How to correctly thread a trimmer line into a brushcutter

How to properly wind the line for the trimmer on the grass trimmer: step-by-step guide and video instructions

A beautiful lawn will only look really well-maintained if the grass is regularly mowed. The grass trimmer is best suited for processing complex areas. Any owner of the machine sooner or later will be faced with the problem of how to wind the line for the trimmer on the spool, because the wrong actions can not only worsen the quality of mowing, but also withdraw the equipment from service. Today in our review of Homius we will tell you about all the ways and nuances of replacing the line and the peculiarities of the choice of consumable material.

Grass trimmer is useful for mowing small or difficult areas, such as near the hedge, between the beds and along the paths. Today, manufacturers produce a large variety of gasoline, electric and battery-powered models, which can be selected for any needs of owners.

Grass trimmers use a trimmer blade as the cutting element. Sooner or later the length of the thread will run out, and then the proprietor will ask how to properly replace and secure the thread inserted in the detachable spool.

What to consider when choosing a fishing line

Before inserting and fixing the line for the trimmer in the removable reel of the grass trimmer, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Overview of manufacturers and models, as well as useful tips from the experts reviewed in this review will help in the difficult choice among the many models of devices.

By quality

Before you put a grass trimmer line on your trimmer, you need to pay attention to the cross-section of the cord:

• Strands with a circular cross-section are the most common option. They are excellent for mowing grass, even in difficult areas;
• spiral trimmer line is suitable for thin grass. It is not very strong and will not be suitable for old thickets;
• cord with serrations and sharp edges is chosen for mowing weeds;
• The line for the trimmer with a variety of geometric sections will help mow the lawn more evenly, but the durability of the consumable is not high.

Important! The most wear-resistant consumable material. it is a two-component line for the trimmer with a round section, reinforced on the inside.

The owner of a brushcutter must know that it is strictly forbidden to use wire made of metal, fishing line and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electric trimmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

By size

Before you wind the thread on the grass trimmer spool, you should pay attention to its size. The most commonly used trimmer line is 2 mm.

You can find the right diameter in the following ways:

• View the recommendations in the manufacturer’s instructions to the trimmer.
• Often manufacturers indicate the cross section on the bobbin.
• The diameter of the bobbin must match the diameter of the bobbin hole.

Important! The thicker the thread is, the harder the grass it can mow.

Features of trimmer application

grass trimmer mowing with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flowerbeds, rows in the garden.

Such a convenient, and most importantly, effective device as a trimmer for grass, there are several variations:

As is clear from the names, the types of grass trimmer noticeably differ from one another. But regardless of the type of this tool, its cutting element may be a line for a trimmer. Of course, the line in the reel of the grass trimmer is not endless. And sooner or later it will be necessary to replace it with a new one.

Consumption of fishing line directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the grass trimmer, the more the trimmer line is used. And, accordingly, the faster it will run out. In this connection, the question arises: how to tuck the line for the trimmer into the grass trimmer reel?

Not everyone knows the answer to this question. And after all, the winding of the line on the spool plays an important role in the work of the grass trimmer. In order for the device to function properly, it is very important to properly wind a new line for the trimmer on the spool. On how to change the line for the trimmer on the trimmer, and will be discussed in this article.

Which line to choose for your trimmer

Before you stock up on this material to put in your grass trimmer, you need to decide on a choice of. After all, the usual so-called round line for the trimmer is not the only type that exists. So how to choose the right line? You first need to determine the working conditions.

Choice by type. A line for trimmer with a round section is the most common. It will fit any bobbin, with very few exceptions. This type of expendable material is suitable for mowing fresh, succulent grass. But it is not possible to cope with mowing the so-called dead wood with this kind of threads. It is pointless to even mention attempts to mow bushes with this line.

In addition to the usual type there are others with sharp edges. They are usually designed in “star” or “square” patterns. The presence of sharp edges is the main feature and the key difference between these threads.

It is because of this feature that the threads of these types are able to mow dry weeds. But sharp-edged threads are not without disadvantages, the main of which can be called rapid wear and durability, which is noticeably inferior to the round type.

