Make triangular knives (see. in the previous section) and racks. For racks, it is best to take metal strips of the same steel brand. The rib that will be in contact with the soil during operation, you can sharpen. A knife is welded to one end of the rack, and holes for fastening are drilled in the other.
• Further, the obtained “paws” are connected to flanges using bolts or rivets. The milling cutter is ready, you can carry out the first run.in installation.

Active cutter for a walk.behind tractor with your own hands

Before starting the manufacture of an active cutter for a walk.behind tractor with your own hands, you need to decide on the type and study the drawings of the most suitable structure for a specific soil.

If there are figures in the selected design, they can be ordered from a turner, the rest of the elements can be made independently.

Consider the features of the manufacture of active (saber.shaped) cutters for the walk.behind tractor. The dimensions of the working elements should be no more than 50 cm, which allows them to deepen 25 cm into the ground. this is enough for effective plowing. The width of the tool can be selected based on the distance between the rows on the site, the weight and power of the walk.behind tract.

• steel pipe with a diameter of 4-5 cm;
• springs from a car or strip of alloy steel for future knives at the rate of 3 blades per segment;
• welding machine;
• corner grinder;

The manufacturing process consists of the following stages:

• To make lobed knives, strips of steel or sprinkles must be made the same in length, heat and bend each on one side by 90 °, the length of the bent part should be 60-80 mm.
• To weld the knives to the pipe, placing them segmented, 4 knives from different sides of the axis. If you want to make a prefabricated design, make an axis with flanges similarly to an analogue previously considered.
• Sharpen the blades from the side where they enter the ground. Sharpically sharpen the diamond circle, the angle of sharpening is 45 °, it must be strictly observed.
• Install a ready.made active mill to the cultivator, test and adjust.

How to assemble mills on a single tractor correctly?

The assembly of the cutter can cause some difficulties, especially if you do this for the first time and alone.

First you should familiarize yourself with the structure of the cutter.

The drawing below indicates its main components:

• rotary axis (there are different lengths, can be solid and detachable);
• finger with a latch;
• knives (right and left);
• structural elements (nuts, washers and bolts).

Also do not forget to take into account the fact that the movement of the knives during operation is directed counterclockwise. Be careful when assembling the module. any deviation in the design will lead to the fact that the balancing of the axis will be violated, the unit will be entered during operation.

We also offer to familiarize yourself with the video that describes in detail about the process of assembling milling to the walk.behind tractor:

Description and principle of operation of the plane cutter

Flat cutter, proof, Cultivator. all these are the names of the same tool. A patent on a manual plane cut was issued in 1995 in.AT. Fokin. Older Gardeners remember the disputes that immediately erupted between the supporters of the deep cultivation of the earth with a plow and a small. flat cutter.

The novelty of the tool consisted in the corners of the bending of the blade and its double.faced sharpening, which provided shallow, but high.quality soil processing. This approach often turned out to be more effective than plowing, digging with a shovel or cultivation with cutters.

• Rimbage of beds and personal plots. The blade cuts the roots of the plants, after which the weeds die, and their aboveground part reprises and fertilizes the soil.
• Formation of the ridges and grooves for sowing, as well as the formation and sealing of holes.
• The cultivation of unprocessed, virgin or highly detonated soils. Cleazing cutters with such dense soils often can not cope (with the exception of saber), the plow stucks on the rhizomes of shrubs and weeds. And the plane cutter successfully cuts the sod, at the same time cutting the roots of meadow herbs. After that, you can once again pass the virgin land with a plow or milling cutters for optimal processing.
• Processing of wet and heavy soils. For example, soil lumps and crust formed after heavy rain are perfectly destroyed.

Flat cutter helps to process and loosen the soil

Processing with a flat cutter scares off pests living in the soil (moles, mice), prepares the ground for planting, saturates the upper soil layer with oxygen.

Initially, manual plane cutter was developed for gardeners with poor health and disabilities. Installed on a single tractor, it is very effective in processing virgin lands, the cultivation of the soil, the destruction of weeds. The working part has an accurately verified angle of sharpening, providing the desired mode of operation.

Hedgehogs for weeding

Inter.row processing is carried out by a special looser, which is called a hedgehog. The device is made in the form of several metal rings with different radius. They are located at a short distance from each other, forming together a semblance of a cone.

On each segment there are sharp spikes that are designed to tear out weeds. To increase efficiency, the structure is made paired, but asymmetric. Parts are located at an angle to each other.

• Weed weeding. The spikes catch plants and pull them out of the soil with the roots, while not touching the culture.
• Loosening and swelling of the soil. The process improves the penetration of air and moisture into the soil.
• Formation of rows. The landing structure looks neat.

Hedgehogs are used both for weeding potatoes and for hilling. They are suitable for all types of soil and areas.

