The Oleo-Mac Sparta 25 law mower is not started
In order to adjust the carburetor itself, it is necessary to familiarize yourself with its device and remember the order of work that are performed to configure the parts responsible for the proper functioning of the constituent elements of the device and adjacent details. It is necessary to carefully handle objects to adjust the chainsaw system and determine the correspondence of the specified parameters as acceptable values.
The carburetor is used to mix the combustible mixture with air in these proportions. If the exact doses are not respected, the engine health is at risk. When a lot of air enters while the components are mixed and there is not enough fuel, such a mixture is considered “bad”.
You must not allow oversaturation, as well as malfunctions of the engine or wear of a large amount of fuel compared to air. The adjustment of the carburetor is necessary not only before the first use, but also if any deviations are detected in its work. Before you start working with a chainsaw, be sure to run it.
The design of the carburetor contains a standard set of elements, but may slightly differ depending on the manufacturer. Components:
- Fund. This is a special tube that visually resembles aerodynamic design. Air passes through it. In the transverse direction of the sash is located in the middle of the pipe. You can change your position. The more it pushes into the passage, the less air enters the engine.
- diffuser. This is the indicated part of the tube. Increases the speed of air supply in the segment, where the fuel comes.
- Fuel supply channels. The fuel mixture is found in a float chamber, then passes into the nozzle, from which it enters the nozzle.
- Float chamber. This is a separate constructive element that resembles the shape of the tank. Designed to maintain the optimal level of fuel fluid before entering the duct from which air comes.
Do not know which chainsaw to choose? Read our article.
Looking for cheaper, but reliable and time.tested models? Pay attention to the chainsaws of production.
Or research of foreign manufacturers of chainsaws such as Calm.
What is needed in order to set up and set up a chainsaw yourself
Each owner of the carburetor must have the necessary tools to configure this system. Three adjusting screws are located on the device. They have their own marking:
- L. screw for correction of low speed.
- H. screw for high.speed adjustment.
- T. regulates idle work, in most cases it is used for experiments.
Before setting up the carburetor, you need to prepare the device:
- The engine warms up, t.e. starts about 10 minutes before the repair, and is disconnected when starting work (see., How to start a chainsaw).
- Air filter is checked and washed.
- The chain stops, turning the screw t to the end (see. Chain oil).
For safe repair, prepare an even surface on which you can carefully place the device and unscrew the chain in the opposite direction. Tachometer is required. He detects a malfunction in a carburetor. When turning the screws, the sound should be perfect and absolutely even. If the creaky notes are noticed, the mixture is oversaturated.
The Oleo-Mac Sparta 250s lawn mower is not started
The overall adjustment of the maximum revolutions, engine power, temperature and gas consumption depends on the left screw (H). Spare parts for motorcycles OLEO-MAC The Oleo-Mac Sparta 250S repair of carburetor.
Adjustment of the lawn mower carburetor can be adjusted with your own hands, as well as the entire bench tool for the garden, is not difficult to maintain equipment. Repair, configure without the help of others there is an option and it is necessary. For example, adjusting the carburetor of the lawn mower on their own. it is 5 minutes. In general, the essence of the problem of the Oleo-Mac Sparta 37 is that after cleaning the silencer, the braid braid stopped gaining momentum.
Oleo-Mac Sparta 44 Examination adjustment
Simply put, adjusting the carburetor on a benzocos. creating an optimal fuel mixture due to the correct air supply. This happens when, instead of normal repair, the “symptoms” are muffled by setting a carburetor.
Adjustment of the lawn mower carburetor can be adjusted with your own hands, like the entire benzo tool for the garden, is not difficult to maintain equipment. Repair, configure without the help of others you can and necessary. For example, adjusting the carburetor of the lawn mower with your own hands. it is 5 minutes. Spare parts for motorcycle. Repair and adjustment of the carburetor motorcosa.
Oleo-Mac Sparta 37 problems are not gaining momentum!
The usual work of braids with internal combustion and possibly disturbed due to the getting of the dirt in the exhaust channel or clogging of the muffler grid. There is such an inconsistency on the models of the older generation. Solve the issue of course by classical cleaning and removal of the anti.icing grid.
