How can you cut plastic panels

How to cut plastic pvc panels at home

These tools dramatically speed up the length change process and also provide a superior cut edge appearance. All these recommendations help to properly saw and cut the chipboard, but chips, nevertheless, cannot be completely avoided. How to connect mdf panels? A circular or electric circular saw is a powerful construction tool, the main task of which is to work with wood and materials similar in spirit..

All sheets that are made of polymers (plastisol, polydifluorionad, polyester, pural) can be cut with a jigsaw, angle grinder or a construction knife. You need to drive the saw with slight pressure, at an acute angle to the surface, constantly monitoring its position; for cutting chipboard and chipboard slabs with a jigsaw, the saw line should be scratched or even cut through. If you already know how you will cut pvc panels at home, you should also prepare a tool. This will significantly reduce the number of rejected and damaged panels, and save a novice craftsman from wasting time, money, and, above all, from injuries..

How to cut plastic panels at home

PVC panels. modern finishing material, which has successfully and deservedly gained popularity in the field of interior decoration.

It is necessary to cut correctly with the wrong side of the panel down, because during processing under the influence of the load, the profile of the strip changes and causes some inconvenience during the installation process. When processing plastic with a circle, the angle grinder turns on only at low speeds, which will avoid damage to the material due to melting of the edges. If you are cutting several panels that need to be the same length, you need to place them on at least two supports. And further from the tool, if we work with a hacksaw on a tree with a fine tooth, the main thing is to cut it without a jerk, the MDF is laid on a horizontal surface with reliable fixation (with a foot, for example). Among the variety of finishing materials used in construction, plastic panels occupy a separate category. To give the desired color in one tone, additional dry mixtures, and for drawing a picture – thermal printing, using an auxiliary roller heated to a high temperature.

To cut pvc panels, you can use different tools, each of which has its own advantages and disadvantages. Thinking about “how to cut plastic”, you can remember about a hacksaw, be it for wood or metal. On the one hand, the workpiece is cut at an angle of 45 degrees and sharpened, on the other hand, a handle is made of electrical tape for easy holding and safe use. A stationery knife is considered a more suitable tool for this, because using it, the material is not completely cut. Using a jigsaw is very convenient to cut stacks of panels, but you should make sure that their height does not exceed the length of the file installed in the tool.

Recommended

In the children’s room for a boy of any shape, blue, blue, green and white tones traditionally prevail..

Classic brown linoleum and moss colors look quite presentable and can be used both in residential and public areas.

Most of the panels are made in accordance with the technology and unforeseen mechanical damage to the outer layers can aggravate their protective properties. It can easily cut plastic wall panels, if it is not possible to purchase a special cutter. And yet, I didn’t have to work, but I heard that there are special nozzles with a reverse direction of the teeth, they seem to have been developed specifically for chipboard and MDF. You need to start by preparing the place for cutting, it should be comfortable, ventilated (with the work of some tools, there is a lot of debris and dust). For cutting pvc, use a tool with small teeth for wood (cross-cut) or metal. When the edge of the panels is hidden from the eye by the starting or corner finishing profile, then a hacksaw is used for wood. The jigsaw will perfectly cope with the task of cutting panels folded in a stack, the main thing is that the stack height does not exceed the length of the file.

Bathhouse decoration inside 70 photos of cozy solutions for relaxation

The design of the rest room in the bath is developed according to an individual project or copied from ready-made stylistic solutions.

What wallpaper to glue in a small kitchen photo ideas 2021 2021

On

Bathroom design with shower 30 modern options

Bathtub with shower cubicle two in one. For this option it is enough Now there will be a bunch of photos of the interiors of bathrooms combined with a toilet and a shower instead of a bath.

Plastic panels: how to cut and how

Today, a variety of materials are used for wall decoration. Their choice is so great that it is difficult to decide. Moreover, each material has certain properties. They are worth considering. In some cases, only plastic panels are relevant. How to cut such material, not everyone knows.

