How to hold a trimmer for grass with kosb. High grass

How to adjust the motorcycle to the back so that the back and hands do not hurt

The lawn mower, no doubt, is a more productive tool for work than a regular manual. In addition, motokos is now sold with electric drive. It is not very convenient to be attached by a cord, but even this option is better than manual. There is only one problem. and benzo-. and the electric cosmos weigh five times more than their manual analogue, and in the process of work the back and hands receive a large load both from weight and vibration. So the operator in this case still gets tired, and it is difficult to work with such a weight for a long time. But in fact, fatigue and muscle pain is not so much from the weight of the instrument as from its incorrect position. If you adjust the braid, then the load will be distributed evenly, and it will be much easier for you.

Starting a conversation is perhaps with the question of choosing a model. If you are embarrassed in funds and are looking for something cheaper, then keep in mind: cheap Chinese models are very difficult to adjust, in addition, they are made for the Chinese, that is, small people. With our average growth, you will lack both the length of the bar and the length of the pens.

The second important point is the equipment. And again, cheap models in losing: many of them have no oblique belts, no gloves and glasses. Special belts can be bought separately, there are even special satchels that are very conveniently adjusted to the owner.

How to adjust the fasteners on a motorcycle

Pay attention to where the hook is on the fasteners when you put it on. It should be 15 cm below the middle of the thigh and be located strictly horizontally. Suspension braids for grass are carried out between the engine and the handles. For balancing, use the bar and loop.

The height of the planting of braids for grass also depends on your task. If you need to shave the lawn at the height as close as possible to the ground. the working part should be lowered if it is necessary to cut off thick thickets. raise.

Take your shoulders and evaluate the position of the straps. They should not crash into the shoulders or television freely.

To correctly adjust the handle, try not to raise or put pressure on them. They are needed only to turn the tool to the left and right, and the bar would go freely, and the hilt did not hit the leg.

We start with safety precautions

From the protective devices, glasses and gloves recommended according to the instructions will not interfere with the instructions, but the most important protection of the legs. Cutting tool, especially if mowed with a gasoline trimmer with metal knives, rotating with huge revolutions, picks up garbage, pebbles and cutting of vegetation, flying away at such a speed that they can cause injuries to a person. Therefore, it is desirable to work in trousers and closed shoes or boots.

As for the protection of the ears, the tangible need arises for this only for the most “loud” benzotrimmer. based on a two.stroke engine. They are usually equipped with special headphones with the headline necessary to reduce sound pressure on the eardrum.

Preparation of a trimmer for grass for work

Preparation of a trimmer for grass for work begins with checking the condition of all parts and assembly according to the instructions. At the same time, you need to make sure that there is a lubricant in the gearbox, and in the crankcase of a four.stroke gasoline trimmer for grass there is enough oil. Fuel, depending on what type of engine, two- or four-stroke, is a mixture of gasoline with special oil in a ratio of 40–50: 1 or, accordingly, pure gasoline. After the fuel tank is filled, it remains only to open the tap and the trimmer for the grass can be tried, not forgetting that before the start of the kosba, it is necessary to work at idle for 2-3 minutes.

With an electric battery tool, everything is simple. after checking the availability of lubricant, it is enough to insert a charged battery into the corresponding nest so that it is ready to work. If the tool is powered by a power grid, then you will need an extension cord to the expected haircut location. The wire must be placed outside the zone of the possible action of the trimmer knives for the grass.

The site should be maximally freed from foreign objects: glass, stones, wires, snags, etc. D. The presence of people is closer than 15 meters is also undesirable. Depending on the capabilities of a particular trimmer for grass and expected work, you need to select the appropriate cutting nozzle. You can use a mowing head with a fishing line for grass, metal knives for weeds or hay harvesting or a shrub saw. Powder should be planned to move, moving away from buildings and people.

A trimmer device for gasoline grass

Today there is a wide variety of benzos on the market. But, despite this, they all have a similar device and work almost one, and the same principle.

An internal combustion engine located in the upper part of the tool includes the device of each gasolimmer. Depending on the device, a 2- or 4-stroke ICE may include a motorcycle equipment. A translucent plastic fuel tank is located next to the engine, as well as a starter responsible for manual launch of the motor.

