Perforator falls out the drill how to repair. Why are they flying out of the punch…

Repair. Lubricated the shank of the storm with a solidol and inserted into the peorator. As a result, the drill stopped holding in the cartridge. ⁠ ⁠

Not. You say that: why lubricate the shank solidol?

“At first I had white sores, on the gums, heaven and head. I smeared them with ointment. And then they passed, but the nose fell off! Who knows how to treat?)))

On the guarantee of PE? Bring to service. Not under warranty, but do not know how to repair? Better bring to service.

Most likely bite fists. It is treated by changing the cartridge. Well, or disassembly-assembly.

There is a castle. If it falls out, or on the shank, the influxes were knocked out, or worse, in the cartridge the matter. This is not from solidol.

Cartridge with one ball. With minimal wear, it begins to fall out. Replace with a cartridge with 2 my. Well, or figure it out and redo it under 2 balls. If possible.

The cartridge died. Or change in the assembly or dismantling to try to fix the old

Try to insert another drill if you hold. The problem is in the storm.

There was the same shnyaga, the new drill was marriage.

It feels like you are veiled to ask for advice about some problems with your body.

And even some kind of motion in my pants, I observe an incomprehensible.

Well, it is clear the same thing: you made a lot, the author, from the abundant amount of lubrication of the drill and jumps out. This is the same for children. Or are we talking about porn?

There are two solutions. Blue island and WD-40

Corporation: “Hate” ⁠ ⁠

In the dynamics of the smartphone there was a melodic trill.

I have already said to this goat how many times, and he answered me: “Yes, we are nothing, but only a couple of times, they do everything, and we do”. If I hear a fucking peorator once again on the weekend, I will break all the wheels to him all the wheels!

“We are still rarely at home, think about how to listen to pensioners and children all day,” my wife reassured it all day.

-Well, what am I talking about, you need to take some measures.

-The pedorator is still okay, but how the furniture begins to move in the evening for 4 hours, where they move it, in our apartments? Cabinet, sofa, table, chair and that’s it, there are no places. Where they unfold it, I will not know the mind Masha did not notice how she began to start.

A bright month hung over a high.rise building, leaning a little, as if wanting to see if everyone fell asleep. The house, immersed in shaky darkness, did not sleep. Somewhere a TV worked loudly, somewhere a not walking dog whined up, someone shouted loudly, either with joy, or with grief. Neither sleeping and Peter, pondering his plan of revenge. The small arrow of the Chinese wall clock stopped at 55, the big almost reached the top three.

Something rustled over the ceiling, it seemed that the neighbor decided to polish the floor in the middle of the night. Peter shuddered, he read somewhere, at three in the morning people have a strongest dream, this is the best time for small dirty tricks. The rustling sound on the floor surface also suddenly disappeared, as it appeared. Peter lay down for another 10 minutes for complete confidence.

He stood out of bed quietly, trying not to wake his wife and daughter, sneaking on tiptoe into the corridor. Quietly pulled on the down jacket, winter boots, clamped the keys in his hands so as not to ring. Holding his breath, opened the front door and emerged a fish into the corridor. Locked the castle with the noiselessness of the ninja and only after that allowed himself to exhale noisily.

Sliding with a shadow on the freshly blank wall, went out into the yard, lit a cigarette. While smoked, I thought about the eternal, about what to do. Once he even wanted to quit this stupid venture and turn back, sneak up quietly into the house, lie down in a warm bed, hug his wife. Looking around and making sure that there was no one around, Paul quickly drove away these treacherously cowardly thoughts. He quickly found a blue box, by a misunderstanding the named car, sat down near the rear left wheel and carefully pulled out an awl from his jacket.

“I’m nothing, I’m simple here, I tied the laces,” Paul jumped sharply and turned in place. The heart pounded mercilessly. “What laces, what am I carrying,” flashed in consciousness, pounded in the temples Who is he, why is he here, does not look like a cop, an old.fashioned double.breasted black tweed coat, high.quality black gloves made of thin leather, varnished shoes with a sharp toe. This gentleman, differently, did not turn to call him as if he had come off the TV screen or from the pages of a penny book of horror. The gray face of an indefinite age is almost completely hidden by a shadow, there were no hats on the head, on the hair spread and laid back, the December snow fell. Which is noteworthy, the snow did not melt, forming a pile on the top of the head.

