How To Cut Gypsum Tiles

Articles

How to cut gypsum tiles for brick

An important point for many, this is how to cut such a tile. In fact, everything is simple, since it is gypsum, it dusty it simply and easily with an ordinary hacksaw, even for wood or metal. Sawed a little and broke. Nothing complicated. The edges are processed with a file or knife.

When I started making seams, at first everything went well, but then my glued tiles began to get clogged with glue and thus get dirty. I glanced through this moment, but unfortunately not immediately. The photo shows what this leads to. But I realized my mistake and corrected myself. After that, things went smoothly for me. Poem try to avoid such mistakes, and always have time to “screw up”.

But if you have white gypsum tiles for brick and you use white gypsum-based glue, then there will be nothing wrong with that. Drying, the glue becomes invisible on light gypsum tiles, thus Do not spoil its appearance, which has been repeatedly checked.

The PRICE for laying decorative tiles can be found on this page

And the last thing. Try NOT to glue the tiles at all. Because on some types of gypsum tiles, due to the peculiarities of its texture, after it dries it will be problematic to clean it. Work with clean hands. And I repeat once again that the glue can be any tile.

Getting started with tiles

Again, I will repeat the hackneyed truth that before starting work, the surface with which you plan to work must first be primed. On my loggia, I glued the tiles on extruded polystyrene foam and used a special primer for this material. In normal cases (brick, concrete, drywall), you will usually be able to use a standard deep penetration primer. Either way, when buying a primer, consult your seller. Tell him what wall you have and he will advise you on the necessary primer.

With regards to expanded polystyrene and drywall, here is a very clear example of how everything can be done. “Decorating bAL-KO on the inside with decorative tiles, mirror slopes”.

Be sure to prepare yourself a workplace, cover the floor and everything of value nearby that you can get dirty. It is not known where the flight of your imagination may lead.

The PRICE for laying decorative tiles can be found on this page

Cutting out complex elements and subsequent processing of edges

If it is necessary to bypass the outlet, switch or other protruding elements, an extra area is marked on the tile, which is easily shaved off with an ordinary chisel, and the edges are smoothed with fine-grain sandpaper. Curly cutting of the ends is performed along the contour of the texture.

Plaster tiles also drill well with standard metal or wood drills. But for a better job, it is better to use a carbide tipped tool. And you can change the size or shape of the hole using a hand router.

Gypsum tiles do not always have perfectly straight edges, which affects the quality of installation and makes it much more difficult. To quickly fit one element to another, you will need to remove a certain layer thickness. This is done with a chisel, and the place from which it was removed is carefully cleaned with sandpaper.

In the process of renovating the premises, various materials are used, of which nowadays there is a huge selection. One of them is gypsum tiles, which have a number of advantages.

  • It is fire-resistant, has NOT significant weight, has good heat and sound insulation.
  • With it, you can make an imitation of brick or natural stone. You can make an embossed wall with a textured pattern. In short, it all depends on your imagination.

The process of installing gypsum tiles is not complicated and resembles adhesive tiles. Therefore, we will NOT dwell on this, but many people have a question, but how to cut correctly and, most importantly, how to cut gypsum tiles, so as NOT to spoil it.

An ordinary hacksaw for wood with a fine tooth or for metal will do, the latter quickly dulls. You can use a plasterboard saw, it is convenient for it to trim already glued tiles. Some people use an angle grinder with a diamond disc, and even miter saws. In some cases, a tile cutter may also come in handy.

The advantages and disadvantages of each method

Each of the tools has its own characteristics. So, tckb dusty gypsum tiles with a hand saw for wood, its ends will have a low class of surface cleanliness (Roughness), and sometimes unevenness. This is due to the large blade teeth.

In terms of cut quality, it is better to use a hacksaw for metal. The edges will be smoother, so the need for post-processing is minimal. But this process takes much longer.

What makes gypsum tiles dusty if speed is important? For cutting, it is more advisable to use an angle grinder with a diamond disc. But it also has its drawback. Increased dustiness due to the processing of gypsum tiles with a power tool at high speeds.

For manual cutting methods, it is recommended to additionally use a miter box. Rectangular, usually wooden tray with special slots (straight and at an angle of 45 °) on the sides for a smoother cut.

