Step-by-step instructions on how to wind fishing line onto a trimmer reel
With the advent of spring, you often spend your time in the country or in a personal plot. A trimmer will protect you from a problem like grass and weeds. This tool easily trims and mows grass in difficult areas where an ordinary lawn mower can’t do it. Trimmer. a very effective and convenient tool for mowing grass along fences, flower beds, houses and aisles in the garden. Invented several types of garden trimmer (gasoline, electric and battery). It would seem that everything is fine, in your arsenal is eating
l such a wonderful helper, but over time the cutting element wears out and there is a need to replace the ended fishing line. But not everyone knows how to refuel a fishing line in a trimmer. We suggest using step-by-step instructions with attached photos.
Instructions on how to wind fishing line onto a trim reel
- 1. First you need to disassemble the trimmer head. Press the latch on the product body and turn the cover clockwise. We take out the bobbin.
- Now we have to figure out how to wind the line onto the reel of the trimmer. We measure out about 6-7 m of fishing line and insert its end into the bobbin hole.
- We wind the fishing line from two sides. The winding direction is always indicated on the bobbin in the form of an arrow.
- Leave the ends of the cutting element 15 cm long free. Do not wind too much fishing line. Leave 6 mm between the outer edge of the bobbin and the fishing line.
- We insert the remaining two ends of the fishing line into the opposite holes of the bobbin.
- We fix both ends in the grooves on the head housing.
- We carefully install the spring back into the guide bobbins and into the head housing.
- In order for the fishing line to be trimmed correctly, it is necessary that the bobbin goes back into the head housing (gently press it). If necessary, pull the loose ends of the fishing line out. In turn, sharply pull the ends of the cutting element so that they come out of the grooves of the bobbin and freely pass through the holes on the head.
- So, we figured out how to wind the line onto the reel of the trimmer. It remains only to combine all the grooves on the head housing and close the lid. Then we press the bobbin and begin to rotate it counterclockwise until it stops. While holding the bobbin, slightly turn clockwise and release it. If there was a click sound, then it clicked into the head. If this does not happen, then you need to repeat the action again.
- Pull the loose ends of the fishing line all the way.
We wind the fishing line on the trimmer reel
Owners who have their own household plots often encounter the problem of keeping a lawn, namely, the need for high-quality mowing of grass. For these purposes, either a manual or an electric braid is used. a trimmer (see photo). It is clear that working with the electric model is much easier and faster. The grass is mowed using a fishing line rotating at high speeds. But during operation, the thread wears out over time and requires a change. So how do you rewind the fishing line on the trimmer reel with your own hands?
Types of fishing line
The thread for the trimmer can be divided into types according to its diameter. It can begin with the smallest. 1.2 millimeters and reach up to 4 millimeters. The most commonly used is a diameter of 2 millimeters. But it is necessary to select it strictly individually, based on the specific model of the device. Often the required diameter of the product is indicated in the passport on the product. Usually the more powerful the trimmer, the larger the diameter of the fishing line should be. For example, it is best to wind a thread with a diameter of 2.4 millimeters on a coil of lawn mowers, and for a product with a weak engine, a thread diameter of 1.6 millimeters is suitable.
Video: How to Put a Coil On a Trimmer Correctly
Fishing lines differ in type of section. It can be round (for mowing ordinary grass), square (for soft and often mowed grass), with sharp edges (for tall grass), with notches (for thin grass), and also complex (see photo). The latter can not be filled in all types of devices. It should be noted that the line is intended solely for mowing grass. To cope with other types of plants, it is necessary to use lawn mowers with a sharp knife. The length of the threads that can be tucked into the trimmer can range from 10 to 100 meters.
How to wind a line onto a trim reel
Spools of products may have different filing systems. This can be manual, semi-automatic or automatic feed. Depending on this, it is necessary to wrap the fishing line. So how do you thread a bobbin? To begin with, the cap is unscrewed on the coil (see video). If the thread on it is left-handed, then you need to turn it clockwise, and not as usual.
Such a thread is made so that during the operation of the product the trimmer head cannot unwind. To fill the thread will require about 5 meters of material (see photo). It must be folded strictly in half, insert the center into the space provided on the device and wind it in the direction of the arrow, which should be drawn on the reel, as in the video. After that, you just need to tighten the cap.
A country toilet is an obligatory attribute of a garden plot. Even if they are not going to build a summer dwelling, for the whole day.
Country cottages of residents of megacities are less and less like garden houses; these are already quite modern “summer residences”. places for relaxation and hobbies.Source: http://stroimdelaem.ru/namatyvaem-lesku-trimmera/
How to wind the line onto the trimmer reel
Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.
So, to rewind the fishing line, you need to first remove the reel from the trimmer. The removal method will depend on the type of trimmer.
On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.
On electric and petrol trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.
On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it you need to grab the lower part with one hand, and # 8212 with the other; top, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.
Now, having removed and disassembled the coil, we proceed, in fact, to the main question # 8212; how to wind the line.
If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.
If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If the grooves are two # 8212; then each antennae wraps around its groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if there are none # 8212; hold with your fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.
If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.
There are still reels in which the line is threaded through the through hole on the inside, the ends of the line, without being wound, are completely threaded through the holes on the outer casing of the reel, the reel is assembled and the button that you usually press is rotated to release the line through the extent of its wear. Rotate the button # 8212; inside the line itself is wound. At the same time twist it in # 171; wrong # 187; direction does not work, because it can spin in only one direction.
That’s all for the matter. Now you know how to wind the line onto the trimmer reel correctly.