Electrician on a single tractor with your own hands. Furious generators. How to make yours…

Installing the generator on a single tractor with your own hands

It is quite difficult for a novice farmer to choose the right generator for a walk.behind tractor. However, not everything is as difficult as it might seem at first glance. The only and most important factor to pay attention to is the power of the device. Whatever the generator for the agricultural machine you choose, its power must exceed the total power of the loads under which the one.axle tractor works. This will allow the device to work regularly at a voltage of 220 volts without the risk of jumps in the electric network, and feed all the electrical appliances available on the walk.behind tractor.

Often, the owners of the walk.behind tracts do not have experience and equip their equipment with generators intended for installation on cars. This is the best option in cases where the farm regularly uses a powerful single.class single.class single tractor. In other cases, buying such generators is impractical due to their high cost.

How to put a generator on a single tractor. an algorithm in details

Before installing a generator on an agricultural unit, you should study in detail the device of the existing element. The generator to the walk.behind tractor consists of these details:

• The case. in most cases, is presented in the form of a metal box equipped with the front and rear lid;
• Shkiv. this part is designed to transmit mechanical energy from the motor to the shaft of the generator through the belt;
• Stator. the role of this part is played by the usual rewinding of steel sheets collected in one compact package. In its form, the stator resembles a pipe inside which generator power is produced;
• rotor. this part has the shape of a steel shaft equipped with two metal bushings. On the site between the bushings there is a winding of excitation, the wires of which are connected to the contact rings;
• The brush knot is a plastic part responsible for the working generator;
• The voltage regulator. this part is responsible for stabilizing the voltage when the load level changes to the generator.

The installation of the generator n one.time tractor with your own hands takes a large amount of time, but by spending it, you will ensure the uninterrupted operation of your agricultural machine. It is necessary to connect the generator to the unit in compliance with the electrical circuit, which collects and describes all necessary for the installation of the connection.

From ignition

In order to connect lighting to your own generator, you will need:

• soldering device;
• screwdrivers of different sizes;
• electric drill;
• spanners;
• Kusachiki;
• electric cable;
• headlights along with dimensional and rotary lights.

Step.by.step instructions for lighting from ignition:

• It is necessary to choose the right headlight. It can be a new model or used from a motorcycle, car, tractor.
• Buy a tooth switch and all the necessary wires.
• Install the headlight. The most acceptable place on the design of the walk.behind tractor is considered the crossbar of the steering rod. With this arrangement of the headlight will illuminate all the necessary space and be polluted at a minimum. Optimal elevation 100-120 cm above the ground.
• In an accessible place you need to fix the toggle switch.
• The wiring broach depends on the design of the walk.behind tractor. If it provides for the connection of the headlight, then it is necessary to be paid in this place. If this is not provided in the design, then it is better to do this from 12 watts of the oil indicator lamp. The mass of the motor block acts as a mass.
• We spend the cable to the toggle switch and to the headlight itself. Fix them with a clamp, in its absence. isolet.

To protect all the wiring from moisture and dirt, the cable is recommended to be carried out in a corrugated pipe. It must be pulled to the steering column so that there are no sagging.

When working from your own ignition, it is important to remember that the light will dull at low speeds or at idle.

Without a generator

You can do without an electric generator well. To do this, you need a 12 watts with a LED lamp or a gel type of battery. LED lamps will allow the battery to work longer in bright light.

• Decide where to install the battery. Typically, this part of the structure, which is located between the engine and the speed box.
• Cook from corners fixing stands.
• Fix the cooked design to the frame of the walk.behind tract through four bolts.
• Place the battery on the stand and fix it with a metal plate, 2 long bolts with nuts.
• Introduce the flashlight. This must be done so as to illuminate the maximum space and at the same time not to blind the operator or oncoming vehicles.
• Combine the wire to the headlight and switch. In the area of ​​connection, seize contacts and insulate.

The result is a bright, extensive beam that will work all the time, as far as the battery is enough. The negative aspects of this option include the requirement to regularly charge the battery.

The above methods for connecting lighting can be used both on domestic motor vehicles and imported. Each option has its disadvantages: if you connect lighting from the ignition, it does not work well at idle, if you connect with the battery, then it must be regularly charged. The flashlight itself should be placed so that it makes lighting as comfortable as possible for the operator and oncoming vehicles.

