Trimmer for grass gasoline assembly of a gas handle. How to look for malfunctions in the mechanical part

trimmer, grass, gasoline, assembly

Electric trimmer for Huter Get-1000s grass: Independent review

No doubt, beautiful and well.groomed lawns love everything. But not everyone likes to care for the grass, not to mention the fact that it requires strength, time and good tools. over, it is on the choice of the latter that the final result and the sensation of the process largely depend. To turn the lace cuts from work into entertainment, you should think about buying a new electric trimmer for the grass: quiet, compact, environmentally friendly and inexpensive. Such as Huter Get-1000s, to which this review is dedicated.

Repair of trimmers must be carried out as soon as possible when the first signs of breakdown appear so that minor malfunctions do not lead to more serious problems. All models are characterized by the presence of such main nodes and structural elements: the drive system (engine), gear rates, the working part (knife or fishing line), belts and handles. Damage can occur in any part, but some nodes fail much more often than others.

Motokosa working on gasoline or electricity (like different models, from various manufacturers) differ in the design and nature of the problems. Some of them can quite simply be eliminated with your own hands, while others will require more major repairs or contacting a service center.

Common malfunctions of electric trimmers

Electric trimmers for grass differ from gasoline devices with a more simplified design. Conditionally electric braid is divided into mechanical and electric part. Accordingly, the same groups of malfunctions are distinguished, arising to these equipment.

Most of the breakdowns can not be visually identified. For this you will need to use various devices. You can visually determine the following:

  • the integrity of the power cable is violated (insulation is broken from it, or it is clearly interrupted);
  • sustaining or jamming of the trigger button;
  • mechanical external damage to motorcycles;
  • problems with the cutting part;
  • stopping braids for grass when clogging with grass;
  • Damage to the fork.

To find out which part has broken in other cases, you will need to disassemble the electric shock and sequentially check the most likely options. At the same time, they pay attention to the external manifestations of deviations from the normal operation of the device. They contribute to the establishment of the cause.

Repair of an electric trimmer for grass will require the presence of the following devices and tools:

Electric braids for grass often do not work due to causes that are not directly related to them, but caused by a decrease in the supply voltage in the network or the ineffective condition of the used outlet used.

Operation and maintenance

This model of motorcycles in terms of its technical features and structure was created for personal implementation.

Before starting operation, you need to check the tension of bolted joints, since they are at times shake and can lead to the failure of the device, harm to the operator and property around.

When working on the Patriot 555 gas station, you need to use special protective clothing: gloves, glasses, shoes, headphones and special skosts.

This trimmer for grass works at a special fuel consistency of gasoline and oil in a ratio of 32: 1.

The manufacturer does not advise using fuel with m lead. You need to use the latest AI-92 or AI-95.

Patriot specially developed engine oil, which allows a significant extent reducing the formation of soot. Therefore, in the annotation for use, this lubricant is spelled out specifically.

How to prepare a high.quality fuel mixture

  • Gasoline is poured into the container to the corresponding mark.
  • Oils for gasoline, and not vice versa, flows oil for a two.stroke engine to the level
  • The mixture shakes it several times until uniform.
  • If a special container is not provided in the configuration, use the usual gasoline canister. Make a mixture in this ratio of gasoline/oil 32: 1.
  • To prepare a mixture directly in the fuel tank of a trimmer for grass is not recommended.

An aggregate with a weight of 10.48 kg is characterized by good mobility due to small dimensions. All control elements are integrated into a pen that has the form of a “bicycle” steering wheel. The handle of a trimmer for grass can be adjusted. The primer contributes to the easy and rendered launch of the motor, especially after a long downtime. The presence of a primer and air filter reduces the load on the starter. Easy access to the air filter provides the possibility of independent maintenance. The Patriot Pt 555 trimmer is equipped with a two-stroke internal combustion engine that carries out its operation on gasoline more than 92 with the addition of special oil. A product with a 52 cm3 motor volume in working mode develops a power up to 3 liters.With. Fuel tank volume 0.95 liters. promotes the work of the motor for a long time. This model of a trimmer for grass can work without forced breaks to cool. The diameter of the cutting fishing line is 2-3 mm. The dimensions of motorcycles within the boundaries of 1582 x 369 x 375 mm meet the requirements of current standards and standards. In the production of a trimmer for the grass Patriot Pt 555, only patented high.quality oils and lubricants were used.

