Replacing the fuel filter of the Stihl fs lawn mower. Preparation for replacement

Trimmer for STIHL 250 Fuel filter replacement

Dismantling of a chainsaw is a very crucial moment that comes at some point with the owners of such a tool. Owners of chainsaws have to conduct technical service without the help of others. How to disassemble a chainsaw is rapidly and neatly?

The constant technical service of the chainsaw will make it comfortable and non.hazardous.

In order for the chainsaw to work flawlessly, it is often necessary to conduct maintenance consisting of several operations:

• oil substitution;
• fuel share;
• setting up the chain tension;
• cleaning from the mud under the lid;
• inspection and repair of the chain brake;
• Cleaning the oil supply system;
• tire cleansing;
• Cleaning or filter substitution.

Time comes, and all these operations need to be performed. Therefore, you need to learn how to rapidly and correctly disassemble chainsaws.

Stihl has long been loved by lumberjacks thanks to its low price. It can be seen in the hands of summer residents, they do not renounce such a chainsaw and city services.

But in the middle of many positive properties of this model there is one severe defect. Babble very often breaks. over, not every malfunction will be eliminated in agreement with the guarantee. We have to engage in repair without the help of others.

When disassembling and repairing the chainsaws, a certain sequence must be observed.

At first, the cause of the malfunction is determined. Most often happens:

In case of malfunction, it is necessary to remove the gas tank cover and make sure of the uninterrupted fuel supply.

If the chain breaks, it just needs to be replaced with a new. A special problem in such work should not arise. Repair of other malfunctions will require several hours.

If the saw does not start, you must make sure that there is a fuel. To do this, remove the gas tank cover. If the fuel is enough, perhaps a sapun has clogged, which levels the pressure when the fuel is consumed. Sapun can be cleaned with a needle. Candles turn out with a special wrench. They must be cleaned with an sandpaper. The combustion chamber must be damaged. The chainsaw should start.

Automatic shutdown of the chainsaw indicates a malfunction of the starting mechanism. However, this is not always the case. He can work normally. Will have to turn out all the candles and conduct their thorough inspection. If the fuel enters the candle, then the carburetor is clogged. It needs to be removed and cleaned. The incapacitance that appears on the candle indicates the improper adjustment of the carburetor or poor fuel. The twisted candle is checked for performance, the clearance is made. It is best to immediately replace the poorly working candles with new. In addition, the air filter should be clean and not pass the air.

Repair disassembly of Stihl Stihl 250

Repair disassembly of Stihl Stihl 250 Piston Replacement.

After extracting the piston, it is necessary to carefully examine the state of the rings. The landing of the rings should be dense, but they should sit on the piston free. Then the piston must be inserted into the cylinder and try to rock it, leaning on the top point. With a piston chatter, you can safely talk about his wear. Due to such a malfunction, a chainsaw is not able to work for all strength.

If oil leakage is detected, it is necessary to check the joints of the hose and its tightness. To replace the hose, it is necessary to disassemble the entire chainsaw.

The main malfunctions of the chainsaws are:

• ignition;
• fuel mixture;
• piston work;
• cylinder work;
• exhaust;
• chain brake;
• supply of lubricating fluid;
• clutch clutch;
• tire.

Engine repair, ignition

Damage occurs quite often. Dismantling and repair require a lot of time and certain knowledge. Most often, engine repair is required when:

Most of the engine malfunctions are associated with the failure of the ignition system. Therefore, first you need to make sure that the candle is performance. Studying its condition, you can say how well the fuel system works. To do this, they turn the candle with a special wrench, having previously disconnected the wire.

If the candle is absolutely dry, then the problem of damage is not associated with the ignition system. Perhaps the fuel mixture simply does not fall into the cylinder. The candle can be screwed back and start repairing the engine providing the engine with fuel.

When gasoline is found on the candle, it means that the candles are filled. One of the reasons is the incorrect adjustment of the carburetor or violation of the basis of the launch. For repair, the candle needs to be cleaned and dried. To drain the cylinder, you need to close the fuel supply. For ventilation, the combustion chambers start the starter. After a few minutes you can screw the candle and repeat the start. If a black fuel is found on the candle, it means that the fuel system has failed.

