How to Cut Laminate Without Chips • CIMFLOK.COM

The choice of flooring is largely determined by quality and price. In this regard, the most acceptable ratio is the laminate. The material owes its popularity not only to practicality, but also to ease of installation. With a tool, everyone can install flooring. Accordingly, the question arises. how to saw the laminate?

Tool Requirements

For laying flooring, the material must be taken 10-15% more than the area of the room. The panels will need not only to be joined, but also trimmed. To adjust the size, use a hand or electric tool. When used at home, it should:

have a compact size;
light weight;
be convenient to use;
produce a smooth cut without chips.

The last characteristic when choosing a method for many repair lovers is the key. But its importance is somewhat exaggerated. The presence of chips up to 5 millimeters will hide the baseboard.

Both specialists and home craftsmen use for cutting laminate:

Hacksaw

Since the material consists of sawdust, it is easily sawn by hand. Use hacksaws for wood or metal. It is important that the hacksaw has small, sharp teeth. This will allow you to cut the panel without chips and bullying. With minor damage to the edges of the ends, the baseboard will close.

Before cutting, the laminate should be marked. Before sawing the laminate, the required length is measured on the panel and a cut line is applied. To get a better edge, file the bottom layer backwards.

Electric jigsaw

Everyone determines what to saw the laminate based on the availability of tools. But, if there are no devices, the most practical will be the purchase of a jigsaw. It will allow you to cut panels in all directions, including various shapes. A jigsaw is lighter than a circular saw, less dimensional than a cutter, more convenient and faster than a hacksaw. Everyone is able to master a jigsaw, since it does not require special skills.

For a quality cut, it is necessary that the jigsaw file has the opposite direction of the teeth. Usually a blade for cutting a laminate is included. To avoid defects, marking is applied on the back of the panel. It is better to cut the protective film with a clerical knife. The board is fixed face down and sawed off.

How to saw a laminate with a fretsaw without chips:

An electric jigsaw will cut the laminate with a minimum amount of dust. The jigsaw has a special bag-container for collecting sawdust. For curly threads, narrower webs should be used. A masking tape glued before sawing on the front of the panel will reliably relieve chips.

Professional cutter

The tool works without noise and dust. The device allows you to cut the laminate efficiently and quickly. The principle of operation of the torch is similar to the action of the guillotine.

How to cut chipboard without chips

The blade of the knife is lowered onto the panel with the handle, cutting off the excess with one movement. The slice is perfectly flat.

Using a torch does not require effort and skills, which allows you to lay large areas of flooring. The cutter is especially in demand among professional repair teams and perfectionists. The disadvantages of the device are the high cost and limitation of cutting, because you can only cut across the panel.

A circular saw

Despite the fact that the laminate is well sawed by hand, the use of a power tool greatly simplifies the task. Sometimes for these purposes a hand-held circular saw is used. Like a hacksaw, here, use canvases with small teeth. Before sawing the laminate, marking is applied on its reverse side, since the movement of the disk occurs from the bottom up. The board is securely fixed on a workbench or table, leaving the trimmed part on the weight. Then, along the marking line, an unnecessary piece is smoothly sawed off.

When using the angle grinder, the laminate is placed face up, since the movement of the teeth occurs from top to bottom. This will eliminate the appearance of cracks and chips. Which side to saw the laminate determines the direction of movement of the teeth. Among the disadvantages of cutting with a circular saw are:

the formation of dust and noise;
the smell of burnt wood;
the presence of skill.

When using any tool for cutting laminate, it is important to correctly calculate the applied forces.

Excessive pressure is fraught with the formation of cracks or chips on the surface of the panel. Proper calculation of the required amount of material will allow the cutting of the laminate with minimal waste.

How to properly saw the laminate, see the video:

Boards and timber are one of the main building materials. But not everyone has the financial ability to buy finished boards. In such situations, one way out is to independently engage in the harvesting of wood in a plot taken in forestry.

The advantage of a chainsaw as a tool for sawing logs

It is possible to saw a log using a sawmill, a gasoline or saw, and additional devices. When choosing one of these tools, the amount of work ahead should be considered. The cost of the cheapest stationary sawmill along with all components is 150 thousand rubles. A chainsaw is much cheaper. It is more convenient than a saw for the following reasons:

Electricity is not required to bring the tool into action. this makes it possible to use a chainsaw in the plots.
It is more powerful than an electric saw.
It starts smoothly and allows you to conveniently adjust the speed, which reduces the likelihood of an open circuit.
The inertia brake is faster than the saw.
Long working time without a break. up to one hour.
It can be used in wet conditions.