In addition to the already mentioned types of fishing lines, there are other interesting and common varieties. Particularly noteworthy among them are fishing lines, inside of which there is a metal wire. This type of thread is often used in gasoline-powered tools with an engine more powerful than one and a half horsepower.

Filaments with a metal core are available both with a round section and with sharp edges. Regardless of the cross section type, such filaments are the best for overcoming hard-to-cut plants. Threads of this type can easily cut not only dry grass, but even small bushes.

Filaments with wire inside compare favorably with other mowing implements due to their incredible durability. But unfortunately, this feature has more than a noticeable effect on the price of this type. The cost of filaments with a core is much higher than other types of filaments.

Choice of thickness

You should also pay special attention to the thickness of the material. For mowing young grass, a thread with a diameter in the range of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and rougher the weeds it can handle.

There is a “but” in choosing the thickness of the line. It’s important not just to assess the material’s capabilities, but also to take into account the grass trimmer’s features. Be sure to check the owner’s manual that came with the tool to find out what the requirements of the cutting element are.

Use of unsuitable thread can cause tool failure. Using too thick thread will overload the motor of the unit. And using too thin a thread will increase the wear and tear of the torque mechanism many times over.

That is why it is necessary to approach the choice of consumable material not less responsibly than to its filling in the grass trimmer. When a suitable line for the trimmer has been found and purchased, you can begin to consider how to wind it on the spool.

Removing and disassembling the spool

In order to properly wind the line for the trimmer on the grass trimmer reel, it is necessary to get acquainted with the structure of the trimmer head. It consists of a protective cover, a bobbin with thread, a housing cover, and a spring, which is only present in some devices.

When proceeding to disassemble the coil, it is necessary to completely turn off/disconnect the device. The method of operation directly depends on the type of head. The first option is to carry out the following actions:

• The user presses the latches located on both sides of the cover.
• After removing the cover, the bobbin is removed. Some models may contain a spring, which must also be removed.
• There is a screw in the middle of the housing that can be unscrewed using a normal screwdriver.
• When the fasteners are removed, it remains to remove the reducer from the shaft, gently rocking the body of the product.

The second option for removing the spool for threading the line in the grass trimmer is to screw the head onto the gear shaft. To accomplish this procedure, many devices are equipped with a hole into which a tool can be inserted. When the screwdriver is inserted, the user has only to take hold of the body of the product and twist it clockwise. It is noteworthy that this method, unlike the previously described method, is characterized by the simplicity of execution.

Winding the fishing line

Inserting the trimmer line into the grass trimmer is not difficult. To perform this operation, it is necessary to follow a simple algorithm of actions. The first step is to determine how much consumable material is enough. To make its calculations, it is necessary to wind the line for the trimmer on the spool so that the resulting coil was less than or equal to the diameter of the sides of the structure.

When you have decided on the size of the cord, you need to fold it in such a way that one part of it is 15 cm longer than the other. Winding the cord begins from the side that divides the bobbin into 2 parts. Here will be located the attachment, in which you need to insert the thread, bent in half.

Now it is necessary to understand in what direction to tuck the line for the trimmer in the grass trimmer. To do this, inspect the bobbin. often a special arrow is indicated on it. If no explanatory information is available, find the indicator on the trimmer head and start winding in the opposite direction. Further actions can be divided into 4 steps:

• Finishing winding the cord. To do this, it is inserted into the side groove on the reel. Attach its other end to the opposite groove.
• The ends of the fixed fishing line are cut. There are 7-10 cm of allowances left over.
• The filled part is placed in the head of the grass trimmer. This is done by alternately inserting and pulling the thread into the inlets of the structure.
• The thread is pulled out of the groove. Once the action is completed, the product cover is secured with the clamps.

Once the last step is complete, the garden tool is ready for use. If after inserting the line into the grass trimmer the device does not work correctly, it is recommended to repeat the procedure, changing the thickness or type of cord. Otherwise the product can be damaged.

How to remove the coil from the grass trimmer?

To change or rewind the cutting thread on the spool, it must be removed.