Tank volume, l one.2
Type of bar even
Primer Yes
Weight, kg 7.7
Type of cutting element Trimmer fishing line/knife
Working volume, cm/cube 52
Power, l/s 3

How to assemble a control handle on a Carver trimmer

Electronic trimmers for grass differ from gasoline devices with a more lightweight design. Conditionally electronic braid is divided into mechanical and electronic part. Accordingly, the same groups of problems are distinguished that arise with these equipment.

Most of the breakdowns can not be visually identified. For this purpose, it is useful to use different devices. The subsequent:

  • the integrity of the power cable is violated (insulation is broken from it, or it is obviously interrupted);
  • sank by different jamming of the trigger button;
  • mechanical external damage to motorcycles;
  • obstacles with the cutting part;
  • stopping braids for grass when clogging with grass;
  • Damage to the fork.

To find out which part has broken in other cases, it will be necessary to disassemble the electric costs and alternately check more possible options. Simultaneously evaluate external manifestations of deviations from the usual operation of the device. They contribute to the establishment of the premise.

Repair of an electronic trimmer for grass will demand the presence of subsequent devices and tools:

Electronic braids for grass often do not work because of circumstances that are not specifically related to it, but caused by a decrease in the supply voltage in the network or the non.working state of the used outlet.

Ahead of time before disassemble and repair an electronic braid, you should check the condition of the outlet and the voltage in the network. If its value deviates from the norms indicated in the operating annotation, then it does not even make sense to try to work with a device without a stabilizer designed for appropriate power. Another electric motor may fail. Only after determining the fact that the reason for the trimmer for the grass is specifically connected with the child, of course, begin to analyze the mechanism with the repair purpose.

Trigger handle of gas motor.

Dismantling of the electric ships pursuing the purpose of repairing its electronic part in such a sequence.

  • Put a trimmer for grass on a flat surface (for example, a table) that does not contain excessive objects.
  • Spin the screws of the lids located that.
  • Remove the unscrewed half of the case, getting access to the start button, the electric motor, the brush unit, bearings, electronic connections (these elements are shown in the photo below).

Build a Gearbox for Gasoline Engine 26CC

Brush and bearing nodes are presented in the photo below.

The braid for the grass will work without a thermallara, it will only come in handy for the time without the help of others to inspect the temperature of the electric motor, sometimes letting it cool. It is possible to install a new similar sensor.

The electric motor starting button is an option to check with a jumper with a jumper of its contacts. If the trimmer for the grass earns, then the inconsistent is understandable. But such an option is dangerous. Our client should be done neatly, so as not to get an electric shock. To change the button, you should use a screwdriver to remove it from the place of landing and attach the wiring from the previous to the latest. After the shift, it is necessary to assemble an electric shout, and after checking its performance.

The change of brushes is required if they are destroyed. With all this, it is quite old to remove from the grooves, and the new ones are installed in their place.

The connecting terminals on various models of trimmers are actually similar, therefore, the connection-rejection of the wires is made idytically.

Changing the bearing is a rather complicated operation, as it may not be shot from the motor shaft. Tighten or knock it down carefully so as not to destroy the rotor in other words.

When the electric motor of the trimmer for the grass burns out, and you need to replace it with a new one, you should carefully remove the fan and bearings, and then install them in the same place. In terms of expenses, the change is actually comparable to the acquisition of a new mechanism. Its conduct in the absence of experience working with electric motors is better to entrust to the specialists.

Annotation for the assembly of the electronic part Motokosa is subsequent:

  • install the engine, tightening the fasteners;
  • connect an electronic circuit;
  • The wires are placed neatly between the separate compartments into existing recesses;
  • close the top cover, snapping the locks and screwing it with screws.

After assembly, the device is inspected.

There are enough probable breakdowns of gasoline and electronic trimmers. So that the device is efficient for a long time, it should be kept unsuccessful, in a dry place. The fundamental moment is the implementation of constant preventive measures (for example, the lubrication of the gearbox) and compliance with the operating rules set forth in the annotation to the device. Getting equipment is better than high.quality work from world brands.

Disassembled the mechanism, it is recommended to photograph the process in stages in order to take everything into account, and do not miss a single part when assembling. When substituting parts, you should pay attention to the choice of suitable devices: it is better to use unique spare parts.

