Resanta trimmer for grass gasoline winding of fishing line. Field winding algorithm • CIMFLOK.COM

How to Wind the Line Spool on a John Deere Trimmer

How to correct a fishing line for a trimmer to a trimmer coil for grass. step.by.step guides video

The first replacement of the fishing line in the coil will raise many questions. In fact, the process is quite simple. The main thing is to know the algorithm of action. Consider the example of the Fubag tool how to correctly refuel a fishing line for a trimmer to a trimmer for grass. For models of other manufacturers, the instruction will also be relevant.

For any electric or gasoline trimmer for grass, you can use fishing lines of different manufacturers. However, the best option is the consumable of the same brand as the tool. We recommend buying a trimmer fishing line for a trimmer here. It is believed that in this case it will benefit the durability of work and even reduce the consumption.

ВАЖНО ЗАПОМНИТЬ! Нельзя использовать для триммера для травы рыболовную леску для триммера или металлические тросики. Такая замена не эффективна и опасна. Трос может травмировать не только самого косильщика, но и окружающих.

As for the length, it is worth counting on the estimated frequency of using a trimmer for grass. The more often, the more it is worth stocking up.

Information about the possible diameter of the fishing line is found on the case Trimmer coils for grass. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose a suitable option, taking into account the features of the processed territory. The larger the diameter, the easier it is to mow hard grass.

Preparation. remove and disassemble the rogue

In most models of electroly and benzotrimmers, to replace the fishing line, you will need to remove the coil. FUBAG tool (electrimmers and benzoprimers) allows you to skip this stage. For the instruction to be universal, we will still consider it in detail:

one. Fix the shaft. Insert a stop element into the corresponding hole. They may be a thin screwdriver or a metal rod.

Unscrew the spool body. In our example. strictly in the direction clockwise.

Unscrew the lid in accordance with the direction indicated on the case.

The preparatory stage has been passed. You can go to the winding of the fishing line.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut. A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

See the information about the thickness of the fishing line in the instructions attached to the trimmer.
Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters.
Another option is to try to insert the cord into the output. If it easily passes into it, then the selected fishing diameter is suitable for use.

A coil for a trimmer for grass can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
The most durable is a two.component cord with an internal core and a round section.

Types of fishing line for a trimmer for grass, keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread instead. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each zone, it is enough to pull the fishing line for the trimmer and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover. Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

Step Three: The Club of the Head Noner

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

Brief briefing

Z-Zila-publications of materials interesting for society. News of technologies, research, world.class experiments. Social Multi-Tematic Information-Media.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Choose a fishing line for a trimmer

So that you can correctly wind the string on a grass grinder, select the consumable of the proper quality and with suitable characteristics. The thicker the cord, the more difficult the tasks can be solved with its help. Most situations use a standard thread with d = 2 mm.

If you do not know which diameter to choose for a mower, you can apply one of the ways:

Carefully consider the bobbin. Most popular manufacturers such as Husqvarna, Stihl, Daewoo, Champion, etc., indicate the parameters of the recommended consumables;
Read the instructions of the device;
In practice, try to place the string in the output hole. The material of the right diameter will pass into it freely.

There are several life hacks to select a thread for a grass grinder:

If the unit has an engine of less than 500 W, then it is worth using a thread with a thickness of not more than 1.3 mm.
The 2 mm cord is perfect for equipment with a power of 1 kW;
If you have a gasoline unit, pay attention to the shaft. Bent models are best compatible with a 2 mm format, 2.4 ≤ d ≤ 3 mm is suitable for direct.
The higher the power, the thicker the string should be.
Buy only high.quality and durable branded consumables from the manufacturer of the unit. In professional stores of garden equipment, experienced sellers will help you buy consumables of the desired parameters.

Installation of fishing line

To wind the cutting thread, you must first get to the coil in which it will be fixed. To do this, first disassemble the Bobin case. There are several ways to do it.

