Home »Stihl 180 Chainsaw Ignition Adjustment
Related posts
Do-it-yourself Stihl chainsaw repair
The Stihl chainsaw, and specifically the MS 180 model, is used to a greater extent for harvesting wood and performing various work systems. Stihl 180. Stihl 180 chainsaw ignition adjustment. Stihl 180, video. Similar equipment is used very often due to the large list of functions and abilities. The main feature of this model is reduced vibration, which is very vital. Naturally, in the process of using the chainsaw it may fail, which means that you will have to do its repair.
Carb problems
A feature of the Stihl chainsaw carburetor is the presence of the 1st screw, which is responsible for setting the idle speed. In the process of operating equipment, it is always necessary to pay attention to idle speed. To adjust this, a few simple steps will help: checking the air filter, as well as the spark protection grille.
It is worth noting that repairing the Stihl chainsaw carburetor is considered a time-consuming process. The article describes in detail the adjustment of the spark plug for the Stihl 180 chainsaw. If, for some reason, it stops starting, you must do the following:
- open the gas tank cap and then close it;
- remove and dry the candle;
- ventilate the combustion chamber.
If such actions are unsuccessful, pay attention to the air filter of fuel supply and the functioning of the spark plug. If, in your opinion, the problem was caused by a malfunction of the carburetor, then a chainsaw purchased with a guarantee is best to immediately return to the service. This is because disassembling it yourself is quite difficult.
Ignition System Check
Read the same
For various equipment breakdowns, it is always necessary pay attention to the spark plug. In this case, the ignition repair of the Stihl 180 chainsaw is required. Ignition adjustment. 3 adjusting the Stihl 180 chainsaw for setting idle speed. To do this, neatly connect the wires, and then turn the element out using the appropriate key. Then you need to evaluate the condition of the candle.
- If it is dry, then this indicates a lack of fuel in the cylinder. Accordingly, the problem is not related to the candle.
- In the case when such an element is splashed with fuel, it is worth making sure that the carburetor is started correctly. The same applies to adjustment. The candle itself is gently wiped, and then the gas supply is shut off and the starter is started. This will help get rid of excess fuel and at the same time ventilate the combustion chamber. After that, the candle is screwed into place and the mechanism is again started.
- If black carbon is visible on this element, then, most likely, low-quality oil was used in the process of using the Stihl chainsaw. Also, the cause may be an incorrect fuel-oil ratio or incorrect carburetor adjustment. ignition adjustment from a chainsaw adjustment disassembly of a Stihl 180 chainsaw. In this situation, the candle is carefully washed, then the carbon is removed with a sharp knife or needle and the electrodes are wiped. In the process of checking the candles, it is important to make sure that the distance between the electrodes is not more than 0.5-0.65 mm.
Ignition installation Stihl ms180
How to adjust carburetor Stihl ms 180 what are the revolutions of min and max? And also a similar video about the adjustment on mine.
STIHL MS 180 HOW TO ADJUST THE CARBURETTOR How to adjust carburetor STIHL chainsaw MS 180
Video talks about simplicity adjustments Magneto gap using the wall of a plastic bottle. Repairs.
As mentioned earlier, when viewed from a candle you can notice black soot. In this case, experienced craftsmen recommend checking if a spark occurs. For this purpose, the ignition cable is fixed on the candle, after which the nut and cylinder are connected using pliers. Do-it-yourself Stihl 180 chainsaw repair. chainsaw ignition system. Adjustment. Then it remains to start the chainsaw starter. If the spark does not occur, you will have to replace the spark plug. In a situation where the use of a new element is also inconclusive, it is necessary to check the high-voltage wires and the connection to the candle.
Repairing the fuel system
Read the same
During the operation of the Stihl chainsaw, some people complain that fuel stops entering the cylinder. Adjustment As soon as the ignition is working, adjust the carburetor of the Stihl 180 chainsaw. A similar problem may occur due to several reasons.
- The filter is dirty. In this case, remove the hose and pay attention to the fuel stream. The filter itself is carefully cleaned or replaced with a new one. For preventive purposes, it is recommended to replace this element every 3-4 months.
- Clogged breather. Description of common malfunctions of a Stihl 180 chainsaw carburetor adjustment. Disconnecting the hose will help ensure that the cause of the malfunction is precisely this. If a blockage is found, use a needle or other small sharp object.
