Which Hacksaw Is Better To Cut Chipboard

How and with what to cut the laminate. The choice of tools and the nuances of sawing laminated flooring When laying laminate, you cannot do without cutting some of the boards. And here is how to cut the laminate so that chipping and chips do not work. There are several ways, but not all of them will give the perfect cut.

How to saw with an electric jigsaw without chips

It is good if you have a jigsaw at home equipped with a file for wooden surfaces.

which hacksaw is better to cut chipboard

Before sawing, mark the cut line with a pencil, and then cut through the film of the laminated coating with a knife or awl. Now grip the board tightly (face down).

The speed of the power tool must be high. You must try to cut smoothly enough, without jerking the jigsaw, so that no chips occur. Having got used to it, it is possible to quickly and accurately saw laminate boards. over, an excellent result is obtained when sawing both along and across the board. It seems that the answer to the question, the better to cut the laminate, is clear. Of course a jigsaw.

We pick up a hacksaw

Laminate hacksaw, of course, sawn, but it is not very suitable for such work. After all, the teeth of a hacksaw, designed for woodworking, are intimidatingly large, and the top film of the floor covering is so thin. That and look, there will be ugly marks from these teeth. And it’s hard to cut the pressed laminate structure with a hacksaw. Hands get tired.

To get a better result, arm yourself with a fine-toothed hacksaw. For example, a hacksaw designed for cutting metal may well work. Chips on the cut can be avoided, but cutting with a fine-toothed hacksaw will be more difficult than a tool for woodworking. However, if you do not intend to cut the laminate in large quantities, then this method is fine. The quality of the cut, of course, is not perfect, but quite tolerable.

And here are the promised little tricks: before you cut, stick a piece of masking tape on this place. If you do this, then no chips are formed at the cut site. over, the laminate board must be laid face up. And in order for the cut to be smooth and clean, the hacksaw must have fine, frequent teeth.

Since the laminate is pressed using special mechanisms, then, naturally, it is better to saw it not by hand, but with an electric tool.

For example, an electric hoe (reciprocating saw) is quite suitable for this, which is increasingly used by home craftsmen.

A circular saw takes experience

You can also cut the laminate with a circular saw, equipping it with a disc for metal work. At the same time, we put the board prepared for cutting and marked out on some flat plane. The laminated film should not be on the bottom, as with a jigsaw, but on the top. Slowly and smoothly moving the circular disc along the mowing line of the cut, we get an even and high-quality cutting surface. During operation, the disc does not get stuck in the laminate.

But for those who have never taken such an instrument in their hands, it will be difficult for habit. It takes a lot of effort and effort to achieve the desired result. Having acquired the skill over time, it will be possible to saw the laminate very quickly and efficiently. But this process requires patience.

If you have not previously sawed other materials with this tool, then it is better to give preference to a jigsaw.

It is good if you have a jigsaw at home equipped with a file for wooden surfaces.

Using this tool is the best option.

Before sawing, mark the cut line with a pencil, and then cut through the film of the laminated coating with a knife or awl. Now grip the board tightly (face down).

The speed of the power tool must be high. You must try to cut smoothly enough, without jerking the jigsaw, so that no chips occur. Having got used to it, it is possible to quickly and accurately saw laminate boards. over, an excellent result is obtained when sawing both along and across the board. It seems that the answer to the question, the better to cut the laminate, is clear. Of course a jigsaw.

How and with what to cut the laminate. Choice of tools and nuances of sawing laminated coatings

Laminate flooring has come to the liking of many, this inexpensive floor material is very practical and beautiful. But not everyone succeeds in carefully sawing off even pieces from it. And you will have to cut, and repeatedly at the end of each row, at least. So how and with what to cut the laminate so that the cut line is pleasing to the eye. Consider the methods and tools that can be used to cut the laminate.

How to cut chipboard without chips.

We recently bought a coffee table, the price is inexpensive, but there is a but. The height of the table for our interior is too big. It would be nice to reduce the height by 10 centimeters. As they say, we are not looking for easy ways, I decided that

I can do it myself.

I remembered that on our site there is an asoleg specialist who made a computer desk with his own hands, of course, I am far from him, but some recommendations can help. I contacted him, explained the problem and he kindly shared his secret. With his permission, I publish his technology for cutting furniture chipboard without chips.

Everything turned out to be corny and simple. We mark the cutting line. Then, with a clerical knife, along a ruler, cut through the top layer of chipboard. Just run the knife several times with little effort along the mowing line of the cut. (I recommend practicing on the unnecessary part of the chipboard) If you press very hard, the decorative layer will begin to swell and turn out not very nice.