Previously, as it was, you will break through the wheel, the neighbor is tormented, searches for the spare tire, twists bolts. The bolts do not spin, the key breaks, the three-story match is standing all over the yard-you will see any or expensive.

And now automation, service, no romance. Honestly, I do not advise, it is better to take something from our standard set, if it is hard with money, we can make a special offer. For example, a pedorator. everyone is taking, now it is a big discount, a hit of sales of this month. If you order before the New Year, we have an action from 7:00 on January first to the thirteenth inclusive, free!

Bur was stuck in the wall: how to get out?

A drill can get stuck due to a problem in a removable head or a clamp of a penetrator. You can try to take it out, a little fluid of type WD-40 into the cartridge. leave for a while. Thanks to the composition, the coverage of the clamping device will weaken, the drill can be obtained. If there is no such liquid, take simple kerosene. It is poured, after 10 minutes the nozzle is pulled out. You can tap slightly on the clamp, stag a little bourgeois. After the clamp, necessarily clean and lubricate.

Most often, when the working nozzle is stuck, the most secure method for the peorator is used. Turn on a clean blow, slowly scroll the tool, pull it out of the hole. It turns out the drilling of a reverse well, as a result of the drill, it is possible to extract.

The reason may be poor nozzle quality. It happens that the peorator damages a drill made of soft, cheap metal alloy during operation. Sometimes it can be pulled out if you squeeze it in a vice. Holding the peorator with your hands, shake the nozzle and pull.

Many advise to extract with a gas key. to rotate in the opposite direction. You will have to work longer, but the way is safe for a person and a tool.

But it does not always work to get a drill, then you have to cut it with a corner grinder. And to close the hole. Or around the stuck storm at an angle to the stuck drill, drill several holes, remove a piece of concrete along with a stuck nozzle.

How to pull a jammed drill out of a penetrator

The cartridge of the tool is arranged so that a drill or drill equipment moves along the barrel in it. With an increase in the dialect of the reverse side of the drill (rummage), the barrel does not allow the drill to freely go out. If it is jammed, you can also use the vice. The peoporator is installed and clamped in large locksmith vice so that the case does not suffer. For this use rubber gaskets. The equipment is compressed in a small vice, and with a hammer, the blows are carefully inflicted. Hit in the direction of the drill exit from the cartridge. Experts recommend using penetrating solutions in the process of pulling out.

With improper operation, the drill can get stuck in the wall

How to insert a drill

On the ashorator itself there is also a quick.and.packed mechanism. Reliable fastening of the drill in it is provided with fixation using special balls, which, when closed, are tightly included in the grooves on the lower part of the drill.

In order to fix the necessary nozzle, whether it is a drill or crown, you need:

• take the lower part of the cartridge down (towards the pedorator);
• Holding it in this position, insert the right nozzle;
• let go of the cartridge.

If the balls are not entered in the grooves and the nozzle is staggering, then it is necessary to crank it until the structure is completely closed.

And to insert the drill into the peorator using an adapter, first a removable cartridge is fixed, which has a mount with grooves for the tool. Then the drill is installed directly. To pull out a drill or drill, you need to perform all the above actions again.

Here I would like to note that any manipulations for the installation and removal of a drill or other nozzles are preceded by a check of the working condition of the peorator mechanism. To do this, the unit must be included in the network and, having set the necessary operating mode, click on the start button. If the unit does not make unusual sounds and at the same time does not feel the extraneous smells of Gary or burned plastic, then the tool is ready to work.

If the nozzle is stuck

Like any tool, the peorator of even the highest quality can jam. When performing work, this becomes a problem that has several options and reasons.

Firstly, when the drill stuck in a removable cartridge, and secondly, if the nozzle jammed in the penetrator itself.

Когда проблема в самом зажиме инструмента или съемной головке, то достаточно просто залить немного жидкости типа WD-40 в патрон и немного подождать. The composition will relax the grip of the clamping device and the drill can be easily obtained.

There are times when there are no special mixtures and car shops at hand. The output may be ordinary kerosene. It is also poured, and, having waited for 10 minutes, try to free the nozzle. At the same time, light tapping on the clip and small staggering of the drill are acceptable. After completing the procedure, the clamp must be thoroughly cleaned and greased.