Fuel non.allowance has a number of reasons:

• The hole of the cabin was clogged, so a vacuum occurs in the tank, which does not allow fuel to get into the cylinder.
• The fuel filter clogged.
• The carburetor broke.

To determine the cause, you just need to remove the fuel hose, make sure that the fuel flow occurs freely.

If the presentation is very weak, then the saapun is clogged, which can be cleaned with a needle.

Fuel filter removal occurs after draining gasoline from the tank through the pouring hole. It is picked up with a wire hook together with the hose. The connecting clamps are unscrewed. The filter needs to be cleaned or new. It is advisable to change it once a quarter.

The sequence of disassembly of the chainsaw

• The clutch cover is removed.
• The starter cover is removed, for this, the screws are removed and the transverse handle is removed, all the wires are turned off; To remove the top cover, twist the fastening bolts.
• To remove the handle, a lid closing the air filter is removed, the support nuts are unscrewed from above and below.
• To extract the filter, you need to unscrew the bolts fixing the case.
• The dot of the carburetor is freed from the gasoline hose.
• The saw housing is disassembled, for this self.tapping screws are removed, oil tank lid is removed.
• To remove the ignition module, it is necessary to dismantle the clutch drum: the crankshaft is turned in the direction of the clockwise, until the piston when moving up the hole through which the gas production occurs.
• The clutch is released and the flywheel is removed, it is easily removed if it is slightly hit with a hammer on it.
• The screws are unscrewed, the gas tank is removed along with the oil hose, it is removed, weakening the clamps on the oil supply fitting.

Fuel filter

This filter cleans fuel of possible pollution. If it is clogged, gasoline does not enter the cylinder and, accordingly, the unit does not work and does not delay after starting. The fuel filter is located at the end of the intake hose, which is located inside the fuel tank. To get to the filter, you need to remove the tube with the tubes leaving the filter.

Having removed the plug, you can disconnect the intake hose and leave it in the tank. It is removed using tweezers.

Next, remove the old fuel filter from the hose and put a new one, bought in advance. It is also possible to clean the fuel filter if you do not have new. The filter should be attached to the hose using a spring clamp.

Insert the intake pipe into the cork and insert it into the tank.

It should be noted that in some models of trimmers the intake hose is located not inside the tube, but inside the tank. You can remove it with tweezers or hook.

breath

Respiratory valve. This is a check valve designed to align the pressure in the gas tank. If it clogs and does not allow air to flow into the tank, a vacuum forms inside the fuel tank, and fuel ceases to enter the carburetor. To check the valve, remove the hose from the tank to the carburetor. If the gas does not follow the tank, the air intake is clogged.

Trimmer users often ask themselves: where is the fan? This valve is usually located in the gas tank cover and looks like the next number.

It is very easy to clean the fan: disassemble the valve and rinse all its components. In some bush cutters, this valve can be located directly. On the fuel tank. You cannot find it right away, because it is hidden from the eyes under the starter case. Such a respirator is cleaned with an ordinary needle.

Exhaust channel

The reason that the trimmer for the grass has significantly lost power and when trying to increase the engine speed, it slowly lifts them, is often the clogging of the exhaust channel through which exhaust gases emerge from the combustion chamber.

It is necessary to remove the muffler so that the burner does not get inside the cylinder. Next, clean the exhaust pipe from carbon deposits.

This should be done very carefully, avoiding carbon entering the combustion chamber.

After this procedure, the low power of the device and the low speed of rotation of the cutting head will no longer upset you.

Insufficient compression

If the compression is not enough, the engine is not possible in most cases. You can check the compression use a car compressor.

• Remove the spark plug from the engine cylinder.
• Screw the compressor in your place.
• Start tighten the starter cord in the same way as when starting the brush. Do this until the arrow on the measuring device stops moving towards the increase. This value will also show the compression force of this engine.

