Cord -dressing in a trimmer head without disassembly. Starters for lawn mower: device…

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

How to Easily Load Speed Feed Trimmer Line

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

Reviews about trimmer for grass gasoline hopper farmer-052

Advantages: powerful, comfortable in hand, not heavy.

Disadvantages: the quality is terrible. During the year of operation, the piston was changed twice, four times the starter. Constant problems with carburetor. In short, they repaired more than worked.

Comment: I will not advise anyone hoper. Before that, Interskol was (and stayed). worked and works at all without problems. We decided to take something ramps and really regretted it.

Advantages: Power of the biceps belt pissing rod

Comment: The device is just a beast. Power is enough for everything. When the trigger presses you immediately feel how powerful it is. At the first acquaintance with Khopom, they said that everything is crumbling. Will start several times and then from the thirtieth. And so on. As a result, he examined everything well, did not listen to anyone and took a chainsaw from Hopra. After two.year use, definitely a hoper if the technique is suitable for needs. And buying a trimmer for grass generally pleased. There were many devices in their hands from different manufacturers. So I can recommend confidently. P. S. Just remember that you take a gasoline tool, not a kettle. Here is not only the button on.-Off., but also proper maintenance. The correct first launch, running.in, lubrication, cleaning, etc. D. All successful purchases!

Disadvantages: Assembly is bad. Half of the bolts are not swept. Fuel tank separate topic. For a year of use, changed three times. First time under warranty, then I bought separately. All three times the tank burst in the same place. The quality of the plastic tank is disgusting. The tank is suspended by only two bolts and brackets. protection of the tank is a plastic corner. After the first replacement, the tank bought enhanced metal protection, but she also did not help. The fuel tank bursts from the vibration of the braid for grass at the mounting site to the engine body.

Comment: This braid for grass was repaired more than worked. I don’t advise buying this braid.

Advantages:.comfortable (biceps belt).Powerful (grass to waist. In dust)

Flaws:. The resource of motorcycles is only 150 (like Huskvarny 600-). If something opens, I will complement.

-They scared that high grass to the waist would not be reimbursed by a trimmer, because everyone has everything wound up on a gearbox. Nonsense, any grass, any burdocks in dust and dust waves. _.Scared that he eats a lot, all the same 3 liters.With. Nonsense, tank here 2l. And for 3 tsenzil, all that was needed (half of the football field), and the grass was really in Posyas. Husqvarna’s neighbor 2 l.With. Eats the same. Scared that cheap and fall apart, everything will bounce. No, everything is tightly screwed and in general, I constantly beat her for bricks and wound the sticks and benches on it)). Nothing fell off. A crack appeared on the coil after I wrapped some kind of metal cable in the grass as a gearbox. But the crack is not significant, then it never went. Friends have been mowing such a mower for a year. Everything is good for them.

https: // jusof.COM/Katushka-dlja-Trimmera-PA6-30gf-Kak-Razobrat/https: // Poryadok.ru/catalog/katushki_leski_dlya_trimmera/https: // otziv-otziv.ru/Katalog/Trimmery/Hopeer/Trimmer-Benzinovy-Hoper-Fermer-052.HTML

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Winding fishing line on a trimmer for grass

Measured and accurate dismantling of a spray from the coil of braids for grass makes it possible to go directly to the winding of the fishing line. Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation. Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off the excess.

Trimmer head for grass with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode. It is almost impossible to incorporate a fishing line for a trimmer to a trimmer for grass with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic head of the trimmer for grass include the simplicity of the line for refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Types of woods for a trimmer for grass

First of all, in order not to resort to frequent replacements, it is better to use a denser fishing line for a trimmer. The number of its species and manufacturers is simply amazing. The main parameter of the fishing line for a trimmer for grass is its diameter. He varies from 1.6 to 3.2 mm. The most common view is a 2-mm fishing line for a trimmer. However, its selection must be carried out depending on your type of trimmer for grass.

cord, dressing, trimmer, head, disassembly, lawn

Distinguish several variants of the cross.line section. So, it can be round, square, in the form of an asterisk with sharp faces. The last option is the most effective. However, it is worthwhile only on powerful braids and at the same time you need to know how to fill the fishing line for a trimmer into a coil of a trimmer for grass. Therefore, we can conclude that the more powerful your lawn mower is, the more the fishing line for the trimmer should be thicker.