Motors are connected to the cutting organs using a metal rod, inside which a flexible or hard drive shaft can be installed. As a rule, manual benzo.codes are equipped with indifferent rods, but sometimes manufacturers equip their equipment with collapsible rods for more convenient storage and transportation of tools.

Almost all the benzo-codes are equipped with handles that can have a D-shaped shape, or resemble a bicycle steering wheel with their appearance. On one of the handles of the handle there are controls that are associated with the drive of the motorcycles using a cable. There is a gearbox in the lower part of the gas station, the main function of which is to transfer the effort from the shaft to a standard spindle equipped with cutting organs. To protect the operator from damage, each gasoline braid for grass is equipped with a plastic shield, which is attached at the bottom of the bar.

As cutting organs of a gasoline trimmer for the grass is a fishing line for a trimmer placed in a plastic coil, or a metal disk. As a rule, the head and discs are complete with a garden tool. Thanks to this, the operator always has the opportunity to install the cutting device that will help to mow wild vegetation without overloading the motor motorcycles.

and more men are replaced by scissors, a razor, barbershop and professional hairdressers for home trimmers for grass. And this is understandable. a trimmer for hair grass is relatively inexpensive, it is intended for personal use, therefore, it is more safe than its salon analogues, it is convenient, small, universal and always at hand.

Many mistakenly suggest that a trimmer for grass is the same hair cutter, only with a modern foreign name. However, the function of the device is not only to cut, but also to trim the hair, which can be considered a big advantage of the device. A trimmer for grass is a device for haircuts and trimming hair, which is equipped with a kind of scissors and a razor.

Hair grass trimmers

Before you purchase the device, firstly, to understand for the hair of which part of the body it is intended, and secondly, what characteristics in the priority of the future owner.

The design and fundamental scheme of the work of trimmers are very simple, but the tool is quite effective.

The trimmer for the grass looks like this. an engine and a cutting mechanism are connected to a long metal rod. They can be located at opposite ends (motor from above, spindle from below) or group on one. lower (engine over the working tool). Inside the bar (this hollow tube) is a flexible or hard shaft, which transfers a rotational impulse from the motor to the cutting mechanism. This can be done in three ways:

• Direct rods use a rigid design. rotation is transmitted to the gearbox through the sequence of closed parts, and then to the spindle of the working head.
• Flexible shafts in the form of a cable are used in curved tubes.
• With the lower location of the engine, the transmission mechanism is not needed, in this case, torque comes from the shaft of the motor to the spindle directly.

Rush and pen

The bar can be of collapsible or sliding (telescopic). Around the middle of the tube there is a handle for holding the device on which control elements are placed: start/stop buttons (at electric models), gas adjustment lever and a stopper for fixing the key responsible for the flow of fuel (for gasoline devices).

Belt system

Often there is a metal loop on the rod, to which the shoulder belt of the adjustable length is attached. The belt helps to reduce the load on the hands, which facilitates prolonged work and reduces the likelihood of injuries and pain in muscles and joints due to strain.

Working head

The working head of the trimmer for the grass is partially covered with a protective casing, in order to prevent the cutting nozzle from contacting the wiretracks or obstacles in the form of large plants, fences and buildings around which you need to push the grass. On a spindle can be worn: a coil (bobbin) with a fishing line, a metal disk/strong plastic with sharp teeth or nozzles for special needs (chain saw, knife, garbage harvest and others). The cord is wound on a bobbin with a stock with a margin or inserted chopped pieces. In the first case, the fishing line for the trimmer can be pulled to the desired length as worn out.

The principle of operation of the type of garden tool in question looks like this-when the engine turns on, its shaft begins to rotate, and the movement is transmitted by the spindle with a coil or nozzle, worn on it (the cutting tool is attached using a bolt). Head speed. from 3,000 to 12,000 revolutions per minute.

