How to Wear a Coil On a Trimmer

Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer. it will be more convenient. The removal method will depend on the type of trimmer.

Remove the coil from the trimmer

How to Wear a Coil On a Trimmer

On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

than 200 types of trimmers in one place at the lowest prices. Click and see

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button. the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart. you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.

That’s all for the matter. Good winding!

»How to dress

Spinning Gear # 8212; how to wind the line and use the reel

Proper spinning gear and gear management # 8212; a big contribution to the success of your spinning fishing. About how to handle gear and make the right snap # 8212; Further.

Spinning Transportation Rules

First of all, for the safety of your spinning # 8212; use a special tube. Most spinning models consist of two sections, the length of which is more than a meter. The tube will reliably protect the spinning from the possibility of breaking the tip of the rod, in addition, this is a very convenient way of transportation.

Make sure that you buy a spinning tube with a reel, as this option is much more convenient than a tube for carrying only the rod.

The process of winding fishing line on a reel

Winding fishing line on the reel is as follows:

  1. Put the reel on a spinning rod and pass the end of the line through all the rings, starting from the smallest, gradually reaching the reel itself.
  2. Tilt the bow of the logger (in this state of reel # 8212; the fishing line can easily either enter the reel or reel from it.
  3. On the spool there is a special mount for the end of the fishing line (stopper, usually in the form of a triangle), fix the fishing line (or make an ordinary bundle by wrapping the reel drum, but the first option is preferable.
  4. After that, you can fold the stowing arm back to its original position and start winding the fishing line onto the reel by rotating the reel handle.

It is necessary to wind up almost to the edge of the spool, leaving 1-1.5 millimeters. This will allow you to easily reset the fishing line during casting and at the same time prevent the fishing line from flying off the spool on its own, creating unnecessary loops and knots.

How to use a spinning reel

Before casting # 8212; press the line with your finger and knock over the logger

There is nothing complicated about handling a spinning reel with a spinning reel:

  1. Before casting, make sure that the bait is tightly attached to the end of the fishing line or to the swivel that connects the fishing line and the bait. It allows the fishing line not to twist, thus during the posting the bait behaves more naturally.
  2. By lowering the fishing line from the spool or by winding the reel by turning the handle, make sure that the bait is about 1-1.5 meters from the tip of the spinning rod.
  3. Now, with your index finger, hold down the fishing line that goes from the coil to the first ring and fold the arch of the logger. Now the spool is in a free state if you release your finger # 8212; the fishing line will start to wind up.
  4. Make a swing, not necessarily strong, just take the tip of the rod behind your back or to the side. Now, with a whip (for the first time, not necessarily strong), wave the rod forward, pointing with the tip where the bait needs to fly and at the very last moment release the finger that holds the fishing line.
  5. The fishing line will begin to roll off the spool, and the bait will fly to the place where you cast.
  6. Immediately after the bait lands in water # 8212; Fold the logger to the standard position so that the line does not continue to move off the spool and # 171; beard # 187; is formed.

Video: How to Wear a Coil On a Trimmer


It is necessary to wind the line by rotating the coil, depending on the type of your wiring. If you want to catch the bottom # 8212; wait for the bait to fall to the bottom, holding the fishing line in tension after falling to the bottom # 8212; the line sags a bit, at this point you need to start posting.

If you want to catch on top # 8212; the wiring must be started immediately after the bait falls into the water and quickly rewound.

Use the swivel

Swivel (anti-twist) # 8212; this is a miniature device that will allow your fishing line to not spin from spinning spinners, devons, swinging spinners and other spinning lures.

Also, the swivel often has a convenient clasp, thanks to which you can easily change the bait without unnecessary tearing of the fishing line and another tying.

Use a leash to protect against pike tooth protection

A spinning leash often plays the role of a stronger fishing line at the bait mount. It is designed to prevent the possibility of snacking fishing line with the sharp teeth of a predator.

The leash should be made of durable material, stronger than the main fishing line and at the same time it is desirable that it is less noticeable in water.

In the case of catching asp and other predators that are not able to boast sharp teeth # 8212; You can not use a leash, especially if your main line is not very visible in the water. But when catching toothy pikes, zander and other hunters # 8212; using a leash is extremely important, otherwise you will sooner or later disappointingly be left without bait and fish.

Hard leashes can ruin the game of light lures (for fishing on a wobbler, popper and other light lures, it is advisable to use special elastic leashes).

Spinning # 8212; one of the easiest gear at first glance. It is really quite simple to equip it. But the level of your loot during fishing will depend on your skills. Correct posting of lures and their correct selection greatly increase the chances of catching freshwater predators.

How to reel a fishing line

We wind the fishing line onto the reel correctly!

Fishing is a really exciting and fascinating affair. Novice spinningists, of course, want to quickly join him and finally get an sensible result. The reservoir where you are going to fish is selected, all the necessary accessories are bought. There are rods, reels with baits and fishing lines. too. However. even directly on the shore, even a minor, but still tangible nuisance can wait, which sometimes completely disrupts all fishing.

Her name is winding fishing line. Each coil is equipped, it seems, with an instruction with a basic circuit. But the fact is that with such an attitude a lot can not be caught for sure. With improper winding, the loop can be reset, and instead of removing the fish from the hook, you will have to bother with unraveling the lump from the fishing line with your own hands.

The structure of the winding line can also be very different, it depends on the chosen reel

Start using spinning most often with gear that is shorter (both reels and rods). The caliber of the bobbin in them is two to three thousand (that is, a hundred-meter line is not more than a third of a millimeter thick in this case, the limit). The winding structures can also be very different: this is a chaotic winding in a random arrangement of Chinese samples (more or less suitable for monofilament, but completely inappropriate with braided fishing line), and such more professional formats as a straight cylinder, straight and inverted cone. And from the very beginning it is better to accustom yourself to those types of styling that are more serious, because this is not a whim, but higher efficiency. Having saved fleetingly several hundred rubles, then you will begin to curse everything in the world, when instead of casting and biting (well, or just casting and waiting), fishing will turn into a continuous struggle with “beards” and other fishing line overlays. Such fishing has never brought joy to anyone.

