STIHL lawners fill the candle with what to do.

Trimmer for grass gasoline Champion T334 does not start, wet candle.

Before resorting to more serious repair actions, you must make sure that the graduation channel is serviceable. This section does not apply to previously not used trimmers, since they have practically no production. If the lawn mower is operated for many years and during this time the unit was not subject to serious diagnostic measures, then it is necessary to check the fact of the clogging of the muffler.

The accumulation of soot prevents the exhaust gases from going out, which is why it is simply impossible to start the engine. Of course, on one day the graduation channel cannot clog, which is why such a situation should be preceded by certain signs. The exit of black smoke from a silencer is a kind of incapacity, which gradually accumulates on the walls of the exhaust system. A significant increase in the sound of the installed motor may occur, which is associated with overcoming huge resistance with exhaust gases to release them. When working at idle, the device stalls spontaneously. In critical situations, the engine operation is significantly deteriorated.

If there are serious pollution on the anti.skill net, then the reason for the impossibility of starting a trimmer engine may be precisely in the final channel. You need to clean the mesh as carefully as possible, since it is the black cargo that is a carcinogen that is very dangerous for a person, which can provoke damage to the respiratory tract. For cleaning, specialized tools should be used that will cope with the soil.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

• Gasoline has not the same octane number indicated in the instructions for the unit;
• the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
• A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
• The trimmer for the grass works more than the time instructions;
• A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
• shifted towards the bar or the cassette lid clutched.

The latter happens if you install the mowing head inappropriate for this unit

, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

Why the lawn mower is not started. we eliminate the problems

When caring for a personal plot, summer residents periodically face the fact that the lawn mower is not started. There are many reasons for the refusal of the tool. For the correct diagnosis of the problem, the owner of the useful in the country’s dive must know the device and the principle of operation of its individual parts.

Since the gasoline trimmer for grass refers to complex devices, before starting work, it is necessary to carefully study the operating instructions. Very often it is simply ignored, or they get acquainted with it superficially. As a result, when the tool stalls or refuses to start, the question arises. “why the lawn mower is not started?»A long seasonal break in work, improper storage and untimely maintenance of a trimmer for grass, will deliver a lot of trouble to the summer resident, to eliminate the reasons.

Where to start diagnostics motorcycles

If the lawn mower does not start or immediately stalls after starting, it is necessary to sequentially check all the main nodes and assemblies. The test algorithm is as follows:

• Fuel tank (fuel quality);
• Candle and candle channel;
• Air filter;
• Fuel filter;
• Breather;
• Graduation channel.

These nodes are most often source of basic problems, which can be eliminated after a thorough inspection.

Check the fuel mixture

Before starting the engine of a gasoline braid for grass, check the presence, and the quality of the fuel mixture. Do not save, do not greedy and “do not smarter” in this matter. Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil fuel mixture strictly according to the instructions. Calculate its number from real needs. Excess gasoline left after work loses its qualities over time.

We diagnose a candle and candle canal

If the quality of the fuel mixture is not in doubt, and the lawn mower stalls when starting, then a flooded candle may be the reason. Here, a regular candle key is suitable for repair (every motorist has probably has a spare candle.

• We twist the candle and wipe;
• We thoroughly dry it (you should not bake it);
• Excess fuel in the chamber we drain through the candle hole and dry it;
• We clean the old candle from the carbon on a sugar or a ladies’ file;
• We set a gap with a distance of 1 mm (you can check with any coin);
• We return everything to place and try to start a trimmer for the grass.

Dry the channel at least 30-40 minutes. Otherwise, there is a risk of re.pour a new candle.

If the working candle is working, the nest, where it is located completely dry, and the lawn mower does not want to start, lubricate the threaded connection with gasoline. It should be slightly moisturized. No matter what wonderful spark gives out a candle, there is simply nothing to light up in a dry chamber.

If the trimmer engine for grass still does not start, such a cause as the lack of spark due to weak contact between candles and a high-voltage wire should be excluded. If the connection is of high quality, and there are no sparks, most likely, you have “flew” the ignition unit. Here you can’t do without a master, t. to. The part is not repaired, but sold by a whole knot.