Pros and cons of an electric trimmer for grass

This device for work in the garden and on the site has a lot of advantages:

• Electric lawn mower trimmer for grass is multifunctionality and is able to solve a variety of problems.
• Simplicity in operation and repair. It is easy to figure out in the uncomplicated design and, if necessary, replace the new part of the new one, since all the necessary components are in free sale.
• High efficiency.
• Surriety of an electric trimmer for grass. Such a device will not interfere with the neighbors and will not cause their anger.
• Environmental friendliness. Unlike its gasoline counterparts, this tool does not pollute the environment.
• Binding to the mains. The device does not tolerate voltage drops and is limited in movement. The exception is the tools working from the battery.
• Small power. The “more neglected” the site, the less often the owner visits his cottage, the more powerful he needs the tool. If he combines it with a lawn mower and uses only for cutting along the fence and paths, then a light model with slight power is quite enough for him to complete the task.
• The inability to use an electric trimmer for grass on even areas. It’s all about the different heights of mowing grass, which negatively affects aesthetic attractiveness. In addition, the cut vegetation has to be collected with your own hands.

Which is better an electric or gasoline trimmer for grass?

Everyone solves this issue for himself. Gasoline braids are highly performance and power. They hardly and quickly process the surface, making it possible unhindered movement around the site, because in this case a person is “not attached” to an electric cord. However, the lawn mowers vibrate and make noise very much, pollute the air with exhaust gases, which creates obstacles for their use next to growing vegetables and fruits. In addition, they are much more expensive than their counterparts.

Working from the network, mowers are compact and easy. It is much easier to wield in hard.to.reach places. Electric trimmers for grass for giving are cheaper than their gasoline analogues, and the lineup is incredibly wide, which provides the opportunity to choose a tool for yourself and your needs, given the individual characteristics and specifics of the landscape.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

During the mowing of grass (and turns), do not forget to look around!:

• To notice the gesticulation of others, drown out the motor and remove the headphones,
• So that closer than 15 m children, animals, spectators and assistants do not come up, t.to. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg. Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. the thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). or less gas. only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

• Grass density;
• The hardness of the grass;
• the splendor of the grass;
• wovenness of grass;
• (The height and thickness of the grass are not important)
• the boundaries of the site;
• what irregularities (how to come in);
• the presence of hidden obstacles (remember)
• that not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

Work in raw weather

If there is a need to mow a trimmer in any weather, then it definitely should be gasoline, since it tolerates raw weather well. Although, according to the instructions, work in the rain or on wet grass by some manufacturers of such gasoline equipment is also prohibited. When choosing a trimmer for grass for this, it is also worth paying attention to.

Electric motor. the most vulnerable to moisture place in battery trimmers. Accordingly, if it is located on top, then there is less likelihood of moisture from the grass, but in rainy weather they also cannot work.

The most sensitive to moisture trimmers for grass with power from the mains.

Typically, with wet grass, water enters the extension cords, where an electric arc can occur that can ignite the insulating plastic or cause a short circuit. Such a defect is “corrected” by buying a new extension cord or replacing a fork, but moisture entering the engine or control circuit leads to an irreversible exit of the trimmer for the grass. In addition, working with such a tool in the rain is simply dangerous, since there is a high probability of electric shock.

Electrimmers

Electric trimmer for grass. a good country option. In this category, two types of trimmers can be distinguished: network, battery. In terms of power, they are inferior to gasoline, but suitable for mowing a small household territory, cleaning paths, flower beds.

Network models are more productive and powerful. With their help, you can mow grass for several hours. At the same time, make sure that the device does not overheat, take breaks. The only drawback of a trimmer for grass is attachment to electricity.

Battery trimmers for grass

Battery models are light, comfortable. Suitable for women, older people, adolescents. Power and charge are enough for work in the personal territory. The main disadvantage is the battery life: it is enough for 30-90 minutes of mowing. Charging takes several hours.