Installation features

So what’s the best way to cut plastic panels? It all depends on the condition of the surface being trimmed. This is the whole complexity of installation. If the surface is flat, straight and smooth, then you can immediately cut the finishing material by adjusting all the details, as well as cutting the required number of panels.

If the surface has irregularities, and also requires curly cuts, then the process of installing the finishing material will be somewhat complicated. In some cases, a wall can include architectural features such as ledges, doors, windows, and so on. In this case, the plastic panels will have to be cut during installation..

Use of power tools

So how to cut plastic panels? For such purposes, many use a jigsaw. However, during the cutting process, it is necessary to strictly monitor the pressure. Otherwise, the material may not withstand the pressure and break. To speed up the installation of such panels, many use circular saws and an angle grinder, but experts do not recommend using such a tool. Plastic itself is fragile and can easily break if handled carelessly. In addition, the material may become hot during the cutting process due to the high speed of the blade. As a result, the edges of the panels may melt. In addition, when heated, such material begins to emit toxic substances..

What are plastic panels

Plastic panels are an irreplaceable material for surface finishing in bathrooms, garden houses, loggias, toilets. After all, it has several advantages. So what is the difference between plastic panels? How to cut such material and how? Among the advantages of the panels, it is worth noting their resistance to moisture. In addition, they are classified as low-flammable materials. It’s easy to mount them. In addition, plastic panels are resistant to abrasion, so they last a long time and are relatively cheap..

Plastic panels: what to cut?

It is worth noting that such a building material is quite simple to process. You can cut the plastic panel with almost any tool. Usually, a hacksaw for wood or metal is used for such work. In this case, the size of the teeth on the tool should be taken into account. The smaller they are, the better. The main advantage of this method is that, if necessary, you can cut several panels at the same time. In this case, the facing material is recommended to be placed with the front side up, at an angle. The panel is cut very easily. However, strong pressure should be avoided..

If you decide to use a wood saw to cut plastic panels, then you should choose a tool for mixed or cross-cutting, with undivided teeth. The result will be a neat and even edge..

Can I cut with a knife

You can also use a utility knife to cut plastic panels. To do this, an incision is made on the surface of the material using a ruler. After that, the panel simply breaks. It is not recommended to use a regular knife. This cutting method is much better than those described above. However, cutting panels with a cellular structure with a knife is almost impossible..

Hacksaw

If, when performing finishing work, the question concerns how to cut the panels exactly, then for such a case, it will be correct to use a hacksaw. When the edge of the panels is hidden from the eye by the starting or corner finishing profile, then a hacksaw is used for wood. If the cut area remains in sight, then use a tool for metal.

When choosing what to cut plastic panels, attention is paid to the convenience of work. When using a hacksaw on wood, the workpiece will vibrate strongly and must be held firmly. And when using tooling for metal, the vibration effect will be little noticeable, but the tool will need to be held almost parallel to the plane of the workpiece. This is due to the thickness of the blade holder, which is larger than the blade..

In both cases, the panel is placed facing the cutting tool so that all chips and imperfections remain on the wrong side..

How to cut PVC panels

Among the variety of finishing materials used in construction, plastic panels occupy a separate category. It is a modern coating that is used for interior and sometimes exterior walls. They are made from polyvinyl chloride by extrusion. Before performing installation work, it is important to decide: what is the best way to cut PVC panels. The range of tools and accessories offered on the market is full of offers, both general and special. Among all the inventory, you can choose what will cut the plastic panels.

How can PVC panels be cut

Plastic finishing material can be cut both lengthwise and across. Of course, the main blanks are cross-cut. When it is necessary for the sewn surface to be completely closed, then it is necessary to use a longitudinal cut. Before starting work, it is determined how to cut plastic panels at home or at an industrial facility. The number of blanks required for wall cladding is of no small importance..