The cause of the malfunction happens in the poor quality of the drill itself. If a cheaper and soft alloy of metal was used in the manufacture, then the nozzle can damage the peorator during operation.

Correct this problem can be in several ways. The first thing you need to try is to squeeze the drill in a vise and, holding the tool in your hands, shake the nozzle and pull it over yourself. If the deformation is not very serious, then the nozzle will be able to pull out.

The second option provides for double fixation with a vice. a pencil on one side, and the drill on the other. Then take a small hammer and beat along the borax towards the exit from the clamp. During such an operation, you can use WD-40.

When not a single method helps, you can try to remove the details of the cartridge and turn the drill in the opposite direction about 90 degrees. However, this technique can completely ruin the details of the clamping device.

But if this option does not work, it is better not to try to disassemble the device. It is better to give such a peorator to the workshop to competent specialists.

It should be noted that in order to minimize such breakdowns, it is better to choose high.quality nozzles of leading brands. As a rule, such investments pay off the long time of the tool.

The nozzle can get stuck not only in the mechanism of the unit, but also in the wall during operation. In this case, a drill or a drill can be tried to release by turning on the return move (reverse) on the device.

If such a method does not work, then the nozzle is released from the clamp, insert another, and, drilling the wall around the stuck tip, remove it. If the drill broke during operation, then its residues are removed from the clamp, and a piece stuck in the wall is drilled or simply trimmed with a grinder at the same level with the working surface.

How to pull a stuck drill out of a penetrator?

The performance of repair work most often requires the use of such an instrument as a peorator. They drill holes and dismantle the surfaces. Any power tool during operation is subject to load, and this gradually leads to faults. Often, after the work performed, the problem arises with the removal of the drill from the tool cartridge. To pull out a stuck drill, you need to work a little.

This kind of problem occurs in two cases:

• The drill in the ceremony cartridge, which is used to nozzle of a conventional drill, jammed
• The part was stuck in the clamping lips of the penetrator

The first problem happens due to the need to use a conventional drill in the operation of a drill, which requires a special cartridge-adapter cartridge for manipulations using a peorator. It is inserted into the clip.

After the end of the work, it often cannot be pulled out by the drill, because the clamping element of the penetrator harshly holds it. To remove the drill, in this case it is enough to use a special composition, for example, WD-40. He will relax the clamp within a few minutes. If there is no such remedy, and the store is far away, you can use ordinary kerosene. After 5-10 minutes, you need to try to remove the drill, tapping the cartridge and at the same time shaking the nozzle. This should help, and it will safely free itself, and the clamp must be cleaned and greased.

The second reason for the jamming of the nozzle may consist in the clamp of the penetrator. This type of interference in work occurs under other circumstances. The nozzle in the drill spin around the axis, sometimes performs weak movements of the reciprocal nature. This happens in connection with the transfer of power to the power tool through the lips of the clamping element and the bottom of the cartridge.

The mechanism of the pea transfers energy differently, therefore the drill in the clamp moves differently. The tool contains rotational-attendant and simply shock working functions. The energy to the device is transmitted by a special boy, which hits the tail of the installed nozzle.

There are special grooves on the nozzle, which are firmly fixed in the clamping element, ensuring the transmission of the moment of rotation. Poor nozzles are made of soft alloy, which is not amenable to heat treatment, as a result, the tails do not withstand the load and become unusual.

What to do if the drill is stuck in the penetrator?

Когда в процессе выполнения большого объема работы сверло с противоположной стороны расклёпывается, вытащить его из пеоратора свободно не получается.

To get a drill from the power tool, two ways are used:

• The stuck drill must be taken in a vice, while the tool, holding in the hands, shake to the sides and pull to yourself.
• In a large vice, using rubber lining, so as not to crush the housing, the peorator is clamped. Then the drill is clamped with a small vice and a small hammer is easily inflicted on it to the side aimed at the exit of the equipment from the clamping cartridge.

In both cases, you can use penetrating solutions.

If it is not possible to pull out the drill directly from the cartridge during turning, then you need to remove the details of the cartridge or try to crank the drill back 90 degrees. Its rotation usually leads to a complete replacement of the components of the clamping element.

So that there are no problems with jamming the drill, it is better to use high.quality nozzles of well.known brands. In the process of working to different surface materials, you need to select the appropriate drill.