If the step.by.step method of searching for a malfunction did not give a result, and your braid for grass as before does not start or stalls, it is worth looking at the carburetor and the engine itself. The clogged carburetor will be the main reason, unbalanced operation of the tool. There are three main tasks here:
- Clogging of channels or nozzles. The entire aggregate is cleaned with special flushing or blown by a strong stream of air of high pressure from the compressor. Do not use needles and wire, so there are variations to be damaged by passing sections;
- Wear of the carburetor laying. Output is a change of laying out;
- Violation of density. To check this indicator, use a common domestic tonometer, replacing it with a deceased. Look for the testimony: if they do not change, our client remains perfectly, and since the pressure will begin to fall, it means that some part of the carburetor is faulty. Will have to find it and replace the latest.
If our client remains in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips are detected, scratches in other words of Zadirov, on the piston on another cylinder they should be replaced. Piston rings are subject to inseparable verification. A small piston owl when swaying the connecting rod shows that the time has come to change the rings. This function is best entrusted to the specialists of the service center.
So that the lawn mower is perfectly started and henceforth, it is necessary to provide it with excellent storage and operation conditions:
Oleo-Mac Sparta 25. The next repair of a seven.year.old lawn mower
- At one time, look closely behind the cooling system, painstakingly and fit clean the channels in the housing, additionally the starter ribs;
- If necessary, use solvents, kerosene and other cleaning products for cleaning;
- Do not clean the “hot” tool. let it cool;
- Be sure to make the requirements of the annotation for the operating mode, it is different to overheat the engine;
- If you do not plan to use the lawn mower in the near month, the fuel mixture from it must be drained, t. to. Over time, it breaks up into languid fractions, which will definitely score the channels of the carburetor;
- After draining fuel, let the trimmer work at idle until it stalls, this will help to completely remove the remains of the working consistency.
Before winter storage, take subsequent steps:
- Disassemble the braid for one hundred percent, wash and clean our client the details remain, which you can;
- Inspect the details for damage, if necessary, droop distortions, impulses, bent and any other malfunctions;
- Pour a sufficient amount of oil into the gearbox and clean the air filter;
- There is a partly option to disassemble the motor, wash, blow and smear what remains to our client mobile parts;
- If you want to be to lubricate the piston, you need to turn the candle, raise the piston with the last dead point by the starter, pour a small oil into the candle hole and scroll the crankshaft several times;
- If you store the lawn mower not in your house, wrap the engine with an oiled rag.
Remember, thorough compliance with the rules may be blurred that the lawn mower is badly starting over several seasons.
The main malfunctions of the starter of the trimmer for grass
It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:
These details are shown in the photo below.
It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.
Removing and disassembling the starter, replacing broken parts
To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.
Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.
Parsing the starting node
They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:
- spin a screw with a screwdriver, fixing the pulley with a starter lid;
- take out a spring and antennae;
- Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
- determine why the launch mechanism has broken;
- If the spring collapses almost completely, then it is replaced;
- When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);
Removing and disassembling the starter, replacing broken parts
To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.
Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.
Parsing the starting node
They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:
- spin a screw with a screwdriver, fixing the pulley with a starter lid;
- take out a spring and antennae;
- Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
- determine why the launch mechanism has broken;
- If the spring collapses almost completely, then it is replaced;
- When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);
List of Oleo-Mac gasoline trimmers:
SPARTA 25TR EKO, Multimate Euro2, Sparta 25s Disk, Sparta 25, Sparta 25he, Multimate Euro2, Sparta 25 Luxe, 725D, 725S Ergo, BC 24 T EURO 1, Sparta 25D, Sparta 37, 725T ERGO, SPARTA, SPARTA, SPARTA 38, 725T ERGO, SPARTA, SPARTA, SPARTA 38, 725TE 44, 735T, Sparta 42BP, 446BP ERGO, BC260 4s, 440BP, 746T, 740T, BC 420 T, BC 430 T, BC360 4T, 753T, 753TS, BCF 430
Our service center takes only gasoline trimmers for OLEO-MAC grass for repair. We do not repair electric trimmers for grass!