Diagnosis of the filters of the lawn mower

Another reason why the gasoline braid for grass stalls is an air filter. To exclude it, try to remove the filter and start a trimmer for grass without it. If it turns out, then you will have to change the air filter to a new one, or at least blow and carefully clean the old.

You can’t start a gasoline trimmer for grass due to contamination of the fuel filter. This is the next stage of our algorithm. Here we check the state of the filter element and, if necessary, change it with the new. When replacing, try not to leave a suction pipe without a filter, this is prohibited by any operating instructions. Rush can turn into the repair of the piston group of the engine.

Sapun and graduation channel

Often, “delicate” branded models of benzos are not launched and stall due. The main function of this element is to align the pressure in the gas tank. When clogging this node, a vacuum is created in the tank that prevents the supply of fuel. Eliminate the malfunction can be cleaned by cleaning the sounds. You can use a regular needle for cleaning.

Normal work of cos with internal combustion engines can be disturbed due to dirt from the exhaust channel or clogging of the muffler grid. There is such a problem on the models of the older generation. You can solve the issue with traditional cleaning and removal.

complex reasons for the refusal of the lawn mower

If the step-by-step algorithm for searching for a malfunction has not given a result, and your braid for grass still does not start or stalls, it is worth examining the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable operation of the tool. Three main problems can be distinguished here:

• Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a powerful stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
• Wear of the carburetor laying. Output. replacing the failed laying;
• Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it with the right. Follow the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, then some part of the carburetor is faulty. Will have to find it and replace it with a new.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips, scratches or bully are found, on the piston or cylinder they should be replaced. Piston rings are subject to mandatory verification. A small rally piston when swaying the connecting rod indicates that the time has come to change the rings. This procedure is best entrusted to the specialists of the service center.

Rules for the operation and storage of a lawn mower

In order for the lawn mower to start well and continue to provide it with good storage and operation conditions:

Floods the candle on the trimmer what to do

28.02.202010.05.2020

Gas trimmer for grass. An amazingly useful tool that can mow not only a miniature lawn in front of the house, but also a whole large lawn. Unfortunately, there is nothing eternal in this world, and therefore you may face the fact that gas trimmers for the grass are not launched.

Often users of these machines are trying to “save”, pouring into the tank not fuel with a normal octane number, but something obscure that was in a plastic canister for almost ten years.

The main thing. Fuel mixture!

In this case, the remnants of plastic dissolved in an aggressive environment do such terrible things in the combustion chamber that you definitely cannot do without a complete sorting of the mechanism. But, of course, you will always remember how to store fuel correctly.

What to do when the fuel is normal, a spark appears, but the gas trimmer for the grass does not start? Perhaps you just flooded the candle with gasoline. In this case, it must be turned out, wiped with a clean cloth and dried. By the way, do not check the candle itself.

Have a cold start!

Often gas trimmers for grass are not launched after they tried to “put them into operation” after long.term storage. The failure in this case is often associated with the incorrect actions of the user.

If you are faced with this phenomenon, then during the cold launch you need to close the damper, and then enter a small amount of fuel mixture into the carburetor. Then pull the starter handle until you feel the resistance, and then turn on the trimmer for the grass with sharp and energetic movements.

reasons

There are not only situations when gas trimmers for grass are not launched, but there are times when they are launched within a few seconds after launch, and then with a delay. Check the light of the ignition again: if it is “thrown away” and this situation is repeated even after it is wiped and dried, proceed to check the “air filter”.

Most likely, it is completely lubricated and requires replacement. If everything is in order with the filter, the ignition coil may be faulty.

If gas trimmers for grass are not launched, and you have completed all of the above, the muffler can be clogged. It must be disassembled and burned, after which all soot can be easily shaken off.

Well, even if your trimmer for the grass does not start after such bullying, you cannot do without disassembling a carburetor. It may well be that the needle is to blame for this. In any case, the disassembly and washing of this capricious mechanism will probably not hurt.

As a rule, when a trimmer for grass begins to harden and linger, it is recommended to carry out complete prevention: completely replace the fuel mixture, try another oil and replace the candle without fail. Practice shows that in many cases cheap low.quality candles are to blame.

We examined the most common reasons why the trimmer for the grass does not start. If this is more exotic, do not go to the service center. You will probably find minor and obvious damage yourself.