Light without a battery and generator

Deciding how to make a headlight for their walk.behind tract, most make the most difficult solutions in the technical execution of. You can make light simply, quickly and inexpensively if you use the bicycle lamps.

Bicycle lights have the following advantages:

• There is no need to lay wires;
• a minimum of financial investments with high efficiency;
• reliability under any weather conditions;
• the presence of your own charger for portable batteries;
• the possibility of fastening on the steering column on the brackets that are included;
• speed of removal for use in manual mode or for charging.

Buy two bicycle lights. One is advisable to use for high light, the second. for lighting immediately in front of the unit.

How to make a headlight on a single tractor?

As a lighting on the one.based tractor, many special equipment owners install headlights of domestic and foreign machines. This option is of high cost and unreliable. Outgoing light is not enough, and the system itself will not last more than a few months. As an alternative, they develop a headlight for a single.based tractor with their own hands, which allows you to get the right lighting and equipment power.

Step.by.step instructions for manufacturing:

• Buy an old inexpensive headlight. Equipment from Soviet cars is suitable.
• Remove glass protection and other elements fixed with plastic fasteners from the device.
• Pour the headlights with a gypsum, for which the finished material is spilled into the device and remains until it dries completely. After that, you can remove the cast, preserving its integrity.
• Fiberglass is applied to the resulting template, and each time processing the material with epoxy resin. After processing, the future headlight should dry in a vacuum.

The headlights of domestic machines are installed by many owners as lighting on a single tractor

Before using the headlights in the walk.behind tractor, it is necessary to check the performance of the device and the lack of short circuits several times to avoid breakdowns.

Electric circuit

The connection diagram of the headlight is quite simple and consists of only three main elements:

• power source, including ignition, generator or battery;
• Power switch. a simple button that breaks and turns on the electric power circuit for the lamp;
• A cartridge for a lamp to which the wires are attached from the power source through the switch.

A fairly simple diagram of connecting the headlights on a single tractor for greater reliability all wires are placed in a special corrugation. The material protects the wiring from damage and allows you to fix the equipment so that it does not interfere with the use of the one.based tractor.

Necessary tools for work

Before starting work, it is necessary to prepare all materials, including wiring, headlight, corrugation, as well as collect a set of tools:

• soldering iron;
• screwdrivers and wrench;
• Kusachki and stationery knife;
• isolet and thermal tube;
• electric drill and fasteners.

How to make light on a walk.behind tractor without a generator?

You can provide lighting on a walk.behind tractor without using an electric generator. It is enough to get a 12-volt battery with an LED lamp, or a gel battery (for example, from an electric scooter).

The priority task is to find a suitable place for the future attachment of the battery. The area of ​​the frame between the engine and the speed of speed switching is best suited for this.

Subsequent actions to install the headlights are as follows:

• preparation of a reliable stand-up for the battery (can be welded from corners);
• fastening of the stand for the battery to the frame of the walk.behind tractor 4 bolts;
• Place the battery on the stand and fix it with a metal plate, 2 long bolts and 2 nuts;
• stretch the wires to the headlight and switch. After that, solder the contacts in the joints, insulate them with a tape.

We also offer you to familiarize yourself with the video, which tells about the installation of headlights on a single.based tractor with power from a removable battery:

This type of lighting gives a fairly bright, powerful and uniform ray. The charge is enough for a few hours of use of the battery. The only minus of such lighting is that the battery will regularly need to be recharged.

Motoblocks of manufacturers Neva, MTZ, centaur and other companies do not have headlights in standard configuration. But with the help of our advice, your uno.ears tractor will be a reliable assistant for you both day and night!

Electro generator connection

The optimal way to connect light on a walk.behind tractor is to use a generator that is included in the machine’s configuration. As a rule, standard electric generators for all models of this special equipment have excessive power, which can be used to operate the lighting device. Connecting the headlight to the energy source takes place according to the following algorithm:

• Using the wiring, the lighting element is connected to the generator;
• One of the wires is equipped with a toggle switch, which is desirable to place at the steering wheel or in another place convenient for the driver;
• After checking performance, the electrical wiring is placed in a protective corrugation and fixed on the mini-machine case.