Attention! Before contacting the service center!
We ask you to inform the manager of our company in advance: the exact model of equipment. If you need spare parts for a gasoline trimmer for Oleo-Mac grass, you need to know: the brand of your engine; engine model; type of; The code located at the installation site of the carburetor, the spark plugs or muffler. The engine code is indicated by a line consisting of 3 groups (in each line 6-signs without additional quotes and stars).
Oleo Mac sparta 25 fűkasza szervízelése.
The lawn mower is not started? Eliminate the most common reason
Chinese motorcycles headache for the owner, but still without them nowhere. The main problem is the difficulty of starting after a long downtime. If the lawn mower worked as a clock in the fall, but it does not start in the spring, then you must most likely disassemble the carburetor and clean its valve.
Necessary tools:
If the motor motorcycles refuses to start, then first of all you need to check the candle. If it is completely dry, then this means that the fuel is not supplied to the combustion chamber and the reason is in the carburetor. Immediately it is worth checking the candle and for the subject of a spark in order to exclude it from the reasons on all fronts.
You can also make sure that the motor itself is serviceable. To do this, having twisted the candle, you need to pour a syringe into a combustion chamber of several milliliters of gasoline. After this, the candle is twisted and the lawn mower is started. If everything is in order with the motor, then it will work for a few seconds. This will once again confirm that it makes sense to disassemble the carburetor.
Next, a plastic protective cover is removed along with an air filter. After that, 2 screws are twisted with a cross.shaped screwdriver, holding the air damper and the carburetor on the engine. Fuel tubes immediately break down.
From the side of the cap of the suction, you need to twist 4 screws with a screwdriver, and divide it into 2 halves. We are interested in half with suction. There is a valve from its inside in the center.
He often sticks out, because after evaporation of gasoline, with a simple on it, a viscous oil works as glue. To check it, you need to put a short thin tube and try to blow the air through it. If he is stuck, he will not be able to blow out in any direction.
Caliping of the valve is eliminated by a conventional match. Toothpicks are better not to use, since they are sharp and can harm. A match must be slightly rested on the valve and stir it. After cleaning the match, it will be blown up.
Oleo Mac Sparta 250T. repair (part 1)
Fuel will be able to act, so it will work. Cleaning the valve is not a panacea for all motorcycles that do not start after downtime, but this helps in 8 cases out of 10. The remaining 20%, as a rule, are also associated with a carburetor, usually with a needle.
Use actual promotional codes to buy cheaper!
-Oleo-Mac Sparta 25 can be bought much cheaper. Cashback sometimes reaches 17%, but they do not like to talk about it. To get it, choose a store, choose a store where the price is below and activate the cashback, then make a purchase in the store as usual, the cashback will come within 10 minutes. Cashback is not points and bonuses, but real money that can be transferred to your card or phone balance. A pleasant discount will not be superfluous! We give us the first cashback 150r on promotional codes: SDX548 Select a store and activate cashback you need: 770 stores with cashback
– 2. Divasrok
| Pros: | It looks comfortable and compact. |
| Minuses: | Accurate mixing of oil, strong vibration, weak fastenings (quickly weaken, it is constant to sweat. |
| Review: | on the window I liked her.But at home, when he started by all the rules (tormented of course) felt vibration.The service was told to pull up all the bolts and nuts.Pulled up.The vibration has decreased.He began to mow.It seems to be nothing, only wraps nettle, it will have.Having risen hundreds of hundred and a half, I felt fatigue from vibration.put a knife, vibration even more.With grief in half, he shaved his 4 acres.I started again a month later.Barely started.He began to mow a fishing line.I wound the grass again, something blinked and stalled.Bring more weaknesses.He spat on the grass.She is and high beautiful. |
– 2. The data is hidden
| Pros: | Light, comfortable. |
| Minuses: | Not very maintainable. |
| Review: | I worked out two seasons, the third began to overwhelm the carburetor. pouring ka from a bucket, a starter covered, and in order to correct it half a braid for grass, you need to disassemble it. |