Let’s summarize all that you must definitely pay attention to when working with gypsum tiles:

  • Not all surfaces are suitable for work
  • Be sure to prime everything
  • DO NOT mix a lot of glue (understanding will come)
  • Use a level
  • When working with a brush, keep it clean.
  • Try NOT to bundle tiles with glue

If you follow all these simple requirements, you will get a wonderful job. You can see such a wonderful example of interior decoration of bAL-KO with decorative tiles in the article “Interior decoration of bAL-KO with decorative brick-like tiles”. By the way, it describes the step-by-step work on finishing the bAL-KO (ceiling, floor, walls). I recommend to study, you will like.

How to cut gypsum tiles

In the process of finishing the surface of the walls with gypsum tiles, many are wondering how to properly dust it. This is due to the fact that the material has a plastic structure, unlike artificial stone and the like. But such a feature of gypsum polymer tiles can even be called an advantage, since it is allowed to use a tool of much lower hardness.

Dusting gypsum-based finishing materials can be:

  • A hacksaw for metal;
  • Hand saw for wood;
  • Angle grinder with diamond disc.

What makes gypsum tiles dusty?

In the process of finishing the surface of the walls with gypsum tiles, many are wondering how to properly dust it. This is due to the fact that the material has a plastic structure, unlike artificial stone and the like. But such a feature of gypsum polymer tiles can even be called an advantage, since it is allowed to use a tool of much lower hardness.

Dusting gypsum-based finishing materials can be:

  • A hacksaw for metal;
  • Hand saw for wood;
  • Angle grinder with diamond disc.

Laying plaster tiles. How to cut gypsum tiles to look like stone

Highlights of Plaster Tile Laying:

If there are corner pieces. Facing, it is better to start with them. But first, check how much they differ in height from ordinary elements. The difference in size can be up to 2-3 mm. Due to the influx, expanding towards the back of the product, the discrepancy can still be significant.

All such details can be revealed after facing an inconspicuous area up to 50 cm high. In general, the entire proposed plane must be drawn into 30.50 centimeter horizontal segments (by level). This makes it possible to stick to these lines and keep the laying horizontally. Otherwise, a skew may appear.

You can cut a gypsum decorative stone with a hacksaw with fine teeth, and fine-tune it with a grater with sandpaper. This is the only advantage of gypsum stone.

Joining a seam

Decorative artificial stone is produced with or without joining. The installation technique is determined depending on the selected model. Laying with jointing begins from the upper edge of the base, and the vertical joints are not placed one above the other, but with an offset. The seamless option starts from the bottom edge.

To seal the gypsum coating, the joints are filled with cement grout or adhesive mortar. Joining is performed one day after installation using a special ball or construction syringe. They are filled with a mass of up to half. The cavity between the tiles is completely filled with mortar to the entire depth of the masonry. As soon as the cement mixture sets, the excess is removed with a trowel. Then the seams are sanded with a stiff brush or sandpaper.

The grout color is matched to the shade of the coating or contrasting, depending on the interior design concept.

Installation of gypsum tiles is carried out on a prepared, even and dry base:

  • Remove the old finish, mortar, glue;
  • Remove dirt, dust;
  • Align if necessary;
  • Treat with a primer.

For reliable adhesion, an acrylic primer is used.

Decorative tiles are not used for cladding wooden and shrinkable bases.

Prepare the adhesive according to the manufacturer’s instructions. It is recommended to check the expiration date before use. The solution sets quickly, so it is prepared in small portions. Types of glue for artificial stone:

  • Silicone sealant. Provides high bond strength;
  • Cement adhesive. Suitable for all types of cladding;
  • Gypsum plaster. Most preferred for gypsum products, white;
  • PVA glue;
  • Mastic.

With your own hands

  • Installation work is performed at positive temperatures (from 10 degrees)
  • The glue is applied to the surface with a thin layer (5 mm) on the area for 3-5 tiles;
  • The back of the product is coated with an adhesive composition;
  • Presses the element to the base, adjust its position;
  • To make the seams even, use spacers;
  • The first row is laid using a building level.

Read also Tile on the walls under the tree. Advantages and disadvantages, rules for laying in the interior, examples of design with photos

Preparation of materials

Installation of gypsum tiles does not require special preparation of the base. It is enough to follow the basic principles:

  • The surface should be flat, without irregularities and undulating bends;
  • The base under the tiles must be cleaned and degreased;
  • If the surface has pronounced absorbent properties or is porous, it must be pre-primed.

