The Patriot T 535 Rro petrol trimmer is used for mowing young tender grass on lawns, for cutting down weed with a fragile thick stem, a young shrub with thin branches, willow and reed thickets. The model was developed in the United States and is licensed in China. A distinctive feature of this tool is low cost, ease of use.
Characteristics of the lightweight Patriot T 535 Rro trimmer
- A modern gasoline trimmer for mowing grass and mowing grass with an optimal cost and normal productivity.
- Built-in anti-vibration blanking system adds comfort to use.
- The balanced design allows you to perform a large amount of work without undue effort on the part of the operator.
- Belts anatomically fit the figure and do not interfere with a sharp change in movement.
- Air-cooled two-stroke gasoline engine.
- The increased motor resource.
- Quick start due to electronic ignition primer.
- Mobile, easy operation. No experience with a similar tool is required to perform basic operations.
- A gas trigger is located on the ergonomic non-folding handle of a bicycle type, which allows you to adjust the engine speed during operation, quickly switch from one object to another.
- The gas lock is located on the handle in the reach of the fingers.
- The shaft for the trimmer is rigid, which ensures reliable fixation and stability of the working head.
- The bar is not collapsible.
- Air filter with an affordable and simple device, lightweight and easy maintenance.
- Interchangeable cutting tools expand the functionality of the trimmer.
- The handle is adjustable and finely tuned to fit the operator.
Technical parameters of the Patriot T 535 Pro model
- Four-stroke petrol engine with electronic ignition.
- Rotational speed 9000 rpm.
- The engine tank volume is 0.33 l.
- Engine power 1.8 hp
- The bar is straight, non-separable.
- Maximum / minimum cutting width 460/230 mm.
- Replaceable cutting line / knife cutting equipment. Diameter 2.4 / 230 mm.
- Net 7 kg.
- Gross 9.7 kg.
Video: How To Dress A Belt From A Patriot Trimmer
Self-assembly of the Patriot T 535 Pro trimmer
The design of the tool is simple, without complex parts. Self-assembly is available to any user without technical knowledge and design assembly experience.
- There is a mount on the main bar. The handle is installed in it so that the open part is on the right side.
- The handle is bolted, but not completely tightened.
- The control knob is set with the trigger of gas to the trimmer head.
- The fastening screw is tightened stationary and securely.
- The control cable clips are fixed to the handle in their respective slots.
- The shoulder belt carabiner snaps into place on the main rod mount.
- Go to the assembly of the lower part of the rod.
- First, an iron casing is attached to protect the gear housing, and a plastic protection is covered on top.
- A protective flange is mounted on the splined shaft of the gearbox. The coincidence of the technical grooves of the gearbox and flange is observed.
- A rod or hexagon is inserted for fixing into the technological hole between the gearbox and the flange.
- The trimmer head is screwed against the stop counterclockwise.
The trimmer cannot be operated without the installed protective flange. If the flange is not installed, after finishing work it will be impossible to remove the trimmer head.
- The iron casing is screwed onto the base of the gearbox.
- A protective flange is installed on the splined shaft of the gearbox, the coincidence of the grooves is observed.
- A knife is mounted on the protective flange.
- A clamping washer is placed on top of the knife and tightened with a nut against the stop counterclockwise.
- A fixing rod is inserted into the hole between the flange and the gearbox. The coupling nut is tightened with a ring spanner.
- A safety pin is inserted on the gearbox shaft.
Do not sharpen a dull cutting knife. The edge finishes and the balancing of the instrument goes astray. The shaft is jammed. You can turn the knife over with the sharp side and continue working, and then at the end of the process, change the knife to a new one.
- The fixing lever of the fastening system is squeezed out, the parts of the rod are connected so that the fixing of the fixing lever fits into the guide groove of the lower rod.
- With proper assembly, the bar cannot be opened without pressing the latch. If easy disconnection occurs, reassemble.
- The additional fastening of the coupling is tightened to the stop.
- Regardless of the job, it remains possible to rotate the lower bar at angles of 90 and 180 degrees with the lower bar firmly fixed.
- Put on a trimmer. Adjust the anatomical belt to your size. Adjust the length of the trimmer handle.
- Tighten the bolts holding the handle all the way.
- Pour the fuel mixture into the tank and start working.