As a rule, before going fishing, you need to check all the gear, the reliability of the connecting loops and the sharpness of the hooks. But do not forget about backing, which is wound on a reel, because the success of fishing in general will depend on how to wind the line on the trimmer. Incorrectly wound, it can lead to a “beard”, which is quite difficult to unravel and which takes a huge amount of precious time, casting distance can be significantly reduced, and in general in such a situation it is better not to fish.
Beginning fishermen, due to their inexperience, pay little attention to the choice of fishing rods and tackle, but the right equipment is the key to the success of fishing. Spools with a spool size from 2000 to 3000, which can accommodate 100 meters of fishing line number from 0.2 to 0.3 mm, are usually purchased.
In addition to sizes, they differ from each other in the way they are wound on a spool. You can rewind the fishing line on the trimmer coil with a straight, cylindrical or conical laying, it all depends on the model. It is also worth paying attention to the country producing fishing gear. If the reel is of Chinese origin, from a cheap series, then always be prepared to entangle the fishing line during casting and occurrence "beards"In addition, the cheap option quickly fails and requires repair or replacement.
With high-quality winding, fluorocarbon must form strictly parallel stacking relative to the spool with the direct winding method, and inclined with a conical one.
How to fix the thread on the trimmer
Winding fishing line on a trimmer is a simple matter, but it requires a certain skill. First you need to firmly fix the reel to the rod. After that, pass one end of the fluorocarbon through all the ears of the rod and fix it on the spool. To do this, you need to raise the coil of the coil, wrap around the fishing line and tie a knot Arbor.
If the thread is hard or thick, then before winding it should be lowered into warm water, after this procedure it will become more elastic and lie more evenly. When winding, it is desirable that there is an assistant who would hold a bobbin with fishing line. In the process, lightly brake the fluorocarbon with your finger or a soft cloth.
Video: How to Wind a Fishing Line onto a Trimmer Bobbin
What should be the length of the working thread
It all depends on the method of fishing and the reservoir. If fishing requires a small length of fishing line, then it should be less, if long-range casting is required, then more fluorocarbon is needed. For quick replacement in traveling conditions, every fisherman needs to know how to change the fishing line on the trimmer. If the reel spool is deep, then approximately two-thirds need to be filled with cheaper thread, and the working fluorocarbon needed directly for fishing should be wound on the remaining part. The winding should consist of a thinner fishing line than the working one, this will increase the density and not fall through the main one.
How to wind a fishing line on a trimmer
During winding, the handle of the coil should be twisted smoothly, without jerking and at high speeds. It is necessary to ensure that the thread lies in even parallel fishing lines. Do not wind a line that is too thick for the reel.
Gently winding fluorocarbon, you should pay attention to how much is left to the side. The optimal distance is 2 mm from the top layer to the edge of the rim.
Every fisherman must know how to wind a fishing line on a trimmer and what backing is. Backing is reeling on a spool of a reel. For this, a thread with a diameter of 0.1 to 0.3 mm is often used. If a thicker fluorocarbon is used as a winding, this can lead to uneven and uneven stacking of the main fishing line. It is extremely undesirable to use wet materials for backing, such as nylon and cotton threads. They are unable to dry completely for a long time, which leads to debate, and replacing the fishing line on the trimmer is an additional financial cost.
The amount of thread needed for backing can only be determined empirically. This will require two spools. First, the required amount of working line is wound on one, and then backing is wound so that two millimeters remain to the edges of the side. After this procedure, the spool with wound fluorocarbon is removed and put on an empty one, on which the thread is wound, only in the reverse order. first backing, then working nylon.
Spool nylon thread storage
How to wind a fishing line on a trimmer. figured out, now let’s talk about storing fishing gear, in particular fluorocarbon on a spool. For a long service life of the thread, you should adhere to several rules, the implementation of which allows you to save money on the purchase of new equipment.
It is important to remember that after fishing, the fishing line and parts of the reel get wet, they should be well dried. Poorly dried fluorocarbon fades very quickly and becomes unusable. It becomes brittle and can break at the most crucial moment. To prevent this, after seasonal fishing, the line from the reel should be reeled up and spread on the floor so that it dries well. This procedure should be carried out with backing (winding). You can dry a nylon thread after each fishing trip, if you go to it once a month.
You already know how to change the line on the trimmer, it will not be difficult. Always store fishing equipment in a dry place, this will guarantee the reliability and durability.