If attempts to pull the drill out of the device are unsuccessful, then so that the peorator does not break out, it is better to seek help from the master.

Bur was stuck in the wall: how to get out?

In some cases, the drill can tightly get stuck in the wall or any other surface of reinforced concrete structures. In most cases, such a nuisance happens if a hole is drilled at a small angle of 6 centimeters. There are several ways to extract the tool.

Instructions

First of all, it is necessary to check the presence of a reverse rotation function. If there is one, you need to turn it on and, rocking the tool from side to side, get it out of the wall.

In addition, you can arm yourself with a drill and make another hole near the existing one, and through the loosening of the peorator to extract it from the structure.

If the above actions did not help, you will have to use the gas key. If its size is too large, then you can use a steel plate as a gasket. The key should be wound on a drill and beat on its handle with a hammer from the wall. These movements are not the most convenient, but the method is quite effective.

To extract the drill, you can also use a reverse hammer, which is easy to find in any car repair shop. If this tool is unavailable, then you can connect the peorator to the SDS-sided nozzle and pull the side of the processed surface. This method is effective when the drill stuck at a depth of no more than 10 centimeters.

Recommendations to prevent such cases

In most cases, the use of drills that are manufactured by well.known manufacturers is a reinforced concrete guarantee that the tool will not get stuck in the penetrator. Unfortunately, the modern market is flooded with poor.quality products, so the purchased goods should be checked immediately. To do this, just make several holes in the concrete product.

If after these operations a drill can pass through the shank without unnecessary effort, then this tool is really high.quality. If deformation has begun, then at this stage the product will simply be removed from the clamping mechanism. It is important not to miss the moment of the beginning of these changes in order to prevent serious jamming of the drill in the penetrator.

Such a nuisance may also arise due to the solution to use quite powerful equipment for solid facilities, but leave the drill. Even the highest quality products that are not designed to process any material will quickly fail and deform. Therefore, for each kind of material, special nozzles should be used.

It is important to remember that it is not always possible to independently extract the nozzle from the penetrator. Therefore, you just can not do without visiting the service center, which will lead to a loss of warranty. The fact is that the use of low.quality or inappropriate equipment is a user error.

Preventive measures

After we have sorted out the main causes of the malfunction of the penetrator, as well as the methods of repairing breakdowns, you can distinguish several points on how to extend the life of your shock tool.

• In the case of frequent repair work, cleaning the peorater must be done at least once a month.
• Do not forget to regularly lubricate the details of the device.
• To prevent malfunctions, you should choose a high.quality peorator. Cheap devices are suitable only for work a couple of times a year.
• So that the mechanism does not overheat, and the brushes are not washed, it is worth taking breaks in work. For example, after use for 20-30 minutes, let the pedorator rest 10 minutes.
• And the last. after you have finished work, do not leave the peorator dirty. Be sure to clean it after each use and put it in a special box.

Following these small advice, you can extend your life to your peorator, which will save you time on its repair and money to buy a new tool.

Do not be afraid to disassemble it, perhaps he stopped working due to a small malfunction that can be solved with your own hands.

And remember about precautions, because this is an electrical device, which means that you should carefully handle it.

Watch how to fix a peorator with your own hands, watch in the next video.

If the peoporator stopped hammering, the expediency of repair should be evaluated. Imitation of popular brands, cheap modifications is pointless to restore. they are not designed for a long resource, the cost of repair is approaching the purchase of a new power tool. Models of eminent brands last longer, their replacement is more often caused by the appearance of modifications with additional capabilities, moral wear.

Read also: how to seize the aluminum radiator of the car

The lack of prevention after 100-80 hours of work will inevitably lead to the failure of the penetrator.

How to disassemble the inferator cartridge to replace it or repair

Everyone who once made repairs on their own has a pen.

Without it, it is impossible to drill holes in the capital wall of the house.

In addition, the peorator is able to knock down the old tile, knead the solution in the basin and even hammer nails!

Unfortunately, all these works can disable the tool.

How to disassemble the cartridge of the penetrator and perform its repair or replacement?

How is the infantry cartridge

The device is not too complicated. Before disassemble the fast.packed cartridge of the penetrator, it is advisable to familiarize yourself with it.

There are two main types of cartridge-SDS-Plus, SDS-MAX. Sometimes there are other cartridges.