What should be compressed? Usually compression should be at least 8 kg / cm 2. Although even at 8 kg / cm 2, some engines do not work at idle, since the fuel is not pumped enough. If your mower does not exceed 8 kg / cm 2, you need to check the cylinder, piston and rings.

Poor compression may also be the result of a bulk carburetor. Make sure he is swinging. If so, tighten the mounts that hold it in place. Also, if the carburetor is free, you will notice that gasoline is dripping during operation.

Electric trimmer for grass vibrates

Many mowing users noticed that some time after the device began to work, it begins to vibrate very much. On some trimmers, mainly on more expensive models, an anti.vibration system is installed in the form of shock absorbers located between the engine and the bar. But in some cases, even this does not save from strong vibrations. The cause of vibration in the trimmer can be a small amount or complete absence of lubrication on a hard or flexible shaft located inside the core of the device.

Replacing the lubrication of the hard shaft is as follows:

• unscrew and remove the mowing head;
• Remove the stem from the motor by unscrewing a couple of bolts;
• pull out a flexible cable from the bar;
• Lubricate the cable along its length.

To do this, you first need to lubricate the end of the cable, then insert it into the core, then, moving inside the pipe, grease the part and evenly distribute it on the surface. Then insert a flexible motor into the motor and fix it.

If the lubricant does not help and the vibration continues to occur, it is necessary to replace the flexible shaft.

Trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

• gasoline does not have an octane number specified in the instructions of the device;
• The proportions of gasoline and oil were not observed in the preparation of the fuel mixture;
• The mixture of fuel oil was prepared for a long time (the mixture cannot be stored for more than 2 weeks);
• The trimmer for the grass works outside the set time;
• A trimmer for low.power grass used on dense and solid grass, the device is overloaded and quickly heats up;
• The displacement towards the rod or the cartridge lid jammed.

The latter will happen if you install the mower is not suitable for this device, or when the axis is shifted inside the arrow. These changes complicate rotation, increase the load on the engine, and it overheats.

Replacing the fuel filter of the lawn mower (trimmer for grass)

Any STIHL lawn mower is designed strictly for the work provided for in the engine power. The manufacturer categorically does not advise without the help of others to receive or to improve the device of braids for grass. Therefore, while taking the Stihl lawn mower, you need to correctly determine with the upcoming front of the work.

It is completely inappropriate to receive a powerful trimmer for grass for repeating mowing of grass in the clearing, for this purpose there are enough light gasoline or electronic models of mowers.

• Observe the mode: work/rest at intervals for 20 minutes.
• Use high-quality gasoline at least AI-92.
• For the manufacture of fuel consistency, the original stihl engine oil (50: 1) should be used.
• When driving a motor up to 2-3 full refueling of the fuel tank, prevent operation on a critical load.
• When preserving braids for grass for the winter period or an alleged break in operation, in order to avoid breakdowns of the motor, you should certainly drain the remnants of gasoline from the fuel tank.
• To ensure measured functioning, to systematically inspect the condition of the fuel filter. to clean it differently with new.
• To prevent severe malfunctions, you need to avoid clogging of the air filter.
• Make safety requirements during the operation of the Stihl lawn mower.

Accurate adherence to the requirements of the operating annotation is the key to long.term and non.penal work of the Stihl motorcycles.

To mechanize the work on mowing of grass in a small section, the Stihl FS38 lawn mower is adapted in the best way. The cleanliness and accuracy of the cut, mobility, lightness and the highest performance are high advantages, in comparison with a manual oblique.

How to refuel a braid head to the STIHL FS 38 motorcycle

From defects, owners often note that immediately after starting, the STIHL lawn mower can simply stall. In this case, it is necessary to check the fuel channel for clogging. Another reason is hidden in the incorrect adjustment of the carburetor, which is simply eliminated accordingly with maintenance tips.

A recognizable brand guarantees the reliability of certified products, which is noted by the owners of technology.

