How to cut septal panels for window slopes. The main advantages and disadvantages

How to cut a sandwich panel. experienced builders give advice

panels, how much respectively of their installation of the technological process. This affects their service life, and the energy efficiency of the structure in the end.

Avoid errors and misses

Many errors during the installation of sandwich panels are associated with an inattentive, cursory reading of the design and installation documentation that often contains comprehensive information about the panels and connecting elements.

But a clear adherence to the annotation is not able to insure from some errors in the installation process, speaking specifically:

• Iron sandwich panels are without damage and traces of corrosion. In the same state, a metal frame is also obliged, which will be mounted;
• If the panels are attached to the wooden frame, it is impregnated with antiseptics and insecticides;
• Dirty sandwich panels cannot be cleaned with detergents containing alkalis, acids and abrasives;
• The protective film should not be under the influence of direct sunlight. It should also be protected from solvents;
• The protective film must be removed from the sandwich panels no later than a week and a half after installation, but this cannot be done in very hot and very cool weather;
• You can not walk on sandwich panels, lay different objects on their surface and strengthen something here.

How to raise and install panels correctly?

Transport package with sandwich panels (read about the technical properties of these products here) is raised to the installation height with special equipment-vacuum lifts.

Opposite such purposes, an ordinary lifting crane is used, you need to take a number of measures to prevent damage to the panels:

• Soft slings are used to raise the transport package. With all this, the capture of the slings is actually not allowed. The castle parts of the panels are protected from the probable damage by slings with bars-springs, a length of two or more than 122 cm, moderately located above and under the package;
• Specifically you can’t raise a sandwich panel with a sandwich panel.

Also, in the course of work, subsequent rules should be followed:

• The panels must be attached strictly at an angle of 180 degrees, t.e. vertically. Docking from a different angle can lead to locks of locks;
• The produced should be extremely careful for avoiding damage to the protective coating. Otherwise, the service life of the panels will be significantly reduced.

Fastener “P” profile

The starting profile is cut by the size of the slopes, which resembles the letter p. It is attached with the help of self.tapping screws exactly along the edge of the window profile. The distance between the screws is approximately 10-15 cm. In this case, first of all, the profile should be installed at the top. Then the side elements are brought to the upper profile close, leaving no gaps.

Nuance: it is possible to install slopes using a sandwich panel without the use of a starting profile. In this case, strips of sandwich panels are launched close to the window profile for 1cm deep. This is done with a step.by.step nonsense to fix the slope. The process is more laborious than the use of the “P” profile, however, the result is more aesthetic.

Fasten, but in moderation

Fasteners for sandwich panels are selected taking into account the type of structure and its thickness. As a rule, self.cutting screws (self.tapping screws) are used for this.

Their length is the sum of the thickness of the panel, frame and compensation of the height of the rubber washer (5 mm). The latter is required for use with self.tapping screws. it does not allow the metal head to damage the panel when screwing and sealing the mounting location.

Proper and incorrect panels fastening

The panel of 6 m long is attached with six self.tapping screws, 4 m long and less. four, with a length of more than 6 m. eight. Self.tapping screws are attached with an electric screwdriver with a pre.corrected tightening force.

With proper tightening, the washer is not deformed and at the same time tightly pressed to the metal. Too tightly tightening the puck, insufficiently strong does not ensure the tightness of the mount. The slanting self.tapping screw is categorically unacceptable.

How to cut a sandwich panel. Cut problems

Sandwich panels are a multilayer design for surface decoration. From metal sandwich panels, you can build persistent structures, since the material is able to make a fairly high load. That is why he gained extraordinary popularity in the construction sector. It is not sacred that due to the number of layers there are certain problems.

It is better to make measurements in advance and order cutting at the factory

For starters, it is worthwhile to figure out exactly how this material works. Any type of sandwich panel consists of three layers. Two outer layers protect the inner layer of insulation from various risks. Due to the insulation, the ability to cut such panels is limited in just a few ways.

Sandwich panels cutting can be done only by several mechanical methods without the use of thermal elements. gas cutters, plasma cutters and saws, which can very much heat the working surface. And all this is because the insulation that is between the panels is very quickly ignited by open fire and has the ability to ignite at high temperatures (above 200 °). When cutting with any type of surface heating, the middle layer flashes, exuding caustic smoke. Therefore, it is completely not recommended to use any elements that can heat the surface or create open fire. Such attempts to cut metal, only destroy special protective coatings of panels.

