Replacing the starter of the Daewoo Lawn mowed Starter. The worst variant of the breakdown

Repair of the starter of the gas tanker, lawn mowers, trimmers for the grass with your own hands

No matter how high.quality gasoline tools you use, everything can happen to it in the process of construction, and at the most inappropriate moment for this moment. Often problems arise due to the breakdown of the starter. It happens that you will get drunk with a gasoline hole for installing the fencing pillars or mowing the grass with a trimmer, you will start starting the unit, and just have time to pull the starter handle a couple of times, as the rope breaks off, and the engine has already started, dashingly wrapping the rest of the cord to the flywheel, the spring bursts run to the new store buy. But these, of course, are extremes.

Today we will consider the most common case when the breakdown is not so serious and show how to carry out the repair of the starter with your own hands if the cord has broken without any destructive consequences or is not wound due to the fact that the spring just flew inside, went out of the cloth. At least initially I want to believe in it. But in order to find out whether it is or not, you will need to disassemble the starter.

How to repair a starter of a benzo.tool with your own hands?

In the case of a break in the starter cord, everything is clear: we take out the old rope, take the suitable one along the length and thickness (you can linen), stretch it through the hole in the coil, tie the knot. Next, we take the spring to the number we need, only after which we fix the handle. and the voila! about how all this is done is clearly shown below.

But what to do if everything is in order with the rope, and the coil (pulley) of the starter is not wound? Consider this issue step by the example of the starter of the ADA Grounddrill gasoline motorized car, having a pulley with two metal antennae for 2 hooks.

In the case of other types of manual starters of the similar structure, which are widely used in gasoline motorcycles, trimmers and motorized carriers, the entire starter repair process will look similar, differing only in some nuances.

Daewoo DLM 4600SP belt

Manual starter malfunction associated with the spring

A dense starter spring with a hook is the main element of the design of a hand starter. In addition to the spring, the starter also includes the following components:

Rating of gasoline trimmers: TOP-15 of the best models of 2021 and tips on how to choose a spring repair-the main component of a hand starter, boils down to replacing the element.

On a chainsaw, for example, it is an element in the form of a circle, inside which a flexible spring is wound.

Springs in this form are sold in the technique store. It remains only to buy a part and replace.

Repair of a hand starter may also imply a replacement for a cord. If it is incorrectly wound on the pulley of the springs, then the generator will not occur.

• Wind the cord from the end of the pulley (done to avoid scrolling);
• The second end of the cord is drawn into the cover of the lid;
• The winding of the cord should continue until it stops, t.e, as far as the length of the rope is enough;
• After winding, the cord is pulled by 15-20 cm, to check the turn of the pulley of the spring;
• After winding, you should also check how the spring works after stretching and letting go (if everything works clearly, it is recommended that the cord is soaked for another revolution).

At portable power plants, the repair of the spring and cord is carried out as follows:

• From the side of the generator there is a circiva circle recorded by three screws that need to be unscrewed;
• Remove the pulley with a spring and a cord;
• Check the condition of the cord, which can be completely removed from the side of the holder (the upper cap of the holder is removable).

Note. Often, a bundle of the cord, which ensures it from above, weakens. To correct the situation, you need to heat the end of the nylon rope with a lighter, and then wind a new knot.

As for the pulley with the spring, it changes in the same way as it was described above.

How to repair a starter on a trimmer

One of the key nodes of the lawn mower is a starter designed to simplify the start of the device engine. Like other details, it breaks periodically. In this case, there are two solutions to the problem: repair of the starter of the trimmer for grass or its complete replacement. The second option is simpler, but expensive. In addition, the required detail first needs to be found on sale, since different starters are used for different models of gasoline. In the presence of free time and screwdriver with a suitable tip, restore the performance of this node yourself, if you know how it works, what malfunctions are characteristic of it, and how to eliminate them correctly. About all this. in this material.

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Daewoo DLM 5100Sve charging unit

Replacing the starter cord

Иногда приходится столкнутся с проблемой разрыва шнура ручного стартера. Rupture of the cord as a rule occurs due to its mechanical wear of the related over time or with improper operation of the technique.

