How to Thread a Fishing Line into a Trimmer Coil? Video instruction

How to Thread a Fishing Line into a Trimmer Coil? Video instruction

Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Preliminary preparation

First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
  • electric and gasoline trimmers with a curved rod without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
  • electric and petrol trimmers with the possibility of installing a knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Video: How to Thread a Fishing Line into a Trimmer Coil? Video instruction


We carry out winding fishing line

Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task. winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

You may also like

  • Hoper brand trimmers and lawn mowers overviewThe development of the Khoper brand in the Russian market began in 2010. Positions strengthened over time thanks to the successful design of technology and...
  • Rolling of frame saws is made with the aim of eliminating the marriage resulting from sawing, and improving the quality of cut.Saws roll on milling machines, passing them along the length between two ...
  • How to choose a gas trimmer. detailed instructionsWith the advent of spring, we, tired of the long winter from the white-gray monotony, sincerely rejoice in the appearance of green grass. However, thi...
  • Angle grinder, which is popularly called the angle grinder, is a universal tool with which you can perform a list of works: cutting, grinding, cleaning metal, wood, stone and other materials. This too...
  • In addition to the above units, chainsaws have a cleaning system for the air supplied to the carburetor, a tire with a saw chain, a starter, a chain tension mechanism, ignition, a silencer, etc.Engine...
  • The STIHL FS 38 trimmer is probably well known to all fans of high-quality garden equipment. People who once tested the brand’s products in practice rarely switch to products of other brands, because ...

Coil with one working antenna

The easiest option and a simple sequence of actions:

  1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding. 2. 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse direction of rotation of the spool on the trimmer product. as a rule, on the inner side of the bobbin an arrow indicates which direction the winding is going.
  4. A small section of fishing line is left free to bring it out. it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the bar of the trimmer.

Coil with two working antennae

In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

  • one groove. both antennae are wound together along one groove;
  • two grooves. each antennae is wound on an individual groove.

For both cases, a 2-3-meter-long fishing line is taken. In single-channel reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar. the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly. this operation is not difficult and with some patience will certainly succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism makes winding on its own. from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the spool is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.