How to Wrap Fishing Line On Champion Trimmer Video

05 July 2018

A trimmer is a great solution for those who have a large garden or lawn near the house that needs to be constantly cut. But like any other tool, sometimes it requires intervention. After some time, there will be a need to replace certain elements, and this will have to be learned.

How to do this? To replace the main cutting element, you must first select it correctly. In principle, the instruction manual for lawn mowers should indicate the diameter of the thread that should be used in it.

When you have purchased the required cutting element, try installing it correctly. It should be noted that there is a huge amount of video on the Internet that will help you figure out how to properly put fishing line into the trimmer coil.

How to change the line on the trimmer

Below we have provided step-by-step instructions for replacing the trimmer thread.

The first thing to do is disconnect the tool from the mains and turn off the engine. Then you need to remove the trimmer head. This can be done using a simple screwdriver by lowering it into the hole of the gearbox to prevent the shaft from turning. And then just unscrew

  • How to Wrap Fishing Line On Champion Trimmer Video
  • Usually they are unscrewed clockwise, but different models have different mechanisms, so it may have to be twisted in the opposite direction. But if suddenly, for some reason you can’t figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it

    The second one. After removing the mowing head, open it. This can be done by means of latches, which are located opposite each other. By clicking on them, you can remove the head cover, and then pull out the reel from it, on which the fishing line is wound. Pulling it out you can determine what type it belongs to. There are single-section and two-section bobbins

    We disassemble how to fill the fishing line into the trimmer coil in two versions

    So, there is only one option. we charge the fishing line into a single-section coil. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of the winding, do not forget to check that the different ends of the thread look in different directions

    Option two. winding fishing line two-section reel. A pre-prepared thread is divided into two parts, and its ends should be fixed: this should be done by placing them in special fixtures

    Winding is carried out, as in the first case. according to the arrow indicated on the spool. Both segments must be wound so that they do not overlap. Further, the ends of the thread should be fixed in the grooves and divorced on opposite sides

    After that, the spring is inserted into the coil, and all this is placed in the mowing head. When placing the coil in the trimmer, you need to carefully hold the spring while parallelly inserting the line into the slots of the lawn mowing head. And in the end, it just needs to be fixed with the final part, that is, the lid.

    After you tucked the thread into the trimmer, you need to check it. If you did everything correctly, everything will work, if you made a mistake, we recommend that you read the article again, and even better, if you watch a video how to install a fishing line on a reel in a trimmer.

    How to pull a fishing line from a trimmer coil

    Over time, the cutting element of the head wears out, and there is a need to pull out the remnants of the old fishing line. Not everyone knows how to do this. Our step-by-step instruction plus a video on how to pull a thread from a trimmer reel, which you can find on the network, will help in solving this issue.

    It is necessary to disassemble the mowing head

    Using the clips, remove the cover

    We clean the remains of the cutting material

    Complicated ? Of course not. But if, nevertheless, doubts creep into you that for some reason you will not be able to do this, then of course find and watch a video on how to pull out or how to wind a thread on a lawn-mowing reel.

    Video: How to Wrap Fishing Line On Champion Trimmer Video

    How to replace a fishing line on an electric trimmer

    In fact, it makes no difference which oblique you use, whether it is electric or gasoline. Threading is the same. The only difference is that if you use a gas spit, you get more freedom, as it is not limited to the cable that is present on the electric spit

    Yes, do not hesitate to use special videos for installing or refueling the fishing line in an electric scythe, which can teach you much faster than simple reading.

    Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

    So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer. it will be more convenient. The removal method will depend on the type of trimmer.

    Remove the coil from the trimmer

    On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

    On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

    On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

    than 200 types of trimmers in one place at the lowest prices. Click and see

    Now, having removed and disassembled the coil, we proceed, in fact, to winding.

    Winding process

    If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

    If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

    If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

    There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button. the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart. you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.

    That’s all for the matter. Good winding!