How to start a Stihl 180 chainsaw • CIMFLOK.COM

We start STIHL MS 211 C-BE

The fuel supply system in the STIHL MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the STIHL chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting STIHL 180 and follows the same algorithm.

How to start the saw after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such Комментарии и мнения владельцев can be found on the forums dedicated to the repair and operation of saws. Let’s figure out how to start a chainsaw after a long period of inactivity.

The fact is that a successful start after downtime must be taken care of in advance and the saw should be properly prepared for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system.

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage.

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1. 2 ml of the fuel mixture to the cylinder. This can be done with a syringe.

Getting Started STIHL MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the STIHL 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

How to start a chainsaws with a decompression valve

Before starting a STIHL chainsaw with a decompression valve, you must turn it on. It should be noted that there is no decompression valve on the STIHL 250 saw.

After the first flash has passed, the valve will be set to normal operation, respectively, after the engine control lever is set to the open air damper position and starting continues, the decompression valve must be pressed again.

Tech Chat with Chad. How to start your STIHL chain saw. Season 1 EP 1

The valve operation is schematically shown in the figure below.

Stihl MS 180 Review and starting technique

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch, a person will have to apply significantly less effort.

A saw with a decompression valve, whether the engine is cold or hot, must be started using the valve to relieve the cranking force of the engine. This will significantly increase the service life of the starter and reduce the number of torn laces, since it is installed on chainsaws with a large cylinder volume and, accordingly, compression.

We start STIHL 180

In order to start the STIHL 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the STIHL 180 chainsaw, namely:

Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the STIHL 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched);
Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start);
Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle valve remains in the same position as before);
Pull starter and start. The saw will start and run at higher rpm due to the throttle valve being as open as possible. To set the damper to idle mode, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The STIHL MS 180 chainsaw, as standard, is not equipped with any additional devices that can facilitate starting.

Below you can see how to start STIHL 180. The video reflects in detail all the main points, and the author’s Комментарии и мнения владельцев allow you to understand the whole process to the smallest detail.

How to start a STIHL chainsaw

All STIHL chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed, allowing you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly.

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model.

What happens at the moment of priming fuel with primer, and how it helps to start the saw more efficiently?

At the moment of starting the saw without a primer, several movements of the starter are carried out only so that the fuel pump, under the action of an impulse from the saw crankcase, pumped fuel into the carburetor.

A pump installed in the fuel line allows you to manually pump gasoline into the carburetor without unnecessary movements with the starter. The effect of this action is obvious, the saw will start much faster.

Many owners of gasoline-powered tools mistakenly believe that a hand pump can overly pump fuel into the carburetor and, for this reason, flood the candle. This is fundamentally wrong, since the system is capable of circulating around. Excess gasoline from the carburetor will be directed, through a dedicated hose, back to the tank.

There is no need to use a primer on a hot chainsaw, since there is enough fuel in the carburetor to start.

How to start the saw after long periods of inactivity

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage.

How to Start a STIHL 180 Chainsaw Correctly

How to start a STIHL chainsaw: starting process and overview

What remains to be done for our client. STIHL branded chainsaws have two-stroke engines. Their cool start is carried out using a similar method. But on the market we meet models on the pages of which there is additional equipment, when using it, of course, start the saw without making any special efforts. Therefore, the starting method may differ.

Algorithm for setting the saw “STIHL 180

If you have a question about how to start a STIHL chainsaw, then this process can be seen on the example of model 180. To be able to perform work on a cool one, you need to turn on the ignition and set the engine control lever to the lower position. With all this, the carburetor flap will block air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled a couple of times until the 1st flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the STIHL chainsaw, you need to set the control lever one position up. With all this, the air damper will open, while the throttle remains about the same position.

The starter must be pulled and started. The tool runs at high revs, the throttle valve will be open. To set the latter to idle, use the gas trigger and release it. With all this, the tool should start working normally. On the described model of the chainsaw there are no additional devices that would make it easier to start.

How to start a chainsaws with a decompression valve

Before starting a STIHL chainsaw with a decompression valve, you must turn it on. It should be noted that there is no decompression valve on the STIHL 250 saw.

The valve operation is schematically shown in the figure below.

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch, a person will have to apply significantly less effort.

We start STIHL MS 211 C-BE

The fuel supply system in the STIHL MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the STIHL chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting STIHL 180 and follows the same algorithm.

Tips for starting a saw MS 180 C

This device, in comparison with the previous one, has some differences in the trigger mechanism. But there will be no configurations in the start method. The described version of the equipment has a system that, using a spring in the saw starter, reduces the resistance of the motor.

All STIHL chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed, allowing you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly.

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model.

How to start a STIHL 180 cold

Starting a STIHL chainsaw almost always follows the same algorithm, except for those cases when a decompression valve and a fuel primer are additionally installed on the chainsaw. These gadgets are designed to facilitate the start-up process and do an excellent job of their functions.

2 diagram of a standard mechanism. how to start the saw correctly

The ignition is switched on. To do this, you need to move the toggle switch to the desired place or move the switch.
The swap primer usually has to be pressed more than twice. Gasoline is poured into it, after which you will have to press the device more than three times. Sometimes the chainsaw is not equipped with a primer, then you can skip this step.

The adjustment lever, which is responsible for the location of the damper, must be pulled out as far as it will go. Many chainsaws have the ability to block this element. Then it can only be moved while pressing and holding the throttle button. Some chainsaws do not have this lock, which makes them more comfortable to use. In these models, gas may not be fixed or retained when using automatic technologies.