Service and repair of the STIHL FS38 motorcade

Lawn mower Stihl FS38 All.Propquorted “sore”

“I bought a STIHL FS38 motorcycle for constant mowing of grass in approximately 10 acres. For 7 years of work, I was able to serve the site as easier to serve such equipment. The engine is quite economical, this is not enough to clear the bushes of its power. Comfortable handle shoulder, work comfortably “.

The spark is gone in a stihl gas station does not start a lawn mower there is no spark in a benzocos. We solve the problem.

They are discussing today

Thanks for the alignment. I did not listen to you and, still wrote to him! There was no answer and not only that, he blocked me again! Anna, please, I need an individual alignment. I love him very much, but if I am sure that he does not need me, I.

David I watch constantly your fuss. Thanks and post the next. Worked as a trucker in the USSR and I envy you good envy. Good luck in life and work.

The continuation of the find of the location of the Ishim treasure and the definition of what kind of place it was, for which it was created, I would like to know in the near future. A very interesting story, today.

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

• The voltage in the network is below the required minimum for the device more than 10%;
• There was a failure on a smooth launch (if there is such a system);
• there was a malfunction of the brush node;
• The engine winding was burned;
• rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

note! With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

Note! The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.

Low quality fuel use

Benzotrimmer does not gain momentum in case of low quality fuel. He may stall or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for problems with the combustion chamber.

In the presence of sediment, plaque formed on the candles, the old fuel is drained and flooded another, high.quality.

It must be remembered that a trimmer for grass or a lawn mower should be refueling good quality gasoline and those fuel brands that the manufacturer indicated in the technical passport of the device.

Note! Candles should be thoroughly cleaned of plaque, and only after that place again in the combustion chamber of fuel.

FLOOK DISCOUNSE

The lack of fuel circulation in the system can also be the reason why the device does not gain momentum. There are several options for why this is happening:

You can eliminate problems yourself. For this you need:

• remove blockages from the gasoline pump;
• update hoses, pipes for fuel circulation;
• Clean the muffler and mesh on it;
• Reinching a new catalyst.

Do not worry when such problems arise. This does not mean at all that the unit of poor quality. If the Patriot trimmer does not gain momentum, it can be repaired with your own hands without contacting the service.

Air or fuel filter pollution

There is a lawn mower does not gain speed, the reasons may be polluted by the filter element: air or fuel.

When blocking the air filter, there is a lack of oxygen in the combustion chamber, so the fuel is not fully produced, which prevents the desired speed and power.

To check if the cause is really in the air filter, you need to remove it and turn it on. If the lawn mower still does not gain momentum, the reasons are not in it. So you should check the fuel filter element. Everything is similar here, only gasoline acts as oxygen. If this filter is damaged, there will be a lack of fuel, which inhibits the development of revolutions.

Tips for quickly launching the unit

How to clean and store a tool?

During the operation of the lawn mower, monitor the state of the engine cooling system. The channels available in the starter housing, as well as the cylinder ribs, should always be clean. If you ignore this requirement and continue to operate the motorcycle, then you can disable the engine due to overheating.

Competent care of gasoline scythe during operation allows you to use it for several seasons in a row without serious repair

Before cleaning, let the engine cool down. Take a brush with a soft pile and clean the outer surface from dirt. Cleaning plastic parts is carried out by solvents, including kerosene, or special detergents.

After the summer season, the lawn mower should be prepared for long.term storage. To do this, the fuel mixture is drained from the tank. Then the engine is launched in order to develop fuel residues in a carburetor. The entire tool is well cleaned of pollution and sent to “hibernation”.

As you can see, it is possible to repair the malfunctions of the household lawn mowed on their own. Service services should be contacted in case of serious breakdowns. In this case, the cost of repairs with the price of a new lawn mower should be correlated. Perhaps it will be more advisable to buy a new tool.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

• low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
• The grass was wound on the shaft of the fishing/knife head;
• clogging of the air filter/muffler;
• Balance of the carburetor.

Problems with ignition candles

When a benzotrimer is used often, you need to monitor the state. This part is susceptible to wear, so they need to be regularly examined: is there a Nagar on them.