A process such as winding a fishing line on a trimmer for grass is not difficult, but has its own characteristics. First you need to choose the right fishing line for a trimmer, the diameter of which is registered in the device passport.

cord, dressing, trimmer, head, disassembly, lawn

First, unscrew the coil lid. Be careful, since the thread can be both left and right. The left thread is necessary so that during operation the head of the braid for the grass does not spin.

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Want to see? The rating of the best benzosos!

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken.

In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.

In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

  • The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.
  • The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. it is enough to correctly season the fishing line for a trimmer from the user.

The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside.

It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Learning to correctly wrap the fishing line for a trimmer to the coil of a trimmer for grass and lawn mowing instructions for installation

Owners of private houses know how necessary the type of tool is such as a trimmer for grass. It can be gasoline and electric, and they differ in the design of power units.

For injection of grass in areas where there are stones, trees and other obstructing objects, a fishing line for a trimmer is used as a cutting device.

This consumable in the process of use wears out, so how to wind the coil of a trimmer for grass, we will consider in detail in the material.

What you need to know about the fishing line on the trimmer for the grass

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device.

Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency.

This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material.

If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool.

With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.by.step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum.

The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same.

First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

  • Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
  • Next, from the rampart of the drum, the coil for the fishing line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
  • The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
  • To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
  • After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted
  • When installing the installation, the head should be planted in a tetrahedral slot
cord, dressing, trimmer, head, disassembly, lawn

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
  • If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
  • When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
  • If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
  • There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic).

The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head.

The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

  • Inside the head is a coil, which is planted on slots that prevent its free movement
  • The coil is affected by a spring that presses it to the slots located in the design of the cover
  • A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
  • During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
  • Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

The final moment of the instruction

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

How to wind a fishing line for a trimmer?

The winding method depends on the type of coil, however, in any case, you first need to choose the right cutting material correctly. On the packaging or in the instructions for each model, the diameter and shape of the fishing line is indicated, it is very important to use just such material, otherwise there will be problems with winding.

The spider is collapsible

Here is the procedure that needs to be performed in order to change the fishing line for the trimmer:

  • fix the gearbox of the trimmer for the grass to exclude the rotation of the head;
  • Weaken the bolt that holds the fishing line for the trimmer, rotating it with the help of the mesture key counterclockwise;
  • pull the remains of the string;
  • Cut 2 pieces of a new fishing line of the required diameter, the length of each segment is 20–40 cm;
  • Insert both segments into the holes of the coil so that they are separated in half;
  • Twist the fixing bolt.

Spider Negrivable and Wind

Here’s how it is necessary to act in order to correctly wind the fishing line for the trimmer to the coil of the lawn mower:

  • With your fingers, grab a fishing line for a trimmer passing along the inside of the coil and pull it out of the head;
  • Cut a new string into pieces of the desired length;
  • Insert the segment into the hole a little more than half the length, then wrap and remove it through the next hole;
  • If the fishing line for the trimmer is thick, then you can make pieces of smaller length and, after inserting into the coil, wrap the edge of the string so that it enters the next hole by 0.5–1 cm.

Semi.automatic (collapsible)

Here is the procedure that needs to be performed in order to change the fishing line for the trimmer:

  • Squeeze the latches to separate the upper part from the base;
  • Remove the upper part and pull out the spool without losing the spring;
  • Remove the remains of the old fishing line;
  • Cut a piece of string 2-3 m long;
  • Fold the segment by half;
  • Insert the curved middle of the segment into the sloping of the spool;
  • wind the string in accordance with the direction indicators on the rogue or upper cover;
  • fix the fishing line for the trimmer on both sides in the slopes of the spray;
  • Insert the rogue and the spring, passing both ends of the string through the corresponding holes;
  • Install in place and fix the top cover;
  • Pull alternately for each of the edges of the fishing line to remove the string from the latch.