If the standard generator has sufficient power, then the lighting will be bright and stable. When, when the load on the device is increased, the lantern begins to flash and turn off, it makes sense to think about replacing a standard electro generator with a device from any tractor model.

Carefully! When using equipment intended for other equipment, it is necessary to provide the uniform tractor with additional supporting frames that increase the strength of the fastening.

How to make light on a walk.behind tractor without a generator?

It is quite possible to connect light on a walk.behind tractor without a generator. You will need an LED lamp and a 12-volt battery. You can use a battery (battery) from a car, a gel battery that is installed on electric scooters/electricity.

It is important to correctly choose a place to install a battery. Often it is compact, so you can use the site on the frame between the engine and the checkpoint.

The battery installation is performed according to the following scheme:

• Steel mounts are prepared. In size, they should fit under the battery;
• Ready fasteners are screwed to the frame with four bolts for their reliable fixation;
• The battery itself is installed, for the consolidation of which two bolts, nuts and a metal plate are needed;
• The electrical wir is extended from the battery to the switch, then to the electrical equipment (headlights on the walk.behind tractor). All sections of the accession of the wires are fixed with rations and high.quality isolate.

As a rule, the headlight attached to the battery shines evenly and intensively. The battery is enough for a couple of hours of continuous work, but periodically it will be necessary to recharge from the source of electricity. Therefore, it is worth trying to make light on a walk.behind tractor from ignition. The wire is connected directly to the ignition system, the toothbler and the headlight. So the lighting is turned on only during the operation of the unit.

Choosing a generator

one.axle tractor or motor.cultivator can be equipped with an electric generator. Such a device makes it possible to nourish an electric lighting lamp or headlight to work freely at night, or to charge the battery. The battery in the unit is installed so that you can quickly start the device using the starter and then feed electric parts.

Car generator on the engine of the walk.behind tractor

When buying a generator to the motor unit, you should pay attention to power. When working, the power of the device should be greater than the installed load. And this means that if all electrical equipment at the unit works, there should not be voltage drops in the generator

The power of the generator will not necessarily be 220 volts, the main thing is that the power is greater than the required load. You can put a tractor or automobile generator on a one.axle tractor (motor.cultivator)

And this means that if all electrical equipment at the unit works, there should not be voltage drops in the generator. The power of the generator will not necessarily be 220 volts, the main thing is that the power is greater than the required load. You can put a tractor or automobile generator on a one.axle tractor (motor.cultivator).

one.1 installation of the generator on a single tractor with your own hands

For independent installation of the device, you need to get acquainted with the main parts of the design:

• A pulley that transfers mechanical energy, which comes from the engine, to the shaft of the device using a belt.
• Metal case consisting of the front and rear covers.
• Rotor. a steel shaft with two steel bushes between which the winding of excitation is located. The wiring of the winding is connected to the contact rings.
• Stator. rewinding consisting of a set of steel sheets assembled together. This part is made in the form of a pipe, and it is in it that the device is powerful. The part can be done with your own hands.
• The voltage regulator maintains voltage at the same level, in conditions of load changes.
• The brush node is a plastic mechanism that helps the device work correctly.

Installing a generator on a single tractor does not require much time, but this is a very important detail for the normal operation of the device. The structure is connected to the walk.behind tractor using email. schemes in which all the necessary connections are shown.

one.2 electrical circuit

If the electrical circuit is incorrectly connected, the generator winding can fail. Such a device can be connected with two wiring. The electronic unit has four wires, two of which are blue, they connect the energy converter. The remaining two wires are red and black. Red wire is a voltage output, it nourishes headlights, signal and other electrical appliances. They also use it to charge the battery. Black wire is brought to the mass of the power device. Connection of the device can be made with your own hands.

Connection diagram to check the generator

The generator produces email. energy that enters the rectifier in an electric unit. The unit has a voltage equalizer and a current regulator. These devices are needed so that the voltage does not change, regardless of the performance of the device.

The current control controls its number, which enters the battery. The engine turns on and transfers the torque to the rotor by means of the belt. The part begins to produce voltage into an electric unit. The launch of the motor reduced the battery capacity, so all electric parts will receive power from an electric unit.

How to make a headlight on a single tractor?

As a lighting on the one.based tractor, many special equipment owners install headlights of domestic and foreign machines. This option is of high cost and unreliable. Outgoing light is not enough, and the system itself will not last more than a few months. As an alternative, they develop a headlight for a single.based tractor with their own hands, which allows you to get the right lighting and equipment power.