SDS-Plus

Most of the penetrators belong to this type. The cartridge consists of the following details:

• Metal body of the cartridge.
• Spring.
• Lodging spring.
• Metal ball.
• Stop the ball.
• Plastic boot.
• Stop ring.
• Rubber boot.

The metal body of the cartridge is motionless and associated with the shock mechanism. It has a hole for the drill in the middle, in which there are slots holding the drill from the turn. At the end of the hole is an oval groove holding a metal ball.

The spring is installed on the outer surface of the cartridge case and fixed with a plate. The ball is started in the groove on the plate on top, held by a stop, which is limited to a locking ring. On top of this design, plastic and rubber anthers closed the whole design.

SDS-MAX

The device is similar to the SDS-Plus cartridge device. It consists of:

• Metal body of the cartridge associated with the shock mechanism.
• Two oval videos.
• Springs.
• Stretching mechanism.
• Plastic casing.
• Guide for plastic anthers on the case.
• Rubber gasket on the outer part of the case.
• Omentum in the opening for drills and peak.
• Rubber oil seal.

The metal case transfers a blow to the drill and has slot grooves inside, along which a drill or peak is installed. Oval videos are placed on both sides of the case and serve to glorify the drill in the hole. They should not fall inside, jam or burst out. The spring is started on the case and is fixed with a stopping mechanism.

A plastic boot is placed on top, which simultaneously fixes the ball into the groove, squeezing the stopping mechanism of the spring. The plastic casing is oriented according to the plastic guide on the case of the peorator and has grooves. At the end, a rubber seal is placed outside the housing, the oil seal inside the housing and rubber boiler.

Other cartridges

From other cartridges, it is worth mentioning a replaced cartridge for some Bosch models. It is equipped with two nozzles. If desired, you can remove the SDS-Plus cartridge and install a fast-packed cartridge for the drill.

The device for drilling and peaks is similar to the usual cartridge for other peorators of the same size. At the bottom there are fixing elements and a groove, according to which it holds on a quick.sitting mechanism.

In the upper part there is a cartridge case on which there is a ball, a spring, a plastic casing, stopping and stubborn rings, a rubber boot.

The nozzle for the Sovers and the Meshoks is the same as that of the usual drilling cartridge. It consists of two parts connected by a mobile thread with a small step. The upper fast.packed plastic is made of plastic, and for its dismantling it is required to remove the fixing upper wide ring. Then the cartridge is easily disassembled, clamping fists are removed and it is possible to maintain it.

Dismantling of the SDS-Plus cartridge with the replacement of the sleeve

Often there is a need to replace the sleeve on which the amurator’s cartridge rests. To do this, it is necessary to disassemble, removing the boot, stopping and stubborn rings, remove the ball and spring and remove the plastic casing.

After that, you can remove the fixing videos and the cartridge bushing.

The sleeve consists of a cartridge, a shock bolt and a guide for a shock bolt, if it is necessary to replace it, you can put a new one, or replace the components of the parts.

Sometimes there is a situation when the main nest of the inferator is inserted by a quick-sounding shift cartridge for a drill on the SDS-Plus adapter.

If it is not removed as a result of a breakdown, then problems may arise with the disassembly and replacement of the cartridge.

It will not be possible to remove the rings and the casing, remove the spring, since the rapidly recovery lock on the dimensions will not allow this to do this. Therefore, first you will need to remove the fast.packed cartridge from the peorator.

At first, the fast.packed nozzle weakens, and inside it you can see a screw with grooves for the screwdriver. It is unscrewed and removed to the SDS adapter. After that, it is possible to disassemble the infantry cartridge.

Typical clamping malfunctions

Most often there are two of them: the tool in the node is not fixed or the tool jams and it is not possible to extract it. In the first case, the reason will be the wear and loss of stubborn and fixing rings, the wear of the ball, wear of the tool, wear of the slots in the cartridge case. In the second case, the reason is usually a poor.quality tool in which the shank has grinned as a result of impacts.

This usually happens on SDS-MAX and jack hammers with this shank.

In the first case, you can repair the infantry cartridge with the replacement of parts. In the second. you have to disassemble without taking out the tool. In some cases, this is possible, in others. you will have to saw off part of the drill or peak with a corner grinder, remove the sleeve and pull out the fragment from the other side. Only a quality tool for this model should be used.