Using many years of experience in the use of PVC materials in interior decoration, we highlight what can be used to cut plastic panels:

• construction knife;
• hacksaw for metal;
• Angle Grinder;
• jigsaw;
• cutter;
• hacksaw for wood.

The use of any of these tools will help solve the question of how to cut PVC panels, but each of them has features that must be taken into account when performing work.

Jigsaw

Using such a power tool will help to cope with cutting panels and reduce labor intensity, compared to a hacksaw or a construction knife. Convenient to use a jigsaw when preparing a large number of workpieces.

When performing work, the place of the cut is first marked on the front surface, and then smoothly cut to the required size, passing the tool along the marking mowing line. Cellophane or other material is placed under the jigsaw support foot, which will prevent the possibility of scratching the PVC panel. In the case of simultaneous cutting of several blanks, they are fastened with plastic clamps or wrapped with transparent tape. At the same time, it is better to isolate the front surface from the adhesive tape (lay a sheet of paper).

Cutter

Such a device is convenient when speed and high-quality cut of the end face of the workpieces are important for solving the problem. The speed of such a tool is high, while the quality is better than any of the ones described above. But, when working, you need to carefully inspect the panel for possible chips and lay it inside out to the cutter, and face down to the supporting surface. This is due to the fact that the cutter can push the surface of the PVC workpiece by 2-5 millimeters..

The tool simplifies and speeds up installation work. Buying a cutter will forever close the question of how to cut off a plastic panel, and other methods will no longer be relevant. When using it, it is important to remember that such a tool will not be able to trim in place with such a tool..

Angle Grinder

To carry out such work, it will be inconvenient to use a large-sized angle grinder, and it is useless. angle grinder of small size with a thin disc for metal (0.8-1 mm), will fit in the best way.

If it is necessary to cut a large number of panels at the same time, they are fastened, markings are applied. The cut is made from the front or back. The end quality is obtained without defects. Such a power tool allows you to cut a panel with high quality or several at once.

Construction knife

In any household, you can find a kitchen knife, sharpen it and use it to solve the problem than to cut off a plastic panel. But, to get a high-quality cut, it is better to use a construction or clerical knife. Replaceable blades, which are supplied with the tool, will allow you to get an even, smooth surface. Cutting with a knife is faster than using sawing devices. But, when you have to deal with the honeycomb structure of plastic panels, the use of such a tool becomes inconvenient..

When using a construction or clerical knife, the panel is marked out, then laid on cardboard or the cut part is left hanging. After that, pushing through the front and back sides of the finishing material, they separate the unnecessary parts. If a large area of ​​unclaimed plastic part remains, then it is better to put or substitute a support under it, in order to avoid kinking or skewing the workpiece.

Hacksaw

One of the universal devices for cutting any material is a hacksaw, which is sure to be found in the arsenal of any craftsman. It is she who will help, if necessary, cut the plastic wall panel. Such work will take longer than using a special cutter, but with significant volumes of cladding, this will not significantly affect the total repair time..

When using a hacksaw, you should listen to the following recommendations of experts:

• for working with plastic finishing materials, you should use a tool with small teeth, which is usually designed for working with metal or wood;
• to shorten the PVC panel, there is no need to apply strong physical forces, which can lead to damage to the material;
• you can cut several parts at once with a hacksaw by folding them in a pile and securing them to avoid bending or displacement.

To prevent the incision from being serrated, it is not recommended to use a tool with teeth set apart in different directions..

Material features

PVC panels are one of the modern types of finishing materials that are made by extrusion and are used both in the bathroom and in the living room. The main raw material in the production of such products is polyvinyl chloride, which is used to fill the mold. To give the panels the desired color, a certain amount of crushed natural chalk is added to their composition..

Decorating PVC panels can be done in one of the following ways:

• staining;
• thermal printing;
• offset printing.

Thermal printing is applied to the plastic surface using a special roller heated to high temperatures, which presses the film to the surface of the product. Thanks to this technology, it is possible to quickly and clearly apply a pattern without losing the brightness of the image. The panel itself does not need additional varnishing. Offset printing is used much less often due to its high cost.