– 2. Igoshin Yaroslav
| Pros: | Light. It copes well with any kind of fine vegetation (grass, burdock, rhubarb, with fishing lines small shrubs, with a knife. Shrubs up to 5 cm in diameter), economical fuel consumption (an average of 1 gas station per plot of 10 acres). |
| Minuses: | Quality of elements, high cost of spare parts. |
| Review: | In general, the model is quite good, but spare parts for it are unreasonably expensive, and finding them is not so easy. He worked only 2.5 years and scratched the cylinder and piston (are not subject to restoration), failed the crankshaft and burst the crankshaft bearing. As a result, repairs (in the service center along with spare parts) will cost more than half the cost of a trimmer for grass. |
– 2. Ivan
| Pros: | Quality tool |
| Minuses: | They sent the wrong model, I ordered Sparta 25, but sent Sparta Aluminum. |
| Review: | I understand that the difference in functionality does not, but still not pleasant when there is one product in the photo and description, but in fact another. And there is no warranty coupon yet. |
– 2. A79657774484
| Pros: | Everything is made of metal and not from plastic. It looks reliable. I will supplement: bought in the LLC of the Civil Code of the Empire of the Instrument, address: g. st. Friedrich Engels, D. 58 p. 3rd floor 2 office 326 through Yandex Market. After 3 launches, the starter stopped working. And this is on a spit out of the box. Services from the estate-moto manor for Dimitrov in St. Petersburg were off-howled with repair in Murino. Let’s see how to fix it. If it breaks again. I will hand over and buy Khuskvarna, let them return the money |
| Minuses: | Bought in the LLC of the Civil Code of the Empire of the Instrument, address: g. st. Friedrich Engels, D. 58 p. 3rd floor 2 office 326. The praised starter of the trimmer for the grass stopped starting the engine after three launches. I called in 2 services, in one it was said that only after the guarantee was repaired, the second took after a long swearing. In general, I radically changed the opinion of this trimmer for grass in the negative side. The other day I will take it to repair it under the warranty. |
| Review: | Bought in the LLC of the Civil Code of the Empire of the Instrument, address: g. st. Friedrich Engels, D. 58 p. 3rd floor 2 office 326 after three launches ceased to start with a starter. I regret to buy, I plan to change it to Khuskvarna |
– one. Mironov Sergey
| Pros: | Not |
| Minuses: | I bought the 2nd scoop of the Daana brand, the 1st worked for 3 seasons with coverage of the plot of 25 acres with a cloth 3-4 times a year, the problems began in the 3rd season-item of the gear of the drive under the editor, interruptions at launch, loss of power, I am to the service, I have the price of repair 6t.R. New 11t.R. Probably not high.quality oil lily. OK.I took the 2nd. For the 2th season, the same problems except the gearbox. I’m going to buy Stihl!! There is not enough power with high grass, which affects the time of the trench of the site, the quality really disappointed. |
| Review: | – |
– one. Hizriev Arseny
| Pros: | a light weight |
| Minuses: | Large vibration, small power, there is no canister for mixing fuel and other additional instruments, an uncomfortable suspension system, a terribly unattended center of gravity, a dumb disk, an uncomfortable handle, a large volume and a lot of different inconvenience during operation is. |
| Review: | I came to buy Echo, but the seller said take it, I have the same very pleased. In the end, having come home barely started. Friendship in the wood of the grandfather and then better started up. There is not enough power even in rare grass, voracious like KAMAZ. at work echo eats ten times less. After the kosba, the hands were buzzing all day and there was a ringing in the ears (I thought the membranes burst) be sure to dress the headphones. in general grief, not a braid for grass. Probably Italians were developing after binge. it is better to tear the grass with your hands, the same health will not suffer. |
Advantages and disadvantages
The main advantages of Oleo-Mac chainsaw carburetors:
- Large resource;
- Small sizes;
- Three adjustment screws allowing to make accurate setting (a feature of all modern chainsaws with membrane carburetors)
- Small sizes and puzdo are small mass of the structure, for comparison with analogues;
- Available price of parts, carburetor assembly;
- Unpretentiousness to the quality of gasoline.