You can solve the problem in two ways: clean the old candle from Gary or purchase a new one.

In the first case, you need to unscrew and swing with sandpaper, dry. The distance between the electrodes should be 1 mm. Trimmer for grass is collected and advanced.

In the absence of a spark between the electrodes, it is worth inspecting the quality of the connections of all the elements of the circuit. If in this case everything is fine, then 100% you need to change the candles.

Replacing them is easy and inexpensive. From the tools will be needed a key, supervisor.

Important! With frequent appearance of soot on the candlelights, it is worth looking for a reason a little deeper.

Candles should be carefully cleaned of plaque

Fuel tank (fuel quality)

Remember that always before starting the unit, a check of the presence and quality of fuel is required. In this case, you should not be greedy and save, as well as “clever” about the amount of oil added. Everything must be done according to the management attached to the apparatus, since when the piston group fails, its replacement will cost about 70% of the total cost of the trimmer for the grass. Pour fuel due to the fact that you will fully conside it when performing work. After a while, the gasoline remaining in the tank loses its properties and can harm the engine. Therefore, do not prepare the mixture for the future and in large quantities. If the lawn mower starts poorly, try to drain the “old” fuel from the tank, and season it with a freshly prepared mixture.

Replacing the fuel filter of the lawn mower (trimmer for grass)

Important! To refuel the device with fuel, the origin of which is unknown, fraught with negative consequences. Gasoline should be of high quality, bought at a gas station, and its brand should be not lower than AI-95.

Insufficient compression

If the compression is insufficient, then starting the engine, in most cases, will not work. To check the compression, you can use the car compressometer.

• Twist a candle from the ICE cylinder.
• Screw in its place a compressometer.
• Start pulling the launch cord as you do when starting a lawn mower. Do this until the shooter on the measuring device stops moving towards the increase. This value will show the compression force of this engine.

What compression should be? Normally, the compression should be at least 8 kg/cm 2. Although even at 8 kg/cm 2, some engines do not have idle and stall, since the fuel does not pump in a sufficient way. If your gas station does not pump above 8 kg/cm 2. you have to check the cylinder, piston and rings.

Repair of a trimmer for the grass Stihl FS 55. Replacing the fuel filter on the motorcycle “Stihl”

Poor compression can also be due to a slightly screwed carburetor. Check if he is staggering. If so, then tighten the fastener that holds it. Also, if the carburetor is poorly screwed, you can notice that gasoline is dripping during operation.

Lawn mowed FS 38 Fuel filter replacement

The Stihl FS38 lawn mower belongs to a light group and is a good addition to a strong lawn mower for the design of inaccessible areas, along the paths, under trees and bushes. Using the STIHL mobile lawn mower there is an option to rapidly cut the soft, overgrown grass on lawns and meadows, always contain a small area in a clean state.

• Model. FS 38 Autocut.
• Mass. 4.1 kg (without cutting equipment).
• Motokosa length. 147 cm (without cutting equipment).
• Motor type. two.stroke.
• Cylinder volume. 27.3.5 cubic meter. cm.
• Power. 0.9 liters.With.
• Type of fuel. gasoline.
• Gasoline consumption. 0.32l/hour.
• Fuel tank volume. 0.33 liters.
• Pen. radial pen.
• Speasing dialect. 380 mm.
• The largest number of revolutions of the working head is 9500 rpm.
• Anti.vibration system. installed.
• Light starting system. installed.
• Cutting tools-Autocut head C 5-2 (included).

The Stihl FS38 Lawn Mobilum. the easiest mobile version with a capacity of 0.9 liters.With., It is created for domestic use.

• Thanks to the modern electric ignition system, reliable start and uninterrupted operation of the motor is ensured.
• With the use of the fuel pump, the operator will be able, if necessary, to pump up the fuel in the carburetor.
• The best maneuverability is provided thanks to the D-shaped handle, with the help of which it is necessary to comfortably control the Stihl motorcycle carpet while working in complex areas.
• Our client remains the control levers located on a special functional handle (R), which ensures the safety and reliability of the gasolimmer operation.
• Thanks to the Autocut C5-2 mowing headset, the mowing dialect is 380 mm.
• The ergonomic shoulder belt allows you to delay the STIHL motorcycle cub on the shoulder, properly coordinate movements during operation.
• Small mass (4.1 kg.), small dimensions, rational basic equipment. thanks to these features, the STIHL 38 lawn mower is very comfortable in work.