Power tool

For quick sawing of PVC panels, a power tool at hand is best. For this purpose, you can use almost any device, which will help to significantly reduce the time spent on preparing for installation..

Often, cutting is performed using the following devices:

• jigsaw;
• Angle Grinder;
• circulars.

To work with plastic material, it is allowed to use only low revolutions, because with significant heating it begins to melt and release fumes that are toxic to the human body, and the cut in this case will turn out to be torn.

Using a jigsaw will help make the process of preparing PVC panels for installation much faster than using a hand tool.

However, with such a method of processing, the following nuances must be taken into account:

• even before starting work, it is necessary to turn off the pendulum stroke;
• a file with as small teeth as possible should be used;
• you need to set the lowest speed of movement of the file, which will avoid excessive heating of the plastic at the cut.

Using a jigsaw is very convenient to cut stacks of panels, but you should make sure that their height does not exceed the length of the file installed in the tool.

The angle grinder is recognized as the most convenient and practical power tool with which you can cut PVC wall panels. By installing a cutting disc, you can make not only straight, but also curly cuts on the surface of the plastic. When processing plastic in a circle, the angle grinder turns on only at low speeds, which will avoid damage to the material due to melting of the edges..

In the absence of more practical and convenient tools, PVC can be cut with a knife..

To solve this problem, the following types of cutting products are suitable:

• Kitchen knife. This tool is suitable for cutting multiple panels in the process of repairing or replacing them. For large-scale wall decoration, such a procedure is unnecessarily long and painful..
• Construction knife. Among hand-held cutting tools, such a device is one of the best options for achieving a straight cut with relatively little effort..
• Stationery knife. Using a wooden ruler or square, this tool allows you to achieve a perfectly even cut of the panel, therefore, it is often used to cut them.

Choosing a cutting tool

Specialists in the implementation of repair work, who have to carry out the installation of PVC panels in their professional activities, know many secrets regarding the correct cutting of plastic materials up and down. After analyzing them, each owner who wants to make repairs on his own will be able to choose the most suitable professional tool for him or use the tools at hand.

The choice of a method for cutting panels usually depends on the tasks and capabilities of the master. Below are the types of cutting materials.

Cutter

If necessary, this tool can be independently made from available tools, for which it is enough to adhere to the following recommendations:

• it is necessary to prepare a metal strip, the thickness of which is at least 2 mm and the width is 1 cm;
• then one of the edges of the workpiece should be cut off at an angle of 45 degrees;
• it is necessary to sharpen the edge of a homemade product using a grindstone;
• the opposite side should be wrapped with electrical tape, which will allow you to protect your hand from damage during work.

A professional cutter for plastic has a relatively low cost, so its purchase can serve as a profitable investment, because thanks to such a tool, the process of cutting PVC panels becomes not only more convenient, but also quite fast.

Basic cutting rules

So that the efforts on cutting PVC panels are not wasted, and the result of the work meets expectations, experts recommend adhering to a number of rules for working with plastic. These little secrets will help not only to significantly reduce the amount of spoiled material, but also save the master from unnecessary financial expenses and injuries..

When carrying out work during the heated season, do not start cutting panels that have recently been brought into the room. The plastic should naturally warm up to room temperature, which is achieved in at least 12 hours. The fact is that at low temperatures the plastic panel becomes fragile, and therefore it can crack and break off in large fragments..

Regardless of the chosen method of processing the material, it should be placed with its front side facing you, which will avoid deformation of the panel and difficulties during its further installation. When cut from the seamy side, you can find microcracks on the front part, which will manifest itself over time and significantly spoil the interior.

It is necessary to mark in advance the straight line of the planned cut, which can be done with a simple pencil and a stationery ruler.

To speed up the process of preparing the material for installation work, you can cut or saw several PVC panels at the same time. To do this, simply stack them in a pile and create a two-point support. It is best to rest the opposite edge of the stack against the wall, which will help avoid shifting the products, respectively, as a result, parts of the same length are obtained.