• Buy an old inexpensive headlight. Equipment from Soviet cars is suitable.
• Remove glass protection and other elements fixed with plastic fasteners from the device.
• Pour the headlights with a gypsum, for which the finished material is spilled into the device and remains until it dries completely. After that, you can remove the cast, preserving its integrity.
• Fiberglass is applied to the resulting template, and each time processing the material with epoxy resin. After processing, the future headlight should dry in a vacuum. The headlights of domestic machines are installed by many owners as lighting on a single tractor
• Then proceed to the independent manufacture of glass. This will require an oven, special rails and fiberglass. From the slats, it is necessary to make a platform that is placed in a preheated oven to 180-200 ° C, where they put fiberglass without a protective film.
• Когда материал начнет деформироваться, его можно доставать для нанесения на обработанную заготовку. After pouring the form, it is necessary to place the future headlight in the vacuum.
• After complete cooing, the product is grinded using sandpaper.
• The final stage. installation of electrical equipment, installation of a lamp.

Electric circuit

The connection diagram of the headlight is quite simple and consists of only three main elements:

• power source, including ignition, generator or battery;
• Power switch. a simple button that breaks and turns on the electric power circuit for the lamp;
• A cartridge for a lamp to which the wires are attached from the power source through the switch.

A fairly simple diagram of connecting the headlights on a single tractor for greater reliability all wires are placed in a special corrugation. The material protects the wiring from damage and allows you to fix the equipment so that it does not interfere with the use of the one.based tractor.

Necessary tools for work

Before starting work, it is necessary to prepare all materials, including wiring, headlight, corrugation, as well as collect a set of tools:

• soldering iron;
• screwdrivers and wrench;
• Kusachki and stationery knife;
• isolet and thermal tube;
• electric drill and fasteners.

Without an electric generator

Another method of connecting lighting is also widespread among operators. Here it will be possible to do without the use of the generator. You will need a 12 volt battery and LED.

In addition to the sources, you must think in advance where this device will be attached. If you are the owner of large transport, then the installation of the battery between the gearbox and the engine will be the ideal solution.

• Using welding and iron corner, you need to make a stand for your gel battery. It is attached to the mini.vector frame.
• A battery is installed from the inside, which is clamped by a pair of bolts and a metal insert.
• Wires are laid from the battery to the power button. All joints in the joints need to be sealed and isolated by a heat.shrinkable ribbon.

Such lighting will turn out to be very bright. However, this method of installing the headlights has one negative side: the full charge of the battery will be enough for literally a couple of hours of work, after which it will need to be recharged again. This is a very significant minus for those who work intensively with a mini.tractor.

Please Turn JavaScript on and Reload the Page.

Many manufacturers produce this agricultural mechanism without built.in lighting. This is where the question arises, how to connect the headlight to the Unoic tractor on your own with your own hands. Before installing lighting on a single tractor, it is worth considering its class. These units of the middle and heavy class are equipped with a generator, which serves as source of charge for the battery and power supply. On these versions of the mechanism, it is possible to connect several front and rear headlights for trailer to the walk.behind tractor. as well as turning indicators.

Many manufacturers produce this agricultural mechanism without built.in lighting. This is where the question arises, how to connect the headlight to the Unoic tractor on your own with your own hands. Before installing lighting on a single tractor, it is worth considering its class. These units of the middle and heavy class are equipped with a generator, which serves as source of charge for the battery and power supply. On these versions of the mechanism, it is possible to connect several front and rear headlights for trailer to the walk.behind tractor. as well as turning indicators. The launch of the motor block provoke an electric starter and a battery, which is installed in a special pallet and firmly fixed on the mechanism frame.

The electrical circuit works very simple. The generator produces electricity that.

A flip of a revolutionary variety, homemade

The revolutionary plow for the walk.behind tractor is universality. The presence of a revolutionary manual mechanism makes it possible to turn the soil on one side with a lemch. The minus is believed that the whole process constantly has to start from the same angle of the field due to the coup on one side.

