How to wind up a line for a trimmer on a lawnmower

How to wind the line for the trimmer on the grass trimmer

The thickness of the cord must match the parameters of the selected tool. Too thick a line for a trimmer will tangle the thread on the reel, contribute to overheating of the motor and rapid wear of the bushings.

According to the thickness of the line for the trimmer is conditionally divided into several types:

• Within 1.2 to 1.6 millimeters. Suitable for models with power up to 0.5 kW. Often electric mowers;
• From 2 mm to 2.4 mm. This size is the most popular, because it copes with young and stiff grass. Fits on tools with about 1 kW of power;
• From 3 mm to 3.2 mm. Suitable for gasoline-powered units that will mow thick stems of weeds;
• Cort 4 mm. Handles overgrown areas.

To determine what kind of fishing line for the trimmer is suitable for the scythe, you can use one of the ways:

• The thickness of the court should be specified in the user’s manual;
• Manufacturers often put important data on the bobbin, including the allowable diameter;
• Slide the trimmer line through the outlet. It should pass unproblematic.

The shape of the section is also paid attention to, because the thread does not cut, but interrupts the grass stem. Types of cords according to the shape of the section:

• Round. A versatile option that allows you to cut fresh and dry vegetation;
• Multifaceted with 3 to 6 facets. You can mow stiff and thick stems. But the consumption of such a material is quite high, so it is only suitable for specific purposes;
• Figured. Star-shaped or square with notches. The first one is used for cutting freshly cut vegetation.

line for grass trimmer trimmer are made of different materials:

• Nylon line for trimmer made of polyamide or propylene is most suitable for brushcutter. Inexpensive versions with polyethylene in the composition. They are not resistant to stress, can not withstand frequent changes in temperature modes. Polypropylene line for trimmer will last longer if you soak it in water for half an hour beforehand;
• The strongest lines are those with aluminum particles and a diameter of about 4 millimeters.

Do not use metal wire or ropes, which can damage the tool.

Proceeding from the described parameters, you can choose the optimal line for the trimmer for the care of lawns.

How to wind the line for the trimmer on the brushcutter spool: method one

Open the trimmer head before beginning winding.

First, determine the amount of line, which we will wind on the bobbin. The bobbin must not protrude over the edges, otherwise the bobbin will not fit into the cover.

After determining the length of the line, you can proceed with threading it into the bobbin:

The line for the trimmer is folded in half, one edge should be 10-15 centimeters longer. The bobbin is divided into two parts by a central rib. There is a groove on it under the court, which must be bent in half

For threading, you will need force; It is important the direction of winding. The bobbin must have an arrow or inscription indicating the winding side

If there is no pointer, there should be an arrow on the head of the mower. The filament should be wound onto the material as carefully as possible, the thread should be as taut as possible, and then the short end of the filament should be attached by inserting it into the groove on the side of the spool, which corresponds to its diameter. Fix the long edge on the opposite side; Cut the thread with a gap of about 10 centimeters on the end of the fixed line; The thread spool is loaded into the mowing head. The edges of the thread are pulled up from the fixing grooves; The cover is put on and fixed with latches. It must be completely fixed.

How to tuck the trimmer line into the grass trimmer spool: the second method

Some spools can be tucked in another way. Two lengths of line are charged, not one folded in half.

• As in the first case, the length of the new thread is determined;
• One edge of the court is bent with a hook;
• At the bottom of the bobbin there are holes for fixing the line, where the bent edge of the thread is inserted;
• The thread is wound behind the arrow on the spool. The level of the winding should not exceed the diameter of the spool;
• The same is done with the second cell of the bobbin;
• The edges of the fishing line that stick out of the holes must be cut. You can simply turn on the scythe, while rotating them will cut them. The line for the trimmer is cut manually with scissors if the diameter of the court is too large.

Features of trimmer application

Such a convenient, and most importantly, an effective device as a trimmer for grass, there are several variations:

As is clear from the names, the types of grass trimmer noticeably differ from one another. But regardless of the type of this tool, its cutting element may be a trimmer line. Of course, a line set in the grass trimmer reel is not endless. And sooner or later it will be necessary to replace it with a new one.

Consumption of fishing line directly depends on how often the device is used and the amount of work performed. The more grass is mowed and the more often it is trimmed with the grass trimmer, the more active it consumes a line for the trimmer. And, accordingly, the sooner it will run out. This raises the question: how to tuck the trimmer line into the grass trimmer reel?