Preparatory stage

Sandwich panels belong to practical materials that are as simple as possible in installation. Due to the inner layer, which is a sheet of compacted foam, thermal insulation of building structures is ensured and heat leaks from the room are prevented. The outer layer made of smooth polyvinyl chloride looks neat and aesthetically pleasing, resistant to aggressive environment and moisture. This material is durable, not damaged by pests and fungus.

The panels are both two.layer and three.layer, in the second case, the PVC coating is available on both sides. Such panels are suitable for installation on a wooden crate due to increased hardness, attach them to foam or liquid nails irrationally. at the surface from PVC low adhesion.

Slopes of this type are mounted in three ways:

• on liquid nails (the surface of the wall should be flat);
• on the mounting foam (small irregularities of the base are allowed);
• on the frame from the rails (if the base is difficult to align with the help of plaster composition).

We will consider in detail the first option for installing slopes, t.e. on the starting profile and liquid nails in which the minimum of space is “eaten”. Forgot to add that the thickness of the two.layer panel is about 10 mm.

At the preliminary stage, the slopes should be thoroughly cleaned, removing everything that is capable of eliminating the base and all protruding tubers. Be sure to remove the excess mounting foam around the perimeter of the window unit that remained after installation.

Then a plastered solution for black work is prepared. Cracks and hollows are locked with them. the surface of the slopes should be flat, you can check this using the level. Pay attention, if your sloping surface is even, then you do not need to plaster it and you can safely miss this step.

Wait for the complete drying of the plaster layer and process the slopes with a primer for porous bases so that the glue composition reliably fixes the sandwich panel. After the primer dries, conduct processing with an antifungal composition, having waited for its complete drying, you can proceed to the cladding of the slopes.

Paste a Valid Adsense Code in Ads Elite Plugin Options Before Activating Its.

How to cut windows for windows. Installation of corners on window slopes or doors

Having dealt with what such products are made of, what are their features and having decided on the choice, you should study how to install corners on slopes. Detailed instructions are given below.

What glue to use

In addition to the corners themselves, we will also need an adhesive with which we will attach the selected element. When choosing it, it is worth remembering that quite often, especially if it is necessary to glue a narrow product, the glue seeps from under it and, of course, falls on the walls. As a result of this, the latter can be damaged, which, accordingly, will negatively affect the appearance of the room as a whole. Therefore, you should choose such an adhesive composition, the excess of which can be removed from the surface.

Basically, the corners are glued to new slopes, but nevertheless, check that the surface is relatively flat, since no decoration will be able to hide large hillocks. It should not have foreign objects like nails, screws, etc. D. It also needs to be degreased, for this purpose, white spite.

Elimination of a crack near the window frame

How to make a crack between the frame and the slope? In some cases, if a cardinal solution to the problem does not suit or not enough funds and time, and it is necessary to update the surface, then it is necessary to perform the following:

Using the painting tape, it is necessary to seal the window frame at a distance of about 1-2 mm from the crack. If the sloping is stained after sealing the crack, then it is necessary to seal it with a masking tape. If coloring is carried out, then it is enough to glue only the frame.

In the case of a radical and complete elimination of the crack, it is necessary to unveil the gap first and see how qualitatively the cracks between the window and the wall were blended using mounting foam. In most cases, it is not enough and therefore it is necessary to clean the gap from the remnants of the old foam, and then blow it in a new way in sufficient quantities. Когда монтажная пена высохла, остатки необходимо удалить и приступать к отделке откосов.

The global solution to the problem is best done in the warm season, when the walls of the house are warm to the whole depth.

Cutting sandwich panels

Starting the installation of slopes, it is necessary to stock up on the cutting tool. The quality of the cuts and the final result of the installation of elements will depend on its characteristics. Can be used:

Important. The tool should have small cloves to prevent material crushing on the cut. Keep at a slight angle to the surface, cut only from the front side. The corner grinder needs to work very carefully, without effort, so as not to inadvertently damage the material.

How to cut metal sandwich panels. Cut problems

Sandwich panels are a multilayer design for surface decoration. From metal sandwich panels, you can build persistent structures, since the material is able to make a fairly high load. That is why he gained extraordinary popularity in the construction sector. It is not sacred that due to the number of layers there are certain problems.