Electric trimmers for the grass do not pollute the environment, do not emit much noise, easy to maintain, do a great job of performing the tasks, are an excellent addition to the main lawnapers, can work in hard.to.reach places.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

During the mowing of grass (and turns), do not forget to look around!:

• To notice the gesticulation of others, drown out the motor and remove the headphones,
• So that closer than 15 m children, animals, spectators and assistants do not come up, t.to. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg.Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. the thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). or less gas. only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

• Grass density;
• The hardness of the grass;
• the splendor of the grass;
• wovenness of grass;
• (The height and thickness of the grass are not important)
• the boundaries of the site;
• what irregularities (how to come in);
• the presence of hidden obstacles (remember)
• that not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

How to use a trimmer

Tips on how to mow grass

• Mowing grass when it is not very large. This will allow you to cope with work much easier and faster than if you mow a strongly overgrown lawn or yard. A large mass of grass, weeds, plants and trimmer will be hard to grind. In addition, a lot of chopped grass will lie on the surface, which must either be cleaned, or wait until it dries, or while it becomes compost, which is not very beautiful and can cause various diseases of the grass.
• Avoid mowing not grass, but fences, stones, bricks, any other hard objects, as this will greatly accelerate the wear of the fishing line and it will require its more common replacement.
• Some will have to wear an orthopedic corset (although it may seem stupid). Back support allows you to maintain performance longer and feel more comfortable.

Warning how to use a trimmer

Trimmer for grass, like a twin.franc grinder, chainsaw or garden tractor is unreasonable for what it is not intended for.

Keep a trimmer for the grass away from yourself so as not to cut off your fingers or leg.

Do not mow a trimmer in water or wet grass. If you have an electric trimmer for grass, you may hit an electric shock. If you have a gasoline trimmer for grass, you can pollute water and grass with fuel and exhaust gases.

You will need things to mow grass

• Pants. Preferably strong working jeans without holes. You can mow grass somewhere, so if your legs are not protected, soon you will feel how several thousand ants crawl along your legs and bite you. Sometimes a weed can scratch to the blood or stuck strongly, thrown back on the mower.
• Gloves. wandering, leather, it does not matter. If you mowed grass without gloves, then by the end of the kota you will not be able to move even a little finger without pain. The weight of the grass through a trimmer for the grass presses in the hands and abrasions and scuffs will appear on their hands if they were not in protecting gloves.
• Protective glasses. you cannot mow grass with your eyes closed, because small pieces of grass fly in the face. One good hitting your eyes will convince you that protective glasses are mandatory. This applies to one of the main rules how to use a trimmer.
• Have a sufficient amount of drinking water at hand. Even if you think it will not be hot, think again. You need to mow grass with a vibrating trimmer for a long time.
• Have a spare fishing line for a trimmer or a seasoned trimmer head to replace if it ends.
• If you have an electric trimmer for grass, you must have an additional extension cord. If you have a gasoline trimmer for grass, you must have a supply of fuel.
• Rake to rake mowed grass or weeds.
• Headdress if you work in the sun.
• High boots (pants are best tucked into boots).
• If you plan to work at dusk or later, make sure that you have a spray from insects and a lantern.

Safety precautions during work

Safety precautions when working with motorcycles are to fulfill the following requirements.

• Do not use trimmers in the rain or with increased humidity.
• People and animals should be at a distance of at least 15 m from the working device: trimming of grass, small garbage and stones fly out from under the cutting head at high speed and may injure.
• It is better to put on the grass trimmer to a dense fabric that completely closes the arms and legs.
• You need to work in protective glasses, gloves, headdress, closed shoes, special headphones or Berushas.

Important! You can’t stretch your hand or foot to the cutting head!

So, the use of manual vehicles for mowing grass allows you to maintain order on a small area. It is more convenient to use a mower in vast areas. In addition, a trimmer for grass is relevant when harvesting hay and restoring order in the territory: small herbal scraps can be mulched strawberries and other useful plants. You can clearly see the mowing process with this tool on the video.

We get to work

Before starting work, you need to check all the mounts and, if necessary, squeeze them all the way. Put on a rug belt and tighten the adjusting tights.

Then install the braid on a solid flat surface and make sure that the milling cutter is not in contact with anything.

Then you need to set the handle of the throttle to the “OFF” position, and the switch on the handle to position “I”.

Before the first launch, you can pump up a working mixture into the launch system, pressing several times on the soft hemisphere of the valve under the air filter.

Holding the braid with his left hand in a fixed position, the right one must abruptly pull the starter cord.

The engine may not be started the first time, in this case, the attempt should be repeated.

After the engine has begun to work, it is necessary to transfer the handle of the throttle in the “ON” position.