Not everyone knows the answer to this question. And after all, the winding of the line on the spool plays an important role in the work of the trimmer for grass

For your net trimmer to work correctly, it’s important to wind the new line onto the spool correctly. About how to change the line for the trimmer on the trimmer, and will be discussed in this article

Choosing a Filament

In order to easily wind the line for the trimmer on the grass trimmer reel, it is worth to decide what tasks the garden tool will perform. The thicker the thread, tucked into the head, the more difficult the tasks it will be able to perform. It should be noted that often a universal thread is used, the width of which does not exceed 2 mm. You, in turn, can determine the size, using the following methods:

• Read the information in the manufacturer’s instructions;
• check the suitability of the fishing line for use by yourself by trying to insert it into the hole of the spool;
• Examine the bobbin for information on the diameters allowed to be used.

You can choose a line for winding into a grass trimmer reel according to the type of engine. For example, excessively thick filament can affect the increase in rotational resistance. Because of this the load on the engine will increase, which will certainly affect the quality and duration of its further operation.

Avoiding negative consequences is not difficult. For this, you need to keep in mind that for electric motors with up to 500 watts of power, a trimmer line with a diameter of up to 1.2 mm is ideal. If you can not get such a thread, you can use 1.6 mm cord. 2 mm cord, in turn, is used for engines with more than 1 kW. It is worth noting that 2 mm cord is often used for winding on a bent mower. If the gasoline unit has a straight shaft, you should use a thread of 2.5 or 3 mm. The thickest lines are installed only on devices, the power of which is equal or greater than 1.3 kW.

Last, but not least, is the type of cross-section of the line. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several in-demand cross-sectional options:

• Twisted. has a small margin of safety, due to which it is suitable only for young grass;
• serrated. characterized by sharp edges, suitable for work on overgrown areas of weeds;
• Round. the most common cross-section. These lines work well with fresh grass, but are not suitable for shrubs and dead wood;
• Rectangular, square and star-shaped cross-section types are used for working on lawns because of their low strength.

The strongest and most versatile cord is a two-piece trimmer line with a circular cross-section with a core inside. It is this kind of thread that is suitable for carrying out most of the work. It should be remembered that the use of fishing line, ordinary wire and other third-party materials as cord carries a danger to others.

Removing and Disassembling the Spool

To correctly wind the line for the trimmer on the grass trimmer spool, it is necessary to get acquainted with the structure of the trimmer head. It consists of a protective cover, a bobbin with thread, a housing cover, as well as a spring, which is present only in some devices.

Before beginning to disassemble the bobbin, you must turn off/disconnect all power to the device. The method of operation depends directly on the type of head. The first option is to carry out the following actions:

• The user presses the latches located on both sides of the cover.
• After removing the cover, the bobbin is removed. Some models may have a spring which should also be removed.
• In the center of the body is a screw, which should be unscrewed with an ordinary screwdriver.
• When the fasteners are removed, the gearbox is removed from the shaft by gently rocking the body of the product.

The second option for removing the spool to thread the fishing line into the grass trimmer is to screw the head onto the gearshaft. To carry out this procedure, many devices are equipped with a hole into which you can insert a tool. When the screwdriver is inserted, the user has only to take hold of the body of the product and twist it clockwise. It is noteworthy that this method, unlike the previously described method, is characterized by the simplicity of execution.

How to change the line for the trimmer on the trimmer

fishing line for the trimmer is wound on a spool (bobbin), which is located in the body of the trimmer head for grass. First unscrew the head from the brushcutter bar and open the top cover by pressing on the side latches. Some models just unscrew the body.

Take out the spool, clean it from dirt, old fishing line residue. There are one or two section reels.

Spooling line on a one-section reel

Take 2 m of fishing line, thread it halfway through the special hole inside the spool. The line ends are equally long on both sides of the hole. We wind them both on the groove of the reel in the direction indicated by the arrow on the body (the reverse rotation of the reel on the shaft of the grass trimmer). Do not wind the line to the end of the trimmer. pieces of 10-15 cm, which will work, fix in the grooves on board the coil. A fixation is needed so that the line for the trimmer does not unwind when installed in the head of the grass trimmer.