The device works on the principle of rotational harrow. The spikes penetrate the ground, and the rings rotate, due to which the plant is pulled out and loosened soil.

Types of milling plants for Neva

First of all, the question arises before buying cutters, and what are they actually they are? Now the most popular two types of mills:

They have their differences in purpose and form. Let’s dwell on more on what their differences are?

Sable.shaped mills

This type is considered a standard option for cultivation. Sable cutters successfully passed the test of time, and proved their effectiveness.

It should be noted that in the standard configuration with the Neva walk.behind tractor, this type of milling is going on.

Raw materials in the manufacture of saber.shaped mills. high.quality steel with high carcade. This metal itself is very durable. But to achieve even better metal density, it is additionally stabbed and undergoing electric shock at high frequencies. Thanks to this, the final product is strong and reliable.

Sable.shaped milling mills. Because this steel is not susceptible to welding. Therefore, all compounds occur using bolts.

This is how the cultivation of the Neva with saber.shaped mills occurs:

Frases to the walk.behind walkway “Goose paws”

This model has recently gained its popularity and is applied along with the “Sable.shaped cutters”. It is mainly used in the cultivation of more solid soils.

A distinctive feature is that this milling cutter is solid, not collapsible. This gives her additional strength and allows you to work with virgin lands and successfully fight a lot of weeds.

In its standard form, it has the following dimensions:

With such dimensions, the weight of such a plow is about 16 kg. And the maximum soil processing speed is 5 km/h.

The disadvantage is the material from which “goose legs” are made. This is ordinary carbon steel of which the density is not large. And it often breaks or bends when working with increased loads. But on the other hand, with such strength, the plow is easily welded and further repairs.

This is how the cultivation of the Neva by the “Goose legs” cutters occurs:

Protective disk on cutter

To ensure the safety of operation at the end of the cutter, a protective disk must be installed.

Thanks to it, you can clearly adjust the area of ​​the processed surface and prevent the accidental cultivation of plants or flowers in the garden, or other crops.

Assembly instructions

It is easy to install the cutter on a single tractor, but for this you will have to pre.assemble it by organizing the direction of rotation: the sharpened part should crash into the soil.

Fastening is performed on the axis of the output shaft. For fixation, a stopper requires. It is quite difficult to perform installation actions with your own hands alone. It is best to use x-shaped goats made of wood. As a rule, they are made about 50 cm high.

The same-based tractor must be lean on the snufftor, then tilted somewhere to the level of forty-five degrees, substitute a goat under the handle of the steering wheel. Further “Technique”: just take off the wheel.

Before starting the assembly of the milling cutter, you should think over its design, as well as those functions that it should perform. To do this, it is important to view similar products using information in details. Otherwise, the product will not perform the work that is necessary. So, the actions will turn out to be meaningless.

First you need to make at least an approximate drawing, one of these is depicted in the photo. Based on this, all the necessary components are selected. And then you need to act according to the drawing, in stages collecting every detail. When the assembly of the cutter for the walk.behind tractor is performed, it is necessary to test. This will immediately make adjustments to its design, if the result will deviate somewhat from the alleged.

additional information

It should be noted that the procedure is quite understandable, but for clarity, the assembly of the cutter cutter on the video is also presented. This will allow more thoroughly to understand the procedure, take all steps correctly. Then you get a worthy product and an addition for a walk.behind tractor that allows you to cultivate the soil especially productively and efficiently. So, the result of such actions with your own hands will be achieved.

Assembly instructions

It is easy to install the cutter on a single tractor, but for this you will have to pre.assemble it by organizing the direction of rotation: the sharpened part should crash into the soil.

Fastening is performed on the axis of the output shaft. For fixation, a stopper requires. It is quite difficult to perform installation actions with your own hands alone. It is best to use x-shaped goats made of wood. As a rule, they are made about 50 cm high.

The same-based tractor must be lean on the snufftor, then tilted somewhere to the level of forty-five degrees, substitute a goat under the handle of the steering wheel. Further “Technique”: just take off the wheel.

Before starting the assembly of the milling cutter, you should think over its design, as well as those functions that it should perform. To do this, it is important to view similar products using information in details. Otherwise, the product will not perform the work that is necessary. So, the actions will turn out to be meaningless.

First you need to make at least an approximate drawing, one of these is depicted in the photo. Based on this, all the necessary components are selected. And then you need to act according to the drawing, in stages collecting every detail. When the assembly of the cutter for the walk.behind tractor is performed, it is necessary to test. This will immediately make adjustments to its design, if the result will deviate somewhat from the alleged.

additional information

It should be noted that the procedure is quite understandable, but for clarity, the assembly of the cutter cutter on the video is also presented. This will allow more thoroughly to understand the procedure, take all steps correctly. Then you get a worthy product and an addition for a walk.behind tractor that allows you to cultivate the soil especially productively and efficiently. So, the result of such actions with your own hands will be achieved.