Before work, it is recommended to allow the device to work at idle.

If you need to start the braid immediately after stopping the engine, then you should not close the throttle before the start.

To begin the spitting process, it is necessary to fasten the lawn mower with a carbine to the unloading belt and, holding the trigger, start mowing, using the movement of braids for the grass “right and right” (when using a braid head-“on the left and right”).

On the handle of braids for grass next to the switch there is a button with which you can jam the trigger and work as a tool without unnecessary efforts.

The plane of the cutting tool should be parallel to the ground.

In the work, it is imperative to follow the safety rules and dress according to the requirements. glasses are used to protect the eyes, shoes in boots with non.shaped soles, hands should protect gloves, and from the noise you can use the headphones.

To stop operating the engine, it is enough to transfer the switch on the handle to position “0”.

Protective equipment when working with a motorcycle (trimmer)

Tip: This article does not replace the instructions given in the guide for the use and safety precautions. Always read the product management before use and observe safety precautions.

For safe work with a motorcycle (trimmer) you will need:

• Helmet;
• Headphones;
• Eye protection (mesh shield or glasses, but it is better to use both);
• Long durable pants (the legs are in the immediate vicinity of the knife or fishing line, so they must be protected);
• Shoes with a non.slip sole (preferably with a steel nose);
• Soft gloves (to protect and absorb vibration);

Knives for motorcycles (trimmer for grass)

When working with a motorcycle we can use a fishing line for a trimmer. However, a real advantage (in addition to high engine power) is the ability to equip metal knives.

Various types of knives for trimmers are designed to cut different types of vegetation:

• A knife with 8 or less teeth: grass and weeds;
• A knife with 9-40 teeth: thick weeds and shrubs;
• Knives-saws with more than 40 teeth: small trees and young seedlings;

When replacing a knife, be sure to use gloves.

Each knife indicates the size (diameter) of the landing hole in the center. This is usually 2.5 cm, but cases are different. Therefore, look in the operating manual, what size on your trimmer.

Principle of operation

If we consider the principle of the trimmer for the grass, then it looks like a manual braid. The difference is that it is equipped with an engine, with its help the cutting element is brought into rotation.

Producer companies produce the following models of mowers:

• On which a gasoline engine is installed. Such garden tools have a fuel tank, this is their distinguishing feature.
• Electric engine devices. These tools have less weight, because they do not have a fuel tank. But when choosing such models, you need to take into account that a power source needs their work to work.

All electric braids for grass can be divided into those that work on batteries, and models connected to an electric network. Each species has its own characteristics, but they affect the power supply unit. If you do not take into account it, then the rest of the design are similar in different devices.

If you take any model of a trimmer for grass, then it consists of such elements as:

• motor;
• fuel tank (electric motor does not have it);
• levers with which the mowing is controlled;
• knife for cutting grass;
• barbell;
• Spool with wound fishing line, which is cutting grass;
• protective casing;
• conical gearbox.

The engine is placed near the mowing head, it can be installed from below or from above. Only those models that have a direct bar with a gearbox. If it is curved, then the indigenous bearing becomes a connecting element. It consists of 2 bushings.

As a cutting device, a fishing line for a trimmer is used. It is easy to replace with steel knives and discs, they can be made of plastic or metal.

The choice of cutting element depends on how hard the grass will have to mow. Most often, the work uses a fishing line for a trimmer, it is called the cord. There are products of various shapes on sale, among buyers a spiral and round is in demand.

The fishing line for the trimmer is wound on the coil, it is inserted into the bobbin, while the 2 ends of the wire remain free. Когда двигатель косилки начинает работать, шпулька вращается, трава срезается свободными концами лески.

How to use a trimmer correctly

Garden trimmers for grass are effective. Newchers think that it is easy to work with a lawn mower, because you just need to include it in a socket or pour fuel, but this is not entirely like that.

The efficiency of the garden tool and its service life directly depend on operating conditions. Therefore, before using a trimmer for grass, you need to perform preparatory work.

The lawn with which you need to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flew out from under a working mower, they can injure a person. They remove the wire from the lawn, because it can be wound on a rotating element, break a mower.