The adhesive for installation must be prepared according to the instructions for use indicated on its packaging by the manufacturer. It is important that the adhesive solution, when applied to a wall or other surface of the adhesive solution, must be ensured that it fills all microcracks. However, a large amount of adhesive can create a “grout”. It is best to use a notched trowel to apply the mortar.

Pay attention to the amount of prepared glue. Do NOT knead it too much, as you may not have time to use it before the end of its suitability. It should be borne in mind that facing corners Takes a little longer than when working on a wall.

Laying gypsum tiles

Cutting out complex elements and subsequent processing of edges

If it is necessary to bypass the outlet, switch or other protruding elements, an extra area is marked on the tile, which is easily shaved off with an ordinary chisel, and the edges are smoothed with fine-grain sandpaper. Curly cutting of the ends is performed along the contour of the texture.

Plaster tiles also drill well with standard metal or wood drills. But for a better job, it is better to use a carbide tipped tool. And you can change the size or shape of the hole using a hand router.

Gypsum tiles do not always have perfectly straight edges, which affects the quality of installation and makes it much more difficult. To quickly fit one element to another, you will need to remove a certain layer thickness. This is done with a chisel, and the place from which it was removed is carefully cleaned with sandpaper.

Joining seams

The presence of seams helps to prevent dust and dirt from getting into the gaps between the elements, to ensure sealing. The jointing is carried out using a special ball or syringe pistol. A special cement-based solution is used as a grout material. This allows you to simulate the laying of natural stone.

When joining, fill the syringe with a solution and slowly squeeze it out in the direction of the seam. After the mortar has set somewhat, press it down with a spatula.

It is recommended to fill the joints completely 5 mm from the back of the tile.

You can remove excess mortar after 40-45 minutes, when the grout hardens a little. You can use a wooden or special metal trowel for this.

What makes gypsum tiles dusty?

Home 01 foundation 02 floor 03 walls 04 windows 05 ceiling 06 roof 07 systems 08 materials 09 baths 10 tools 11 decoration 12 garage 13 cottage 14 law 15 dictionary 16 question / answer 17 photos 18

In the process of finishing the surface of the walls with gypsum tiles, many are wondering how to properly dust it. This is due to the fact that the material has a plastic structure, unlike artificial stone and the like. But such a feature of gypsum polymer tiles can even be called an advantage, since it is allowed to use a tool of much lower hardness.

Dusting gypsum-based finishing materials can be:

  • A hacksaw for metal;
  • Hand saw for wood;
  • Angle grinder with diamond disc.

Preparation of materials

Installation of gypsum tiles does not require special preparation of the base. It is enough to follow the basic principles:

  • The surface should be flat, without irregularities and undulating bends;
  • The base under the tiles must be cleaned and degreased;
  • If the surface has pronounced absorbent properties or is porous, it must be pre-primed.

The adhesive for installation must be prepared according to the instructions for use indicated on its packaging by the manufacturer. It is important that the adhesive solution, when applied to a wall or other surface of the adhesive solution, must be ensured that it fills all microcracks. However, a large amount of adhesive can create a “grout”. It is best to use a notched trowel to apply the mortar.

Pay attention to the amount of prepared glue. Do NOT knead it too much, as you may not have time to use it before the end of its suitability. It should be borne in mind that facing corners Takes a little longer than when working on a wall.

Directions for use

Before laying gypsum tiles, you must familiarize yourself with a number of fundamental features of the material.

It is good because it is applicable to almost any surface. It can be glued to any surface, and not amenable to deformation under the external influence of temperatures and humidity levels: tiles, concrete and others.

  • The material is not suitable for installation on materials that deform under the influence of the external environment: wood, chipboard, plywood, fiberboard and so on;
  • Floor gypsum base is NOT moisture resistant, and then its use is not permissible in rooms with high humidity levels (above 75%);
  • Do not allow glue to get on the front side. over, it should not be allowed to dry, because This will harm the appearance;
  • The jointing of the seam requires special attention. The solution should NOT come into contact with the front side;
  • It is necessary to observe the temperature regime when laying. The air of the room and the base for installation Must have a temperature in the range from 10 to 40 degrees;
  • The jointing of the seam cannot be carried out earlier than a day after laying.

For the installation of gypsum tiles, you can use:

  • Silicone based sealant;
  • Cement tile adhesive;
  • It is also possible to lay tiles on gypsum plaster.