Cultivator cutter assembly process

Sharpened. “Petals” easily enter the soil without adhesion to the surface. Thus, the load on the motor decreases and the consumption of fuel mixtures is reduced. But with sharp blades you can not completely remove weeds, soon they germinate again

With such canopies you need to work carefully so as not to damage the plants for your own safety;

With a semicircular edge. Differ in safety during operation

But when loosening, there is a greater resistance, soilofors are more often stuck. With weeds, such knives for the cultivator do more effectively.

To collect the cutter to the motor.cultivator, it is important to observe the direction. the sharpened part of the “petal” must be placed in the course of the movement of the machine. The number of sections is equal to fixing plates: with their same location, only three elements are possible to install

If they shift, four to six sections should be attached. Knives need to be previously labeled

The number of sections is equal to fixing plates: with their same location, only three elements are possible to install. If they shift, four to six sections should be attached. Knives need to be previously labeled.

How to make cutters for a walk.behind tractor with your own hands

The cutters are not difficult. Before collecting them, you should familiarize yourself with existing details and their constructive features.

Materials that will be needed

Before assembly, you should measure the site that you plan to process, and on the basis of the data obtained, start collecting a mechanism. To get the most correct design will be needed:

• welding machine,
• Corner grinder,
• details that will play the role of baking powers;
• Long metal tube with a diameter of 42 mm.

The basis for looser can be automobile springs that bend and weld to the main pipe at an angle.

Tips regarding manufacture

First of all, pay attention to the correct assembly. Avoid any deviations, even the most insignificant

If you show inattention, then the axis will be broken

Installing home.made cutters for a walk.behind tractor and cutters for a cultivator, it is important not to confuse the direction of rotation of the teeth

Sable.shaped knives are less dangerous in comparison with another. With them the danger of getting serious injury is minimal. Alternate location of the knives makes their entry into the ground consistent, there are no blows and jerks.

In order to extend the life of home.made devices as much as possible, it is necessary to adhere to several simple rules, in particular, when the frizes are launched, there should be revolutions after that, the blades are slowly lowered into the soil. this is how the processing begins.

Assembly process

As already mentioned, work begins with the measurements of the site. After all the calculations are made, you can proceed directly to the assembly. Using a welding machine, connect knives with a pre.prepared pipe. Before that, you can sharpen the edges of the elements at the right angle.

People who have experience working with metals will be able to collect mills for the Neva motornote. Pre.compiled schemes, as well as a set of high.quality tools and materials allow you to simplify the installation.

To assemble a mechanism such as a milling cutter for a walk.behind tractor, you can also familiarize yourself with recommendations and steadily adhere to the sequence in the work. Then the device will serve for decades.

Information about the engine of the walk.behind tractor

The power part, the transmission and the supporting frame are collected as follows for them.

• The engine for a walk.behind tractor must have forced air cooling: this is a necessary condition at a low speed of movement. The power unit from Motoroller “Ant” is great: it works on gasoline and has a capacity of 13 horsepower.
• The gearbox is connected to the engine. The muffler will have to make it independently from a steel pipe with a diameter of 70 mm. It is necessary to cut off 250 mm from it and fill with metal chips and sawdust. The configuration should be such that the exhaust gases are assigned to the side and do not interfere with the work. The exhaust hole is narrowed to 16 mm.
• The engine for the engine is made of a steel pipe with a diameter of 42 mm in the form. At the edges and in the center are fastened by welding of the bracket with holes for m8 bolts. Then this frame is located in the central bracket down and welded to the central cross member of the slide. For a better connection, welding, sections of the pipe of the salads and metal metal must be slightly bend: this will increase the area of ​​touch.
• The device of the motor block involves mounting the engine to the frame at the points indicated on the drawing. The determining factor in the development of the design of the slide and the frame are the size of the power unit.
• In the center of the vertical shelf of the traverse attached to the guides, it is necessary to send a hole with a diameter of 10 mm. This is required to install the M10 bolt, with which the chain will be pulled from the first stage of the gearbox.
• The undercutal frame is fixed by the Bolts M10 to the main frame at four points. Salads move along the spars along four grooves (two in each skose of a hoodie).

What types of milling plants are installed on motoblocks

The motor block can be treated with any type of soil, perform different types of work. aeration, loosening of soil or crushing with a lump, removing the roots of perennial weeds, mixing soil layers or fertilizers. The functions and capabilities of garden technology directly depend on the type of installed milling plants. spring, hook, flat looser, etc. Three types of attachments are considered the most versatile, demanded and functional:

• Sable.shaped. Active type of cutter for a walk.behind tract that requires assembly. They are installed on most models of garden equipment. Frases can consist of 2-5 sections with knives that determine the width of cultivation. It is made of steel, provides an optimal depth of loosening of soft and unspecified soil. Plant roots are not wound.