The main reason is in the wrong factory, before the factory of the mechanism you should choose an idle move on the starter, slightly tighten it until it stops and only then attach an effort for the factory.

Also, the starter’s cord is often torn due to the irregular assembly angle, pay attention to that when stretching, the cord should not leave the starter from a large angle.

Another frequent cause of the gap, there may be a partial breakdown of the starter, the guide sleeve (ring, insert) wear out or breaks down, which smoothes the cord output angle. Therefore, the state of this element should be monitored.

And finally, the reason may be the usual wear.

Deciding on the cause of the rupture of the cord and eliminating it, we proceed to the replacement.

To replace, we first need to dismantle the starter. For example, consider replacing the starter cord on a lawn mower with a Honda engine GCV160 model. The starter is attached to the engine with three nuts. They should be unscrewed carefully, as the stilettos of the engine holding the casing can begin to unscrew. By unscrewing the nuts, we just remove the starter and inspect the presence of damage, if everything is fine, then after cleaning and removing the remains of the old cord, we proceed to replace.

The starter’s pulley should be scrolling by tightening the return spring almost to the stop. Then weaken a little, combining two holes, the first. the weekend on the starter case and the second on the pulley.

After that, holding the starter’s pulley in place, we stretch the cord starting the output from the outside to the opening in the pulley, we recommend that you first melt the tip of the cord. After the cord is stretched, we tie the knot on the tip, pull the knot to the opening in the pulley, laying the knot so that it does not protrude beyond the edges of the pulley.

Then, holding on the outside the cord, the goals of the pulley, giving the cord the opportunity to wrap up on the pulley. At the second end of the cord we put on the starter’s handle and also fix it with a knot.

It is worth noting that the length of the cord is limited by the pulley and return spring. Therefore, the length of the cord should be selected in such a way that the return mechanism can without interference with the cord to the starter case, do not forget that in the main models of the lawn mowers the starter handle is put to the control handle!

After installing a new cord, check the operation of the start and return mechanism, if everything is in order set the starter in place! And do not forget, sometimes it is better to contact professionals!

How to make repair of the lawn mower with your own hands?

Those who have land are very familiar with what struggle is weed.

Especially when it often rains and the grass grows not by the day, but by the hour. Earlier, and sometimes even now, this issue was resolved with the help of a good old braid for grass.

But technologies are not standing still and now in this case, assistants such as electric and gasoline lawn mowers help.

The gasoline mower has several significant advantages over electric, such as mobility and lack of danger of electric shock. But there are many drawbacks, for example: high price, a lot of noise, expensive fuel and significant weight.

Electric mowers are cheaper, easier, work on inexpensive energy, and are not difficult to maintain and repair. These advantages become the main reason for their great popularity among buyers of this type of technique.

But despite the pretty good quality, improper operation and a lot of load, they can disable the device. In such cases, you should not immediately carry the device to the repair shop, but try to find and eliminate the cause of the breakdown yourself. over, as mentioned above, electric lawnmands do not have as many nodes and details as gasoline.

The main thing is to have some tools and faith in yourself. In this article, I will just show you how I did my own repair.

AL-KO, the lawn mower of the company, has serious problems in work, namely: the engine stop without load and its strong overheating, was taken as an example. The motor stops, buzzes and start it again, only repeated pressing the Start button helps. The button has to restart almost every 30 seconds, and with further work and more often.

Of course, you can work, but it is very annoying and gives the feeling that somewhere the problem is. Therefore, I wanted to figure out where?

After the mower was working within an hour, the engine temperature was measured. It was impossible to touch him with a finger. He directly radiated heat. If you continue to pay attention and continue to work on such a mower, an electric motor will inevitably fail.

It is necessary to determine the cause of the motor overheating. To do this, remove the top cover of the case, under which the engine is located and its power chains.

The lid is held on six screws with a hat under a cross screwdriver.

Unscrew these screws and remove the lid. upward.

Having removed it, you can see the impeller, the capacitor, two connectors and the engine itself.

At first glance, no special problems are invisible. The engine winding darkened slightly from the temperature, but so far it is not critical.