It is better to make measurements in advance and order cutting at the factory

For starters, it is worthwhile to figure out exactly how this material works. Any type of sandwich panel consists of three layers. Two outer layers protect the inner layer of insulation from various risks. Due to the insulation, the ability to cut such panels is limited in just a few ways.

Sandwich panels cutting can be done only by several mechanical methods without the use of thermal elements. gas cutters, plasma cutters and saws, which can very much heat the working surface. And all this is because the insulation that is between the panels is very quickly ignited by open fire and has the ability to ignite at high temperatures (above 200 °). When cutting with any type of surface heating, the middle layer flashes, exuding caustic smoke. Therefore, it is completely not recommended to use any elements that can heat the surface or create open fire. Such attempts to cut metal, only destroy special protective coatings of panels.

Products from PVC panels

Before installing plastic slopes with your own hands, you need to familiarize yourself with the qualities of the material that is used for their manufacture. One of them can be a PVC panel.

Description of the material

Another name of this material is ceiling panels. They make them from polyvinyl chloride.

They consist of two plastic plates with stiffeners inside. For some models, the presence of locking joints on the ends is provided.

The panels can have different sizes, but when installing them will still have to be cut in accordance with the necessary sizes. Despite the fact that the panels can have a length of 3 and 6 meters, 6-meter products should be purchased. The thickness of the panels varies from 0.5 to 1.2 cm. The type of product can also be different: panels, rails or PVC sheets.

Also purchase components for plastic panels. The kit should have fasteners and plastic elements. Their description is presented in the figure below.

One of the advantages of any plastic panels is their wide color scheme. PVC color slopes can be selected for any interior.

The color of the finishing plastic can be selected for any interior

The interior decoration will look original when lining the openings of the window with plastic panels with the image or imitation of any natural and artificial material. When the windows are colored or brown, you can use painted products

It is important that in this case the window fittings are combined with them

PVC panels can imitate a wooden surface

The panels can be plain, laminated, lacquered, a printed pattern or image applied by thermal printing on its surface. Installation of plastic slopes will give the windows a neat decorative appearance. How to make plastic slopes will be told below.

Positive qualities of the material

A high.quality decoration of slopes with plastic with your own hands is due to the properties of ceiling panels.

• the material is not toxic;
• have high moisture resistance;
• They are easy to install and care;
• have insignificant weight, so they do not create a load on the base;
• Plastic is non.combustible material, but when melting it distinguishes toxic caustic smoke; Products are resistant to temperature differences;
• have frost resistance;
• create an ideal even rigidly fixed surface;
• have a modern look and are suitable for any interiors;
• The cell structure provides reliable sound insulation;
• Static electricity do not accumulate on their surface;
• Panels are resistant to household chemicals.

Mounting

How to install slopes from plastic on the windows with your own hands in stages, shown below. Before starting the finish of the slopes with panels, it is necessary to measure. The internal sides are measured twice. at the window and near the wall.

• The installation of plastic slopes on the windows begins with the fact that they remove the mounting foam, which went outside the seam along the perimeter of the window frame. To do this, use a sharp construction knife;

Before installing the slopes, excess foam is removed along the perimeter of the window frame, it will be necessary to fix the wooden block. In the manufacture of a bar, you need to perform a slope on one side of it. This is done so that you can firmly fix the bar near the window frame;

To fasten the slop, a wooden block with a slope is made ready.made bars should be installed around the perimeter of the window frame in such a way as to enter it a little. Fastening can be carried out using self.tapping screws or dowels;

The bar is fixed using screws around the perimeter of the frame of the plastic bar, which is called the start profile, is purchased in the construction store. Using a construction stapler or screws, attach it along the perimeter of the window to the wooden bar;

The starting profile is mounted to the wooden bar according to the previously obtained sizes, we make the necessary elements. Cut the plastic carefully so as not to damage;

PVC panel cuts must be done without strong pressure to install the panels, you must first on the side walls of the window opening. The panels must be put in the starting profile;

The panel is inserted into the starting profile. The part must be separated from the wall and cover the space with foam with foam. Then put it in place and press it a little so that the foam grabs;

PVC panel is fixed using mounting foam

In this way, it is necessary to finish the entire window opening;

How to cut windows for windows. Installing slopes on plastic windows with your own hands

Installing plastic slopes on the windows with your own hands

A beautiful and strong slope not only decorates the window, but also protects the room from heat loss. New building and finishing materials allow you to accelerate the process of installing slopes. In our article we will tell and show in the photo how the installation of window slopes is made, and how much it will be possible to save if you do the job with your own hands.