• Goose legs. Inactive type of milling with non.vegetable design. Designed for the processing of solid, rocky and trampled soils. The cutting blades interrupt the remaining plants in the soil, remove the roots of perennial weeds, and promotes aeration. The foot of the knife can have the shape of a shoulder blade, triangle or trapezoid.

• Spiral, or “virgin lands”. Inactive type of whole milling cutter. It is designed for deep plowing soil, virgin treatment, loosening. The design is reliable, but the processing speed is reduced. Consists of 2-4 sections.

The owner of the new garden technology will need a detailed instruction to collect cutters for a saber.shaped motor.cultivator, since 9 out of 10 models are supplied with disassembled attachment equipment. Two other types of milling plants are required only to hang.

The need and the rules of sharpening during operation

When working a walk.behind tractor, the working surface of the knife will inevitably wear out. To restore the cutting ability of the tool, it must be periodically tightened. The timing of the procedure is purely individual. The speed of wear of the knife depends on such moments:

• the intensity of the use of the motor block;
• firmness of the processed soil;
• the presence of plant roots or stones in the ground;
• The strength of the material of the knives.

Manufacturers of agricultural equipment supply mills already with sharp blades. Therefore, when buying a walk.behind tractor, it does not make sense to drag knives. However, the procedures cannot be avoided with intensive operation of the unit. To restore the sharpness of the knife, an angular grinding machine (angular grinding or “corner grinder”), a sharpening or diameter of 12.5 cm with a diameter of 12.5 cm, will be required.

To tighten the working edges at an angle of 45 °. Remove the layer of metal from the side of factory pointing. At the same time, do not get too carried away: just hide 1-2 mm. During the season, you may need to restore the cutting ability of the cutter several times, and excessive removal of the metal reduces the strength of the knife.

When using a cutter in wet soil, it is necessary to carefully clean the surface of the blades. During friction on the ground, the surface of the metal is cleaned of an oxide film and becomes chemically active. This process is accompanied by enhanced corrosion, which entails the formation of ospins, chips, microcracks. To prevent such phenomena, the blades should be treated with special inhibitors or car oil.

How to work as a motor.cultivator: step.by.step instructions

Before plowing the cultivator, be sure to conduct a preparatory event described above. After, for plowing:

• Motor cultivator is being started.
• Let the engine work 0.5. 2 minutes., to warm it slightly and disperse the oil through the engine knots.
• The handle of gas is placed approximately half.
• They start work.

During the processing of large areas, the cultivator engine cannot be overheated. When a specific smell appears, a change in the sound and nature of the engine operation, the work with the cultivator stops and it is time to cool down the engine. But it is better to do this before these signs of overheating.

How long the engine can work before a pause depends on the model, on whether the engine is driven or not, at what revolutions processing is underway, what is the weather on the street.

Often our readers send us the following question. is it possible to plow with a motor block on rubber wheels? We answer, if you mean plowing with a plow, then theoretically it is possible, but not worth it, for this purpose it is better to use metal wheels, it is easier to plow with them and faster. Rubber will slip.

Safety precautions during work

Let’s talk about how to use the cultivator correctly, in general it is a relatively safe technique. Injuries and harm to health can only be obtained for four reasons:

• emission of stones from under the cutter at high speeds;
• injury of any part of the body when it enters rotating cutters;
• burn on the hot parts of the engine, muffler;
• Poisoning with exhaust gases during the processing of closed greenhouses.

To protect against the ejection of stones, you can not remove a protective shield, a casing or wings, which are on almost all motor cultivators. In the photo, a model on which a red protective shield is clearly visible.

Cultivator cutters are located quite far from the legs of the operator. To avoid injuries, you can categorically approach rotating cutters. Before you remove the grass, inspect mills and t.D., You should drown out the engine.

Engine units that are very heated during operation, as a rule, are marked with special warning signs. Even if there is no such marking, it should be remembered that first of all it is a muffler, which is very heated from hot exhaust gases.

Exhaust gases from combustion of gasoline or diesel fuel are very toxic. Therefore, you can not work in closed greenhouses, as well as leave it in the garage in preparation for work.

All doors and the provided ventilation windows must be opened. If there is forced ventilation, it should be turned on. But even in such conditions, working with ICE in closed rooms is not recommended for a long time.

You can find out more about how to plow a motor.cultivator correctly in the next video.

To plow the earth with a cultivator on time, as soon as the right weather is established. Do not postpone the work for later, since then there can be any weather surprises. When servicing the unit, first of all, you need to pay attention to the quantity and quality of oil. You should not save on the quality of the oil, it takes a little, but it depends on it how long it will work properly the engine engine.