After that they move to the installation of the cutting system. There are trimmers for low.power grass on sale, which use only a fishing line for a trimmer. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatts on which metal knives are installed. They cut sowing and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the mounting nut, install the cutting element. Then the nut must be returned to the place, tighten it with the key.

The operator must take care of his safety. Mow grass in tight protective clothes. Special glasses are used to protect the eyes, they will protect from dust, grass and flying garbage. Hands are covered with gloves.

The electric trimmer for the grass is included in the network, and the battery models are charged for several hours before starting operation. Fuel is poured into a gasoline mower.

The mower is kept so that the spool or knife is located parallel to the ground. When the tool is installed in the correct position, the motor is included. After the grass is bewildered, the mower is turned off.

First start

Before the first launch, the operator collects a mower, the procedure is described in the instructions that are attached to the product.

If the trimmer for the grass is gasoline, it is necessarily checked before operation. The fuel tank is filled along the neck.

The motor should work for the fuel, so at the first launch it should work for several minutes without load. After that, start mowing grass.

How to refuel a benzotrimer

Motokos working on gasoline are with two.stroke and four.stroke engines. The first option is much more common. What are the differences between them:

• in trimmers with a 2-tact engine, the response to press the inclusion lever is faster (for this reason the lawn mower is mainly equipped with this type of engine);
• A tool with a two.stroke engine will be much easier, as well as easier to maintain;
• Fuel consumption in a two-stroke engine is higher than in a 4-stroke with a similar power by about 30%;
• The 4x-stroke engine is more environmentally friendly, since the fuel in it burns completely and is not thrown into the atmosphere, as well as its noise level is much lower;
• And the most important distinguishing feature is the refueling: a 2x-stroke engine is equipped with one common tank, where gasoline mixed with butter is poured; 4x-tacte has a separate gas tank and a tank for motor oil.

For refueling, it is necessary to use fresh gasoline AI-92 or AI-95 and high-quality motor oil for garden equipment (for 2x- and 4-tact engines, manufacturers produce different oil). Oil can be used mineral, semi.synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2x-tact engine can be found from the instructions for a specific model. Usually it is 50: 1, in some cases, proportions of 25: 1 or 40: 1 are recommended. Prepare the fuel mixture in a separate container with accurate observance of proportions. Never pour the liquids “by eye” directly into the tank without mixing them in advance. Detailed instructions for mixing a benzomalam, with video and description, can be found on our website here.

Running

Before starting operation, gasoline braids are necessarily rolled up. The operator turns on the motor, he must work for a while at idle. It is necessary to ensure that the engine does not overheat, the load should not be.

When running in, motorcycles increase the load gradually. If you start work with high speeds, the motor will work well, this will affect the further work of the mowing.

At the first launch, you should not fully develop a temporary resource. After the engine works at idle, you can proceed to processing the lawn. The lawn mower should operate for no more than 15 minutes, after which the engine is turned off, it must cool down.

If you need to run the electrimmer, the braid is first collected. Then make trial launches at least 3-5 times. If the engine works well, go to mowing. At first they work for no more than 5 minutes, then the duration of work is gradually increasing.

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer for the grass is fixed on both shoulders if it has a backbone mount.

The model with a bicycle handle is held with 2 hands, the D-shaped handle is wrapped in palm. The belt must be worn so that it is convenient, then the back will not get tired.

How to cut the lawn so that it turns out to be even

So that the grass on the lawn is trimmed evenly, it is necessary to lower the mower as low as possible during operation. The site must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left without interfering under the feet.

Kosim under hay

It is better to mow hay not with a fishing line, but a metal disk. Grass is cut under the root, maintaining its length as much as possible.

Spinning high grass

If you need to mow high grass, this is done in several suits. The lawn processes 2-3 times. The rotating part is lowered from top to bottom, in which case the grass is not wound on the reel.

The operator must remember that the grass wound to the coil leads to overheating of the motor. If this happened, the motorcycle is turned off, and the coil is cleaned.

Most effective mow grass with the ends of the fishing line, and not the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass on the site of a large area, to increase the efficiency of a trimmer for the grass, you must be tilted towards the mowing.