It is also necessary to note a number of shortcomings:
- It can be difficult to find a repair kit on sale, in small towns;
- Difficulties with options, the highest requirements for the qualifications of settings;
- The need for repeated adjustments for long.term operation.
Oleo-Mac 947 chainsaw. Characteristics of the model
The advantages of this semi.professional portable saw. Low vibration, a small center of mass and the highest performance in all weather criteria.
The piston of the gasoline engine of this model is made of forged steel and equipped with 2 rings to increase the resistance of the element.
The saws of this semi-professional OLEO-MAC model consist of a forged circuit installed on the iron railway. The headset is lubricated by automatic and controlled by an adjustable oil pump.
The characteristics of the signature file contain:
- The factory power of the motor is 3.1 liters. From.;
- Fuel tank capacity / oil tank. 500/270 ml
- Recommended tire length for a suspended tire. 45 cm;
- The weight. 5.6 kg.
Read how to adjust the carburetor of the Chinese chainsaw
The internal components of this OLEO-MAC are located in a shockproof case, Yaki withstands long heating, vibration and low height.
Oleo-Mac Sparta 25 carburetor adjustment
Oleo-Mac Sparta 25
- Power / volume. 1.0 l.FROM. 0.8 kW / 25.4 cm³
- Tap Go head. 2.40 mm (130mm)
- Knife diameter. 255 mm with 3 blades
- Dry weight. 6.2 kg
SPARTA 25 Detailing SPARTA 25 Details 25
OLEO-MAC SPARTA 25 BASS with the highest performance indicators, properties and ergonomics. Namely, it is hunting to note the fact that the installation of additional bearings, also a joint connection of the motor and working shaft, ensured a significant decrease in vibration, which could not but affect the performance and quality of labor. To hold motorcycles, a paraphernalic belt is used to control the process, a paired bicycle handle is provided. The Oleo-Mac Sparta 25 model takes into account all the Комментарии и мнения владельцев from the predecessors, and specifically. A primer is installed for pumping fuel and a system of lightweight starting was implemented. Apart from this, the clutch clutch is improved, which allowed to significantly reduce the load on the working shaft. The standard includes a mowing head with automatic fishing for fishing line, 3 huts and a protective screen that prevents the release of branches and grass to the side.
The most powerful and reliable engine (1 liter.FROM. / 0.8 kW). Small.sized and light engine with a nickel shiny cylinder (rice.one). Crankshaft and tarnished steel connecting rod. Electric ignition guarantees the highest performance, light start and long service life (rice.one). SPARTA 25 Kustorez is simple for starting even for the least experienced user. The presence of “primer” (“a” rice.2), which recalls the mixture of the carburetor, allows you to start working with a smaller effort (rice.2). Easy access and air filter service: the operation does not ask for the use of tools, but is carried out by pressing a comfortable latch of the spark plug, regardless of protection to prevent breakdown from the impact, is in sight: only the ignition candle key is required for cleaning and replacement. A large tank for fuel consistency allows autonomy for a long time and just the lawn mower complies with the current rules: the ergonomic handle connects all the control elements: the lever of the throttle, the launch switch and the stop (rice.5), have an accelerator blocking security system (“b” rice.4) which warns random acceleration. Centrifugal clutch with sliding blocks, covered with antifriction material, is designed to withstand long working conditions (rice.5). Transmitting a tube (Ø26 for Sparta25), one hundred percent durable, guarantees good resistance to a small mass. The fuel tank is protected from random clashes (“c” rice.6). Reducing vibrations to a minimum thanks to:. 5 self.lubricated bushings placed by snutri transmission tubes (“D” rice.7). Anti.Vibration on the motor cover. Anti.vibration on the support of the steering wheel handle (only Sparta25) “E” rice.8) flexible shaft of boxes (Sparta 25tr) made of steel with a special shell along the entire length (“f” rice.9) warns annoying vibrations from the operator and increases the service life of the machine. The adoption of a transparent reservoir simplifies the visualization of the level of fuel. On the handle there is also a mount for the wire harness (function for Sparta25TR).