What to do if the candle was filled with gasoline

There are 2 options for solving the problem. In the “reasonable” operating book, as a rule, it is written: if the injector candles are flooded with fuel, then it is necessary to unscrew them and dry them. With the candle removed, turn the starter for 10-15 s. Insert the candles back and start the motor.

Reliable folk method. If you poured candles with gasoline before you twist and dry them, try to start the engine with a subsequent technique: purging mode.

Gas handle is completely unscrewed, in the floor. Start the engine with a starter 10-12 seconds, let go of the gas handle. The engine is obliged to start. The fact is that in a similar way you, closing the supply of fuel, blow out the air with air.

If the engine does not start, then try to dry the candles then. The spark plugs for the injector are no different, from the engine with the carburetor. Therefore, we again use the “ancient” method: we unscrew the candles, clean them of a crocheted brush, dry or a hairdryer, or on a gas stove or in the oven. Control the gap and screw the candles in place. The motor should start.

For those who have been used by scooters, consultation of professionals is often to clean the candles, and even more correctly, their change.

If the candles are constantly filled with gasoline constantly, it is necessary to diagnose: candles on the quality of sparking, the cleanliness of the nozzles, the exit of the spark from the ignition coil, the Hall sensor.

Features of diagnosis

Trammers for grass can be attributed from a technical point of view to complex devices. Based on this, before their operation, it is strongly recommended to carefully study the relevant instruction. However, in practice, many ignore it, often then find themselves in situations where the gasoline trimmer for the grass does not start or is poorly gaining momentum in the process. It is worth noting that you can encounter such problems by purchasing new samples of technology.

One of the most common causes of such symptoms is a long seasonal break in the operation of equipment. In addition, poor.quality and untimely maintenance can lead to extremely negative consequences. It is important to remember that this is relevant for both the Chinese lawn mower and the representatives of the model rows of eminent brands.

The key to effective and operational repair will, of course, be competent diagnostics of the device. In the process of identifying malfunctions, you will have to inspect and test, first of all, key elements. The list of such includes candles, tank, filter nodes and valves of the fuel system. As practice shows, very often the malfunctions of these elements become the reason that the lawn mower does not start. The quality and correctness of the preparation of the fuel mixture deserves special attention, especially when it comes to two.stroke engines. In relation to this parameter, the manufacturer’s recommendations should be clearly followed in order to avoid serious breakdowns and expensive repair work. In the case of, for example, with the Piston Group of ICE, expenses are able to amount to 70 percent of the cost of new equipment.

Often, the owners of the trimmers have to deal with situations when the indicated mixture is high.quality, the carburetor is serviceable and configured, and the device still does not show signs of life when trying to start the engine. In such cases, the condition of the candle should be checked. The following steps will allow to eliminate the problem:

• turn out the candle;
• wipe and dry the part (pumping is undesirable);
• remove fuel and dry the candle channel for 30–40 minutes; Such actions will avoid filling the candle with another attempt to launch;
• completely eliminate the traces of soot using a file or sandpaper;
• set the appropriate gap;
• put the candle in place.

If the candle turned out to be the working and the planting nest is completely dry, and the engine of the braid for the grass is not started, then the thread should be moistened with gasoline. It is worth remembering that regardless of the quality of the issued spark, initially in a completely dry chamber, there will simply be nothing to ignite. Faced with the fact that the spark does not act, it is worth paying attention to checking the contact between high.voltage wiring and candles. If this connection is of high quality, then it will be necessary to check the performance of the ignition control unit unit. In such cases, a qualified specialist is unlikely to do without services.

The next stage in the diagnosis of gasoline braid for grass will be checking the state of filters. Often, the lawn mower is poorly started or does not start at all on the cold due to the fact that the air filter is clogged. This malfunction can be identified by excluding it from the system. If after that the braid for the grass starts, then you will have to clean or change this element. Experienced users strongly recommend periodically blowing an air filter to maximize its operation.

floods a candle on a benzoca

The described tool can also not be started due to problems with the supply of gasoline provoked by fuel filter pollution. For the quick and efficient elimination of such a breakdown, you just need to replace the filter element with a new. It is important to remember that the suction pipe must be equipped with a filter, which is provided for by all instructions. Non.compliance with these rules and recommendations may entail expensive piston repair. In the process of diagnosing and searching for source of problems with the launch of a mower, attention should be paid to the saapun responsible for stabilizing the leveling of pressure in the fuel tank. In addition, it is necessary to check the cleanliness of the exhaust channel and muffler grid. As a rule, such problems are most often encountered during the defect of old models.

