Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.
So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer. it will be more convenient. The removal method will depend on the type of trimmer.
Remove the coil from the trimmer
On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.
On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.
On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.
than 200 types of trimmers in one place at the lowest prices. Click and see
Now, having removed and disassembled the coil, we proceed, in fact, to winding.
Winding process
If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.
If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.
If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.
There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button. the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart. you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.
That’s all for the matter. Good winding!
Video: How to Wear a Trimmer Cover Properly
»How to dress
Learn how to plant a braid correctly
A few years ago, the main tool that was used when necessary to harvest hay or mowing weeds on the site was an ordinary scythe. Today, her place was taken by trimmers and lawn mowers, so there were practically no specialists from the old school.
But sometimes it becomes necessary to use this device, which helped our distant ancestors! So how to plant a braid correctly? After all, not only convenience depends on this, but also the safety of work.
What do we need
It is necessary to prepare in advance a dry spruce pole, the length of which should be not less than one and a half to two meters, two rings of metal (inner diameter and width. 4 cm), a wedge of dry birch timber, a piece of bird cherry rod and a piece of durable becheva.
Do not be amazed at such a botanical variety of wood species: each of them has its own unique qualities that are indispensable in a particular situation. By the way, aspen is not ideal for the pole, but aspen. Just a fairly straight aspen pole is quite difficult to find, while there is a tree in every forest.
How to cook wood?
This issue should be given special attention. After studying the instructions on how to plant a scythe, you need to cut down a suitable tree, slightly peel it from the bark (the simplest rough processing is enough), and then hang it, fixing a decent weight on the end.
The latter is done so that the shaft does not bend during the drying process. And this is very important, since it is possible to plant a braid correctly only on a direct Kosovosh.
Beat off
This stage is one of the most important. Beating is done so that a metal packing appears on the braid sheet, which will give the tool additional rigidity and strength. They beat off the canvas towards you, as otherwise you can completely ruin the geometry of the tool. Accordingly, having learned what and how to plant a scythe, you need to get a good hammer and a normal anvil.
Nozzle
Thoroughly clean the end of the pole, align and narrow it. Remember the two metal rings we spoke about at the very beginning? They equate the kososhov up to the very moment until they begin to put on them with some effort. Its end is ground at an angle of about 30 degrees, so that this surface ideally coincides with that for a birch wedge.
Remembering how to fit the braid correctly, we drill one hole in the rings: they will need to be screwed in, which will play the role of a stopper. Pressing the shank of the panel using the aforementioned birch wedge, fasten it with two rings. They are screwed with small screws. In this case, you must ensure that the wood does not crack.
A pen
After that, mark the place under the handle. She is fastened, guided by her own growth. You can read more about this in the instructions that come with the purchased braid.
The pen itself is made from the bird cherry rod we mentioned. It is quite flexible, and therefore it can easily be given the appropriate shape. The ends of the handle for securing are pulled by twine.
We hope that now you clearly imagine how to plant a scythe on a scythe!
Assembly and preparation of the braid for work
A very crucial moment when assembly braids. proper knife attachment on the talisman. An important role in this is played by the bevel angle at the lower end of the space. It should provide a certain rise of the blade of the blade relative to the horizon.
With even terrain, the knife blade in section AA should be raised by 10-20 mm, on bumpy terrain. 25-35 mm. Universal should be considered raising the blade by 20 mm.
If the knife is set incorrectly and the blade is raised higher than the allowed one, the grass cut will be poor and high. With a reduced rise. scythe may dodge down into the soil.
Correctly you should choose the place of the recess for the spike of the heel braids. This moment is involved in the installation of capture braids while mowing. Measurements of distances are carried out with a piece of twine (cord). If the distance from the place of attachment of the handle to the edge of the heel of the braid and to the nose braids will be the same, then the capture is zero. If it is more. capture is positive, if less. negative.
Typically, the grip is set positive in the range of 0-20 mm. Negative capture is established with thick grass and overgrown grasses when their stem becomes rough. After setting the capture braids. without shifting the position of the knife, mount it to the kosovoshu.
Fasten the knife to the kosovoshom using the ring. You can use different rings: either one wide, or two narrow. The ring is fixed with a spreader wedge made of strong wood. Special oblique rings with screws also appear on sale. They also use more advanced ring devices, which not only fasten the knife to the taller, but also regulate the grip braids.
The device, in addition to the ring and the locking screw, is equipped with a clamping pad with holes. The pressure pad has two shoulder edges that are bent. The heel of the knife is very tightly covered braids. The holes on the plate serve both for more reliable fixation of the knife with locking screws, and for adjusting the desired grip of the scythe.
At assembly braids they put a ring on the tomb. Spike heel braids they are placed in a recess-nest prepared on a kosovoshka, a clamping plate is inserted, any of the holes is aligned with the cylindrical end of the locking screw and the screw is tightened very tightly. If necessary, capture changes braids they release the tension of the locking screw and re-align the corresponding hole of the plate with the cylindrical end of the locking screw, while turning the knife braids regarding her spike in the landing nest.
How to choose a braid.
How to choose a braid when buying? How to plant? How to prepare for work in order to mow it was not a hard work, but a pleasure? These questions arise among thousands and thousands of city dwellers who have garden and summer cottages, and those who go to the countryside to harvest fodder at inconveniences. where you can’t use agricultural machinery and where you can turn around only with a scythe.
Perhaps not a single peasant tool requires such careful adjustment as a scythe. Not only that, it should be light, sharp and not stupid for a long time. It should be applied: in this broad concept all ergonomic requirements are enclosed. Parts of the braid should be arranged so that the person does not experience additional unnecessary loads. Then his body will keep straight, swing will become free and natural, his hands will not run numb from an uncomfortable grip. The braid consists of only four parts: the braid itself (cloth), the handle (it has a lot of names. Kosovosh, Kosyos, etc.), handles and mounting parts. However, the relative position of the parts gives many variables, of which it is necessary to make the best option.
It’s hard to teach mowing on paper, but we’ll give some advice. As follows from the heading, it is necessary to mow in the early morning, along the dew, when the grass became soft from night moisture. It is advisable to choose the direction of the pen so that the braid goes towards the slope of the grass, against the wool. The beginning and end of the swing should form a smooth semicircle, in the center of which there is a pigtail. You need to stand straight, with a slight slope forward, legs shoulder-width apart. If you have to bend strongly, it means that the blade is raised high above the ground, the braid must be transplanted. Beginners usually make one major (and many non-core) mistake: they too tear off the heel of the braid from the ground. At the end of the backward stroke, the braid takes off by almost a meter, and when moving forward, the toe crashes into the ground. At first, until automatism appears, you need to follow the heel. In the reverse stroke, do not waste effort on lifting the scythe, just pull it back so that it slides along the stubble, barely coming off the ground. At this point, you can relax the muscles, give them rest. While moving forward, press the heel lightly, then the toe itself rises and does not touch the ground. As you can see, everything is simple. Uniform breathing, free movement. And so on to a sweat.