Automatic (indiscriminate)

Here is the procedure that must be performed:

  • Press the shock button and pull the remaining fishing line from the head;
  • Transfer the button to the position of replacing the string, for which combine the tags on it and the upper cover;
  • Cut a piece of string 2-3 m long, insert this segment into the reel;
  • wind the string, rotating the button, the direction of rotation is indicated on the body.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

  • Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
  • You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
  • Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
  • Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
  • After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
  • By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
  • Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
  • By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

The step.by.step winding of the fishing line on the coil to wind the cord per trimmer for the grass can be also in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

  • Bend one end of the cord thread in the form of a hook.
  • At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
  • Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
  • The same actions need to be done for the second cell of the bobbin.
  • Assembly of the device head is similar to the first way.

Tips and recommendations how to wind a fishing line for a trimmer and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

  • Set the lid to clicks. over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
  • Do not wrap a fishing line for a trimmer with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
  • If you own the tool not with two conclusions of the fishing line, but with one (usually low.power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
  • After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting!Choose the material of the appropriate quality so as not to get injuries when working with benzo.cards, trimmers and motorcycles. In the process of beating grass, small stones and other materials fall under the rotating parts, which can fly over long distances, therefore, despite the fact that the fishing line for a trimmer is not a knife, working with a tool should be carried out in protective special uniforms. The result of the work done is as follows. after the replacement of the new material is enough for an area of ​​up to 600 square meters, but when taking into account the presence of a reinforcing layer on the fishing line. Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.button grass with fishing line, as there are special metal wheels or knives for this.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

  • Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
  • You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
  • Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
  • Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
  • After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
  • By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
  • Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
  • By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

The step.by.step winding of the fishing line on the coil to wind the cord per trimmer for the grass can be also in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

  • Bend one end of the cord thread in the form of a hook.
  • At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent over the end of the thread there.
  • Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the coil of the trimmer for the grass.
  • The same actions need to be done for the second cell of the bobbin.
  • Assembly of the device head is similar to the first way.

How to replace or put a starter spring in place?

If everything turned out to be in order with the rope at the starter, the suspicion falls on the coil itself. It is driven by a strip spring rolled into a roll. To change the spring, certain steps should be taken.

  • Remove the starter from the lawn mower.
  • Remove the starter coil.
  • Unscrew the main bolt holding the pulley on the case.
  • Pull out the exciting antennae and the spring, the strip spring is almost completely straightened or folded by rings of a larger diameter.
  • Hold it in advance.
  • Check if the spring is valid (there may be rusty stains, breaks, etc. D.). If the hooks at its ends are torn off, new ones will not be able to bend. high.carbon steel breaks when trying to bend it. Weakened hooks are suitable for easy bending.
  • Make sure that an auxiliary (ordinary) spring with washers in place. These details protect the coil frame from taging the end of the main spring. If the washers and the spring are broken, but there are no new ones, do not screw the coil bolt hard, but watch it. He can unscrew and get lost.
  • If the main (flat) spring of damage, insert the same new. Put a hook at the end of the spring in its place and bend it, inserts a round behind a turn into the space where it should be and should be.

The rewinding of the spring is performed in a minute. Oknovka in this action is gained quickly.

How to replace or put a starter spring in place, see the following.

Fishing lines winding algorithm

The procedure for winding the fishing line depends on the type of coil. with one or two antennae, as well as with automatic charging the cord.

On a reel coil

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

Husqvarna Trimmer 125C Starter Assembly Repair Broken Pawls

Advice! To understand which way to wrap the thread, you should look at the corps of the spool. usually marks are made on it indicating the direction of movement of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

To a coil with two antennae

In the rogues of this type, you need to inspect the inside of the coil and determine the number of grooves for winding the cord provided for in it.