With the advent of polyvinyl chloride windows (PVC) and metal.plastic profile, the quality of thermal insulation has increased several times. Windows do not change their shape under the influence of low and high temperatures, do not dry out to cracks and do not jam. Durable questionnaires and installation synthetic foam provide rapid and high.quality insulation of the room from the external environment. The installation of slopes is called decorative wall decoration in the window opening, completing the process of installing the window.

Types of finishing slopes

• Plassing of window slopes is considered a classic option in houses made of brick and concrete. After coating with a high.quality plaster solution in several layers, the surface can be painted or poured with wallpaper. The laborious process takes more than one day of work of professional plastering. While one layer dries, 5. 6 hours will pass. Disadvantages of plaster are opened over time. Due to the temperature differences at the contact site of the window and solution of the window and the solution, a crack appears, which must be filled with sealant so that there is no draft. A professionally made slope will last for decades, but only the master will make it for the corresponding fee.
• Spear from drywall is much easier to mount, but this material is characterized by a significant drawback: it damps at the slightest humidity. In the offseason, during the rain, the slope risks covering up cracks and crumpled when swelling. Although the use of moisture.proof KNAUF.liners will solve this problem. The method of attaching sheets on the walls does not differ from more modern plastic slopes, but to seal adjustments to the window body and to the total surface of the wall, the builder will have to show ingenuity due to the absence of typical corners-wraps.
• Plastic slopes appeared with the technology of plastic windows. Pvc is made from the panels to cover any surface. Environmental plastic does not emit harmful substances, does not burn, does not absorb moisture and is easily washed with water with household chemicals. Can have any plasticity depending on fillers. Plastic slopes on windows are made lightly, according to cellular technology. Plastic is perfectly painted, so on sale there are a huge number of options for coloring and imitations for different materials. Called panels are available.

Products from PVC panels

Before installing plastic slopes with your own hands, you need to familiarize yourself with the qualities of the material that is used for their manufacture. One of them can be a PVC panel.

Description of the material

Another name of this material is ceiling panels. They make them from polyvinyl chloride.

They consist of two plastic plates with stiffeners inside. For some models, the presence of locking joints on the ends is provided.

The panels can have different sizes, but when installing them will still have to be cut in accordance with the necessary sizes. Despite the fact that the panels can have a length of 3 and 6 meters, 6-meter products should be purchased. The thickness of the panels varies from 0.5 to 1.2 cm. The type of product can also be different: panels, rails or PVC sheets.

Also purchase components for plastic panels. The kit should have fasteners and plastic elements. Their description is presented in the figure below.

One of the advantages of any plastic panels is their wide color scheme. PVC color slopes can be selected for any interior.

The color of the finishing plastic can be selected for any interior

The interior decoration will look original when lining the openings of the window with plastic panels with the image or imitation of any natural and artificial material. When the windows are colored or brown, you can use painted products. It is important that in this case the window fittings are combined with them.

PVC panels can imitate a wooden surface

The panels can be plain, laminated, lacquered, a printed pattern or image applied by thermal printing on its surface. Installation of plastic slopes will give the windows a neat decorative appearance. How to make plastic slopes will be told below.

Positive qualities of the material

A high.quality decoration of slopes with plastic with your own hands is due to the properties of ceiling panels.

• the material is not toxic;
• have high moisture resistance;
• They are easy to install and care;
• have insignificant weight, so they do not create a load on the base;
• Plastic is non.combustible material, but when melting it distinguishes toxic caustic smoke; Products are resistant to temperature differences;
• have frost resistance;
• create an ideal even rigidly fixed surface;
• have a modern look and are suitable for any interiors;
• The cell structure provides reliable sound insulation;
• Static electricity do not accumulate on their surface;
• Panels are resistant to household chemicals.

Mounting

How to install slopes from plastic on the windows with your own hands in stages, shown below. Before starting the finish of the slopes with panels, it is necessary to measure. The internal sides are measured twice. at the window and near the wall.