How to cut PVC panels?

• Material features
• Choosing a cutting tool
• Cutter
• Hacksaw
• Power tool
• Knife
• Basic cutting rules
• Safety regulations

PVC panel is one of the most popular materials for interior decoration. Its use in the interior attracts not only by its appearance, but also by its affordable price, ease of maintenance and installation. Due to the listed characteristics, many people prefer PVC panels, rather than tiles, when decorating personal hygiene rooms.

Safety regulations

Like working with any building materials, processing PVC panels requires compliance with several safety rules. These recommendations are especially relevant if you plan to work using a tool that is connected to the power supply, for example, a jigsaw or an angle grinder. When cutting plastic with a power tool, there is a great danger that debris and sawdust can fly off the panels. Therefore, experts recommend purchasing safety glasses and gloves in advance, which should not be removed until the end of the work. These seemingly simple personal protective equipment can help keep your hands and eyes safe from injury..

These tips should help you decide on the choice of a tool, as well as create an interior of your own dreams and avoid most mistakes, because with a little effort, you can achieve the desired result, saving a lot of money..

How to easily and clearly cut a plastic panel is described in the video.

How to cut plastic panels? 4 tools to choose from to help

When sheathing the PVC surface, it is required to decide in advance and decide how to cut the plastic panels. Currently, as a decoration for a bathroom or balcony, this material is practically out of competition and is very, very popular..

Someone may object and remember at least a tile, as one of the most traditional finishing materials for bathrooms. Yes, tiles are a classic and a tradition. But PVC is mounted easier and faster, and requires much less maintenance, since they do not collect soap and sediments from the water, in case of damage they can be easily replaced. In a word, tiles are still inferior to the first positions to plastic panels. And if you need to quickly and efficiently sheathe services, now many choose exactly the panels.

First of all, they fell in love with the people for the availability of self-installation. It causes the only difficulty: the standard length of a plank of 3 meters is too great for most apartments. In addition, the height of the ceilings may vary – both due to the errors of the builders, and due to the flight of the owner’s design thought. So the finishing material needs to be shortened, which means it must be trimmed..

How to cut plastic panels has long been invented. And these methods – both folk and modern technological ones – are diverse enough for us to choose: either the method that seems more convenient, or the one for which there is a suitable tool on the shelf. Let’s take a closer look at several of the most popular methods by which this process is carried out. And let’s take a closer look at each of them.

They significantly speed up the process and give a fairly even cut. Practically irreplaceable for longitudinal separation. Like a hacksaw, a stack of panels can be processed – if only its height does not exceed the length of the working surface of the tool.

There is one “but”: at high speeds, the panel begins to melt, which is why the edge turns out to be wavy, and unpleasantly smelling and poisonous substances are released into the air. So the work is carried out exclusively at low speeds..

In addition, you need to carefully measure the effort, since all three instruments are quite heavy and, so to speak, aggressive. Excessive use of them leads to panel breakage. Considering the indicated disadvantages, many craftsmen recommend using a conventional, not electric, jigsaw for cutting. It separates the panels a little faster than a hacksaw, the cut is obtained without creases, is convenient in longitudinal cutting and is safe to use.

When using any tool, some requirements must be met. Moreover, it is in your best interests if you strive to do without work injuries and unnecessary marriage..

Before cutting the panels brought in from the cold, they must be warmed up. The main mistake of inexperienced finishers is to store the cladding on the balcony and bring it in as needed, immediately starting to cut. PVC becomes brittle in the cold, and the cut is fragmented. Cracking is not uncommon almost along the entire length of the panel. So after entering the room, the planks are left to stand at least overnight..

You can cut (again in any way) only with the wrong side down. If you place the panel incorrectly, its profile will fold over and make installation difficult. The panels of some manufacturers may have more significant violations: microcracks on the front surface, which do not appear immediately.