How difficult it is to remove depends on the tool model:

• The low-mounted tool. The motor is almost on the ground. To remove the reel, you must press the buttons on the side of the grass trimmer. After pushing these buttons, the body where the line spool is located opens.
• Grass trimmer with bent boom. Here you need to turn counterclockwise the special knob. After that the spool and the spring in it are removed.
• Tool with straight spool. The rod is held stationary with a screwdriver or other object. Turning it clockwise removes it. After that, take the tool apart and remove the reel.

• If the tool with a single tendril is used, you will need about four meters of thread. This thread is passed into the hole inside the spool, where it can be fixed. Then one end of the fishing line is guided by the arrow. Then the end of this thread is secured in the groove that is in the reel. This is to prevent the thread from unwinding when assembling the spool. In the absence of grooves, you should hold the line for the trimmer with your hand and assemble the bobbin.
• If you use a tool with two tendrils, then first check the number of available grooves.If there is one groove, then two tendrils will be facing the same groove. If there are two grooves, each tendril will be directed into its own groove.

In the first case, the right amount of cutting thread is passed through the hole so that the result is a thread of equal length. Then you have to twist the bobbin on the arrow. Then start to assemble the tool, holding the thread with your finger.

If the reel is equipped with a semi-automatic mechanism, wind the line for the trimmer as follows:

• The thread is threaded through the hole that is inside;
• Fasten the ends of the thread in the grooves on the body.
• The reel is assembled and a special button is pressed;
• After which the line for the trimmer itself begins to coil in the desired direction.

Always remember that the cutting line must be protected from hard things. This will extend its life.

If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread for a new.

How to tuck the line for the trimmer into the grass trimmer reel

To change the line in the trimmer, cut a piece of material of the right size by folding it in half. One of the halves should be 5-10 cm longer than the other half.

To properly wind the line for the trimmer on the reel, the middle of the thread, folded in a loop, must be placed in the groove of the central divider. One half of the fishing line is tightly wound on top of the part, the other half on the bottom. The longer part is wound onto the lower part. The winding is in the opposite direction to the head’s direction of rotation. There must be an arrow on the cover or on the side of the mowing head to show the direction of rotation. Reel the line in the opposite direction to the arrow on the spool. Do the work carefully, pressing the coil tightly against the coil.

Insert the other 10-15 cm ends in the slots on the top edge of the spool, this will lock them in place. The coil will not unwind with the ends secure.

If you don’t have the right length of line, you can reel in two pieces instead of one. In this case, bend the end of the fishing line with a hook and insert it into the slot in the center divider of the reel. Do the same with the second piece. Now wind first one piece and then the other on your halves of the spool against its direction of rotation.

To tuck the fishing line into the grass trimmer, insert the ends into the holes in the mowing head and pull them out. Put the spool on the axle and push it down so that it sits in its place and pull the ends of the cutting filament again to pull them out to their full length.

The blade tip should reach all the way to the blade guard. Cut off any excess. To do this, you can use the steel plate installed on the hood, which acts as a knife and automatically cuts the line for the trimmer of excessive length when unwinding the head.

The reel is covered by the protective cap. Push it in place and push down until the catches click into the grooves. Always check that the cover is in place on the grass trimmer and that the latches click into place, otherwise it could come off during operation. At this point the bobbin will be ejected by the rotation of the bobbin.

Do not try to reel in as much material as possible, otherwise the reel may not fit and you’ll have trouble installing and locking the cover. It is best if the spool is filled with fishing line so that it does not extend beyond the dimensions of the part.

In addition to mechanical double-blade mowers, there are also single-blade models. Their difference is that the cutting thread is derived only from one side. The reel in these types of mowers may not have a central partition, instead of it a slit in the lower flange is used to install the nonworking end of the thread, in the upper flange there is also a slit to fix the working end.

With a replaced line you can start working. Do not cut through thick weeds or brush twigs. this is not a job for a grass mower. To prevent injuries and line breakage make sure no stones or branches get under the mower.

For mowing lawns, one filling of a spool of reinforced line is enough for an area of 400-600 m2.