Highlight it and click Ctrlenter to inform us.

Elimination of other breakdowns

In addition to problems with buttons, brushes and shock mechanism, there are a number of other malfunctions that can be repaired and repaired at home. And for this you will also need the ability to disassemble the peorator.

The drill was stuck

If the drill does not hold in the cartridge, then you should pay attention to a small metal ball. It should be replaced or fixing the spring. When the drill is stuck, the problem is insufficient lubrication.

When the drill is not inserted or not pulled out, the problem lies in small details. You should disassemble the mechanical part and see the cause of the breakdown. As in the case when the drill hangs in the cartridge, the cause of this may be a ball defect.

Stopped working

If your peorator has become worse beaten, it is possible that the problem in the worn teeth of the gear on the mobile part of the engine. This could arise due to strong loads or interruptions in the work of the coupling. As with other faulty details, they should be replaced.

Or there is a malfunction of the switching buttons, then it is worth checking the integrity of the wires.

The drill does not hold

If during work you feel that the cartridge does not hold the drill, then this means that the peoporator is faulty, and the best option will be turned off, since it is dangerous to continue work for health.

The problem is most likely not in the drill, but in the cartridge. As in previous cases, the only way out will be disassembled and determine the cause of the breakdown.

A rattle is triggered

This ratchet is called a coupling, it protects you from a breakdown and is a warning signal that the work of the peorater is suitable for the limit. But this signal does not prohibit you to continue work, you just need to take breaks and give the device to relax. Typically, such problems arise only in cheap devices.

It is almost impossible to fix a coupling with your own hands without professional training, and repairs in the service of expensive. Therefore, it is more profitable to buy a new high.quality peorator.

The peak flies out

During operation, the brick is divided into small pieces, which then find themselves everywhere, especially inside the tool. The cause of the peak departure may be pollution of the cartridge with fragments of brick. In this case, the way out of this situation is to clean the cartridge.

Preventive measures

After we have sorted out the main causes of the malfunction of the penetrator, as well as the methods of repairing breakdowns, you can distinguish several points on how to extend the life of your shock tool.

• In the case of frequent repair work, cleaning the peorater must be done at least once a month.
• Do not forget to regularly lubricate the details of the device.
• To prevent malfunctions, you should choose a high.quality peorator. Cheap devices are suitable only for work a couple of times a year.
• So that the mechanism does not overheat, and the brushes are not washed, it is worth taking breaks in work. For example, after use for 20-30 minutes, let the pedorator rest 10 minutes.
• And the last. after you have finished work, do not leave the peorator dirty. Be sure to clean it after each use and put it in a special box.

Following these small advice, you can extend your life to your peorator, which will save you time on its repair and money to buy a new tool.

Do not be afraid to disassemble it, perhaps he stopped working due to a small malfunction that can be solved with your own hands.

And remember about precautions, because this is an electrical device, which means that you should carefully handle it.

Watch how to fix a peorator with your own hands, watch in the next video.

How to remove the infantry cartridge?

For most of the modern peorators, the dismantling of cartridges is quite simple:

• To weaken the fixation, it is necessary to tap the screw head a little;
• Unscrew the screw with a screwdriver;
• Next, you need to hold the cartridge in TISS and scroll the spindle.

Some individual tool models may require a special tool, but mainly the removal of clamps is carried out in this way.

How to disassemble the cartridge?

In order to visually assess the condition of the wear of the cartridge, it should be disassembled. This is done as follows:

• First of all, a rubber boot is removed. It does not have a special mount, but only tightly planted on the cartridge. You can remove the boot by pushing it with a screwdriver.
• Now it is necessary to dismantle the lock ring with a puck. After that, the spring will be released.
• The spring should be removed with caution. The fact is that the locking balls placed under it can jump out, and they are easy to lose.
• When the spring is extracted, you can dismantle the posterior boot.
• The cylinder is recorded by four inserts that pass through the walls of the peorator shaft. To take out the inserts, it is better to use a magnet or a screwdriver with an appreciated sting. It will not work to take them out differently, since there is simply nothing to seize the insert for.
• Further, the cartridge is removed and all its components are examined for damage. In this case, a decision should be made to complete the replacement of the mechanism, or on a separate part.

The assembly of the clamping device of the penetrator is carried out strictly in the reverse order.