If you are cutting a stack of panels that need to be of the same length, place them on 2 supports so that they do not sag or move. It is advisable to rest the end not cut off against something, at least against a wall. Otherwise, when the tool is applied, the elements will shift and turn out to be of different sizes..

And one more thing: when cutting, it is advisable to use protective goggles. Especially when using a power tool: the probability of a shrapnel flying off into the face area is quite high. And if people are indifferent to scratches on their hands, then an eye injury is much more dangerous. Naturally, it is up to the finisher to choose what to cut the plastic panels with. However, before choosing one tool over the rest, you need to know what difficulties you may encounter when using it. We tried to cover them in full..

How to cut plastic panels: four tools and what to expect from them

What is most often found in the arsenal of any master finisher? Naturally, the most popular tool in the work. Among them there will surely be a razor-sharp knife, a hacksaw for metal, for wood, and perhaps even an electric jigsaw. It is the listed tools that are most often used for cutting plastic panels. All these tools are cut in different ways, but be that as it may, they do it, and the quality of the cut is quite enough for wall decoration.

• Knife. Must be quite sharp and able to cut through one side of the panel in one pass. In fact, in the process of cutting the plastic with a knife, the master cuts only its front surface – then the panel simply breaks, after which the back side is cut off with a knife again. Everything is simple, but the cut itself turns out to be uneven and one side of the plastic is, as it were, bent, which makes it difficult to insert the PVC panel strip into the starting profile or connector. You have to trim everything and achieve a normal edge, spending time on this process.
• Hacksaw for wood. It has large teeth and in most cases does not cut plastic panels, but tears them along the edges. In general, the option is not very successful and it is better to leave it as a last resort, when nothing else is at hand..

How to make a hole in a plastic photo panel

By and large, if you are not confused by the melted edges of the panels, you can cut this material with an angle grinder. Alternatively, a circular saw is also suitable, but for this it will need to be equipped with a circle with a fine tooth. In general, anything will do, but you need to understand that some tools create ragged edges, while others make a clean, but not entirely even cut..

How to Make a Hole in a Plastic Panel: Hole Cutting Tool

Almost every time when it comes to decorating walls or ceilings with plastic panels, one has to deal with the issue of cutting holes in the panels for lamps or for sockets – separate tools are used for them, although in some cases some of those described above can be used. … We’ll leave them for later, but for now we’ll figure out the most suitable options..

Hole saw. Ideal, but it is not always present at hand. The most suitable is a type-setting crown for drywall, which, by changing nozzles, can cut holes of various diameters – you can choose a file for both sockets and recessed ceiling lamps. This tool cuts very carefully, but you need to be careful at the end of the drilling – when the tool falls sharply through the plastic, the main panel can be damaged. At this point, the pressure on the tool must be significantly relieved..

How to cut plastic photo panels

This is with regard to solving the question of how to make a hole in a PVC panel for a lamp or a socket using the basic tools – in addition to them, as mentioned above, you can use the ones described above. For example, a knife – in order for the hole to be even, it must first be drawn with a marker or pen (unfortunately, a pencil leaves a barely noticeable mark on the plastic). In exactly the same way, according to a previously drawn mowing line, a hole can be cut with a blade from a hacksaw for metal, and with an electric jigsaw with a file with a fine tooth.

How to cut plastic panels: features of working with material

The main advantage of any decorative panels is their easy installation, and if we talk about plastic panels, then you can add a very simple processing and adjustment. Plastic is a fairly soft material that can be cut with almost anything – I mean, almost every first cutting tool will do. Despite this, the issue of cutting plastic has its own subtleties and nuances, which, among other things, we will get acquainted with in this article, in which, together with the site stroisovety.org, we will deal with the question of how to cut plastic panels?

How to make a hole in a PVC panel photo

How to make a hole in a PVC panel: the secrets of cutting material

In working with each material, there are some peculiarities – so to speak, subtleties that are used by masters to achieve a particular goal. Regarding plastic panels, among such nuances, the following points can be distinguished.