What can not be cut gypsum tiles

In the process of renovating the premises, various materials are used, of which nowadays there is a huge selection. One of them is gypsum tiles, which have a number of advantages.

  • It is fire-resistant, has NOT significant weight, has good heat and sound insulation.
  • With it, you can make an imitation of brick or natural stone. You can make an embossed wall with a textured pattern. In short, it all depends on your imagination.

The process of installing gypsum tiles is not complicated and resembles adhesive tiles. Therefore, we will NOT dwell on this, but many people have a question, but how to cut correctly and, most importantly, how to cut gypsum tiles, so as NOT to spoil it.

An ordinary hacksaw for wood with a fine tooth or for metal will do, the latter quickly dulls. You can use a plasterboard saw, it is convenient for it to trim already glued tiles. Some people use an angle grinder with a diamond disc, and even miter saws. In some cases, a tile cutter may also come in handy.

  • A hacksaw for wood with a fine tooth. Cuts tiles very well. It is better to use a miter box for greater accuracy.
  • Hacksaw for metal. Also works, but wears out quickly. Dust longer, more effort.
  • Saw on drywall. Cuts well plus can be used for pruning in tight spaces.
  • Angle grinder or as it is correctly called an angle grinder. Cuts quickly, but a lot of dust. It is not recommended to use in closed rooms.
  • Cross-cut machine. Precision and fast cutting, but as with an angle grinder, a lot of dust.
  • Tile cutter. In SEPARATE cases, you can use.
How To Cut Gypsum Tiles

Now, to summarize, from all of the above, we can conclude that it is not difficult to cut the plaster tile. Almost any of the listed tools is suitable for this, but let’s not forget about safety and production culture. Therefore, the angle grinder and the miter saw should still be excluded from the list.

Of course, the power tool greatly facilitates and speeds up the process of any work, but in our case it is still better to give preference to a manual one, and not to use an angle grinder and miter dust due to the large abundance of dust. By doing this, you will save yourself health and save time spent on cleaning the premises after finishing work.

How to cut ceramic tiles? Tools and technique

When choosing how to cut ceramic tiles, you need to decide on the upcoming volume of work and its type. A tool that can handle wall tiles easily will NOT work with floor tiles. Radial spray requires tools other than simple cutting.

Shaped tile cutting

During repairs, it may be necessary to make holes in the tiles for pipes, hoods or sockets. It may also be necessary to trim tiles to fit around a toilet, sink with leg, or door trims. Below we will consider how to cut ceramic tiles in THESE cases.

Ballerina

Deciding how to cut a ceramic tile to get a hole of a certain diameter? Choose a Ballerina Circular Drill for this job. The distance to the cutter is manually adjustable, and you can set any diameter that you need.

To get a neat hole, use a special drill stand while working. With the help of one ballerina, you can make up to 20 holes in the tile.

How to cut floor tiles

Ceramic flooring has a high hardness factor and places higher demands on the tool. When choosing the best way to cut ceramic floor tiles, stop at one of the options below.

How to cut tiles for wall cladding?

Ceramic tiles, which are usually used for wall decoration, are relatively soft. Therefore, cutting it, in comparison with other types of this finishing material (floor or facing tiles), does not present any particular difficulty.

Angle Grinder

The main advantage of this method is that cutting ceramic tiles with an angle grinder does not require special skills and is available to non-professionals. The principle of operation is very simple: connect to the network, press the start button and, after the disc picks up the required speed, we cut “from ourselves” according to the previously applied markings.

It is advisable to spray ceramic tiles with a tool in which it is possible to adjust the speed. It is recommended to work at a speed NOT higher than 3.5 thousand rpm. At a higher speed, ceramics begin to crack, and incandescent shavings and dust fly in all directions at great speed.

Angle Grinder. An inexpensive and easy-to-use tool. But it has several significant disadvantages. First, when cutting, a huge amount of dust and debris is generated. Secondly. The edges of the tiles are not very neat. They have to be processed additionally: to remove the jagged edges with pliers, to process the cut with a file and sandpaper.

Also, despite its simplicity, this tool must be handled with care. In order not to harm yourself while working, you need to know how to cut ceramic tiles correctly. Always hold the tool firmly in your hands so that there is a clear space in front of the blade. Be sure to use safety goggles, gloves and a respirator.