Roting agromechanism works in three main planes:

In the first version, when dismantling the dumpy and stump component, the agricultural device is placed on the surface of the table tightly pressed against the wall, the sides of the structure are moved vertically to the wall. In this case, the surface of the countertop and the horizontal plane of the band coincide. A good model of a revolutionary plow for a walk.behind tractor made, the bottom of the cutting edge when installing a piece should be lower than 2 cm.

Important: with the assembly process of a revolutionary plow for a walk.behind tractor, you must be careful and monitor the maximum coincidence of the details of the motor cultivator without the presence of gaps between them.

In the second option, the lateral cutting part of the bowl should be installed directly with the cutting side edge of the dump. These details of the correctly assembled agricultural structure should not be more than 10 mm distance.

The third version should be connected to the working surface of the bowel and dump without the presence of gaps with a single.plane position. Details for better work are polished and regulated, avoiding the protrusion of fasteners. In addition, cleaned parts are watered with butter or solidol, then rubbed with fabric. This protects the surface from the influence of negative media and corrosion. Therefore, a revolutionary plow for a walk.behind tractor is considered the most common model that differs in the simplicity of the assembly process and excellent operational capabilities.

Electrician on a single tractor with your own hands

I needed the light on the walk.behind tractor. For I use it almost daily and year.round. Last winter, I was almost knocked down by the oncoming cars that went around in our hole various obstacles, natural and not very. It was then that I thought about connecting light. I have a “virgin land” one.based tractor, 6.5 horses with a Lifanovsky engine. Having reviewed a bunch of rollers on the internet, I found that the light on the walk.behind tract is quite unwilling hemorrhoids. And what only people do not invent! Just a battery, and car and tractor generators and hell knows what else. By the way, tractor generators noticeably ahead of their car brothers, as they are self.exciting, produced direct current and do not require the presence of a battery. Do not believe the fakes on YouTube, where they show how an alternating current generator (automobile) suddenly for no reason, without a current of excitement, begins to produce a coveted current and lights a light bulb during rotation! Consultation with a number of local experts clarified the situation: firstly, the rotation speed of about 3,000 rpm is required, with the residual magnetization of the rotor. Then the generator can self.exclude and begin to work. In any case, there are a refinement with a soldering iron (I will not advertise, look in Google, look at YouTube yourself). In addition, this generator is still required to somehow add up to the walk-behind tractor, and this already requires welding and locksmith work. In principle, nothing is impossible, but this path is a little long and the thunder is essentially, and I wanted light here and now, immediately. The first thought was to install an ordinary dinema from a bicycle. For this case, a Ketai production set was purchased, with a very beautiful headlight and outwardly solid Dynamo for 12 volts. During the purchase, two exits on it were especially inspired, where it was written “12 V” and “25 V”. I, fucking, do not know how speed the Ketaytsy ride on bicycles, but the stray.fitted luminous of the bell tinned on the motornote, frankly, not very. In addition, disappointments and discoveries fell on me, like from a cornucopia. Firstly, the exit by 25 volts did not work stupidly. Consors himself with the thought that Dynamo is simply produced in two modifications, but in one building, I continued to work to increase the stress. For this, Dinama was removed from the native head and another, smaller size, to increase the speed of rotation and, accordingly. increased voltage. It became a little brighter than before. Having made a trial trip, for about three kilometers, the headlight was satisfied, especially oncoming, transverse pedestrians and motorists often showed me a thumb as a sign of approval. That evening I went to bed happy. But in the morning, happiness melted with sleep. The next day, Dynamo refused to work. Studies have shown that there is not a single bearing in it, and due to friction there stupidly put the windings of the coils. Having bitten himself for his elbows, he threw the Chinese shit into the toilet. Fate was cruel to me, and I began to prepare for the installation on the uniform tractor of the automotive scheme of lighting (generator, battery, etc. etc.). I watched the videos on YouTube dejectedly, sighed enviously and fucked up how I did not want to take up this dirty business. And then I, comrades, dawned on me. Why, there is electricity on the walk.behind tractor! There is, it cannot not eat! Some kind of garbage produces a current for a spark! She will have to share her electricity. I decided. And took out the tool. Having examined his shaitan machine, noticing where the wire dives from the candle, I began to disassemble the unoic tractor. The first thing I took off the rattle: then the rest of the casing: and my gaze appeared a hell of electricity: carefully examining, I found two wires emerging from the coil. One went to the candle and I did not touch it (as knowledgeable people told me on the phone, that there are about a few kilovols, so it is better not to poke the fornicial pens). The second went to control and power sensor of oil control. From there, I decided to scoop up a few volts for the headlight that remained for me from a ketai bicycle miracle. But the greedy candle did not want to share. As soon as I connected the headlight, the engine began to stupid, even the lamp did not have time to flare up. My hope was also stalling at the end of the tunnel of torment. The Internet again, again searching for a solution. I stumbled upon a moped bell. non.crap. Finally brutalizing, jumped into Mashyna and rushed to the local market, to the pavilion, where they sell spare parts for walk.behind boats and mopeds. The seller quickly cooled my impulse, explaining that only part of Mopedovsky Magneto on sale, the one with coils. Stator, being a piece of iron with splashings of magnets. A thing for centuries, practically does not fail, is not in demand, the seller explained, so it can only be under order. Well, and the price also bites brutally. And here I am ̶p̶i̶d̶a̶n̶h̶l̶o̶. I asked if there was an ignition coil on sale and received an affirmative answer. What a dick, I thought, since one coil is not enough, because you can wind a second coil, on the other side of the rotor with a magnet, which will give all its electricity to my light bulb, without a trace. A coil was purchased. The seller: he later asked to go in and tell what happened to me, for which I had a small discount of advance. In the neighboring pavilion, a metal.ash plate 2 mm thick, bolts, wires and other penny garbage were purchased in a neighboring pavilion. Arriving home, I began to mount the coil from the opposite side of the rotor with the magnet. Here’s what I did: but here the remnants of the Ketai know-kau surprised me again. The bulb in the ketai headlights barely smoldered. Once again, having once marveled at the speeds of the Ketai cyclists, I rushed into the car shop for LED lamps, reasoning that they consume less, and the meaning of the voltage, there is enough stress, that they would light them up. Indeed, enough. Fuck all the LEDs fucking. The experiment showed that the alternating current of the coil is categorically not suitable for LEDs. In despair, I twisted a bulb from a flashlight and no longer hoping, for the result, I put it in the Ketai Far. It got dark. The day is almost over. A single.axle tractor was shaking quietly, and the Ketai headlight with a 3.5.volt light bulb and 0.26 ampere illuminated my silly face with a smile to the ears. P.S. There were small nuances. It is necessary to cut off the part of the casing of the casing under the new bastard, the armored vehicle for the candle dangling between the legs of the walk-behind tractor, come up with a kind of cover from above so that it does not fall on the reel, if this happens during the trip. But it doesn’t scare me anymore.