Read Replacing the bearing on the Interskol corner grinder

Replacing the fuel filter of the lawn mower (trimmer for grass)

Any STIHL lawn mower is designed strictly for the work provided for in the engine power. The manufacturer categorically does not advise without the help of others to receive or to improve the device of braids for grass. Therefore, while taking the Stihl lawn mower, you need to correctly determine with the upcoming front of the work.

It is completely inappropriate to receive a powerful trimmer for grass for repeating mowing of grass in the clearing, for this purpose there are enough light gasoline or electronic models of mowers.

• Observe the mode: work/rest at intervals for 20 minutes.
• Use high-quality gasoline at least AI-92.
• For the manufacture of fuel consistency, the original stihl engine oil (50: 1) should be used.
• When driving a motor up to 2-3 full refueling of the fuel tank, prevent operation on a critical load.
• When preserving braids for grass for the winter period or an alleged break in operation, in order to avoid breakdowns of the motor, you should certainly drain the remnants of gasoline from the fuel tank.
• To ensure measured functioning, to systematically inspect the condition of the fuel filter. to clean it differently with new.
• To prevent severe malfunctions, you need to avoid clogging of the air filter.
• Make safety requirements during the operation of the Stihl lawn mower.

Read where is the Air filter on the Champion trimmer

Accurate adherence to the requirements of the operating annotation is the key to long.term and non.penal work of the Stihl motorcycles.

To mechanize the work on mowing of grass in a small section, the Stihl FS38 lawn mower is adapted in the best way. The cleanliness and accuracy of the cut, mobility, lightness and the highest performance are high advantages, in comparison with a manual oblique.

How to refuel a braid head to the STIHL FS 38 motorcycle

From defects, owners often note that immediately after starting, the STIHL lawn mower can simply stall. In this case, it is necessary to check the fuel

Channel for clogging. Another reason is hidden in the incorrect adjustment of the carburetor, which is simply eliminated accordingly with maintenance tips.

A recognizable brand guarantees the reliability of certified products, which is noted by the owners of technology.

Service and repair of the STIHL FS38 motorcade

STIHL FS38 All.Promised “sore”

“I bought a STIHL FS38 motorcycle for constant mowing of grass in approximately 10 acres. For 7 years of work, I was able to serve the site as easier to serve such equipment. The engine is quite economical, this is not enough to clear the bushes of its power. Comfortable handle shoulder, work comfortably “.

Features and best models

A mowing man deserves a separate mention. Characterized by its multifunctionality, reliability and ease of operation. The company’s specialists developed many varieties of braids, with various characteristics and use.

For example, the range of lawn mowers is designed to mow grass in large spaces. For this, a self.propelled wheel system was developed, with which it became possible to care for a large territory, and not spending a lot of time and effort on it. For the design of shrubs, giving them a certain artistic image and texture, the lawn mower is perfect. And if you need a lawn mower for high grass and uneven areas, then follow this link and receive complete information on the selection of this type of equipment.

If you need a thinner approach to grass cleaning, for example, near flower beds or between trees, then a gasoline trimmer for grass, designed for accuracy and accuracy of execution, will perfectly cope with this task. The company’s specialists have provided all the nuances and probable difficulties in working with the hair, so they supplied them with nylon.signs with strings, which prevent mechanical damage to trees.

Autocut special trimmer head is also used, which provides the normal functionality of the string knives trimmer for grass. In for gasoline lawmakers trimmers for grass, this article will tell you, it will also help you make the right purchase in which you will not regret.