After the cutting filament has worn out as a result of operation, turn off the mower and remove the cover on the mowing head. Pull the line out of the slot and insert it into the slot. The amount of material wound on the reel is enough for 5-10 cycles depending on the model. When you will install the cover in place, look carefully whether the grooves where the clips are inserted are not clogged, if they are, then carefully clean them.

When the trimmer line is worn out, you need to disassemble the mowing head again, pull out the spool and rewind the working trimmer line on it.

How to tuck a line for your trimmer into the grass trimmer reel

To replace the fishing line in the trimmer, cut a piece of material of the right size by folding it in half. One half must be 5-10 cm longer than the other.

In order to correctly wind the line for the trimmer on the reel, the middle of the thread, folded in a loop, must be placed in the groove of the central partition. One half of the fishing line should be tightly wound onto the top part and the other half onto the bottom part. The longer piece is wound onto the lower one. Wind it in the opposite direction to the direction of rotation of the head. There must be an arrow on the cap or on the side of the head to show the direction of rotation. The fishing line must be wound in the opposite direction of the arrow. Do the work carefully, firmly pressing the coil to the coil.

Insert the remaining ends, 10-15 cm long, in the slots on the top edge of the reel, this will secure them. With the ends tucked in, the reel won’t unwind.

If you don’t have enough line of the right length, you can wind two lines instead of one. In this case, bend the end of the fishing line with a hook and insert it into the slit in the central partition of the bobbin. Do the same with the second piece. Now wind one piece and then the other on your coil halves against the direction of rotation of the coil.

To thread fishing line into your grass trimmer, insert the ends into the holes in the mowing head and pull them out. Put the spool on the axle and push it down so that it sits in its place, and again pull on the ends of the cutting thread to pull them out to their full length.

The thread should reach almost right up to the edge protector. Cut off the excess. To do this, you can use the steel plate installed on the cover, which acts as a knife and automatically cuts the line for the trimmer of excessive length when unwinding the head.

The bobbin is closed with a protective cover. Put it in place and push it down until you hear a click sound from the catches in the slots. Always check that the brushcutter cap is correctly installed and locked in place, or it may pop off while working. If so, the coil will be ejected by the spinning action.

Do not try to wrap as much material as possible, otherwise the spool may not fit and there will be problems with fitting and fixing the cover. It is better if the spool is filled with wood so that it does not exceed the dimensions of the part.

In addition to mechanical double-bladed scythes, there are also single-bladed models. They differ in the fact that the cutting thread is led out on one side only. Reel in these types of braids may not have a central partition, instead of it for the installation of the non-working end of the thread is used a slot in the bottom flange, the upper also has a slot for fixing the working end.

With the replaced fishing line, you can begin to work. Do not mow very heavy weeds or brush twigs. this is not grass cutter work. To prevent injuries and line breakage make sure that no stones or branches get under the line.

For lawn mowing, one refill of a rearmed line reel is enough for an area of 400-600 m2.

After the cutting line has worn out as a result of operation, turn off the mower and remove the cover on the mowing head. Pull the line out of the kerf to the correct length, and reinsert it in the kerf. The amount of material wound on the reel is sufficient for 5-10 cycles of operation, depending on the model of the device. When replacing the cover, check carefully that the catch grooves are not blocked.

When the trimmer line is worn out, you need to disassemble the mowing head again, pull out the spool and rewind the working trimmer line on it.

How to wind the line?

The order of winding the line depends on the type of spool. with one or two tendrils, and with automatic cord charging.

On a single-tendon spool

It’s easy to spool fishing line onto a single-tag reel. These designs, depending on the brand of grass trimmer, holds from two to five meters of cord. The edge of the line in the bobbin should be tucked into a special hole or groove, then the string is wound in the opposite direction to the rotation of the spool during work.

Tip! To understand which way to wind the thread, you should look at the body of the bobbin. usually there are marks on it indicating the direction of the bobbin’s movement when working.

After the line for the trimmer is wound, you need to leave a small piece (15-30 cm), put it through the bobbin outlet and reassemble the head.

on a spool with two spool strings

In this type of bobbin, you need to inspect the inside of the bobbin and determine the number of grooves for winding the cord provided in it.