How to disassemble the inferator cartridge to replace it or repair

Everyone who once made repairs on their own has a pen.

Without it, it is impossible to drill holes in the capital wall of the house.

In addition, the peorator is able to knock down the old tile, knead the solution in the basin and even hammer nails!

Unfortunately, all these works can disable the tool.

How to disassemble the cartridge of the penetrator and perform its repair or replacement?

How is the infantry cartridge

The device is not too complicated. Before disassemble the fast.packed cartridge of the penetrator, it is advisable to familiarize yourself with it.

There are two main types of cartridge-SDS-Plus, SDS-MAX. Sometimes there are other cartridges.

SDS-Plus

Most of the penetrators belong to this type. The cartridge consists of the following details:

• Metal body of the cartridge.
• Spring.
• Lodging spring.
• Metal ball.
• Stop the ball.
• Plastic boot.
• Stop ring.
• Rubber boot.

The metal body of the cartridge is motionless and associated with the shock mechanism. It has a hole for the drill in the middle, in which there are slots holding the drill from the turn. At the end of the hole is an oval groove holding a metal ball.

The spring is installed on the outer surface of the cartridge case and fixed with a plate. The ball is started in the groove on the plate on top, held by a stop, which is limited to a locking ring. On top of this design, plastic and rubber anthers closed the whole design.

SDS-MAX

The device is similar to the SDS-Plus cartridge device. It consists of:

• Metal body of the cartridge associated with the shock mechanism.
• Two oval videos.
• Springs.
• Stretching mechanism.
• Plastic casing.
• Guide for plastic anthers on the case.
• Rubber gasket on the outer part of the case.
• Omentum in the opening for drills and peak.
• Rubber oil seal.

The metal case transfers a blow to the drill and has slot grooves inside, along which a drill or peak is installed. Oval videos are placed on both sides of the case and serve to glorify the drill in the hole. They should not fall inside, jam or burst out. The spring is started on the case and is fixed with a stopping mechanism.

A plastic boot is placed on top, which simultaneously fixes the ball into the groove, squeezing the stopping mechanism of the spring. The plastic casing is oriented according to the plastic guide on the case of the peorator and has grooves. At the end, a rubber seal is placed outside the housing, the oil seal inside the housing and rubber boiler.

Other cartridges

From other cartridges, it is worth mentioning a replaced cartridge for some Bosch models. It is equipped with two nozzles. If desired, you can remove the SDS-Plus cartridge and install a fast-packed cartridge for the drill.

The device for drilling and peaks is similar to the usual cartridge for other peorators of the same size. At the bottom there are fixing elements and a groove, according to which it holds on a quick.sitting mechanism.

In the upper part there is a cartridge case on which there is a ball, a spring, a plastic casing, stopping and stubborn rings, a rubber boot.

The nozzle for the Sovers and the Meshoks is the same as that of the usual drilling cartridge. It consists of two parts connected by a mobile thread with a small step. The upper fast.packed plastic is made of plastic, and for its dismantling it is required to remove the fixing upper wide ring. Then the cartridge is easily disassembled, clamping fists are removed and it is possible to maintain it.

Dismantling of the SDS-Plus cartridge with the replacement of the sleeve

Often there is a need to replace the sleeve on which the amurator’s cartridge rests. To do this, it is necessary to disassemble, removing the boot, stopping and stubborn rings, remove the ball and spring and remove the plastic casing.

After that, you can remove the fixing videos and the cartridge bushing.

The sleeve consists of a cartridge, a shock bolt and a guide for a shock bolt, if it is necessary to replace it, you can put a new one, or replace the components of the parts.

Sometimes there is a situation when the main nest of the inferator is inserted by a quick-sounding shift cartridge for a drill on the SDS-Plus adapter.

If it is not removed as a result of a breakdown, then problems may arise with the disassembly and replacement of the cartridge.

It will not be possible to remove the rings and the casing, remove the spring, since the rapidly recovery lock on the dimensions will not allow this to do this. Therefore, first you will need to remove the fast.packed cartridge from the peorator.

At first, the fast.packed nozzle weakens, and inside it you can see a screw with grooves for the screwdriver. It is unscrewed and removed to the SDS adapter. After that, it is possible to disassemble the infantry cartridge.