The installation of plastic slopes on the windows begins with the fact that they remove the mounting foam, which went outside the seam along the perimeter of the window frame. To do this, use a sharp construction knife;

Before installing the slopes, excess foam is removed along the perimeter of the window frame, it will be necessary to fix the wooden block. In the manufacture of a bar, you need to perform a slope on one side of it. This is done so that you can firmly fix the bar near the window frame;

To fasten the slop, a wooden block with a slope is made ready.made bars should be installed around the perimeter of the window frame in such a way as to enter it a little. Fastening can be carried out using self.tapping screws or dowels;

The bar is fixed using screws around the perimeter of the frame of the plastic bar, which is called the start profile, is purchased in the construction store. Using a construction stapler or screws, attach it along the perimeter of the window to the wooden bar;

The starting profile is mounted to the wooden bar according to the previously obtained sizes, we make the necessary elements. Cut the plastic carefully so as not to damage;

PVC panel cuts must be done without strong pressure to install the panels, you must first on the side walls of the window opening. The panels must be put in the starting profile;

The panel is inserted into the starting profile. The part must be separated from the wall and cover the space with foam with foam. Then put it in place and press it a little so that the foam grabs;

By installing slopes on plastic windows, at their corners you can fix the platbands. How to make slopes with a platband, shows a step.by.step instruction located below.

Step.by.step installation guide

Preparatory work

To install slopes from sandwich panels, it is necessary to arm yourself with the right set of tools and materials. For work, they will come in handy:

• Sandwich Panel.
• P-profile, which is the starting.
• F-profile-the so-called device cover.
• Plastic in liquid form (preferably).
• Construction roulette.
• A sharply sharpened knife.
• Self.tapping screws 2.5 7 mm.
• Several screwdrivers with different tips, the drill can be replaced with a screwdriver.

Armed with a roulette, take measurements of the length and width of the slopes, this is the main guideline that determines the final dimensions of the sandwich panels for slopes. Taking into account these values, cut out a few lanes with a knife: one will be located in the upper part of the window, and the remaining two on the sides.

Now let’s talk about how to correctly cut the elements of a sandwich device:

• The width of the elements is laid 10 mm larger than the primary measurements of the window, this will provide a more dense contact with the frame.
• Around the window box, a hole should be cut right in the frozen foam, the depth of which is 100 mm and a width of 1 mm.
• At the edge where the sandwich panel will be located, measure 10 mm and draw a fishing line for a trimmer. Cut the material strictly along the line, but capture exclusively the upper and insulation levels. How to cut a sandwich punch for slopes? A special tool for this will not be needed, you can do with an ordinary kitchen knife.
• Cut off the end, remove the extra layers.

If the finish of the slopes of the sandwich panels is planned in one place, you can try to save and buy ready-made, chopped strips without purchasing a whole panel.

The main part of the work

After the preparation of the necessary tools and materials, we move to the main part of the sloping installation process. First set the frame:

• We carefully process the window box. we get rid of excess mounting foam, pass through the design with a cloth to clean it of dust and garbage.
• We distribute vapor barrier material over the entire area of ​​the slopes. If you want to insulate the openings even more, use the stripes of the foam.
• With a brush, aerosol or directly from the tube (depending on the packaging), apply an antiseptic agent that will protect the window from the appearance of mold, the reproduction of fungi and other harmful substances to coating in the future.
• Focusing on the inner part of the device, following the perimeter, install the crate made of wood. The dimensions of the rack material are 2040 mm. The rail is fixed by the dowel-bvs. Observe the distance that should reach 40 mm. In the sections of the joints where the side and upper rails of the crate are coat, lay a gap of 10 mm or more-it will be needed to install PVC elements for slopes at the top. If the frame cannot be fixed, lining with sandwich panels is fixed using foam.

External stripes are located

Installation of panels is always carried out from the upper part of the window box, moving to the lower. Place the protruding element in the formed groove so that the part is tightly adjacent to the window. Fill free space with material, which will ensure the maintenance of the temperature and isolate the window structure from drafts, for this it is better to apply the isover.

The external side is fixed due to self.tapping screws, roll with the correct position of the upper decoration using the construction level. The finish of the lateral slopes is a decoration with a special edge.

Hi all! After installing plastic windows, it is necessary to take care of the high.quality decoration of the slopes so that they look aesthetically pleasing, not covered with mold, are easy to install and did not freeze in the cold. Roads from sandwich panels have all of the above qualities. As mentioned above, they do not be difficult to install them with your own hands, which you can make sure below.

To finish the slopes using the sandwich panel, you need to prepare the following:

• Roulette, level, pencil and sharp mounting knife or corner grinder;
• plastic P. figurative and edging profile, liquid nails construction gun for tube;
• Rule and knock;
• electric screwdriver and screws;
• liquid plastic or white sealant, a primer for concrete bases brush and an antifungal agent;
• plaster mixture a spatula (if the slopes are uneven), a construction grater or a bar with sandpaper of medium grain, a construction mixer and a drill.