Two types of these mowers are distinguished: amateur and professional models designed to solve problems of a certain complexity. The first category includes FS 38, FS 45, FS 55, etc. Features and differences of these tools are the power of the motor (from 0.9 to 1.2 liters.With. Depending on the configuration) and the volume of the tank (approximately 0, 34 l).

Professional include trimmers for STIHL FS 130 and FS 250 grass. We consider the characteristics and properties for the example of several braids, in particular FS 38, FS 70 and FS 130.

Watch the features of the device on the video.

Recommendations for operation

It is necessary to take time breaks in work. This is necessary so that the engine engine does not overheat and does not fail ahead of time. For amateur models, there is a break every 20 minutes for the same time. For professional braids, you need to interrupt work every 50 minutes, in this case, the downtime should be not 10 minutes.

Read how to screw a screw without an electric screwdriver

You need to follow the condition of the fuel tank. If you do not plan to use a mower for a certain time, it is better to drain the remnants of fuel from the tank compartment. This will help to avoid a breakdown of engine parts.

It is a more advanced model, characterized by higher power and multitasking. An anti.vibration system is provided that allows to significantly reduce the effects of the operating engine on the handle.

New generation engine allows you to reduce fuel consumption. The cost of this model varies, but the average price is about 300 dollars.

• engine power. 1.2 l.With;
• engine volume. 27.2 cm3;
• tank volume. 0.34 l;
• engine type. two.stroke;
• The bar is straight;
• The handle is T-shaped;
• equipment. a belt, a coil with a fishing line;
• Field diameter. 2.4 mm;
• Weight. 5.4 kg.

Checking filters

Another all-produced prerequisite, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the hypothesis, quite dismantle the designated block and experience the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to create an air filter substitution or at least perform a painstaking blowing of an old. In the presence of abundant contaminants on the surface of the filter element, you need to use the latest grid. Relying to similar actions, you should not leave an absorbing pipe completely without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

The lawn mower is not started, the spark is gone

The loss of the spark enters the contact verification and the correctness of the clearance between them, conducting the wire to the candle and the candle itself. The sparking method. turn out the candle, connect the wire to it, attach the candle sideways to the motor’s casing and pull the lawn.mowing a couple of times a couple of times, while you need to look at the corner and contact of the candle, you should run a spark between them. If there is no sparks, take the latest candle to make the same function, if with all this the spark is not tracked down, the inconsistent in the wire or contacts is made, it is better to change them.

Portal about construction

Gasoline trimmers for grass are completely indispensable in the elimination of weed thickets in the backyard, as well as when harvesting hay. Yes, as a grandfather’s “Lithuanian” they also showed themselves indispensable assistants. There is only one problem: even ancient braids for grass after the season had to be repaired.

What to do in the case when the gasoline trimmer for the grass broke? Repair in a service center. pleasure is not cheap. Is there a chance to somehow correct the situation on their own?

Checking filters

Another all-produced prerequisite, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the hypothesis, quite dismantle the designated block and experience the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to create an air filter substitution or at least perform a painstaking blowing of an old. In the presence of abundant contaminants on the surface of the filter element, you need to use the latest grid. Relying to similar actions, you should not leave an absorbing pipe completely without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

The lawn mower is not started, the spark is gone

The loss of the spark enters the contact verification and the correctness of the clearance between them, conducting the wire to the candle and the candle itself. The sparking method. turn out the candle, connect the wire to it, attach the candle sideways to the motor’s casing and pull the lawn.mowing a couple of times a couple of times, while you need to look at the corner and contact of the candle, you should run a spark between them. If there is no sparks, take the latest candle to make the same function, if with all this the spark is not tracked down, the inconsistent in the wire or contacts is made, it is better to change them.

Portal about construction

Gasoline trimmers for grass are completely indispensable in the elimination of weed thickets in the backyard, as well as when harvesting hay. Yes, as a grandfather’s “Lithuanian” they also showed themselves indispensable assistants. There is only one problem: even ancient braids for grass after the season had to be repaired.

What to do in the case when the gasoline trimmer for the grass broke? Repair in a service center. pleasure is not cheap. Is there a chance to somehow correct the situation on their own?