How to make an electric motor block with your own hands?

A reliable electric uniform tractor for plowing the Earth can be done quite calmly with your own hand. This is not expensive pleasure and does not require special monetary investments. Electric engine blocks are easily collected, and all the necessary details can be purchased in free sale. Do.it.yourself design consists of several steps:

• At the first stage, the frame is made. To do this, you need a channel and a corner. It is important to consider that the size of the frame and the motor is the same. For the role of handles, it is best to weld two pipes along the edges of the frame, after which the handles are fixed with a metal insert that carries the function of the axis;
• For excellent fixation, the bracket should be attached in the middle of the pipe. A small platform for installing the electric motor is mounted on the frame;
• the wheel that transfers the movement of the belt is connected to a similar wheel on an electric engine. Next, the chain transfers movement below the installed star. The bicycle chain will cope with this task perfectly;
• Electric uniform tractor for plowing the Earth involves the presence of attachment equipment by machine. There are a lot of variations, curved metal knives can fit well, which can delve into the ground and easily loosen it;
• To facilitate the work, it is recommended to install a special coil, on which the extra wire will be wound. Management is best carried out using a switch. Do.it.yourself electric electric tractor is ready.

Features of an electric motor unit. Reviews of the owners

Manual electricity block has a number of its features. One can definitely say that this unit is designed for a certain soil. According to the owners, you can see that the car plows excellently loose and light land perfectly. In addition, the uniform tractor can be equipped with a rather large set of hinged guns that can greatly facilitate work on Earth.

An electric one.based tractor for a summer residence will not only plow the ground, but also help in its fertilizer. Will be able to perfectly enrich the soil with oxygen, improve its structure, which will “thank” with a plentiful harvest.