You need to take the starter handle and jerk it with sharp movements until the ignition is heard. It is celebrated by the institution and the almost instantaneous shutdown of the motor. After that, the shutter must be pushed into its original position, checking it until it stops. Then the starter handle jerks again until the device starts. Before carrying out this event, you need to make sure that it is this method that will help the chainsaw start. Some devices have a different ignition system. In order for the motor to work in them, you need to move the damper only by 50%, and only when the motor starts to work fully.

If you purchased a model with a locking gas, you need to prepare in advance for the highest engine speed immediately after activating the device. When there is no fixation, the initial power is very low, so in most cases it has to be increased. If you do not take any action, then in the latter case, the saw runs for a short period of time, and then automatically stalls. If such a situation occurs, you need to start the chainsaw again.

When the device stalls constantly, you need to systematically start it up again (see what to do when the chainsaw stalls when you press the gas). After a while, the motor will pick up speed and be able to maintain active work without interruption.

Chainsaw Husqvarna 395xp

the power of the model is 6.66 liters. from;
chain size. 60 cm;
containers for lubricant and fuel. 500 ml and 900 ml, respectively;
saw weight. 8.1 kg.

Start according to the instructions

Different models of chainsaws have their own starting characteristics and their own mechanisms. We will consider the algorithm for starting the device using the example of the popular model of the STIHL M.S. 180 chainsaw.

Before starting the starting process, it should be noted that the instructions for some models of chainsaws say that before starting the tool, the emergency stop brake should be applied to ensure additional safety. But with a fixed brake, starting will be more difficult.

Accordingly, it will be better to unlock it.

If everything is done correctly, then nothing difficult will be. If you are worried that without fixing the chainsaw at the time of launch, it will cause harm, then it is better not to take risks at all and not get to work. So, the algorithm for launching the STIHL tool is as follows:

Before starting the tool, the choke adjustment lever should be moved to the lower position. Remember that it only moves to the bottom on the saw when the throttle button is pressed. Press the gas button and move the lever down. This will close the carburetor flap and lock the gas in the pressed position;
Next, pull the starter handle with vigorous movements until you hear the characteristic sound of an attempt to start the instrument. It should die out immediately. Then the throttle position adjustment lever is moved one step up;
In this position, pull the starter handle again until the saw starts. And if it starts, then due to the fact that the throttle stick is fixed pressed, the work will take place at high speeds;
Then press and release the gas button once so that the throttle adjustment lever automatically takes the operating position, and the speed decreases;
If it is necessary to put a heated chainsaw into operation, you need to put the lever in the working position, and then start it;
To stop the operation of the engine of the machine, the choke adjustment lever must be moved to the up position.

Chainsaw Husqvarna 339 xp

the model has a capacity of 2.45 liters. from;
chain size. 35 cm;
fuel tank. 360 ml;
oil container. 200 ml;
weight. 5 kg.

Using the chainsaw. getting ready for work

Before starting to use a household chain saw, you need to carefully prepare the tool.

Preparation stages include:

chainsaw

In addition to refueling, the chainsaw needs lubrication of the saw bodies. A separate reservoir is provided for oil in the tool device;

After refueling with fuel and headset lubricant, the operator should check the tension level of the chain being used. For its adjustment, a separate screw is provided in the saw design. It is located on the right side of the tool, under the protective plastic cover;

In the next step, the operator should check the condition of the fixing screws. When the saw is working under high loads, they are subject to strong vibrations. This leads to a gradual loosening of the fasteners. The result of this is deformation of the plastic case or other, more serious damage.

Before each start of work with the chainsaw, its owner should carefully check the condition of the air and fuel filter. They must be clean, otherwise the engine of the tool will run intermittently.

Checking the presence of grease

Now the important step, we need to check the lubrication. Please note that this is always done, it does not matter how many times you work with the saw. This will protect the tool from unexpected breakdowns and overheating. You need to check the following points:

How much oil is left in the tank;
The condition of the saw blade channels;
The lubricant should be on the needle bearing of the drive sprocket;
Is there any lubrication on the driven sprocket.

Как правильно заводить Штиль 180 видео, How to start Calm 180 video

If you see that the channels are clogged, be sure to clean them and lubricate everything. Tests have shown that Foresta chainsaws use 40% less fuel and lubricant. This makes it much easier to work with them.

Chainsaw oil selection

Especially it is necessary to pay attention to the choice of oil, the operation of the entire tool depends on it. The higher its quality, the longer and more efficiently the chainsaw will serve. You need to buy a special oil that is made specifically for such engines. If the wrong lubricant is used, common problems will be:

Engine breakdowns;
Ignition problems;
The chainsaw will stall, and sometimes just refuse to start;
Saw overheating.

Different parts require different lubricants. one oil will not work for all applications. The choice of this material is one of the most important things when interacting with a chainsaw. The lifespan of the instrument depends on the decision made.

Special lubricants have been created for Foresta saws and the motor oil is perfect for protecting the “heart” of the tool. The chain lubricant is not suitable for the motor, otherwise the tool life may be reduced. Even if the oil is of high quality, but it is not used for its intended purpose, nothing good will come of it.

Foresta saws are specially designed with proprietary lubricants that make working with them easier and additionally protect against overheating.

Tips & Tricks

In order for there to be no problems with the chainsaw and it worked without breakdowns, you should follow the operating rules:

Compliance with safety rules.

Running-in after purchase.

Check chip thickness regularly. If it is small, then you need to sharpen the chain. If the chain is sharp, the chip thickness is approximately 3-4 mm.

Can’t cut with the end of the bar.

It is advisable to replace parts of the same manufacturer as the saw model.

If you are new to sawing, train on low speed models.

Sources:

http://crast.ru/instrumenty/kak-zavodit-shtil-180-na-holodnuju
http://metallvsegda.ru/instrumenty/kak-pravilno-zavesti-benzopilu-instruktsiya-dlya-pili-shtil.html