Typical clamping malfunctions

Most often there are two of them: the tool in the node is not fixed or the tool jams and it is not possible to extract it. In the first case, the reason will be the wear and loss of stubborn and fixing rings, the wear of the ball, wear of the tool, wear of the slots in the cartridge case. In the second case, the reason is usually a poor.quality tool in which the shank has grinned as a result of impacts.

This usually happens on SDS-MAX and jack hammers with this shank.

In the first case, you can repair the infantry cartridge with the replacement of parts. In the second. you have to disassemble without taking out the tool. In some cases, this is possible, in others. you will have to saw off part of the drill or peak with a corner grinder, remove the sleeve and pull out the fragment from the other side. Only a quality tool for this model should be used.

Highlight it and click Ctrlenter to inform us.

Removing the cartridge from the pea: repair, replacement

For professionals, replacement or repair of the infantry cartridge will not be difficult. But what to do to those who are not engaged in construction and repair at a professional level? Since any man throughout his life at least once held a drill in his hands, he must be aware of the process of removing and replacing her cartridge.

First of all, you need to determine which cartridge is used in your peorator. The cartridge can be cam, canging SDS and fast.packed.

The latter, in turn, is one- and two-gyls. In the fist cartridge, the drill mount is carried out using the key, which can not be said about the cangy SDS, fast.packed.

To replace the drill in the cangy sds cartridge, you only need to crank it.

The replacement of the cartridge on the ashrater should begin with the study of fasteners. It holds it with a screw rod or spindle. In most cases, the removal of cartridges is not difficult.

However, sometimes there is a stronger fixation that requires patience, as well as additional tools. A tightly fixed cartridge can be removed using a hammer, key and screwdrivers.

• It is necessary to knock on the screw head to weaken the fixation;
• unscrew with a screwdriver;
• Click the cartridge in the key/vice and scroll the spindle.

The device of the infantry cartridge

Almost any construction tool is universal, and the peorator was no exception. There are many different nozzles, cartridges, adapters for them. The basis for the work of any work is a cartridge.

The adapter for the penetrator is used to install a drill directly removed from a conventional drill.

Both nozzles and drills have a huge variety and are selected in accordance with the tasks.

At home, you always need to hold a replaced cartridge for a peorator, since at any time one may well fail. It should be noted that for each type of work it is better to use various cartridges. The main types of cartridges:

To know how to repair the infantry cartridge, you need to study its direct device. At one time, the drill was mounted using movable fists, but progress is not worth.

In SDS, drills are fixed using 2 guide wedges, as well as 2 stop balls. The difference between SDS-Plus and SDS-MAX only in the number of guide wedges. So, the mount is reliable and fast.

Fixing the nozzle itself was simplified: it is necessary to insert the selected nozzle into the cartridge nest, slightly press, wait for the click. So, the nozzle will be well recorded. And the removal of the drill is not particularly difficult: you need to press on the movable cover, as a result of which the boat will be extracted.

Additionally, the peorator can include components in the form:

• revolutions regulator;
• electronic reverse;
• brush reverse;
• fast replacement systems;
• immobilizer;
• indicators;
• anti.vibration system;
• friction coupling.

How the amorater cartridge is disassembled

In the process of disassembling the cartridge, you need to take into account the manufacturer, since the disassembly of the infantry cartridge is significantly different. Today, the list of popular can be attributed:

Consider the process of disassembly on the example of a cartridge for the Bosch Peotor:

• Move the plastic part, remove the rubber seal.
• Using a screwdriver, carefully remove the fixing ring.
• Then a fixing washer.
• Behind the puck is the second ring. It needs to be turned and removed, picing it with a screwdriver.
• Behind the plastic part there is a SDS clamp, which consists of a spring, washer and ball. The first to take out the ball, after the puck and the spring.

Dismantling the cartridge is carried out with various goals in the form:

The Makita Peorator cartridge is identical, with the exception of individual nuances taking into account the cartridge design.

Replacement of the cartridge on the oorator

As noted earlier, not any cartridge will be able to approach any drill. We examined how the process of removing, disassembling the cartridge is performed. To install a new cartridge, you need to perform the following stages in the form:

The choice of a cartridge intended for the pedorator must be approached seriously. The price is the most diverse, but you do not need to waste money, purchasing the cartridge that may not be suitable for your drill. The ideal option is to take a tool with you, if it is a market, or request a consultant assistance, provided that an online store.