Types of working nozzles

When sawing logs with a chainsaw, various nozzles are used.

Nozzle for longitudinal sawing. It is used for sawing logs along, the process takes place in a horizontal position. After work, the master receives the same thickness of the product. Finished materials undergo a drying process, after which the boards are used in construction.

Than sawing a laminate

In appearance, the device is a small frame; it is attached to the tire on each side.

Drum debarker (binder). With the help of such a nozzle, it is easy to dissolve the log, it works due to V-belt transmission. Attached to belts on both sides, special pulleys are used for this. The speed of rotation of the shaft depends on the size of the pulleys, so the performance of the nozzle is easy to change. This technology forces the wizard to closely monitor each stage of the process, some experts use an assistant during this cut. But this option requires increased security measures.
Sawing with a lightweight nozzle. The method does not differ in high performance, but is used quite often. The element is mounted on one side, but the workpieces are slightly uneven. Such materials are necessary for the construction of sheds or fences.

Features of sawing with a homemade tool

It is possible to cut a log into boards without difficulty with the help of an independently made tool. It’s easy to make. To do this, follow these steps:

As a support, you need to use a frame from the school desk or a pipe with a cross-section in the form of a square, its optimal size is 20×20, more is allowed.
It is necessary to build two clamps, on one end to mount the crossbar with two holes for the coupling bolts, in the middle make a ledge for the tire.
For longitudinal sawing of logs into boards, you need to make a support frame, its width should be less than the length of seven to eight centimeters.
Then, two parts ten centimeters long are welded to both sides, holes are made for bolts, a handle is attached in the middle for easy operation.
Then you need to insert the clips into the grooves, install the tire, carefully fix everything.

It is not difficult to work with a home-made tool, for this you will need goats, they will serve as a support. In addition, you need to prepare a metal rail or board for use as a guide element. A log is stacked from below, the required height for work is set.

The procedure for the preparatory work

To saw the log along, you need to perform the following sequence of actions:

Take two straight boards and attach one to the other at a right angle. The result is a solid ruler.
To maintain the manufactured line, you need to make stops from the boards.
Moving trunks must be done using a tilter.
The log should be placed on a comfortable base.
On the tire chainsaw using nuts you need to fix the frame.
The supports of the leading ruler must be attached to the ends of the logs, checking the horizontal position with a level.
To fix all the brackets and structural elements, it is necessary to use self-tapping screws. Nails for these purposes are not suitable, since it is difficult to remove them in the future without causing damage to structural parts.
The leading ruler must be attached to the supports using brackets and adjust its height, taking into account the fact that the cut will not go along it, but about one centimeter higher.
The log must be rotated and the second board secured so that it rests on the ground and supports the log.

The order of the main work

Now you need to start the chainsaw and make the first cut.
Next, you need to free the log from the stops and boards and attach the leading ruler on the cut surface of the log in the direction of the next cut. The line is fastened directly to the surface or to the ends of the log with the help of supports. The second cut is done perpendicular to the first cut.
The log needs to be turned and fixed with a board against the ground.
A lead ruler is not required for further action. The guide is one of the cropped sides.
It is necessary to adjust the thickness of the cut on the frame and saw off the log on the other side so that a beam with the bark remaining on only one side is obtained.
This beam needs to be turned over and fixed so that the fixing point of the fixing board is as low as possible.
Then you need to adjust the frame to the required thickness of the board and saw the timber into boards.

Work safety rules

Do not use a circular saw without a protective cover.
Headphones, gloves, glasses, tight clothing, and a respirator must be worn.
Do not pour fuel into the hot tank of the tool, you need to wait until it cools down.
Children must not be allowed at the work site.
It is necessary to start the tool on the ground with the chain brake applied, which must be released only before cutting starts.
You must always have a first aid kit on hand.
When working, you need to hold the chainsaw by the handle of the arc, moving it forward along the guide. You should not put much pressure on the chainsaw. it should move freely.
Right-handed people should place the log on their right side, left-handers. on the left.

Instagram

Tool Requirements

have a compact size;
light weight;
be convenient to use;
produce a smooth cut without chips.

The last characteristic when choosing a method for many repair lovers is the key. But its importance is somewhat exaggerated. The presence of chips up to 5 millimeters will hide the baseboard.