The reliability of mounted filters

It is these devices that often become an obstacle, due to which a classic trimmer for grass does not start. The filter provided by manufacturers is responsible for the high.quality cleaning of air entering the carburetor. The clogging of the cleansing node is fraught with the fact that oxygen enters the internal compartment of the unit in a smaller quantity or its supply is completely stopped. You can determine the air filter malfunction in a rather simple and affordable way:

• Dismantle the device and carefully inspect it.
• If clogged clogs were not found with the naked eye, then try to start a lawn mower without a filter. This detail needs to be replaced only if the trimmer for the grass has successfully wound up.
• To clean the air filter, you can use a stream of compressed air. But if the cleaning device has long been used, then it is more advisable to replace it.

It is worth noting that the trimmers for the grass do not start due to clogging of the air filter in the most rare cases. Most often this device affects the stability of engine functioning. A more real reason lies in the clogging of the fuel filter. This node is located in the aggregate tank. If the trimmer for grass is used for more than two years, then it is necessary to check the filter, which may prevent fuel supply to the carburetor.

If the user is sure that the main problem lies in the cleansing element of the fuel, then you need to perform the following actions:

If the device has started quickly enough, then the problem lies in the fuel filter.

Long.term storage of fuel in the instrument.involved tank can significantly reduce the life of this node, as well as a random hit of fine debris and dust into a trimmer tank for grass. But if the filter is working, and the lawn mower still does not start, then you need to check the fuel hose. There are often situations when the hose together with the filter is disconnected from the trunk tube, which necessarily leads to the impossibility of starting the engine.

Production of candles: things that should not be done

The beginning of the new year always inspires people to start new projects, adhere to their New Year’s promises and develop what they may have already begun. If you are a beginner, we hope that your New Year solution was to make high.quality candles. If you have just started studying the manufacture of candles, you probably found that at times it could be caused.

Read Bour from a trimmer for grass with your own hands how to make

In this issue, we will use an unconventional approach and select some things that you should never do in the manufacture of candles if you plan to make the best candles from possible.Some of these bad methods can lead to the creation of a dangerous candle, while others will lead to not the best candle from possible. Some information that we are going to illuminate may seem like common sense if you have some experience in making candles, but for beginners this is not the case or they have not yet encountered our site.

The heating of the candle is facilitated by the use of heat-resistant motor oils for 4-stroke engines, a large wear of compression rings or the entire piston group as a whole.

How to look for malfunctions in the mechanical part

The transmission of rotation from an electric trimmer for grass is performed in the same way as models with an internal combustion engine: an integral shaft works inside the rectangular section of the bar, and a curved cable works.

Their length, diameter and design are selected by the manufacturer for specific dimensions of the composite bar.

Features of the junction of the composite bar

It is made by an adapter with a screw clamp.

The large screw head is made to conveniently adjust the position of the mowing organ at the bottom of the bar. The rotation angle is selected individually.

It is convenient for me to expose it so that the longitudinal axis of the protective casing and the axis of the electric motor are located in the same plane.

In this place, a malfunction associated with the transfer of torque from a direct shaft to a cable may sometimes occur in this place. It is manifested by the fact that at idle engine the trimmer for grass works normally, and already under a small load, the mowing head stops rotating.

The method of its elimination was well shown by the owner of the video “Repair of the Electrimmer” Roman Shapkov. I recommend to see.

Method of attaching a mowing head and a casing

On my trimmer from below the rod, the adapter is fixed with rivets, into which the fastener bolt of the protective casing will be plunged.

The output shaft of a rotating cable has a hexagon at the end. A plastic mowing head is put on it.

From the inside, a return spring of the automatic discharge of fishing line during kosbe is inserted into it.

A spool was inserted into it. It is fastened with a fixing nut from above.

The device of a spitter head with a fishing line is quite simple.

However, all plastic parts do not have high strength, subject to wear. Their working surfaces are erased. After three seasons of work on my trimmer, the output holes of the fishing line from the mowing head expanded, the thickness of the fixing nut decreased.