Is it possible to cut sandwich panels? How to do it right

Metal sandwich panels-extremely convenient material for decorating structures of any size and purpose. They embodied the excellent strength properties: durability, resistance to corrosion, good bearing capacity. And complemented them with excellent thermal insulation characteristics and ease of installation. Almost the only problem that can arise during construction is the need to cut the panel for “non.standard” size or shape.

What is the difficulty?

The sandwich panels consist of several layers: external (in most cases-metal), which provide strength and internal, which is responsible for insulation. It is the latter that limits the capabilities of cutting. Since most heaters are easily ignited (or caustic smoke is distinguished during flowering), use fire and other cutting methods that heat the surface to temperatures above 200 degrees is strictly prohibited. The heating is also undesirable for the polymer coating of the outer layers: when heated, it loses integrity.

Obviously, due to constructive restrictions for cutting, only simple mechanical methods remain.

Sheets with an outer layer of polymers (plastisol, polydictoriona, polyester, pool) are recommended to be cut with an electrician, corner grinder or a construction knife. Operations begin with preliminary marking and cutting of the outer layers. The internal is cut off last. Synthetic surfaces are very durable and therefore their cutting is a fairly troublesome thing.

OSP or drywall are easier to cut. A strip or disk saw is best suited here. They can also cut metal coatings. An even better option for metal is a press gill. Its mechanism will make an incision quickly and exactly vertically.

Correct slicing sandwiches and the choice of tools

But with all its undeniable advantages, sandwich panels have one serious drawback: they are extremely demanding on mechanical processing. Plastic sheets are very fragile and is easy to damage them in any careless movement. Foamed polystyrene is a fairly viscous material that requires a lot of effort during its mechanical processing.

And the surface of the window slopes is such that the sheets of sandwich panels should be cut to give them the necessary sizes. To do this, it is best to use an electric jigsaw, ultra.suffering movements of its cutting blades create an uniform force under which fragile plastic and viscous polystyrene are carefully cut. Another advantage of an electric jigsaw is an opportunity to create curved cuts.

The only drawback of this tool is that not every owner is found.

Unlike the same corner grinder, which is necessarily found if not with you, then your symbolic or neighbors for sure. But there is one difficulty. During cutting, the corner grinder should be kept by weight. Since this tool has a fairly large weight, it itself, even with a not very strong press, can damage fragile plastic.

Finally, for cutting, you can use a hacksaw for metal, but with this method the likelihood of cracks and chips due to the emerging resonating vibrations increases significantly, and as a result you will get uneven edges of the cut.

Therefore, if you do not have an electric jigsaw or corner grinder at home, then it is best to entrust this procedure to a professional who has the necessary power tool in the presence. Or you can take the instrument for rent, but in the current conditions it will cost you dearly.

For window openings, two- and three-layer sandwich panels are used. The former are made of decorative plastic, to the reverse side of which on an adhesive base is fixed a thermal insulation layer of foamed polystyrene. In the second, decorative plastic closes the thermal insulation layer on both sides. As a result, three-layer sandwich panels are greater, which is why they preserve their shape better.

Note that decorative plastics are made in any color scheme, as well as in imitation of various textures of facing materials (wood, stone, etc.P.). The foamed polystyrene has almost zero thermal conductivity, which is why condensation will not form on the walls of the window opening, and the windows will not fog.

How to install a sandwich panel on a plastic door

Increasingly, the owners of the houses opt for plastic doors, therefore, slopes for them should also choose the right type and type of material. Modern sandwich panels are perfect for this. You can install them yourself, using detailed instructions and owning the skills of repair or construction.

The process of installing sandwich panels for doors is as follows:

And as materials, accessories, the following construction products should be used:

• Buy a sandwich panel of suitable thickness in advance;
• Measuring and cutting tools (these include laser or alcohol level, roulette, acute construction knife or electrician, drill)
• Accessories for finishing measures (spatula, trowel, PVC focuses, nippers for plastic, masking tape, screws) mounting foam, plaster, primer.

Armed with everything necessary, the installation measures begin directly.

Step.by.step installation

Available price, ease of material, ease of installation and ease of operation allowed to use a sandwich panel very widely in the decoration of window openings.