Reel is inserted into the body of the head, at the same time the free ends of the fishing line are slipped into the holes of the body, put out. Assemble the head, put it on the grass trimmer. That’s it, the line change in the trimmer is done.

How to wind the line for the trimmer on the grass trimmer with a two-section reel

If the spool has two sections, the line for the trimmer fold in half and place the bend in a special groove on the board between sections. Start winding the ends each on its own groove. then everything is as in the case of a single-section reel.

How much fishing line to wind on the trimmer for grass? You can reel in 2-4 m, depending on the product model. In each case it must not be wound too tightly, the thread has to be free to be pulled out in the course of work.

Change the line for the trimmer on the disk

The order of work to change the line on the disk in trimmer is as follows:

• Remove the protective cover from the shaft;
• Lock the drive shaft of the grass trimmer, putting a screwdriver through the hole in the gear bowl to the hole in the hub of the shaft;
• We unscrew and remove from the hub of the drive shaft of the grass trimmer the spool with the fishing line;
• Install the cutting disc on the shaft, combining the slits on the hub washer with notches in the mounting hole of the disc;
• Once again we block the drive shaft of the grass trimmer and tighten the fastening nut. It is advisable to tighten the nut with a pipe wrench, but do not overdo it;
• Put back the blade guard.

That’s it, the lawnmower is ready to work with the cutting disc.

Important! Changing the cutting elements must be done carefully, observing safety precautions. Always read and follow all instructions in the instruction manual. This will guarantee productive, reliable and safe operation of the grass trimmer.

How to remove the reel from the grass trimmer?

To change or wind the filament on the spool it must be removed.

The complexity of its removal depends on the model of the tool:

• Low-mounted tool. The motor is close to the ground. To remove the spool, you need to press the buttons on the side of the grass trimmer. After pressing these buttons, the body opens, where the spool with the fishing line is located.
• Grass trimmer with bent bar. Here you need to turn counterclockwise the special thumbscrew. After that, the spool and the spring in it are removed.
• Tool with straight bar. Hold the rod stationary with a screwdriver or other object. Turning it clockwise removes it. Then disassemble the tool into parts and take out the bobbin.

• If the tool with one tendril is used, about four meters of thread will be needed. This thread is passed through the hole inside the spool, where it can be secured. Next, one end of the fishing line is guided by the arrow. After that the end of this thread is fastened in the groove that is in the bobbin. This is necessary so that the thread could not unwind when assembling the spool. If there is no groove, you should hold the trimmer line with your hand and assemble the bobbin.
• If a double-tangled tool is used, first check how many grooves are present.If there is one groove, the two tendrils will point into one groove. If there are two grooves, each tendril will be directed into its own groove.

In the first case, the desired amount of cutting thread is passed through the hole so that the result is a thread of equal length. Then you have to twist the bobbin on the arrow. Then begin to assemble the tool, holding the thread with your finger.

If the reel is equipped with a semi-automatic mechanism, wind the line for the trimmer as follows:

• The thread is pushed through the hole, which is located inside;
• Fasten the ends of the thread in the grooves on the body.
• The reel is assembled and the special button is pressed;
• After that the line for the trimmer itself begins to coil in the desired direction.

Always remember that the cutting line must be protected from hard things. This will extend its service life.

If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread for a new one.

How to tuck the line for the trimmer into the grass trimmer reel

To replace the line in the trimmer, cut a piece of material of the right size, folding it in half. One of the halves should be 5-10 cm longer than the second.

To properly wind the line for the trimmer on the reel, the middle of the thread, folded in a loop, must be placed in the groove of the central partition. One half of the line is winded tightly around the top part and the other half tightly around the bottom part. The longer part is wound onto the lower part. Wind it in the opposite direction to the direction of rotation of the head. There should be an arrow on the lid or side of the head. it shows the direction of rotation. Make sure you wind it in the opposite direction of the arrow. Do the work carefully, pressing the coil to coil tightly.

Insert the remaining 10-15 cm long ends into the slots on the top edge of the coil, this will fix them. With the ends fastened, the line will not unwind.

If you do not have enough line of the right length, it is possible to wind not one piece, but two pieces. In this case bend the end of the line with a hook and insert it into the slit of the center spool divider. Do the same with the second piece. Now wind first one piece and then the other on your halves of the coil against its direction of rotation.

To tuck the trimmer line into the grass trimmer, insert the ends into the holes in the mowing head and pull them out. Put the spool on the axle and push down so that it sits in place, and pull again on the ends of the cutting filament to pull them out to their full length.

The outermost ends should almost reach the blade guard. Cut off the excess. To do this, you can use the steel plate on the shroud, which acts as a knife and automatically cuts the trimmer line to an excessive length when the head unwinds.

Spool is covered with a protective cap. Slide it in place and press down until the catches click into the grooves. Always check that the cover is in place on the grass trimmer and that the latches click into place, otherwise it could come off during operation. In this case, the bobbin will be thrown by the spinning force.

Do not try to wrap as much material as possible. in this case the spool may not fit and there will be problems with fitting and fixing the cover. It is best if the reel is filled with fishing line so that it does not extend beyond the dimensions of the part.

You can find some single-blade models in addition to mechanical double-blade mowers. They differ in the cutting line coming out of one side only. A reel in such kinds of scythes may not have a central partition, instead of it a slot in the bottom flange is used for installation of a non-working end of a thread, in the upper flange there is also a slot for fixation of the working end.

With the replacement wood in place you can start working. Do not mow thick weeds or brush twigs. this is not a job for a grass mower. To prevent injuries and line breakage, make sure you don’t hit any rocks or branches under the mower.

For lawn mowing, one filling of a spool of reinforced line is sufficient for an area of 400-600 m2.

After the cutting filament has worn out as a result of the work, turn off the mower and remove the cover on the mowing head. Pull the fishing line out of the slot, pulling it to the desired length, and reinsert it into the slot. The amount of material wound on the spool is enough for 5-10 cycles of work, depending on the model of the device. When you put the cover back on, look carefully to see if the grooves where the clips are inserted are clogged, if they are, carefully clean them.

When the line for the trimmer is worn out, you need to disassemble the mowing head again, pull out the spool and rewind the working line for the trimmer on it.

Choosing a line

For the threading of lines into the trimmer head to be successful, it is important not to miscalculate with the choice of consumable material. The thicker the cord, the thicker and tougher the grass it can cut. A universal trimmer line with a diameter of 2 mm is often used. You can find the right diameter for your mower in the following ways:

• Check the manual supplied with your trimmer for information on line thickness.
• Pay attention to the bobbin itself. Sometimes it is marked with information about the possible line diameters.
• Another option is to try inserting a cord into the outlet hole. If it will pass through without difficulty, then the chosen diameter of the line is suitable for use.

Reel for grass trimmer

Choose a cord according to the type of engine. If the line for the trimmer will be too thick, then the resistance to rotation will increase. the engine in this case will greatly overheat and will soon fail. Useful recommendations:

• For an electric device with a motor less than 500 V will suit a thread thickness of 1.3 mm. If you can’t find one, you can use 1.6 mm trimmer line. If the power is greater than 1 kW, then choose a 2mm cord diameter.
• The gasoline grass trimmer has the importance of the shaft mower. For the bent version, 2 mm cord is often used. If the shaft is straight, then install a thread of 2.4-2.5 or 3 mm. The thickest line for your trimmer is used on powerful devices. from 1.3 kW.

Pay attention also to the type of cross-section of the cord. Some popular options:

• The most common lines with a circular cross section. They cut fresh grass well, but do not cope so well with brushwood and dead wood.
• Twisted (spiral-shaped) cord is not very strong, but not bad for thin young grass.
• A serrated cord with sharp edges is ideal for large weeds in a neglected area.
• Rectangular, star or square grass trimmer lines are the smoother way to mow lawns, but they’re not very durable.
• The strongest is a two-piece cord with an inner core and a circular section.

Types of line for grass trimmer

Keep in mind that you can not use wire, metal strings and ropes, as well as ordinary fishing thread instead of fishing line. The device will be dangerous for both the user and others. This way the rope or similar products will gradually start to work together, as a result their ends will unravel and the small pieces will fly apart with great speed.

Block: 3/6 | Number of characters: 2323

How the line head on a brushcutter works Why you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most reels have a pressure spring inside (semi-automatic and automatic). Above are instructions on how to disassemble a grass trimmer head without a spring, t.е. on the manual type head. The principle of dismounting a semi-automatic brushcutter head with a spring inside is almost identical to the above instruction.

The principle of operation of the semi-automatic grass trimmer reel is as follows:

• Inside the head there is a spool, which is seated on the slits, preventing its free movement
• The spool is actuated by a spring that presses it against the slits in the cover structure
• A trimmer line is wound on the guide, the length of which depends on the tool itself. This length is usually 1 to 4 meters
• If the length of the fishing line needs to be increased, the protruding part of the reel is pressed during the operation, so that it becomes disengaged from the splines. The trimmer line winds up from the reel, increasing in length
• After releasing the desired amount of line, release the hold-down, and continue mowing

The advantage of a power line is that it does not require sharpening as often as a metal blade. In addition, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and engine of the tool, as it happens in the case of metal cutting discs.

Knowing the construction and design of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the fishing line into the grass trimmer reel. This is what most special tool owners have difficulty with.

Block: 4/8 | Number of characters: 1782

How the line head works on the brushcutter. why do you need to know how it works?

Depending on the manufacturer, heads differ structurally not only externally, but also internally. Most reels have a compression spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without a spring, t.е. on the manual type head. The principle of disassembling a semi-automatic head with a spring inside is almost identical to the above instructions.

The principle of operation of the semi-automatic grass trimmer reel is as follows:

• Inside the head there is a spool, which is planted on slits that prevent it from moving freely
• The reel is actuated by a spring that presses it against the slots in the cover structure
• On the lead is wound a line for the trimmer, the length of which depends on the tool itself. This is usually between 1 and 4 meters long
• During the work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, by which it is disengaged from the splines. the trimmer line winds up on the filament drum, increasing in length
• After releasing the desired amount of fishing line, you should release the clamp, and continue mowing the grass

The advantage of a tool with a fishing line is that this consumable does not require sharpening, in comparison with metal discs. over, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and the engine of the tool, as it happens in the case of metal cutting blades.

Knowing the construction and device of the types of mowing or trimmer heads, it is necessary to proceed to consider the process of threading the fishing line into the grass trimmer spool. After all, this is the point at which most special tool owners have difficulty.

Block: 4/8 | Number of characters: 1782

Winding line on a grass trimmer

Measured and careful removal of the bobbin from the grasshopper reel makes it possible to proceed directly to the winding of the line. Design features of the head, the number and location of fixing holes dictate the sequence of actions in this operation, as well as determine the methods used. Today there are several varieties of spools, depending on the number of line tendrils and methods of threading it:

Grass trimmer reel with one tendril

Many owners and experts note the ease of operation and threading of the spool with one whisker. Depending on the manufacturer, the length of the line to be threaded can vary from 2 to 5 meters. The end of the line is inserted in the head in a special technological groove or hole, and winding is performed in the opposite direction to the working rotation of the bobbin. On most spools on the outside of the body there are marks in the form of arrows that indicate the direction of travel of the grass trimmer reel.

After winding it is necessary to leave the free end 15-30 cm to increase centrifugal force, which is decisive when extracting the trimmer line in automatic and semi-automatic spools. Thread the leftover end through the working hole on the reel and assemble the head.

Trimmer head with two tendrils

After taking the bobbin out of the reel body, determine the number of fishing line spools (1 or 2). There is no fundamental difference between a single-groove and a twin-groove trimmer head, but careless threading in a twin-groove can cause operational problems. Because of the likelihood of intertwining of neighboring lines of the tool, it may be impossible to remove the new ones after the working tendrils are worn out.

Regardless of the number of lines, we take a line of length from 1 for the trimmer.5 to 3 meters. Winding needs to be done in the opposite direction to the rotation of the head, as winding along the direction of travel will lead to the fact that the line for the trimmer will not be extracted from the bobbin. Once the line for the trimmer is tucked into the reel trimmer for grass, the free ends (15-30 cm) is pushed through the special holes. Then assemble the head in the reverse order of disassembly and check the performance. Do not worry if the ends of the two tendrils are very different in size, because when you start the trimmer for grass, the blade mounted on the protection will cut the excess.

Grass trimmer head with automatic line threading

Some models on the market have a spool with an automatic winding mechanism. The owner only needs to properly tuck and secure the ends in the head, and the winding operation will be performed by the tool itself when it is turned on in operating mode. Incorrect winding of the line for the trimmer in the trimmer for grass with such a head is almost impossible, since the coil itself determines the position of the tendrils. The advantages of an automatic grass trimmer head include the ease of threading the line, while the disadvantages are the frequent breakdowns of the mechanism due to the complexity of design and high cost.

Block: 3/3 | Number of characters: 3075

Tips from

Working with a technique like a grass trimmer requires care and attention. Both novice and experienced mowers must follow safety precautions during mowing. Sometimes confident trimmers let their guard down, make irreparable mistakes and get seriously injured. That’s why it is important to

• Close the coil lid on all latches.
• Never reel in more line than you are supposed to because it is hard to unwind later.
• After filling up the spool, always check that the tool works correctly before mowing.
• Choose quality material that fits the particular trimmer.

Do not attempt to mow coarse grass with thick stems using a fishing line. There are steel discs for this. Work only in protective clothing. Wear goggles and appropriate footwear.

How to coil a fishing line

Unhurriedly completed disassembly of the bobbin spool without losing its parts allows you to proceed to the main task. winding the line into the spool. Technological features of the bobbin’s construction and number of working eyes determine the sequence of actions.

Reel with one working tendril

The easiest variant and uncomplicated sequence of actions:

• Size of the bobbin and length of the original factory bobbin winding determine recommended line length for winding. 2-5 m.
• One end of line is inserted to the fixing technological opening inside the bobbin.
• The line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer product. as a rule, on the inside of the reel an arrow points in which direction the winding is carried out.
• A small section of fishing line is left free for its conclusion outside. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin in working condition.
• The leftover end of the line is passed through the hole in the outer part of the bobbin.
• The bobbin halves are assembled and put on the trimmer bar.

Reel with two operating tendrils

In this type of bobbins should determine the number of grooves for winding the line lying on the inside of the spool:

For both cases, take a line for the trimmer with a length of 2-3 m. With one-cable spools the line for the trimmer is pulled through the through hole, its ends (tendrils) are put together and aligned, and then spooled in the opposite direction of rotation of the bobbin on the boom. inside there is usually an arrow showing the correct winding direction. If there are fixing grooves the ends of line are pushed through or held by fingers of free hand, put into through hole of outer half of bobbin, bobbin is closed and fastened to the rod of trimmer product.

The difference of winding the line in a dual-channel spool is that initially a piece of line 2-5 m long is folded in half (to determine the middle fold), and the loop of the fold is inserted in a special groove between the grooves. Both fishing line tendrils are wound each on its own groove, fixing the tendrils and reel assembly is similar to the above version with one groove.

The first performance of this procedure may seem to be long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show you how to tuck the line for the trimmer into the grass trimmer spool and wind it correctly. this operation is nothing complicated and with some patience will definitely succeed:

Once the cutting filament is worn out as a result of the operation, turn off the mower and remove the cover on the mowing head. Pull the fishing line out of the slot, pulling it out to the desired length, and reinsert it into the slots. The amount of material wound on the spool is enough for 5-10 cycles of work, depending on the model of the device. When you put the lid in place, look carefully to see if the grooves where the clips are inserted are clogged, if they are, then carefully clean them.

When the line for the trimmer is worn out, you need to disassemble the mowing head again, take out the spool and rewind the working line for the trimmer.

The grass trimmer is the most common unit used to cut grass and cut small shrubs. This machine is notable for its ease of maintenance, uncomplicated operation during work, and thanks to its low weight even women can cope with it. It is no secret that high-quality work on mowing grass requires proper selection of cutting tools. As the latter, trimmers use special cutting attachments (discs, knives) or trimmer heads with a fishing line inside. Nozzles and fishing line for the trimmer. it is an expendable tool, but if the knives can be sharpened, then when using up the fishing line it is required to replace it. In this article we will tell you in detail about how to change the line for your trimmer.

How to remove the spool and replace the line for trimmer

Owners of trimmers, mainly beginners, get confused, bordering on panic, when it becomes necessary to change cutting tools or line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply cause it to fail, unaware that it unscrews in the opposite direction. To prevent this from happening if you need to change tools, we recommend that you read the step-by-step instructions below.

• Before you tuck the brushcutter line into the spool, turn off the brushcutter engine or de-energize the electric grass trimmer to avoid injury from accidental start-up of the cutting attachment.
• Unscrew the brush head mounted on the gearbox shaft. To do this, the shaft must be secured by aligning the holes on the washer and on the axle and inserting a metal bar or screwdriver into them.