The trimmer for the grass does not gain momentum. the causes of the problem and their elimination
Why is the gasoline or electric trimmer for STIHL, Husqvarna, Champion grass is not gaining momentum. why do this common problem have a number of different reasons for the trimmer. While working with the device, you can meet as obvious problems, signs
Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.
If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:
- low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
- The grass was wound on the shaft of the fishing/knife head;
- clogging of the air filter/muffler;
- Balance of the carburetor.
The lawn mower stalls
When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.
But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.
The lawn mower stalls at high speeds
Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.
Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.
In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.
In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.
Why is a Chinese lawn mower not developing momentum?
The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.
The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it
1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.
Another, this is the presence of malfunctions in the power system.
In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.
Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.
Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.
In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.
To find out, try using a braid by loosening the gas tank cover.
If in this mode the device works properly, clean the valve.
When to contact the workshop
If the device is under warranty, at the first signs of incorrect operation, it can be safely attributed to a specialized workshop. Repair will be made for free, regardless of the nature of the damage, if it happened not due to the fault of the owner. In case of breakdowns in the engine, an ignorant person in technology, it is better to immediately contact a specialist. In any case, the degree of seriousness of malfunctions with the unit is determined by the user himself.
Summarize. Both gasoline and electric trimmers for grass are designed for many years of reliable work. Most of the problems described above occurs due to the insufficient attention of the owner to his assistant. Subject to strict compliance with the requirements from the manufacturer and regular maintenance, the manual mower will work rhythmically and without interruptions.
Reasons and repair
I wish to share my experience to restore the desired power of a trimmer power for grass with an internal combustion engine.
Once, first June, I began to notice that my trimmer for the grass of the GT22GES model (manufacturer Echo) began to lose its former power.
In the process of working with grass, even with a small increase in the load (grass higher and thoroughly), the turnover fell and the efficiency of the work was not the same as it was previously.
Previously, a trimmer for grass did not generally notice such obstacles. With a sharp press on the trigger without load, the turnover increased slowly, it seems to be reluctant to.
He took the management of the user on a trimmer for the grass, found in it a section of the malfunction and their elimination. I chose a suitable malfunction in the table, which is described approximately like this: the engine is poorly accelerated or fades.
In the midst of probable circumstances, pollution of the air filter, fuel filter, clogging of the drainage opening of the fuel tank, the spark plug, carburetor, clogging of the cooling system, clogging of the exhaust channel or muffler.
As it turns out, a list of probable circumstances is wide where to start?
At first, the air filter, a drainage hole, an air radiator looked at the visually, all this was in the usual state.
Later I decided to look from the end of the list, in other words, check the exhaust system of the exhaust channel and muffler.
To do this, he took off the candle tip, unscrewed three screws and removed the plastic protective lid of the muffler (in the drawing in the manual under 5). Then unscrewing the two long screws, he carefully removed the muffler, so as not to destroy the two gaskets that are there.
The foreboding did not bother me. The output channel of the motor cylinder (through which exhaust gases emerge from the cylinder) was packed with a gun by 30 40.
So this is the reason for the disorder of the work of my trimmer for the grass!
Caution, so as not to destroy the surface of the piston and prevent third.party goods (in other words, that Nagar) Immediately cleaned the exhaust channel from the carrier, carefully purged the channel using the pump.
I used a knife as a tool (but only with the edge of the channel), and in the depths of the channel a woody and plastic spatula of a suitable size.
The muffler was quite unsuccessful and snus.
After the assembly, he started a trimmer for the grass, warmed up a bit and tried to mow the engine earned like a new one, the power increased noticeably, the grass does not mow, but cuts (a fishing line for a trimmer three mm).
Tupanat 2-in-1 Cordless Grass Shear & Hedge Trimmer. How to install and use？
Read Lawn Mushroom mowing stalls at high speeds
It’s nice that the device began to work excellent and it is doubly nice that he managed to find a malfunction and remove it.
It is possible that such an inconsistent can appear in other models of trimmers, because their design is approximately similar and all trimmers for grass have a graduation channel and a muffler.