| Number in the diagram | Article of the details | Name |
| one | 3960067ar | Fastener screw for motor skoses Oleo-Mac Sparta 25, EFCO Stark 25 |
| 2 | 4161570R | Engine block assembly for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 3 | 4098683r | The puck of the crankshaft for the Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| four | 4160026R | Piston Pull for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 5 | 3819006r | Stop puck for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 6 | 3801015R | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 7 | 61010001R | Oleo-Mac Sparta 25, EFCO Stark 25 Motokos |
| eight | 3916005R | Washer for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 9 | 61010005 | Muffler cover for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| ten | 3806028 | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| eleven | 4095211R | Muffler fastening for Motokosa Oleo-Mac Sparta 25, Efco Stark 25 |
| 12 | 61010011 | Molushter gasket for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 13 | 072700048R | Piston Ring for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| fourteen | 3801010R | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| fifteen | 4160025R | Stop finger ring for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 16 | 4161030B | Piston included for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 17 | 3055101 | Spark plug for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| eighteen | 4098232R | Kolenval Oleo-Mac SPARTA 25, EFCO Stark 25 Motokos |
| 19 | 3064005ar | The puck of the crankshaft for the Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| twenty | 3024010R | Stop Ring for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 21 | 3037026R | Kolenval I needle crankshaft for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 22 | 4161599R | Cornflower for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 23 | 4160479R | Kolenlval for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 24 | 61010012R | Motokos motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 25 | 3034003r | Kolenlval bearing for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 26 | 3025019 | Stop puck for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 27 | 3035023R | Kolenlval bearing for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 28 | 4160124R | Washer for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 29 | 3050030r | Crankshaft oil seal for Oleo-Mac Sparta 25, Efco Stark 25 |
Advantages and disadvantages
The main advantages of Oleo-Mac chainsaw carburetors:
- Large resource;
- Small sizes;
- Three adjustment screws allowing to make accurate setting (a feature of all modern chainsaws with membrane carburetors)
- Small sizes and puzdo are small mass of the structure, for comparison with analogues;
- Available price of parts, carburetor assembly;
- Unpretentiousness to the quality of gasoline.
It is also necessary to note a number of shortcomings:
- It can be difficult to find a repair kit on sale, in small towns;
- Difficulties with options, the highest requirements for the qualifications of settings;
- The need for repeated adjustments for long.term operation.
Oleo-Mac 947 chainsaw. Characteristics of the model
The advantages of this semi.professional portable saw. Low vibration, a small center of mass and the highest performance in all weather criteria.
The piston of the gasoline engine of this model is made of forged steel and equipped with 2 rings to increase the resistance of the element.
The saws of this semi-professional OLEO-MAC model consist of a forged circuit installed on the iron railway. The headset is lubricated by automatic and controlled by an adjustable oil pump.
The characteristics of the signature file contain:
- The factory power of the motor is 3.1 liters. From.;
- Fuel tank capacity / oil tank. 500/270 ml
- Recommended tire length for a suspended tire. 45 cm;
- The weight. 5.6 kg.
Read how to adjust the carburetor of the Chinese chainsaw
The internal components of this OLEO-MAC are located in a shockproof case, Yaki withstands long heating, vibration and low height.
Oleo-Mac Sparta 25 carburetor adjustment
Oleo-Mac Sparta 25
- Power / volume. 1.0 l.FROM. 0.8 kW / 25.4 cm³
- Tap Go head. 2.40 mm (130mm)
- Knife diameter. 255 mm with 3 blades
- Dry weight. 6.2 kg
SPARTA 25 Detailing SPARTA 25 Details 25
OLEO-MAC SPARTA 25 BASS with the highest performance indicators, properties and ergonomics. Namely, it is hunting to note the fact that the installation of additional bearings, also a joint connection of the motor and working shaft, ensured a significant decrease in vibration, which could not but affect the performance and quality of labor. To hold motorcycles, a paraphernalic belt is used to control the process, a paired bicycle handle is provided. The Oleo-Mac Sparta 25 model takes into account all the Комментарии и мнения владельцев from the predecessors, and specifically. A primer is installed for pumping fuel and a system of lightweight starting was implemented. Apart from this, the clutch clutch is improved, which allowed to significantly reduce the load on the working shaft. The standard includes a mowing head with automatic fishing for fishing line, 3 huts and a protective screen that prevents the release of branches and grass to the side.