• Cross cut. In the process of its production, the use of an angle will help create a cut at a clear angle of 90 degrees..
• Longitudinal cut. The simplest cut, since it is made between the inner reinforcing bridges – in most cases is done with a knife. First, the face of the plastic is cut, then the panel is bent and the back side is cut.
• Another interesting point associated with cutting plastic panels lengthwise is the possibility of facing the outer and inner corners without the use of special connecting elements. If the panel is cut from the back, it can be easily bent to form an inner corner. And if you remove the strip between the stiffeners from the back of the plastic, then the panel can be bent in the other direction, thereby forming an outer corner. The only thing to remember here is the fragility of plastic – with sudden movements, thin material can break. Before work, it is better to slightly warm the place of bending with a hairdryer – you can even use a household one.

How to bend a plastic photo panel

And the last point concerns the smooth slitting of plastic PVC panels. If you need to cut it clearly lengthwise, then it is best to make a cut between the internal bulkheads of the panel – first you can cut it as it goes, and only then trim it along the bulkhead. In principle, there is practically no need to make such precise and clear cuts – except when you have to hide the last strip in the starting profile. A clear cut without any burrs is important here..

topics than cutting plastic panels, I will say a few words about the quality of cutting. Do not underestimate the importance of a straight cut when installing plastic panels – you do not need to rely on the fact that the edges will hide behind the starting profile. The fact is that the cut curve is primarily a problem when installing the panel. It is much easier to insert a straight cut strip of plastic. Moreover, when inserting a crookedly cut panel, you run the risk of damaging other elements of the cladding with the tool that you will use to insert the strip into the profile.

How to cut plastic PVC panels

Plastic panels have a number of advantages that make them an indispensable material for quick and inexpensive renovation of bathrooms, toilets, loggias and garden houses. The panels are impervious to moisture, are low-combustible materials, resistant to mechanical abrasion, have a long service life and are relatively cheap. They can be used to decorate both walls and ceilings. The technology of mounting plastic panels is simple and does not require preliminary surface preparation.

One of the essential stages in the installation of plastic panels is their cutting to the required size. The complexity of this stage depends on the state of the surface to be finished: if the wall, for example, is straight and even, then you can prepare the entire volume of plastic panels required for it in advance. If the wall has different heights, complex shapes, or includes architectural elements (windows, doors, ledges, etc.), then you will have to cut the panels along the way, which, of course, significantly increases the installation time.

How to cut plastic PVC panels?

It should be noted that plastic panels are quite easy to process, and they can be cut using a wide variety of tools. Most often, hacksaws for metal or wood with small teeth are used for this. The advantage of this method is that they can simultaneously cut several panels. It is necessary to saw the panel face up, at a slope, avoiding strong pressure. If you use a saw for wood, it is better if it has teeth for cross or mixed sawing, if possible, not set apart – such a saw will leave an even cut without scoring. You can also use a jigsaw, but when cutting, they need to strictly dose the pressure, otherwise the panels can simply break. Some people use an “angle grinder” and circular saws to cut panels to speed up the process, however, in our opinion, such methods have several disadvantages: firstly, plastic is quite fragile and light material, and careless handling of it can lead to the fact that the panel will simply break; secondly, from heating when cutting with a tool at a high speed of rotation, the panels heat up and begin to release toxic compounds.

How to easily cut plastic sheets by hand

There are a few rules to follow when cutting panels. If you brought the panels from the cold, let them “warm up” at room temperature for several hours: cold plastic becomes brittle. Before cutting the plastic panels, mark them to the size you need. It is convenient to do this using an ordinary felt-tip pen – it leaves a well-visible mark on the panel and is easily erased. Safety precautions must be observed when cutting panels. It is advisable to wear protective goggles and gloves. Remember that when the panels are broken, sharp splinters are formed, which can injure yourself..

How To Cut Acrylic Sheet By Hand