CHAIN Trimmer Head !? REVIEW AND TEST #2
The lawn mower stalls
When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.
But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.
The lawn mower stalls at high speeds
Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.
Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.
In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.
In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.
Why is a Chinese lawn mower not developing momentum?
The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.
The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it
1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.
Another, this is the presence of malfunctions in the power system.
In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.
Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.
Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.
In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.
To find out, try using a braid by loosening the gas tank cover.
If in this mode the device works properly, clean the valve.
Some tricks of work with a benzotrimer.
The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.
Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!
Features of the work of a trimmer for grass
All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.
Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:
- turn on the ignition button;
- press the silicone button for pumping gasoline several times;
- close the air damper;
- The gas lever is installed in a position for high speeds;
- first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.
If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.
Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.
Why is a benzotrimer not gaining momentum and strangle
A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops. The device itself is a rather difficult mechanism, because there are many different circumstances of its breakdowns. As a rule, the emerging problems contain an annotation for operation. Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.
Problems with a benzocosa associated with the purpose that this device is not started, specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:
In order to correctly find the knot where the breakdown occurred, you need to study in what circumstances the trimmer stalls for the grass.
If the lawn mower stops when pressing the gas, then the prerequisites are usually subsequent.
- The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.
- The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
- The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
- The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.
Immediately after you started
The unit can stall immediately after the launch, if the carburetor is cesspool or was incorrectly configured. this causes Uneven fuel supply
The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.
The engine also stops when Clotting of the valve
, supplying fuel. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.
The stop may also be called Air suction
In the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.
When opening an air damper
It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence Cracks of the fuel hose
or problems with seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.
All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video
There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.
So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.
Why and what to do if a trimmer stalls for grass
There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:
- wear of engine elements. piston, bearings, crankcase;
- malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
- mechanical damage to hoses, tubes and cables;
- disobedience with the ignition chain.
Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.
Why is a trimmer for grass stalling when pressing gas, increasing speed
If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions with violation of the rules.
The following reasons are also leading to problems with the performance of the device:
With stretching or rupture of the fuel hose in a gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.
If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations
Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.
Why does a trimmer for grass stall at idle
Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.
Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.
If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.
What to do if the trimmer for the grass starts and immediately stalls
If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.
Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.
In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.
Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.
What to do if the trimmer works and stalls for the grass
Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.
Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.
The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor
What to do if the trimmer for the grass overheats and stalls
If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.
Overheating of the unit usually cause the following reasons:
- The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
- a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
- non.compliance with the proportions of oil and gasoline in the preparation of fuel;
- The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
- The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.
If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.
Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.
Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.
How to avoid breakdowns
Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:
- You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
- During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
- After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
- Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.
With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.
Before harvesting gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.
Store a gasoline trimmer for grass in winter is necessary in a warm room
For what reason does an electric braid for STIHL grass do not develop full power
When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.
You can eliminate problems yourself
Eletric trimmer for grass does not develop the required power, because:
- The voltage in the network is below the required minimum for the device more than 10%;
- There was a failure on a smooth launch (if there is such a system);
- there was a malfunction of the brush node;
- The engine winding was burned;
- rotating parts sometimes jamming.
To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.
The repair of the smooth start system is carried out only in the service center.
note! With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.
To establish voltage, you should first check the power.
When burning engine windings, you need to change the electric motor.
Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.
Note! The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.
Low quality fuel use
Benzotrimmer does not gain momentum in case of low quality fuel. He may stall or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for problems with the combustion chamber.
In the presence of sediment, plaque formed on the candles, the old fuel is drained and flooded another, high.quality.
It must be remembered that a trimmer for grass or a lawn mower should be refueling good quality gasoline and those fuel brands that the manufacturer indicated in the technical passport of the device.
Note! Candles should be thoroughly cleaned of plaque, and only after that place again in the combustion chamber of fuel.
Immediately after you started
To another reason why the trimmer for the grass starts and immediately stalls, the fuel valve can be attached. To restore gasoline circulation in the fuel system, it is enough to dismantle the valve and eliminate pollution.
-
The problem may be a malfunction of the ignition module, but with such a malfunction it is best to contact a specialized center.