Both specialists and home craftsmen use for cutting laminate:

Hacksaw

Before cutting, the laminate should be marked.

How to saw a laminate?

Before sawing the laminate, the required length is measured on the panel and a cut line is applied. To get a better edge, file the bottom layer backwards.

Electric jigsaw

How to saw a laminate with a fretsaw without chips:

Professional cutter

The tool works without noise and dust. The device allows you to cut the laminate efficiently and quickly. The principle of operation of the torch is similar to the action of the guillotine. The blade of the knife is lowered onto the panel with the handle, cutting off the excess with one movement. The slice is perfectly flat.

Video: How to Cut Laminate Without Chips

A circular saw

the formation of dust and noise;
the smell of burnt wood;
the presence of skill.

When using any tool for cutting laminate, it is important to correctly calculate the applied forces. Excessive pressure is fraught with the formation of cracks or chips on the surface of the panel. Proper calculation of the required amount of material will allow the cutting of the laminate with minimal waste.

How to properly saw the laminate, see the video:

About tool selection
Knife
Hacksaw
Jigsaw
A circular saw
What does a professional use?

Laminate. flooring, which is increasingly found in every home. Its installation always requires adjustment in length and width, because the lamellas should be laid in compliance with the brickwork rule. Accordingly, the question arises from here: "How to cut a laminate at home?".

What you need to know about a jigsaw and a file for high-quality cutting of a laminate

In this article, you will learn about different tools and how to fit using them.

About tool selection

Laminate cutting must be performed with high quality so that the cut line is straight and even, and the edge remains intact. All these points are quite easy to perform, choosing the right tool for cutting laminate. An example of the right choice is the fact that not every person can cope with a professional tool, so he should use simpler tools with which he will do this job more accurately.

The simplest tool that absolutely everyone has, but it is not the best solution. A knife for a laminate is suitable only if you want to make a small cutout for a ledge in the wall. If it is still possible to cut the lamella across, it is almost impossible to do it along, because you will spend a lot of time and effort, and the cut will turn out to be of poor quality and curved.

If you decide to use a knife, then check its sharpness, because with a blunt foot you will do much more work shortcomings than sharp.

Hacksaw

Hacksaw is very convenient to perform small trimming due to the fact that:

Laminate is easy to cut;
The fine tooth of the hacksaw ensures no chips;
If you still damage the edge, then you can easily close the flaws with a skirting board.

Sawing should be carried out according to the following instructions:

First, make a clear marking on the lamella, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
To get a good edge, cut the sheet by turning it face up.
Do not apply excessive force to the tool so as not to damage the edge being dipped.

Jigsaw

This is a more expensive tool, but its choice is the best answer to the question of what is better to saw the laminate. A jigsaw is worth buying only if the amount of work is too large to cut everything manually or if you don’t have money to purchase it.

How to cut a laminate with a jigsaw:

Install the blade with the reverse fine tooth into the jigsaw. If the canvas comes complete with an expensive and high-quality tool, then you can use it, otherwise purchase it separately.
Draw a lamella.
In this case, the lamellas need to be sawed, laid face down and fixed on a hard surface.

Another advantage of the jigsaw is that it can be sawed not only in a straight line.

A circular saw

A circular machine is not something you can cut a laminate at any time, however, if you are a happy owner of such equipment, then feel free to start sawing:

Slide the small tooth disc onto the shaft.
Draw a cut line on the slats.
If the cut is carried out along the bar, then set the width on the machine.
Saw the lamella, pushing in front of you.

The main advantage of a circular saw is the speed of its operation, which allows you to cut the lamella along in a matter of seconds, however, due to the size that you can notice in the photo, it is rarely used, in addition, you can not cut certain pieces of laminate on it, for example, under a column or ledge in the wall.

What does a professional use?

In any business, an amateur can be easily distinguished from a professional, not only looking at the speed and quality of work, but also the tool used. This happens with the laying of the laminate. Professionals use a cutter for a laminate, with the help of which they cut in a very short period of time.

As you can see in the photo, this cutter is a manual machine equipped with a sharp blade that is fixed to the base. The blade is easily adjustable for different types of cuts. Using the machine, you can cut the lamellas along, across and at different angles, without spending much effort and electricity.

The principle of work with the machine:

The lamella is placed on a machine support in a horizontal position.
The torch adjusts to the marking.
The builder applies force to the handle and the blade gradually cuts the lamella.