Important! If there is one groove in the spool, then both tendrils must be wound along the common groove, if there are two. then along separate tracks.

For winding it is necessary to take a piece of fishing line of two to three meters in length. For single groove bobbins, tuck the trimmer line into the through hole, align the whiskers, align it and wind it onto the bobbin in the opposite direction of its rotation when working. If there are fixing grooves, you must put the ends of the cord in them, then pull them into the outlet hole, then close the spool and put it in its previous place.

For double groove bobbins the difference is that a piece of string should be folded in half. Next, you need to charge the middle of the bend in the groove between the grooves, and then wrap each of the pieces of line on its track, fix the tendrils and reassemble the bobbin the same way as a bobbin with one track.

On a trimmer head with automatic threading

With auto-reel heads, all you need to do is thread and pinch the line and the tool will wind the line as you turn it on. It is impossible to make a mistake here, because the coil itself recognizes how the tendrils should be located.

Just a side note! The advantages of trimmers with such a head include the convenience of laying the cord, and the disadvantages. expensive and difficult to repair.

How to insert a fishing line into a grass trimmer?

Filling mowing spool cutting filament for grass trimmer. an easy task, but beginners gardeners will have to practice a little, so that later to be able to quickly insert the cord in the existing household trimmer for grass.

There are only a few ways to prime the grass trimmer’s mowing head. The first method is the easiest and is well suited for beginner gardeners.

In this case, the cord is inserted into the spool in this sequence:

• First, you need to wind about 6 m of grass trimmer line from the common spool, and then cut the resulting section in half. The result should be two strands, each 3 meters long;
• Then on one of the ends of the first section will need to make a kind of hook, and insert it into one of the through holes located at the top of the bobbin;
• Next, begin winding the line on the bobbin in the direction indicated by the arrow. During winding it is necessary to trace, that a line for a trimmer evenly laid on a surface of a bobbin, and did not extend beyond its top section. It is not necessary to wind the section to the end, about 15 cm of thread should remain in your hands;
• The remaining loose end of the wound cord will need to be inserted into one of the notches located at the top of the bobbin;
• Then the same procedure should be done with the second piece of fishing line. It will need to be wound onto the lower section of the bobbin;
• As in the first case, it is not necessary to wind up the line for the trimmer on the lower section to the end. The remaining piece of thread will need to be inserted into the second slot of the bobbin.

Once this is done, the spool must be mounted on the grass trimmer and started. To check the reliability of the thread attachment, you will need to press the throttle lever to the end, so that the engine has reached maximum revolutions. If the line for the trimmer does not fly out of the head, it means that the line for the trimmer is held securely, and it will not fly out of the mowing spool while cutting the grass.

How to wind a line for a trimmer spool for grass trimmer?

The second method is a little harder to do on your own.

Wind the cord for the grass trimmer should be in the following order:

• First you will need to cut from a total of about 6 m of cord, and bend it. In this case, one of the parts should be slightly larger than the second;
• Then the thread by the place where it was bent will need to be inserted into the recess located on the separating edge between the two sections of the bobbin. As a result, the first part of the segment should be in the upper, and the second. in the lower section of the bobbin;
• Then start winding up the line. This should be done in the direction of the arrow indicated on the body of the bobbin. Do not bind the cords during wrapping. The upper part of the segment should be neatly wound onto the upper section and the lower part should be wound onto the lower section of the bobbin. After that, two 15-cm sections of cord should remain free;
• Then insert the remaining ends into the recesses at the top of the bobbin;
• Then the secured ends must be slipped through the holes in the grass trimmer’s mowing head.

At the end you will need to connect all parts of the mowing head, and pull each end of the line slightly toward you. The finished spool will need to be installed on the grass trimmer and continue to work on the site.

Tips

Working with such equipment, as trimmers for grass, requires caution and attentiveness. Implementation of safety measures during work is mandatory for beginners and experienced craftsmen. It happens so that self-confident mowers lose their vigilance, make irreparable mistakes and get seriously injured. That’s why it’s important when working with the machine

• Close the reel cover on all latches.
• Do not reel in more line than necessary: it is hard to unwind later.
• After refilling the spool it’s essential to check that the tool works before mowing.
• Choose quality material that is suitable for the particular trimmer.