To more carefully inspect the capacitor, it is necessary to unscrew the mount and pull it out.

The capacitor of some external damage did not show.

To check it, you need to disconnect the capacitor and feed the engine for a short time. If he did not start and began to buzz, then the capacitor is intact, because the engine was launched with him. Disconnect the power and connect the container connector back to the engine circuit.

Next, try to twist the impeller. It is mounted on the axis of the rotor and rotates rather tight.

And the reason for such severe rotation is a mechanical brake, which for safety stops the engine rotation when the power is turned off.

It looks like a sleeve that moves freely from top to bottom, along the rotor axis.

Когда напряжение на двигатель не подано, эта втулка прижимается верхней частью о крышку, на которой приклеено две резиновые полосы. Thus, the knife is inhibited on the rotor shaft.

When feeding, the brake sleeve under the influence of the magnetic field is drawn to the center of the rotor and provides free move.

With a careful examination, this sleeve with the brake noticed that at the time of turning on the engine, the brake is retracted and gives the shaft free rotation, but after 2-3 seconds it is released again and begins to slow down the motor. This should not be. Hence the stop of the knife during operation and overheating of the engine.

To find out what is the reason for this work, you need to remove and disassemble the engine.

To do this, disconnect the connectors and put the device on the side to get to the clamping screws. Access to them closes a knife with mounting elements.

To remove it, first you need to unscrew the knife bolt (cm. Figure below).

Direction of rotation, like a regular bolt, and not with left thread. That is, unscrew it counterclockwise, and tighten the clock.

The head of the bolt is plastic, so using the key, it must be well planted so as not to “lick” the edge.

After extracting the bolt, the knife and its plastic disk are removed.

Under it is a height sleeve. With its help, you can slightly lower the knife.

Adjustment is carried out by the washers put under the sleeve (see. drawings below).

We remove everything, only the engine shaft and the hexagonal screws of its fasteners remain.

The key for these bolts has a distance between faces of 6 mm. Unscrew them counterclockwise. Removing the last screw, with one hand, hold the engine.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Review: gasoline trimmer for the grass “Forester 304”. Good, reliable, tested by time.

The fight against grass in the garden is one of the main troubles, there is one that can be pulled out or rolled, but there is grass for which you need, something serious At the current time, a wide selection of lawn mowers (trimmers) is presented, both electronic and gasoline. Electronic comfortable in calling, but the radius of their deeds is limited by the length of the cable and if there is a need to “fight” with the grass far from the outlet, it is better to use a gasoline trimmer. How to change a fishing line for a trimmer in dry grass just due to a trimmer for an electric grass. When buying a country assistant, his own choice was made in favor of a gasoline trimmer for the Forester 304 grass, the production of the assembly of Chinese comrades, by the way, did not cause any shakes. How did you choose a fishing line for a trimmer for how to change a fishing line for a trimmer I have an electric trimmer for grass de. The choice in favor of a portable trimmer for grass was also made due to the need to mow not only lawn grass, and a large weed (wormwood, burdock) on a relief area where the mobile apparatus was. would not be in place.

Replacement of fishing line on a motorcycle.

How to wind the cutting cord to the coil of motorcycles (trimmer for grass)

The gasoline is manual. All details in the article How to change a fishing line for a trimmer to a forester.304 “(bought a fishing line for a trimmer for a trimmer for grass as. Replacement of fishing line in a reel.

The principle of operation is simple, first we prepare the fuel mixture, dilute the special oil,

intended for two.stroke engines, with AI gasoline. 92 in a ratio of 1:50, refill and go.

Review

The Forester company is a subsidiary of the Gardentrailing holding. This organization has been supporting domestic manufacturers for more than ten years. Lesnik products are one of the youngest in the garden tools and technology markets. In addition to maintaining the domestic market, Gardentraining adapts the products of little.known in foreign companies. Despite the fact that this trademark is little.known, many buyers prefer it in contrast to other domestic manufacturers.

Garden technique TM Forester is represented by electric and gasoline tools in T. h. trimmers. Most of this brand benzocosyles are designed for domestic use. It is worth noting that many companies acquire a forestry technique to ennoble park zones, public places, and t. D.