A professional machine is what it is very easy to saw a laminate without chipping, so everyone who works with laying a laminate tries to purchase it.

You can use any of the presented tools, however, remember that the most important thing in sawing a laminate is the quality of the edge. Remember the tip: to make as few chips and bumps as possible, do not apply much effort to the sawing tool, because this will make the tool pull out fragments from the body of the material, and not cut them out.

Now you know all the ways of sawing, so you can decide on your own the question of how to saw through the laminate.

About tool selection
Knife
Hacksaw
Jigsaw
A circular saw
What does a professional use?

About tool selection

If you decide to use a knife, then check its sharpness, because with a blunt foot you will do much more work shortcomings than sharp.

How and with what to saw a laminate. the choice of tools and the nuances of sawing laminated coatings

Hacksaw

Hacksaw is very convenient to perform small trimming due to the fact that:

Laminate is easy to cut;
The fine tooth of the hacksaw ensures no chips;
If you still damage the edge, then you can easily close the flaws with a skirting board.

Sawing should be carried out according to the following instructions:

First, make a clear marking on the lamella, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
To get a good edge, cut the sheet by turning it face up.
Do not apply excessive force to the tool so as not to damage the edge being dipped.

Jigsaw

How to cut a laminate with a jigsaw:

Install the blade with the reverse fine tooth into the jigsaw. If the canvas comes complete with an expensive and high-quality tool, then you can use it, otherwise purchase it separately.
Draw a lamella.
In this case, the lamellas need to be sawed, laid face down and fixed on a hard surface.

Another advantage of the jigsaw is that it can be sawed not only in a straight line.

A circular saw

A circular machine is not something you can cut a laminate at any time, however, if you are a happy owner of such equipment, then feel free to start sawing:

Slide the small tooth disc onto the shaft.
Draw a cut line on the slats.
If the cut is carried out along the bar, then set the width on the machine.
Saw the lamella, pushing in front of you.

What does a professional use?

The principle of work with the machine:

The lamella is placed on a machine support in a horizontal position.
The torch adjusts to the marking.
The builder applies force to the handle and the blade gradually cuts the lamella.

A professional machine is what it is very easy to saw a laminate without chipping, so everyone who works with laying a laminate tries to purchase it.

Now you know all the ways of sawing, so you can decide on your own the question of how to saw through the laminate.

About tool selection
Knife
Hacksaw
Jigsaw
A circular saw
What does a professional use?

About tool selection

The simplest tool that absolutely everyone has, but it is not the best solution.

What is better to saw the laminate?

A knife for a laminate is suitable only if you want to make a small cutout for a ledge in the wall. If it is still possible to cut the lamella across, it is almost impossible to do it along, because you will spend a lot of time and effort, and the cut will turn out to be of poor quality and curved.

If you decide to use a knife, then check its sharpness, because with a blunt foot you will do much more work shortcomings than sharp.

Hacksaw

Hacksaw is very convenient to perform small trimming due to the fact that:

Laminate is easy to cut;
The fine tooth of the hacksaw ensures no chips;
If you still damage the edge, then you can easily close the flaws with a skirting board.

Sawing should be carried out according to the following instructions:

First, make a clear marking on the lamella, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
To get a good edge, cut the sheet by turning it face up.
Do not apply excessive force to the tool so as not to damage the edge being dipped.

Jigsaw

How to cut a laminate with a jigsaw:

Install the blade with the reverse fine tooth into the jigsaw. If the canvas comes complete with an expensive and high-quality tool, then you can use it, otherwise purchase it separately.
Draw a lamella.
In this case, the lamellas need to be sawed, laid face down and fixed on a hard surface.

Another advantage of the jigsaw is that it can be sawed not only in a straight line.

A circular saw

A circular machine is not something you can cut a laminate at any time, however, if you are a happy owner of such equipment, then feel free to start sawing:

Slide the small tooth disc onto the shaft.
Draw a cut line on the slats.
If the cut is carried out along the bar, then set the width on the machine.
Saw the lamella, pushing in front of you.

What does a professional use?

The principle of work with the machine:

The lamella is placed on a machine support in a horizontal position.
The torch adjusts to the marking.
The builder applies force to the handle and the blade gradually cuts the lamella.

A professional machine is what it is very easy to saw a laminate without chipping, so everyone who works with laying a laminate tries to purchase it.

Now you know all the ways of sawing, so you can decide on your own the question of how to saw through the laminate.

source