- Lack of fuel or lack of fuel. In the case of the Stihl 180 chainsaw, at the place where the screws are installed, the ignition adjustment is stihl 180. This occurs due to clogged filter. Separately, it is worth mentioning the incorrectly adjusted carburetor of the chainsaw. To eliminate the malfunction, it is recommended to perform the adjustment again using the appropriate screw.
To ensure that fuel always enters the cylinder, clean and replace the fuel filter periodically. You also need to make sure that the hose with the drive fits snugly, and the membrane is not damaged.
It is worth noting that for the proper functioning of the Stihl chainsaw, you need to choose high-quality fuel. At the same time, its quantity must comply with the norm recommended by the manufacturer
Chainsaw Stihl MC 180. fairly simple unit. Despite this, equipment repair often causes many difficulties, because one malfunction can occur due to a large list of reasons. Accordingly, before you decide to start the repair, accurately diagnose the breakdown.
In this review, we will try to solve the problem that many owners of chainsaws present to your attention. In the process of using such a tool, the consumer may encounter a situation in which it is necessary to correct the ignition timing. Over time, the breaker can fail, the coil is also not eternal, although it serves much more and it is quite difficult to disable it. So let’s figure out how to set the ignition on a chainsaw.
Structural components
All engines, whether automotive or other tools using an internal combustion engine, have similar operating principles.
No exception there are such eminent chainsaws and are used with pleasure by consumers like Goodluck, Stihl or Husqvarna.
The drive to them is a familiar internal combustion engine, respectively, a fuel tank, an engine and a working body that produces direct work, as well as other mounted organs that help in managing.
Video: How to Configure Ignition Stihl 180
Sometimes during operation some problems may arise, in this rather reliable tool like a chainsaw.
The question is, what then to do?
Here are some common cases:
- A chainsaw will not start;
- If it starts, it works intermittently;
- Not enough power for proper operation.
Ignition
The main problem in this group of problems is the engine.
Ignition is one of the main elements affecting the tool uptime. Therefore, the first to consider this particular block.
The time has passed when the ignition control was engaged in a breaker with cams and a moving contact, which supplied a spark to a candle.
This was not a very reliable system due to the many elements that influenced the operation of the engine. A chainsaw with invisible malfunctions could simply stop starting up. And we could observe a picture of constant tugging at the lace of the factory. To date, manufacturers have switched to contactless ignition systems.
They have fewer moving parts and no contacts that need to be periodically exposed, often failing. The coil used on a modern chainsaw will work until the end of the service of your tool. A chainsaw has become much more reliable and easier to maintain.
Possible malfunctions
If the saw does not start, the first thing to check is a spark giving a spark that ignites the fuel in the cylinder. Start by removing the high voltage wire to which the candle is connected. Then unscrew the candle itself from the cylinder cover and inspect its condition. A candle should work dry and light deposits on light-colored ceramics:
- If the candle is wet, then there are problems with the carburetor. It is necessary to adjust and set the fuel level in it;
- The soot on the walls of the candle is dark or black, means a malfunction in the piston group.
If you have not found any visible causes of the malfunction, the candle is dry, light carbon deposits continue to go from the opposite. Since this is the final point of ignition of the working mixture. Now check to see if the spark comes to the candle. This is the ignition system unit.
Check whether there is a spark will not be a particular problem, for this it is enough to take the high-voltage cable to which the candle is connected, bring it to the cylinder block by setting a small gap between them, so that you can notice a spark jumping between them. Then we pull the starter’s starter cord and see if there is a spark and what color it is. A working, working candle should give a spark similar to lightning. What it looks like, look at the photo offered to your attention, everything is clearly visible on it.
If no spark is observed, check with a control light; if there is no probe, the high-voltage cable. A cliff is possible in the place where it was bent most often. If the wire is in order, it is possible that the problem is in the incorrectly set ignition angle. It may be too early or too late in both cases, the chainsaw starts well and will not work.
Now let’s try to set the correct gap between the movable and fixed contact. Ideally, it should be 0.2 mm. You can check with a probe, since it is not a deficit.
This was a description of the malfunctions of the older generation of chainsaws. The new generation includes modern Goodluck, Stihl and Husqvarna chainsaws.
Modern systems
Modern systems are equipped with chips that regulate all of the above problems. A method for independently setting the ignition timing depending on the engine speed and the power transmitted to the cutting element. At the same time, fuel is saved significantly without sacrificing power. Starting the saw is also much easier regardless of weather conditions.