How to quickly wind a line onto a spinning reel

How to wind the line onto the reel. First of all, we fasten the bobbin to a motionless rod-shaped object

The basic, fundamental rule. the equipped fishing line must be as flat as a ruler. For a cylindrical winding, a straight line is optimal, and if a cone is chosen, it is inclined. But in any case, remember it firmly, only fishing line without bends.

How to ensure such leveling in practice? First of all, we fasten the bobbin to a motionless rod-shaped object on which it should easily and freely scroll. Pencils and knitting needles, fountain pens and screwdrivers, small metal tubes without sharp edges, and even a straight and well-polished stick can serve as a rod. As a last resort, find someone who agrees to hold.

Knots for attaching fishing line to the reel

Pull the fishing line through every single rod ring. Tie a knot at the elongated end. Now you can start refueling fishing line on the surface of the reel. First, we attach it over the bobbin in a circle, having previously lifted the arc of the logger, and when another node of the Arbor type is tied and tightened, the arc can be omitted.

The braid line is very fond of slipping. This can be avoided if a piece of rubber (for example, cut off from an unusable fingertip or a worn glove) is poked under the attachment point, in extreme cases, support it with a band-aid if there is no rubber.

And here comes the turn of winding fishing line. Turn the knob on the spool gently and evenly. Make sure that the line goes tight all the time. It must be maintained, but only in tight gauntlets.

When winding, avoid, as far as possible, completing it at the level of the sides of the bobbin. If this rule is not observed, then self-resetting of loops or their terrible tangling become very probable. To avoid this outcome, pay attention to the side even though a millimeter or two remain unreelted fishing line. On the other hand, exceeding a gap of five millimeters may make long-range casting impossible. Prevention is backing (in fact. reeling up the bottom of the main fishing line from the auxiliary, not thicker than three tenths of a millimeter, otherwise even laying will be unattainable). Keep in mind that almost all threads work well in backing, except for long-drying cotton and nylon.

Watch a useful video: how to wind a fishing line onto a reel

To determine how much fishing line to throw on backing is possible only by experiments, there are no ready-made formulas and theoretical provisions on this subject. It will take another bobbin. We wind the main forest onto it, then backing (do not forget about the clearance from the side). Next we attach the main mount, on which we are already introducing fishing lines in the reverse order. Check out our website and read more helpful tips for fishermen.

Similar articles:

  • Long-range float gear
  • How to make a fishing line choker tattoo
  • Winter Pikeperch Accessories
  • We catch perch in winter on mormyshka
  • Drop shot equipment
  • We catch pike in the winter on the balancer

How to wind a fishing line on an inertialess reel

In step 4, we need a spool, that’s how it looks. This is a reel spool with a front clutch, it is turned away at the top of the spool and it can be easily removed, in reels with a rear clutch it is still easier # 8212; just press the button and the spool is removed from the reel

In this guide, for beginner spinning fishers or feeders, we will look at the correct winding of fishing line on an inertia-free reel of a spinning rod or feeder rod.

All you need is:

Winding braided fishing line is no different from winding monofilament or flurocarbon (although in fairness it should be noted that flurocarbon is not used at all as the main fishing line, why do you need it here).

Step-by-step instructions for winding fishing line on an inertialess reel

  1. Insert the reel into your rod.
  2. If the telescopic rod # 8212; pull it in length if the rod is plug-in # 8212; connect the plugs to get working gear.
  3. Take the fishing line and insert its end into the fishing-rod rings starting from the last one (the small one on the tip and ending with the one closest to the reel).
  4. Now remove the spool from the reel (how to do this is described in the figure caption).
  5. Tie the fishing line around the working area of ​​the spool with an ordinary double knot (when the fishing line is folded in half and the simplest knot is made, several knots can be made for fidelity).
  6. Fold the logging rim and reinsert the spool, then close the logging rim to its working position.
  7. You can start winding the fishing line by rotating the handle of the reel, but try to hold the line with your hands so that it enters the reel with a slight tightness (you can hold the line with your hands in the region of the ring closest to the reel).

How to increase fish catch?

For 7 years of active passion for fish, AL-KOI have found dozens of ways to improve biting. I will give the most effective:

  1. Bite activator. This pheromone supplement lures fish the most in cold and warm water. But Rosprirodnadzor intends to ban its sale.
  2. Increase sensitivity gear. Read the relevant manuals for your particular gear type.
  3. Based lures pheromones.

The remaining secrets can be obtained in the free book. You can download it under the article.

Video tutorial on how to reel a fishing line onto a reel

The video contains even more detailed instructions with a story about all the nuances of filling the spool of the reel with fishing line.

Now only pecks from me!

Many of you probably returned home without fish, justifying the lack of catch: bad weather, the wrong place or equipment. It is time to change everything. The best-selling product of the year! Made in Italy.

Sources: http://ranoutrom.com/snasti/spinning/osnastka-spinninga.html, http://www.svoimi-rukamy.com/kak_namotat_lesku_na_katushku.html, http://primanki.com/snasti/spinning/namotka- leski-na-bezynercionnuyu-katushku.html

No comments yet!

Share your opinion

  • enter
  • insert
  • fill
  • charge up
  • land plot
  • to cover
  • put on
  • to clothe
  • to accept
  • Other
  • turn in
  • take off
  • make up
  • to cut
  • lay down
  • install
  • Proper nutrition
  • Right answers
  • Right foundation