It is difficult to apply protective measures to wear, and repair of these parts is easiest to fully replace the head. It is easy to buy it: you just need to know the exact dimensions of the hexagon and evaluate the new design according to the working characteristics.

The secrets of the selection of fishing line

Among the frequent malfunctions of the trimmer coil, there are cases when the fishing line for the trimmer ended or simply confused due to improper winding on the spool. It is not difficult to eliminate them.

But in practice, I met with another defect in the fishing line, which was sold on the state retail network from its view in factory packaging.

As I understand it, it is specially hidden in a sealed package: you can not touch when buying.

When I opened the packaging to install the fishing line in the spool, its plasticity immediately caught my eye, and not elasticity. It is easily bending, behaves like a soft wire: when in contact with the grass, it immediately breaks. It is impossible to mow: she managed to return to the seller.

Since then, I have been buying only that fishing line for a trimmer that can be molested in my hands and evaluate its operational properties.

I try to refuse varieties of ordinary round fishing line. I prefer a ribbed shape to them with faces: asterisk, trapezoid, square or triangle. They are better cut off the grass.

If the trimmer for the grass does not start, we check the serviceability of the filters

You will need to resort to checking the air filter, through which the incoming air is cleaned into the carburetor. The clogging of the cleansing element leads to the fact that the air enters in a smaller quantity or its supply to the carburetor is completely stopped. Find out whether the air filter is the reason that the trimmer for the grass is not started is in a simple way:

• Remove the air filter and inspect it. The presence of clogging is already a reason to blame this detail in everything
• If there are no clogs visually, then you must try to start the motor without a filter. If a trimmer for grass starts without a filter, then it is definitely necessary to replace this part
• The air filter can be cleaned with a stream of compressed air, but if it has not changed for a long time, it is advisable to replace it with a new

It should be noted that a trimmer for grass can not start due to a blockage of an air filter, but these are extremely rare cases. Often, air filter clobs affect the stability of the engine, and also contribute to a decrease in performance.

It is interesting!If the chainsaw began without an air filter, then working as a tool without a filter element is contraindicated, since pollution will fall into the cylinder, and thereby the operational resource will decrease. The real reason why the gasoline trimmer for grass is not started is to clog the fuel filter. This part is located in the tank of the tool, and if the spit is already more than 2 years, then it is time to check the serviceability of the fuel element. If the filter is clogged, then the fuel mixture will not enter the carburetor accordingly, which means that the trimmer will not start the grass.

There are no difficulties with the replacement of the fuel filter, since for this it is enough to extract this part from the tank, and to replace it. If you are going to clean the fuel filter with a compressor, it is recommended to abandon this venture. It is better to buy a new filter for cleaning the fuel of the lawn mower, since clogs will still remain inside the old element. Below the video shows the process of replacing the fuel filter on the Oleo-Mac brand gasoline.

If you are not sure that the reason for the impossibility of launching a trimmer motor for grass is a cleansing element of fuel, then the following actions should be done:

• Remove the fuel filter
• Run the lawn mower
• If she got started, and quickly, then the problem is really in the fuel filter

The filter is clogged through the following reasons:

• With prolonged operation of the tool
• If low.quality gas or oil is used
• With prolonged storage of fuel in the tank of the tool
• If you pour fuel into the tank, which was stored for a long time
• When dust and small particles get into the tank of the tool. This usually happens during the tooling

It is interesting!If the fuel filter is working, and the lawn mower is not started, then it is worth making sure that the fuel hose is placed in the fuel. After all, there are times when the hose, along with the filter, is simply disconnected from the trunk tube, which leads to the impossibility of starting the engine engine.

Why the gasoline lawn mower does not start?

When your gasoline lawn mower does not start, first of all it is necessary to check the presence of fuel in the tank. If it is absent. share it to the desired level. Often, when the device is not used for a long time, gasoline is “exhausted”, so it must be completely drained and seasoned with new.

First, close the air damper completely, lifting the lever up, and then open, lowering the lever to the centimeter down. Fix three gas buttons. Pull the label of the starter and the engine starts up. Dress the lawn mower on the belt.