The chainsaw itself has become simpler and more efficient and does not require expensive repairs. Ignition coils made using modern technology and using new materials have literally become eternal.
In addition to everything read, a video is offered here for a complete familiarization with the material provided.
2 comments on the record “How to set the ignition on a chainsaw”
I bought a Stihl chainsaw, it practically did not work. just repairing. I can’t start it.
how set the ignition on a chainsaw
In this review submitted your attention try to solve the question that arises among many owners of chainsaws. In the process of operating such a tool, the consumer may encounter a situation in which it is necessary to adjust the ignition timing. Over time, the breaker can fail, the coil is also not eternal, although it serves much more and it is difficult to disable it. So let’s figure out how set the ignition on a chainsaw.
Structural components
All engines, whether it’s a car or another tool using an engine internal combustion have similar working mechanisms.
Not an exception, there are such eminent chainsaws and are used with pleasure by consumers like Goodluck, Stihl or Husqvarna.
The drive to them is a familiar engine internal combustion, respectively, a fuel tank, an engine and a working body that produces specific work, as well as other suspension organs that help in managing.
From time to time in the process of use, some obstacles may appear, in this rather reliable tool as chainsaw.
The question is, what then to do?
Here are some common cases:
- Chainsaw does not start;
- If it starts, it works intermittently;
- Not enough power for proper operation.
Read the same
Ignition
The main problem in this group of problems is the engine.
Ignition one of the main elements affecting the uptime of a tool. Therefore, the first to consider this particular block.
The time has passed when the ignition control was engaged in a breaker with cams and a moving contact, which supplied a spark to a candle.
This was not a very reliable system due to the many elements that influenced the operation of the engine. Chainsaw with invisible malfunctions, it could just stop starting up. And we could observe a picture of constant tugging at the lace of the factory. To date, manufacturers have switched to contactless ignition systems.
Ignition Stihl ms180
Allows you to correctly determine the situation when, when disassembling and replacing the module ignition necessary put up.
Assembly STIHL MS180
Stihl, Briggs Stratton. pavel@mechanic.kiev.ua
They have fewer moving parts and no contacts that need to be periodically exposed, often failing. The coil used on a modern chainsaw will work until the end of the service of your tool. Chainsaw became much more reliable and easier to maintain.
Possible malfunctions
If the saw does not start, the first thing to check is a spark giving a spark that ignites the fuel in the cylinder. Start by removing the high voltage wire to which the candle is connected. Then unscrew the candle itself from the cylinder cover and inspect its condition. A candle should work dry and light deposits on light-colored ceramics:
- If the candle is wet, then there are problems with the carburetor. Need to adjust and put up fuel level in it;
- The soot on the walls of the candle is dark or black, means a malfunction in the piston group.
If you have not found any visible causes of the malfunction, the candle is dry, light carbon deposits continue to go from the opposite. Since this is the final point of ignition of the working mixture. Now check to see if the spark comes to the candle. This is the ignition system unit.
Read the same
Check if there is a spark will not be special problems, for this it is enough to take high voltage cable to which the candle is connected, bring it to the cylinder block by setting a small gap between them, so that you can notice a spark jumping between them. Then we pull the starter’s starter cord and see if there is a spark and what color it is. A working, working candle should give a spark similar to lightning. How it looks, look at the photo suggested your attention, everything is clearly visible on it.
If no spark is observed, check with a control light; if there is no probe, high voltage cable. A cliff is possible in the place where it was bent most often. If the wire is in order, it is possible that the problem is in the incorrectly set ignition angle. It may be too early or too late in both cases. chainsaw starts well, and will not work.
Now try put up correct clearance between movable and fixed contact. Ideally, it should be 0.2 mm. You can check with a probe, since it is not a deficit.
This was a description of the malfunctions of the older generation of chainsaws. The new generation includes modern Goodluck chainsaws, Stihl and Husqvarna.
Modern systems
Modern systems are equipped with chips that regulate all of the above problems. A method for independently setting the ignition timing depending on the engine speed and the power transmitted to the cutting element. At the same time, fuel is saved significantly without sacrificing power. Starting the saw is also much easier regardless of weather conditions.
In addition to everything read, a video is offered here for a complete familiarization with the material provided.
2 comments on the entry “How set the ignition on a chainsaw ”
I bought a Stihl chainsaw, it practically did not work. just repairing. I can’t start it.