You should not try to mow rough grass with thick stems with a fishing line. There are steel discs for this. Wear protective clothing only. Wear safety glasses and proper footwear.

Coiling the line

Unhurriedly complete disassembly of the bobbin spool without losing any of its parts allows you to proceed to the main task. reeling in the line. The technological features of the bobbin design and the number of working tendrils determine the sequence of actions.

Reel with one operating clamp

The easiest option and uncomplicated sequence of operations:

• The size of a reel and the length of an original factory reel determine the recommended length of line for winding. 25 m.
• One end of the line is inserted into the fixing technological hole inside the bobbin.
• The line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer. usually an arrow on the inside of the reel indicates in which direction the line is wound.
• Small part of line is left free for its conclusion outside. it is fixed in a specialized groove on the inside of a bobbin, designed for holding a spool at assembly of a bobbin in working condition.
• The leftover end of the line is fed through the hole in the outer part of the spool.
• The bobbin halves are assembled and put on the rod of the trimmer.

Reel with two operating tendrils

In this type of bobbin, you should determine the number of grooves for winding the line lying on the inside of the bobbin:

For both cases, a 2-3 m trimmer line is taken. One-cable spools have a line for trimmer through the hole, its ends (tendrils) are put together and aligned then spooled to the opposite side of the bobbin rotation direction. inside there is an arrow that usually shows the correct winding direction. If there are fixing grooves, the ends of the fishing line are put through them or held by the fingers of a free hand, put through the through hole of the outer half of the bobbin, the bobbin is closed and attached to the rod of the trimmer product.

The difference of line winding in double-groove spools is that originally a 2-5 m section of line is folded in half (to define the middle fold), and a loop of the fold is inserted in a special groove between the grooves. both tendrils of the fishing line are wound each along its groove, the fixation of tendrils and spool assembly is similar to the above version with one groove.

Doing this procedure for the first time may seem lengthy and quite time consuming, but with time and experience this task will be much faster and easier.

The video below will clearly show you how to tuck the trimmer line into the grass trimmer spool and wind it up correctly. this operation is nothing complicated and with some patience it will definitely succeed:

After the cutting line is worn out as a result of the work, turn off the mower and remove the cover on the mowing head. Remove the fishing line from the slot by pulling it out to the desired length and reinsert it into the slot. The amount of material wound on the reel is enough for 5-10 cycles of work, depending on the model of the device. When you will install the cover in place, look carefully whether the grooves where the clamps are inserted are not clogged, if they are clogged, carefully clean them.

When the trimmer line is worn out, you need to disassemble the mowing head again, take out the spool and rewind the working trimmer line on it.

The grass trimmer is the most common tool used for cutting grass and small shrubs. The machine is easy to operate, simple to operate and thanks to its low weight even women can cope with it. It is no secret that for quality work on mowing the grass, you need the right selection of cutting tools. As the latter, trimmers use special cutting nozzles (discs, knives) or trimmer heads with fishing line inside. Nozzles and fishing line for trimmers. this is an expendable tool, but if the knives can be sharpened, then when the consumption of the line is required to replace it. In this article we will tell you in detail about how to change the line for your trimmer.

How to remove the spool and replace the line for the trimmer

Trimmer owners, mostly beginners, get confused, bordering on panic, when it becomes necessary to change the cutting tool or the line for the trimmer in the reel. Very often, when trying to unscrew the mowing head, users simply bring it into disrepair, not realizing that it unscrews in the opposite direction. To prevent this from happening if a tool needs to be replaced, it is recommended that you read the step-by-step instructions below.

• Before you tuck the line for trimmer in the coil, stop the engine trimmer or trimmer etletricheskogo disconnect to avoid injuries that can occur when accidentally starting the rotation of the cutting tool.
• Unscrew the nozzle attached to the gear shaft. To do this, the shaft must be secured by aligning the holes on the washer and on the axle, and inserting a metal bar or screwdriver into them.