STIHL chainsaw stalls. does not develop momentum

All STIHL chainsaw systems function well, ensuring the launch of the mechanism. But sometimes, with confident work of idle, the saw does not gain revolutions at the load, interruptions begin in the motor. This means that there may be serious reasons requiring repair: to unbalance the carburetor screws, the end of the engine resource, breakdown of the candle or ignition coil, wear of the piston group.

But, most often, the engine does not develop turns, or may stall, when the check valve is out of order, a vacuum is created, which causes malfunctions. To repair the valve quite time.consuming, so it is better and faster to replace the oil tank cover, its cost is quite affordable.

Principle of operation

Carburetor. module of the power system, in which liquid fuel and air are mixed before supplying to the motor cylinders. Lawn mowed gasoline adjustment of the carburetor. Depending on the tool and the mode of its work, mixing and feed are adjustable in a suitable way.

The device of the carburetor of the lawn mower is monotonous in fact for all cases. Adjustment of the carburetor of the Chinese motorcycle. It belongs to the category of float devices. The latter provide constant characteristics of ready.made consistency.

• Air enters the body of a tube with an air damper. Lawn mowed Matrix Carburetor adjustment. The latter increases or reduces the air flow depending on its own position.
• On the site where a hole for supplying gasoline is formed, the tube has a narrowing. diffuser. Here the flow rate increases.
• Fuel from a float chamber through a jick is supplied to the tube. The level of the float determines the amount of fuel supplied. Because in the chamber the pressure is common, and in the tube is low due to greater air spare, then gasoline is absorbed through the nozzle.
• Accelerated air flow picks up fuel and spray it, forming a fuel mixture of suitable density.
• The mixture is absorbed into the cylinder through the pipeline.

The harder the air damper is open in the tube, the higher the density of the air flow, and, it means that more fuel enters the cylinder. Stiga gas mower. The tuning of the gas mushroom carburetor is reduced to the installation of such a ratio of the damper, in which the density of the fuel consistency becomes good.

Primary checks of the ignition system.

Ahead of time, before testing the ignition module, check the properity of the subsequent parts of the chain:

• Candles and switch
• The condition of the candle cap: should be tightly attached to the candle, the high.voltage wire is aggressively fixed and does not even fly out of the cap and coil, the matteral of the cap does not contain cracks
• The high.voltage wire is not damaged over the entire length, the contacts and connections of the wires are dense and do not even have traces of corrosion
• visually evaluate the absence of cracks and visible flaws on the reel body
• pollution of conductive parts and nodes remove
• By the ability, change refueling: you will like gasoline bad

The meaning of these actions is to exclude the elements of the chain from the list of probable defects to our client, not counting the coil. If our client remains in order to move on.

Most modern models of chainsaws and trimmers for grass do not require installation of ignition time. This angle is determined by the position of a special groove on the flywheel for the key groove to the crankshaft and magnets installed on one flywheel.

It is only necessary to correctly install the gap between the flywheel and the ignition coil. Depending on the model of the tool, the gap can be different. This is usually 0.2-0.4 mm. Since the flywheel is round, the usual automobile probe will not work for this purpose. It would be technically reasonable to expose the gap with a special template.

But it can not always be purchased. The acquisition of such an expensive template for one.time use is unreasonable. Instead of a corporate template, you can use a strip of plastic bottles of water. Cut the strip from the bottle in a place where there is no embossed embossing. Then the actions to install the clearance are approximately the same for the chainsaw and trimmers:

• Loosen the ignition fastening bolts.
• Direct the magnets on the flywheel to the ignition coil
• Clamping the flywheel between the flywheel and the coil, tighten the fasteners.
• Remove the strip
• Scroll the flywheel 360 degrees several times, making sure that it does not cling to the reel anywhere.

All. The gap between the coil and the flywheel is installed.

is impossible and impractical. Below is a list of ignition coils that can be purchased on our website

Denso

The Denso brand produces not only the spark plugs, the assortment is also full of oil filters, fuel pumps and many others. For many years, Denso has been steadily occupied by its leading position in the market. The company was founded in the distant 1949.

All the spark plugs are produced according to the quality standard, the products are constantly updated, which can please motorists. These Japanese candles were tested by time. during the testing of them, 18,000 km was passed. everything is fine.