The most powerful and reliable engine (1 liter.FROM. / 0.8 kW). Small.sized and light engine with a nickel shiny cylinder (rice.one). Crankshaft and tarnished steel connecting rod. Electric ignition guarantees the highest performance, light start and long service life (rice.one). SPARTA 25 Kustorez is simple for starting even for the least experienced user. The presence of “primer” (“a” rice.2), which recalls the mixture of the carburetor, allows you to start working with a smaller effort (rice.2). Easy access and air filter service: the operation does not ask for the use of tools, but is carried out by pressing a comfortable latch of the spark plug, regardless of protection to prevent breakdown from the impact, is in sight: only the ignition candle key is required for cleaning and replacement. A large tank for fuel consistency allows autonomy for a long time and just the lawn mower complies with the current rules: the ergonomic handle connects all the control elements: the lever of the throttle, the launch switch and the stop (rice.5), have an accelerator blocking security system (“b” rice.4) which warns random acceleration. Centrifugal clutch with sliding blocks, covered with antifriction material, is designed to withstand long working conditions (rice.5). Transmitting a tube (Ø26 for Sparta25), one hundred percent durable, guarantees good resistance to a small mass. The fuel tank is protected from random clashes (“c” rice.6). Reducing vibrations to a minimum thanks to:. 5 self.lubricated bushings placed by snutri transmission tubes (“D” rice.7). Anti.Vibration on the motor cover. Anti.vibration on the support of the steering wheel handle (only Sparta25) “E” rice.8) flexible shaft of boxes (Sparta 25tr) made of steel with a special shell along the entire length (“f” rice.9) warns annoying vibrations from the operator and increases the service life of the machine. The adoption of a transparent reservoir simplifies the visualization of the level of fuel. On the handle there is also a mount for the wire harness (function for Sparta25TR).
| Number in the diagram | Article of the details | Name |
| one | 3960067ar | Fastener screw for motor skoses Oleo-Mac Sparta 25, EFCO Stark 25 |
| 2 | 4161570R | Engine block assembly for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 3 | 4098683r | The puck of the crankshaft for the Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| four | 4160026R | Piston Pull for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 5 | 3819006r | Stop puck for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 6 | 3801015R | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 7 | 61010001R | Oleo-Mac Sparta 25, EFCO Stark 25 Motokos |
| eight | 3916005R | Washer for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 9 | 61010005 | Muffler cover for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| ten | 3806028 | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| eleven | 4095211R | Muffler fastening for Motokosa Oleo-Mac Sparta 25, Efco Stark 25 |
| 12 | 61010011 | Molushter gasket for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 13 | 072700048R | Piston Ring for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| fourteen | 3801010R | Screw for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| fifteen | 4160025R | Stop finger ring for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 16 | 4161030B | Piston included for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 17 | 3055101 | Spark plug for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| eighteen | 4098232R | Kolenval Oleo-Mac SPARTA 25, EFCO Stark 25 Motokos |
| 19 | 3064005ar | The puck of the crankshaft for the Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| twenty | 3024010R | Stop Ring for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 21 | 3037026R | Kolenval I needle crankshaft for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 22 | 4161599R | Cornflower for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 23 | 4160479R | Kolenlval for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 24 | 61010012R | Motokos motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 25 | 3034003r | Kolenlval bearing for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 26 | 3025019 | Stop puck for Motokos OLEO-MAC SPARTA 25, EFCO Stark 25 |
| 27 | 3035023R | Kolenlval bearing for Motokos Oleo-Mac Sparta 25, Efco Stark 25 |
| 28 | 4160124R | Washer for Motokos Oleo-Mac Sparta 25, EFCO Stark 25 |
| 29 | 3050030r | Crankshaft oil seal for Oleo-Mac Sparta 25, Efco Stark 25 |