Important! If there is only one gutter in the coil, then both antennae must be wrapped in a common groove, if two, then on separate paths.

For winding, you need to take a piece of fishing line with a length of two to three meters. For a spool with one groove, tie a fishing line for a trimmer into a through hole, combine a mustache, leve and wind it up in the direction in the direction of its rotation during operation. If fixing grooves are provided, they need to go through the ends of the cord, then stretch them into the output, and then close the coil and put them in the same place.

For a two.lep mewood, the difference is that the section of the string should be folded in half. Next, it is necessary to charge the middle of the bend into the groove between the grooves, and then wrap each of the pieces of fishing line on its path, fix the antennae and assemble the coil as well as the spool with one track.

On a trimmer head with automatic dressing

For heads with automatic refueling, it is enough to just start and squeeze the edges of the fishing line, and the tool will perform further winding on its own when turning on. It is impossible to make a mistake here, because the coil itself recognizes how the antennae should be located.

On a note! The advantages of trimmers with such a head include the convenience of laying the cord, and the disadvantages. high cost and complex repair.

Fishing line for a trimmer. varieties and the ability to replace other material

A cord for a trimmer for grass can be of different diameters (from 1.2 to 4 mm), and it must be chosen depending on which vegetation is required to mow. the thicker the fishing line is for a trimmer, the more rough grass it will cope. Experienced users recommend putting a fishing line for a trimmer 2 mm thick, which is a universal.

The shape of the fishing line can be round (for juicy grass) or with sharp faces in the form of a square or asterisk (for beveling dry grass). The second type is less durable and wear out faster compared to the round cord.

One of the popular issues regarding the work of trimmers is whether it is possible to replace a special cord for mowers with other materials, for example, metal or steel cables and strings, wire, etc.D. You need to know that the installation of such items is not recommended, because along with them the trimmer for grass turns into dangerous equipment. During the mowing, pieces of wire or metal will constantly break off and fly off in different directions, risking to injure the employee. And if you accidentally touch their limbs during work, a serious wound is provided.

Owners of trimmers interested in whether it is possible to use a fishing fishing line for a trimmer, we answer. this is allowed, but it will be much faster to tear and wear out, which means it is a frequent replacement.

Advice! The fishing fishing line for a trimmer is good for cleaning herbs near a fence or metal mesh-instead of spending an expensive trimmer cord, you can charge a large caliber tackle (2-3 mm), which is much cheaper.

Characteristic malfunctions and their independent elimination

Naturally, during operation, the owners of the trimmers are faced with certain malfunctions of mowing heads. over, they are most often associated with certain difficulties in pulling (lengthening) of the cutting cord from the coil. The most common causes of the lack of fishing line is its “bite” between the turns or sticking.

If the string is not served

In this case, the cause of the defect is incorrect winding of the cutting cord. A trimmer fishing line can be wound with insufficient tension, which helps to cross the turns together and confuse the string. When the coil rotates, the cutting cord under the influence of the emerging centrifugal force is delayed, which in turn leads to the clamping of the free end of the fishing line between the turns. To eliminate this malfunction, you need to dismantle the coil, disassemble it and rewind the string so that the turns lie down in even rows, pressing tightly against each other.

If the string sticks together

Squeezing of the turns of the fishing line directly in the mowing head can be caused:

Advice! To avoid sticking the cord inside the mowing head, experts recommend applying a thin layer of silicone lubricant after refueling the string to the coil. In addition, it is better not to use a fishing line for a trimmer of unknown manufacturers.

If, nevertheless, the user could not avoid sticking the fishing line, then to repair the trimmer coil for the grass, you need to remove and replace the existing cord with a better.

If there is too much string consumption

When using semi-automatic mowing heads, the user can detect the accelerated consumption of the cutting cord due to its spontaneous lengthening. As a rule, this happens due to the weakening of the spring installed inside the coil. You can eliminate the malfunction by putting several goals under the spring.