How to replace or put a starter spring in place?

If everything turned out to be in order with the rope at the starter, the suspicion falls on the coil itself. It is driven by a strip spring rolled into a roll. To change the spring, certain steps should be taken.

• Remove the starter from the lawn mower.
• Remove the starter coil.
• Unscrew the main bolt holding the pulley on the case.
• Pull the exciting antennae and the spring, the strip spring is almost completely straightened or folded by rings of a larger diameter.
• Hold it in advance.
• Check if the spring is valid (there may be rusty stains, breaks, etc. D.). If the hooks at its ends are cut off, the new ones will not be bent. high.carbon steel breaks when trying to bend it. Weakened hooks are suitable for easy bending.
• Make sure that an auxiliary (ordinary) spring with washers in place. These details protect the coil frame from the end of the main spring with the ends. If the washers and the spring are broken, but there are no new ones, do not screw the coil bolt hard, but follow it. it can unscrew and get lost.
• If the main (flat) spring is damaged, insert the same new. Put the hook at the end of the spring in its place and bend it, inserting the turn behind the turn into the space where it should be and should be.

The rewinding of the spring is performed in a minute. Oknovka in this action is gained quickly.

How to replace or put a starter spring in place, watch in the next video.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it will be useful to disassemble it first, and later collect it. This process is not a particularly difficult occupation. For work, a screwdriver with a suitable shape is useful for work.

Everything should be done neatly, observing safety precautions, acceptable, so that the spring does not injure the master when random.

Parsing the starting node

The start.up mechanism is disassembled in order to establish new details of the incorporation broken in the subsequent sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove the pulley neatly (it is necessary to unscrew the head or work with all this, dressing for earlier glasses and gloves);
• determine why the starting mechanism has broken;
• If the spring collapsed virtually one hundred percent, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before that (the photo shows the styling process);

After the spring plate is installed inside the groove, carefully make it twisting

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very rapidly from the coil and can injure the hand with its sharpened edges

To put a spring plate in the same place does not always go out. It often slips, because the samples are required to repeat to the merit.

Starter assembly

The assembly of the starting node is carried out in a row of steps:

The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;

When making the stated manipulations, you must definitely lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled, the jerking off will begin. Because of this, there is a feeling that the spring has flown away. In order to remove such a defect, it is necessary to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starting node will begin to work without shaken. But such an option is temporary. it is better to repair excellently as a razor as possible.

Spring tension

After installing the spring, it should be pulled. For this they make subsequent deeds:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• create a stretch of the spring, rotating the coil in the direction of the back of the clockwise (views);
• make the required number of revolutions indicated in the operating annotation for the used trimmer model for the grass and the corresponding length of the cord used;
• At the very end, the rope is threaded into the hole created for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this by subsequent methods:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes from the 2nd sides of the groove in the coil, into which stick the sprout hook and fix it with a wire.

Replacing a torn cord

A torn rope is replaced in such a sequence:

• an old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to take a stretch of a spring plate, coupled with a partner, so that the edge of the cord does not hit the top mechanism inside.

It is not difficult to assemble a starter on a trimmer and wound a spring, only you should do it intently and with caution. For various models, gas tanks are similar, because they are repaired in a similar way

With all this, there are certain aspects associated with their constructive features.

Urgent repair of the Daewoo lawn mower at home on the day of the order!

If you are well acquainted with the features of your Daewoo lawn mower and you can correctly describe what happened to it, then our employees during a telephone conversation will be much easier to understand whether your lawn mower should be taken to our service center. If you help to determine the presence of a serious malfunction (for example. It is necessary to repair the electric motor). It will save both your time and our time. But even if you do not have the necessary knowledge. We will take into account all your Комментарии и мнения владельцев on the work of the lawn mower.

• We repair both away and in the service center!
• Masters go to any area and in the field.
• We deliver equipment for repair and back!

Our prices

Our company has one of the largest warehouses of spare parts, among the city’s service centers, therefore we can always find the original spare part or choose an analogue in return for faulty details.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.