Further, retreating 1-2 millimeters from the intended mowing line towards the rough part, cut it with a jigsaw or a suitable file with teeth directed to the saw handle. We make a wash down on the opposite side of the cut so that there is no chipping at the end of the cut. And we saw through to the end. You need to cut carefully, slowly. Then, with a medium grain sandpaper, fixed on a bar, we clean the end of the part. If necessary, remove the millimeter that we retreated. My cut turned out to be almost perfect, after processing with sandpaper there were no scoring at all. The photo shows the difference between the left and right sides of the cut. Well, and, accordingly, if both parts of the chipboard are needed, we cut it with a knife on both sides of the cut. We measure the thickness of the cut of a jigsaw or file, add 2 millimeters. The result is the distance that should be between the slots made with a clerical knife. Cut exactly between these lines. Then there will be no scuffs on the other side. Naturally you need to use a sharp tool, I use a tool sharpening machine.

Everything worked out great. On the finished table, my wife did not find the place where I cut.

Thanks for the assistance and help asoleg.

Tags: How to cut chipboard without chips, how to cut chipboard without chips.

This article is found by the words:

  • How to saw off chipboard without chips
  • How to cut chipboard without chips
  • How to cut chipboard without
  • How to saw chipboard without chips with a jigsaw
  • How to cut wood chipboard without chips at home
  • How to cut wood chipboard without chips at home
  • How to cut a chipboard without chips
  • How to cut a chipboard without chips
  • How to cut the chipboard
  • How to cut chipboard without chips

If you love doing something with your own hands, read the article. Hair dryer construction, methods of application

Methods for cutting chipboard without chips

You can saw on a panel saw. But its cost starts from 50,000 and reaches 1,000,000 rubles. If you need to cut the chipboard to make several pieces of furniture for yourself, other methods are more suitable.

Manufacturing

Manufacturing begins with the main components and ends with smaller ones.

Stages of making a machine for cutting chipboard with your own hands:

  1. Manufacturing of the bed. Square or round pipes are required. They are cut and fastened to each other with clamps. After checking the dimensions and correct positioning of the components, weld.
  2. Manufacturing of a movable carriage. Install guides, best of all, a beam or two circular pipes connected to each other. The carriage must be equipped with rollers for smooth sliding.
  3. Making a desktop. The base is made of steel sheet with a thickness of at least three millimeters, the working surface is made of chipboard sheet, measuring rulers are attached to it.
  4. Production of clamps for sheets, for example, from a lever mechanism of any configuration.
  5. At the end, the cutting unit is connected to the chip suction unit.

The quality of finished products produced on machines of our own manufacture is higher than that of products created entirely by hand tools, but still lower than on industrial machines.

Required tools and materials

The saw unit of the machine is most often a welded structure, since it most effectively resists vibration.

  • Welding machine;
  • Angle grinder with disc for metal;
  • Electric drill;
  • Measuring tool.

In order for the equipment to work for several years, it is better to choose those materials for its manufacture that have been subjected to heat treatment.

  • Square or round pipes;
  • A beam or two pipes of circular cross section, interconnected;
  • Videos;
  • Steel sheet with a thickness of at least three millimeters;
  • Chipboard sheet;
  • Lever mechanism of any configuration.

How to cut chipboard without chips?

Before starting to cut chipboard, especially laminated chipboard, cut the line with a sharp tool, along which we will cut and glue paper tape with a sticky layer along it. This will help to minimize damage to the decorative chipboard layer.

If chips still could not be avoided, we process the cut first with a file, working from the edges to the center, and then with a fine-grained sandpaper. It is also possible to mask all defects by using a flexible profile where possible.

Sawing chipboard methods and methods of processing

[contents] If you have tried to cut chipboard at home at least once, then you know for sure that this work is by no means simple and requires not only skill, but also a good tool. Laminated chipboard is especially difficult to process, when sawing it often produces a lot of chips. That is why many craftsmen, faced with such a problem, come to the conclusion that it is better to cut the chipboard when buying, especially since many trading organizations provide such services and the price for them is quite acceptable.

Sawing of chipboard is carried out using precise panel saws, which will help to obtain blanks of a given size and shape.

In addition to cutting sheets, they will help you to calculate and provide in the form of a visual file several options for competent and economical cutting of sheet material (using special computer programs) and, if necessary, perform edging. However, if for some reason you prefer to do this work yourself, you will have to do some preparatory work before sawing the chipboard.

  1. Tools and materials
  2. How to cut chipboard without chips?
  3. Figured cutting
  4. What you can’t cut chipboard

Figured cutting

It is even more difficult to obtain curved surfaces of a given configuration at home, while you will have to additionally spend money on purchasing a router, which will help you get rid of chips and notches formed when you cut chipboard.

To cut chipboard, you need to follow these steps:

  1. Having marked out the contours of the necessary part on the chipboard sheet, we cut it out with an electric jigsaw, trying to cut, retreating only a couple of millimeters from the intended mowing line of the cut;
  2. We make templates of the design radius from fiberboard or plywood and carefully grind the ends with sandpaper;
  3. Attaching the template to the part to be trimmed, clamp it with clamps and process it with a manual copying cutter with a bearing, removing excess material exactly to the intended mowing line.

It does not matter which cutter (with two or four knives used). The only condition is that the knives must grasp the cut thickness being processed along the entire height. After processing, it remains only to stick the edge on the part. How this is done look at: