Is it possible to use tile cutter as a circular. We make a tile cut by ourselves

What can be done from tile cutter

When laying tiles of a house, sometimes it becomes necessary to cut off unnecessary pieces from it, which is simply impossible to do without special equipment. If you do not have such an electrical device, then you can go to the store and buy it. But here one problem arises: too high cost, which imposes additional financial costs. Therefore, if you do not have specialized equipment, then it can be made with your own hands from a conventional corner grinder.

Depending on the design features, these devices are divided into 2 types:

The mechanical is a platform on which the tile will be fixed and cut. Usually take a thick board with a flat surface for this. The guides and the cutting element are attached to it, as which they usually take glass cutter and change the cutting head to the blade. You can see a home.made mechanical tool in the figure below:

The electric device has a more complex design, but it is more practical to use. The principle of its work is similar to the functioning of a corner grind. It will also require a flat platform for its manufacture, on which an electric tool is fixed instead of glass cutter. So that the corner grinder does not vibrate and cut the tiles evenly, for its fastening it will be needed by steel pipes. Electric glass cutter looks like in the next figure:

It is worth noting that on sale there are equipment for cutting tiles with water cooling. Undoubtedly, such devices are the best, since they have more performance, but it is impossible to make them on their own at home. Therefore, this article will consider the process of manufacturing an electrical device. It does not require large financial costs, and every person will be able to cope with its manufacture.

What is required for the manufacture of a home.made tool

The electric device is much more expensive in manufacturing than mechanical, but it is more convenient to work with it, and the quality of cutting tiles will be much higher. For its manufacture, the following will be needed:

possible, tile, cutter, circular
  • table or workbench
  • corner grinder with a diamond disk;
  • metal platform;
  • two steel pipes;
  • fasteners;
  • clamps.

You can save on the equipment if you buy a cheap cutting element, but this is not recommended to do this, since the quality of the cut and productivity of the work depends on it.

Recommendations for the manufacture and operation

The disadvantage of emergency and factory manufacturing electric tiles is the formation of a large amount of dust during cutting. However, the manufacturer is equipped with a lot of the tool for this work for connecting to the vacuum cleaner. The corner grinder has no such node. To make it, remove the native protective casing. Instead of it, a new element of a similar shape is welded made of steel with a thickness of 1 mm, but with a nozzle.

The first difficulty is to make a tile from a corner grinder with your own hands, but it is not the last. In the process, new problems will arise, if you do not know some nuances of cutting. The second difficulty is the choice of a diamond disk. There are two types of them:

  • Dry cutting disk has a working edge with small diamond spraying. He forms a lot of dust during cutting. It is better to use it if there is a pipe connection to the vacuum cleaner or for small volumes of work.
  • Cutting disk is used when you need to cut a lot of tiles. There is no dust, since the cut is constantly moistened with water. However, in a homemade device, you need to come up with a way of supplying fluid. The easiest way is to moisten the disk and the workpiece with water in front.

The third difficulty can arise in the method of cutting, and there are three of them:

  • In a straight line. The method is the easiest and often in demand. The workpiece is cut into two parts of the desired size. Tiles are located closer to themselves in front of a working disk, so that the markup is visible.
  • In a straight line with a beam. The cutting process is similar, only the angular grinder is installed so that the disk is tilted at an angle of 45O. Most often, a cut workpiece is already trimmed in this position, forming a chamfer on its edge.
  • Figure harsh. The most difficult thing is to cut a circle under communication in the tile. However, this can be done, only its minimum diameter will turn out 100 mm. First, a circle is drawn on the workpiece. Cross-stress lines are divided into 4 segments. First, the corner grinding is cut through the circular marking with alternating short cuts. Make them undermined. Cross lines are cut through the next step. Drings are already making through. The resulting segments are broken out of tiles. The edge of the circle is polished with a file.

To cut a circle on the tile, make a series of short cuts on marking with any method of cutting always carried out on the front side of the tile. If cut in the reverse order, chips are formed on the decorative layer.

Advantages of tile cutter

Electric tile cutter is quite an expensive device and if you are not a professional tile, but make a simple repair, then buying it is not justified If we make tiles with our own hands, then it is necessary to use the corresponding disk. In order to prevent the appearance of dust during work on cutting tiles, it is necessary to equip the tool with a special container with water. In most cases, it is attached under the disk. During the period of work, the disk on the lower side is dipped into the water and washed off dirt and dust. This provides the most accurate work on cutting tiles.

The advantages of an electric tile cutter from an angular grinder include:

  • The possibility of sawing durable porcelain tile and stone;
  • The fastest processing of large volumes of the material;
  • Ensuring the possibility of the most even cut;
  • Reducing the level of wear, when compared with a manual tool.

Due to the presence of a large number of advantages, the angular grinder is widely used in the form of a tile cutter among many builders. How to make a tile from a corner grinder can be seen on the video.

Teling cutter circular: nuances of use

Some people are wondering if a tile cutter can be made from a corner grinder, if a circular can turn out from a tile cutter of any brand? There are situations when there is a need for a mini-cycle, and standard tools are too large for any miniature work, for example, to cut a thin sheet of a wood-fiber slab, or when working with wooden platbands.

When using a home.made circular from tile cutter, you should strictly observe the safety rules

When you decide to make a miniature circular out of your tile cutter, remember that in this case you need to pay attention to the number and speed of the speed of the disk plate, which works in a tile cutter like a rudder roller. There should be no more than 4000 revolutions. In addition, for your own safety, take care of the presence of protection, for example, protective casings, which can also be done yourself. In addition, during the manufacture of a circular from the cutter for ceramic tiles, do not forget that it is necessary to prepare a flat working surface, which should be reliable and convenient, otherwise, there may be injuries, including quite serious.

We make an electric tool

First of all, it is necessary to determine how the corner grinder will be located when cutting tiles.

Corner grinder

Option 1

The tile along the plank is served under the angular grinder strictly fixed under the table.

  • This technical solution is the simplest, since it involves reliable consolidation of the cutting disk from the bottom of the countertop and the installation of the guide rail (HP) with the possibility of its regulation;
  • Under the table you can put a bucket of water, which will slightly capture dust, and cool the disk.
  • A lot of dust, since such a tile cutter cuts ceramics throughout the thickness and cannot perform a small incision;
  • Unknown regulation of corner grinders due to her stay under the countertop.

How to Use a Manual Tile Cutter

Option 2

The fixed tile is cut by a grinder, which is attached from above the countertops to rectilinear salam rails.

  • Less dust forms, because you can simply cut ceramics and do not perform through cutting;
  • Available instrument regulation.
  • It is very difficult to make such a tile cutter without certain skills;
  • It is necessary to additionally manually process the surface of the cut of the tile so that it shares it.

If you compare these two tools, then the first will be easier to make in a house. Therefore, we will describe further how to make it.

Advantages of tile cutter

Electric tile cutter is quite an expensive device and if you are not a professional tile, but make a simple repair, then buying it is not justified If we make tiles with our own hands, then it is necessary to use the corresponding disk. In order to prevent the appearance of dust during work on cutting tiles, it is necessary to equip the tool with a special container with water. In most cases, it is attached under the disk. During the period of work, the disk on the lower side is dipped into the water and washed off dirt and dust. This provides the most accurate work on cutting tiles.

The advantages of an electric tile cutter from an angular grinder include:

  • The possibility of sawing durable porcelain tile and stone;
  • The fastest processing of large volumes of the material;
  • Ensuring the possibility of the most even cut;
  • Reducing the level of wear, when compared with a manual tool.

Due to the presence of a large number of advantages, the angular grinder is widely used in the form of a tile cutter among many builders. How to make a tile from a corner grinder can be seen on the video.

Crafts from people’s craftsmen

Everyone remembers a saying about a goal that is cunning for fiction, but our people like to make it in their creative nature. Here are a few photos that show original solutions:

  • The simplest device from a piece of plywood and racks. We see an analogue of the tool with the lower engine location. His role is played by a fixed corner grinder. The frame is assembled from wooden elements, everything is lined with plywood from the outside;

Simple tile cutter from a piece of plywood and racks

Comment! Honestly, a very dubious decision, since just a corner grinder can be cut with exactly the result. Without guide chips will not disappear.

  • But this solution looks much more impressive. The master managed to create a real machine with the upper arrangement of the cutting disk from the same corner grinder;

Corner grinding machine for cutting tiles

  • The guide system made of stainless steel allows you to move it both back and forth and down and down;
  • The whole thing is fixed on the bed of woody stove. On this material, you can easily fix any system of stops and latches;
  • The corner grinder itself is held on a carriage of the same wood-boring plate.

For the manufacture of tile cutter, the old corner grinder is perfect

Homemade tiles made of corner grinder

Homemade tile cutter-macro on this we summarize our material. We examined only three options, but the types of tile cutters exist, in fact, the same amount. If you are aimed at creating something like that, you will find useful information in our article. We hope that it was interesting and informative with us!

Crafts from people’s craftsmen

Everyone remembers a saying about a goal that is cunning for inventions, but our people like to make it in their creative nature. Here are a few photos that show original solutions:

  • The simplest device from a piece of plywood and racks. We see an analogue of the tool with the lower engine location. His role is played by a fixed corner grinder. The frame is assembled from wooden elements, everything is lined with plywood from the outside;

Simple tile cutter from a piece of plywood and racks

Comment! Honestly, a very dubious decision, since just a corner grinder can be cut with exactly the result. Without guide chips will not disappear.

possible, tile, cutter, circular
  • But this solution looks much more impressive. The master managed to create a real machine with the upper arrangement of the cutting disk from the same corner grinder;
  • The guide system made of stainless steel allows you to move it both back and forth and down and down;
  • The whole thing is fixed on the bed of woody stove. On this material, you can easily fix any system of stops and latches;
  • The corner grinder itself holds on a carriage of the same wood-boring plate.

For the manufacture of tile cutters, an old corner grinder is perfect homemade tile cutter from corner grinding grounds. Home-made tiles-macro

We will summarize our material on this. We examined only three options, but the types of tile cutters exist, in fact, the same amount. If you are aimed at creating something like that, you will find useful information in our article. We hope that it was interesting and informative with us!

What tool can you work with

You can collect homemade tiles, but this is far from always required, because the process of assembling itself will take a lot of time from you and will also require a certain tool. For example, to make a strong bed, you will not be without a welding machine, which already imposes certain difficulties.

Working with tiles made of ceramics, you need to understand that it will not work to avoid its cutting

Therefore, for starters, we will tell you what you can work with when laying tiles without expensive equipment, and without which it will not work out without any way.

    One of the simplest devices is classic glass cutter. He copes only with thin ceramic wall tiles. As an option, it can be used, but there is a more interesting and convenient solution for the same money.

Glass cutter can be used for cutting tiles

Types of manual glass cutters

Tile cutting glass cutter

Metal devil with a winning tip

Tile plumbing

Tile cutting scheme using glass cutter, matches and forceps

Even if you can assemble homemade tiles, without electric abrasive cutting, laying tiles is almost impossible.

  • Firstly, when passing window and doorways at the corners, it is necessary to make Mr.
  • Secondly, today in the bathrooms put out sockets, hoods and other equipment, under which you need to make holes in the tile. You can perform them with a corner grinding or use an electric drill with nozzles of ceramics.
  • Thirdly, porcelain tile is mainly on the floor today, and it is very difficult to cut it with manual tiles, even professional.

When laying tiles, you can not do without electric abrasive cutting

What tool can you work with

You can collect homemade tiles, but this is far from always required, because the process of assembling itself will take a lot of time from you and will also require a certain tool. For example, to make a strong bed, you will not be without a welding machine, which already imposes certain difficulties.

Working with tiles made of ceramics, you need to understand that it will not work to avoid its cutting

Therefore, for starters, we will tell you what you can work with when laying tiles without expensive equipment, and without which it will not work out without any way.

    One of the simplest devices is classic glass cutter. He copes only with thin ceramic wall tiles. As an option, it can be used, but there is a more interesting and convenient solution for the same money.

Glass cutter can be used for cutting tiles

Types of manual glass cutters

Tile cutting glass cutter

Metal devil with a winning tip

Tile plumbing

Tile cutting scheme using glass cutter, matches and forceps

Even if you can assemble homemade tiles, without electric abrasive cutting, laying tiles is almost impossible.

  • Firstly, when passing window and doorways at the corners, it is necessary to make Mr.
  • Secondly, today in the bathrooms put out sockets, hoods and other equipment, under which you need to make holes in the tile. You can perform them with a corner grinding or use an electric drill with nozzles of ceramics.
  • Thirdly, porcelain tile is mainly on the floor today, and it is very difficult to cut it with manual tiles, even professional.

When laying tiles, you can not do without electric abrasive cutting

Homemade electric tile cutter

The tiles can be independently constructed from corner grinder. This complex process, but it turns out a very practical tool.

For cutting tiles, an angular grinding machine is often used, but it is difficult to achieve an even cut, in addition, it forms a lot of dust, there is no comfort when working.

The proposed version of the tool excludes the above shortcomings. Even a person who does not have special skills and technical knowledge can make it.

  • Corner grinder. You need to use a completely working tool.
  • Metal plates. Their thickness should be 5mm, and the size of the plate is about 150x60mm.
  • Metal ring. Its width should be 20 mm, the inner diameter coincides with the diameter of the flange on the corner grinder. You can make it by cutting off part of the pipe with the desired parameters.
  • 300x200mm textolite sheet and about 30 mm thick. This will subsequently become the basis of the device.
  • Four nuts 10mm, three bolts 10mm, self.tapping screws.
  • Metal elements processing tools.
  • Drill and set of metal for metal.
  • Welding machine.

How to Cut Tile with a Wet Saw

Production

From metal plates you need to cut:

  • Three parts in size 40x45mm. One short side must be stuck to get a semicircle, so at the end of installation the corners will not interfere with the rods rotate around the axis. In the center of each element, the hole Ø10mm must be drilled;
  • One part of 40x100mm in size, which will become the lower part of the mechanism. It must be fixed with bolts to the base from the textolite. For fastening, you need to drill two holes Ø10mm;
  • One. 40x80mm, acting as the upper part of the mechanism;
  • One detail with a Mr.-shaped irregular shape, which will become a lever. To the long side you will need to attach an angular grinder. The other side must be planted on the central axis through the hole made.
possible, tile, cutter, circular
  • From a metal ring, make a clamp that will be installed on a support flange. To do this, remove part of the circle (approximately 10mm). To the outer diameter of the ring from the two ends of the remote part, weld one 10mm nut so that the bolt can screw into them. Tightening the bolt, the ring should be compressed.
  • Further, the resulting clamp, it is necessary to weld to the edge of the long part of the M-shaped element.
  • Metal blanks should be put on a central axis from a bolt 10mm, pull it off and weld so that the lever of the mechanism can rotate around its axis.
  • Screw the rocker device to the stove from the textolite through the holes at the bottom of the mechanism.
  • Equip a support flange on a corner grinder with a clamp, choosing the most convenient location. Tighten the clamp and fix the tool. The sawing disk should not touch the edge of the textolite.
  • On top you need to install a shield for protection, which must be grabbed by welding.
  • To the upper part of the device, you need to weld a small hook or loop. Attach a spring to this part, the length of which is compressed about 50 mm. It needs to be pulled so that the drive instrument stands in position so that the lower part of the cutting disk is above the base.
  • The other end of the spring must be hooked by the hole in a small corner, which must first be fixed on a textile plate using a screw.

Electric tile cutter is ready. They need to cut them, moving the device along the marking line.

It is not so easy to saw tiles with a homemade tile, but at the same time it is not so difficult. The main thing is to have a “hard” hand and a “sharp” eye.

Of course, it can not be compared with a professional tool, but if desired, you can do the necessary work with such a device.

What is required for the manufacture of a home.made tool

The electric device is much more expensive in manufacturing than mechanical, but it is more convenient to work with it, and the quality of cutting tiles will be much higher. For its manufacture, the following will be needed:

  • table or workbench
  • corner grinder with a diamond disk;
  • metal platform;
  • two steel pipes;
  • fasteners;
  • clamps.

You can save on the equipment if you buy a cheap cutting element, but this is not recommended to do this, since the quality of the cut and productivity of the work depends on it.

Choosing an electric motor for a tile cutter

To make a tile cutter with your own hands using an independent electric motor, the selection and installation of the gearbox is required to manually install the necessary speed of the disk rotation. It is not easy to do this technically, so another solution is common-the use of a small corner grinder (a greenhouse for discs with a diameter of 115-125 mm) with a manual adjustment of rotation speeds.

Circular saw from tile cutter. A small review

A small circular of the house made of tile cutter is a convenient and functional tool for sawing small woodwork. With its help, you can cut the plywood sheets, saw boards, cut the beam, skirting boards, platbands, etc.D. Having bought transition rings and the saw on wood itself, we get a small circular for working at home. In this video you can see how to make a circular with your own hands from a tile cutter. http: // www.YouTube.COM/Channel/UCQXVL8LFGTASPC9IAYD0PPG. Link to my channel https: // www.YouTube.COM/Watch?v = nxpzlg91pdk. Review of eccentric grinding grinds Makita-Maktec MT924 https: // www.YouTube.COM/Watch?V = ge6rp9ai_yc. Makita rubbish. MakTec MT191 https: // www.YouTube.COM/Watch?V = PHE80OSVDQC. Overview of the disco saw Makita-Maktec MT582

© 2005. 2022 “Catalog of websites No Follow”. In the catalog 84988 sites. The rights to all materials posted on this site belong to their authors. Hosting Place advertising

Circular saw from tile cutter. A small review

A small circular of the house made of tile cutter is a convenient and functional tool for sawing small woodwork. With its help, you can cut the plywood sheets, saw boards, cut the beam, skirting boards, platbands, etc.D. Having bought transition rings and the saw on wood itself, we get a small circular for working at home. In this video you can see how to make a circular with your own hands from a tile cutter. http: // www.YouTube.COM/Channel/UCQXVL8LFGTASPC9IAYD0PPG. Link to my channel https: // www.YouTube.COM/Watch?v = nxpzlg91pdk. Review of eccentric grinding grinds Makita-Maktec MT924 https: // www.YouTube.COM/Watch?V = ge6rp9ai_yc. Makita rubbish. MakTec MT191 https: // www.YouTube.COM/Watch?V = PHE80OSVDQC. Overview of the disco saw Makita-Maktec MT582

© 2005. 2022 “Catalog of websites No Follow”. In the catalog 84988 sites. The rights to all materials posted on this site belong to their authors. Hosting Place advertising