If the bobbin does not spin

The refusal to work the semi.automatic coil of the trimmer for the grass can also be caused by a frequent clash of its head with solid objects (dry branches, soil, stones, etc.). In this situation, there is a slight stretching of the fishing line, and then the rapid retraction of it inside the bobbin. Due to severe friction, the cord is heated, which can lead to sticking its turns to each other. To eliminate the defect, the string will need to be rewound.

If the string is served spontaneously

Spontaneous lengthening of the fishing line, followed by pruning its tips, may be caused by a violation of the order of assembly of the head after replacing the cutting cord. Often, users who do not have sufficient experience forget to install the pressing spring inside the head, which causes premature operation of the mechanism responsible for the supply of fishing line.

Dismantling the spit head

Starting to repair the head of the trimmer head for grass, the owner needs to protect yourself from injuries when randomly starting the engine, for which you must completely de.energize the electric garden tool or drown out the engine motorcycle engine. Most often, the owner of a trimmer for grass is faced with the need to replace the cutting cord. This process is started after the head is dismantled from the shaft. This must be done carefully to avoid damage it.

Important! The gearbox shaft, which is equipped with a trimmer for grass, has a left thread at the end, so the mowing head is taped clockwise when removing.

Dismantle the coil in the following order:

  • Having combined the holes available on the axis and washer, the mowing shaft is rigidly fixed by means of a screwdriver or a metal rod;
  • unscrew the executive mechanism, rotating its case clockwise.

Having removed the braid head, they begin to disassemble it, for which you need to carefully open the lid, which is most often attached specially provided for by plastic locks. To do this, squeeze the edges of the lid and at the same time drown in the hull of the latch.

Attention! If the trimmer for the grass is equipped with a semi.automatic head with a button at the bottom, then it needs to be opened by observing special caution, when removing the cover, a pressing spring can fly out and get lost.

Charging the string in the spool

To charge the fishing line for the trimmer correctly, it is necessary to act according to the instructions for the operation attached to the trimmer. As a rule, this operation is carried out as follows:

  • cut off the right amount of cord and fold it in half;
  • The resulting loop is inserted into one of the specially provided grooves (holes) of the spool;
  • Pulling the fishing line for the trimmer, they turn the spool counterclockwise several times, while the coats of the cord should be laid in dense layers (one to the other), avoiding overlap;
  • Having finished winding, the ends of the fishing line (about 20 cm) are left free, which are fixed in the grooves available on the sides of the spool;
  • mount the mechanism in their place, for which it is necessary to assemble it in the reverse order, returning to its original position all the available details (spring, washers, etc.), and install the coil with a string in the body of the head;
  • The free ends of the cord are passed through the existing eyes (holes), after which the body is closed with a lid, which is fixed with latches.

On this charge of the spitter head, the cord can be considered complete. The coil is screwed onto the shaft of a trimmer for the grass, having previously stiffly fix it. How to do this described above. You can check the performance of the head by mowing a small area of ​​the lawn.

Advice! In those cases when the owner of a trimmer for grass prefers to replace the failed head of the new one, experts recommend avoiding the acquisition of cheap non.original coils brought from China.

Self.manufacture of bobbin

Quite often, a trimmer for grass is operated in the distance from places where you can purchase spare parts for a spitt with its breakdown. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

  • A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
  • A hole is drilled in the center of the disk, which matches the diameter with a shaft of a trimmer for grass.
  • Small eyes are attached to the opposite sides of the disk, which will serve to refuel the fishing line.
  • Through the eyes, pass the fishing line for the trimmer and fix it with ordinary screws or screws. The coil is ready for work.
  • Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer for the grass with a nut.

Important! It must be remembered that to tighten or unscrew the nut without hard fixation of the shaft.

To replace the fishing line on a home.made bobin, you will have to release fixing screws, insert a new section of the string and tighten the fasteners again. It is not necessary to remove the coil from the shaft of the trimmer for grass, however, it is necessary to exclude the possibility of spontaneous launch of the motor.

So, above was step.by.step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.