Removing the cover from the trimmer for the grass and its disassembly

The head of the trawoks consists of several details: cover, bobbin and casing. Separate models are equipped with a spring.

The main security requirement for disassembly is a mandatory disconnection from the power supply network. The disassembly process depends on the type of fastening. It can be screw, threaded or using the “comfort” mechanism.

In the first case, it is necessary to squeeze the locks, and then remove the freed cover and remove the spool. If it has a spring, then it is also extracted from the case. Next, using the screwdriver, you need to twist the screw. Depending on the model of the trimmer for the grass, the screw may not be in the design.

The second option implies the presence of a gearbox twisting on the shaft. In the conditions of such a construct, the shaft is first fixed, and then the bobin itself is unscrewed clockwise.

In the third situation, when you have a Comfort type on your kosyl unit, it does not need to remove the braid for the grass to remove the cutting cord from the gearbox.

Winding of the cord

Installation of a new thread in a coil is a simple procedure, but it must be carried out, following a clear algorithm. First you should determine the amount of consumables, and then do the actions described below.

Fold the cord twice so that the difference between its ends is about 15 cm;
In the central side, it is necessary to detect a groove, for which a thread is harassed, pre.bent;
To determine the desired direction of the winding, look at the arrow-index on the bobbin;
Wrap a fishing line for a trimmer opposite to the direction of the arrow;
At the end of the laying procedure, fix the ends to the corresponding grooves opposite;
Cut excess length;
Insert the seasoned coil in place;
Pull the cord from the fixing grooves, tighten it and close the lid.

There is another way that implies that instead of one segment it is necessary to charge two. The cord material in this case is wound in the direction of the arrow until it reaches a level not exceeding the diameter of the coil, the same should be done for the second cell. Previously the bent end of the thread is stuck into the hole at the bottom of the bobbin.

TORO STRING TRIMMER

Summing up the above, we can say the following. Each manufacturer offers a large assortment of trimmer heads. The sequence of refueling and operating rules differ for each type. In addition, do not forget about the different strings diameter. In order to make the right choice, you need to contact the instructions or to a specialist. Not only the result of the mowing will depend on this, but also the cost of using garden technology.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

Stones, small branches and other hard obstacles come across the grass;
The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
poor quality of the cord (it is recommended to purchase high.quality);
The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
Find the middle of the segment of the cord, folding it in half. You will get a loop.
Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
Dress the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.

For a better understanding of the process of changing the tool, you can watch this video.

Problems with fishing line

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

Stones, small branches and other hard obstacles come across the grass;
The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
poor quality of the cord (it is recommended to purchase high.quality);
The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

The thread does not hold

a fishing line for a trimmer flies out

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

Sources:

https://fubag.ru/tips/kak-pravilno-namotat-lesku-na-katushku-trimmera-poshagovoe-rukovodstvo-video/
https://ironplast.ru/pro-svarku/namotka-leski-na-trimmer.html
https://zetsila.ru/%D0%B7%D0%B0%D0%BC%D0%B5%D0%BD%D0%B0-%D0%BB%D0%B5%D1%81%D0%BA%D0%B8-%D1%82%D1%80%D0%B8%D0%BC%D0%BC%D0%B5%D1%80%D0%B0-%D0%B8%D0%BD%D1%81%D1%82%D1%80%D1%83%D0%BA%D1%86%D0%B8%D1%8F/
https://proinstrumentinfo.ru/kak-zapravit-lesku-v-katushku-trimmera-pravilno-video/
https://www.k-n-d.ru/articles/kak-zapravit-lesku-v-katushku-trimmera
https://tehnika.expert/dlya-sada/trimmer/kak-pravilno-namotat-lesku.html
https://tehnika.expert/dlya-sada/trimmer/remont-katushki.html
https://italy-expert.ru/tehnologii/namotka-leski-na-katushku-trimmera.html