The trimmer stalls for the grass: the causes and elimination of the problems of Was Last Modified: July 22nd, 2021 By
Read angular grinder with a revolution regulator 125 choice
The unit can stall immediately after the launch, if the carburetor is sipped or incorrectly configured. this causes an uneven supply of fuel. The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.
The engine also stops when the valve supplies fuel clogs. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.
The stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.
For what reason does an electric braid for STIHL grass do not develop full power
When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.
You can eliminate problems yourself
Eletric trimmer for grass does not develop the required power, because:
- The voltage in the network is below the required minimum for the device more than 10%;
- There was a failure on a smooth launch (if there is such a system);
- there was a malfunction of the brush node;
- The engine winding was burned;
- rotating parts sometimes jamming.
To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.
The repair of the smooth start system is carried out only in the service center.
With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.
To establish voltage, you should first check the power.
When burning engine windings, you need to change the electric motor.
Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.
The last problem may also arise in another unit of this company. the STIHL prisoner, and the sharpening of the disk on the scissors will be its solution.
Why and what to do if the trimmer for the grass does not gain momentum
If the lawn mower turns on, but does not reach the given power or suddenly stalls, this indicates the incomplete serviceability of its individual parts. Most often, the problem is provoked:
- bad or too old fuel;
- winding of grass on the shaft of a knife;
- clogging of air or fuel filter;
- engine problems;
- Falf in the spark plugs.
In all cases, it is necessary to disassemble the motorcycle and carefully inspect its main nodes. This will establish the cause of the failure and carry out simple repair.
The most difficult thing is to repair a benzotrimer with malfunctions of the engine, but such a problem is not common
What to do if a trimmer for grass does not develop speed due to poor fuel
If the benzotrimer does not develop full power, the cause may be in a low.quality fuel mixture. Sometimes the engine in this case does not start at all, in other cases it works with jerks and does not reach the maximum speed.
Diagnostics and repair can be like this:
- Remove the spark plugs with a key.
- Inspect their contacts for reddish or dark plaque.
- If the latter is detected, drain the old fuel from the tank.
Switch raid indicates the presence of a large number of inclusions in gasoline. After removing the old mixture, a new fuel must be poured.
Attention! When using a trimmer for grass, it is advisable to use only the gasoline that is recommended by the manufacturer.
Filter pollution
If a trimmer for grass does not gain momentum in full gas, this may indicate pollution of filters. fuel or air. In the first case, too little gasoline enters the combustion chamber, in the second the mixture is not enough oxygen enough.
You can check the serviceability of the system as follows:
- Remove the air filter and run the motorcycle without it.
- See if she is developing a moment.
- With a positive result, change the part to a new.
If the benzotrimer still does not develop revolutions, you need to test the fuel mixture filter in a similar way. If necessary, it is also changed.
It is impossible to operate a trimmer for grass without a fuel filter, it will quickly break
Wear of the spark plugs
If the lawn mower does not gain a given speed, the cause may be hidden in the spark plugs. The diagnostic and repair algorithm looks like this:
- Candles are removed and inspected for plaque.
- If it is, wipe the part from the fuel and dry.
- Cleaned with fine sandpaper.
- Check that the gap between the electrodes is 1 mm.
- Collect a trimmer for grass back.
If the lawn mower is gaining the desired speed again, the problem can be considered solved.
Carburetor malfunction
In some cases, a benzotrimer is turned on during malnutrition of a carburetor, but does not develop the specified revolutions. Repair is carried out according to this scheme:
- Disassemble the unit and check if the cable in the carburetor is weakened.
- If necessary, carry out moderate, but not too strong pull.up.
- Check the settings of the carburetor for compliance with the instructions for the instructions.
- Clean and rinse the knot itself, and then dried and put in place.
- Remove pollution from the drive mechanism and lubricate the cable inside it with machine oil.
If the trimmer for the grass does not develop momentum and stalls after all the manipulations undertaken, you should contact the service. Serious problems of the carburetor and engine are difficult to repair with your own hands, sometimes this leads only to the final breakdown of motorcycle.