In some models, the bar consists of 2 parts-a coupling is used to connect them. Such devices are comfortable during transportation.

Installation of a chain from a chainsaw on a trimmer for grass: increase efficiency

First, preparatory work is performed, the washer is processed. To do this, using a ruler, a straight line for a trimmer on it is noted in diameter. After which the washer is clamped in a vice. In this case, one of the stitch should be located upward.

It is advisable to note the location of the holes of Kern in advance, then the drill will not slip when drilling. Holes are created on both sides. It is important to make them at first thinner, and then thicker. As for the diameter of the hole, the chain from the chainsaw should pass well into it.

Next, the chain is threaded through the hole. It is worth placing it from the inside of the washer so that it does not interfere with the leading axis of the trimmer for the grass.

Should be as responsible as possible to choose the size of the chain. It needs to be freely measured. It is important that it is no more than the required size. Otherwise, the protective shield will crush, and then a new problem will arise. From the inside, the chain is welded directly to the puck.

On this work on installing a circuit in a trimmer for grass can be considered complete. A flat puck, a changed puck, and all this is fixed with a nut is put on a trimmer axis for grass.

Important information

If there are doubts, it is better not to use this tool not according to the instructions. All this can lead to sad consequences. But at the same time, some craftsmen still dare to modernize their trimmers for grass and, as a result, achieve an improvement in their effectiveness.

With such a trimmer on the site there will be not only grass and weeds, but small shrubs will cease to seem obvious.

What can be done from a trimmer for grass

What can be done from a trimmer for grass yourself to facilitate everyday work or for entertainment? This question arises if there is an old unnecessary device, or a equipment is required for operation, which, with factory manufacture, costs much more than a gasoline or electric braid for grass. In practice, many options have been implemented by the craftsmen. The main of them are a motorcycle bike, a snowball player, an ice ax, devices for the cultivation of a land plot and the mowing of lawns, saw, snowmobile equipment. To bring the idea to life, in each case you will need to apply a certain set of tools and additional materials.

A manual starter for a lawn mower or a gasoline trimmer for grass is a mechanical node, which includes a pulley placed on a ratchet. On the pulley in the starting position of the rope wound. At starting, it stretches out. The pulley is spring.loaded. you should release the end of the rope, how it drowns back. As a spring, a flat ribbon shaped in the ring is used. It resembles a spring in large mechanical watches that start once a day.The starter itself is located more often on the rear than closer to the front end of the mowing or trimmer for grass.To correctly produce all manipulations with a starter for a lawn mower, you need to know the features of the device and installation.

Homemade snowman

There are many options for creating equipment for cleaning snow based on a trimmer for grass. The easiest way to upgrade. replace the knife with the rotor. This snowman works like a shovel, but they simply move it in the snow: the device rakes it and takes it to the side.

To make planned changes, you will need the following materials and tools:

  • A straight arrow mower, at the end of which there is a gearbox;
  • Metal barrel, even beer, for example, from the Baltika drink;
  • Trimmer mill with many teeth (used to mow thick grass);
  • Drill with drills;
  • Grinding machine and welding machine.

Instead of keb, you can use a thin metal sheet (tin) 1.5 mm thick.

The assembly process of the snowpipe is performed in the following sequence:

  • Cut in a circle, moving away from the bottom by 15 cm, the barrel;
  • Make a hole for the dental mechanism from below and drill 3 more small holes to fix its screen;
  • The side square of 10 x 10 cm is cut out to shed snow through it;
  • A third of the open front of the trunk is covered with a piece of metal (tin), while the opening for the release should be located on the central inclined junk fishing line;
  • Make a rotor;
  • Make a deflector who directs the abandoned snow in the right direction;
  • Weld it to the case in the place of the hole in order to release the mass of snow;
  • Fix the lower part of the blade;
  • Install the brush gearbox and fix it with bolts;
  • They put the rotor as a simple working knife.
  • The strip is cut out of metal, the width of which is 15 cm, and the length is 30 cm;
  • Bend the workpiece slightly;
  • Welded on the sides of the long side of 10 cm so that snow does not fall at the output.

The rotor is made in the following sequence:

  • Cut rectangular stripes in size 25 by 10 cm from the metal sheet;
  • Cut and grind the plates in the form of blades;
  • They are welded to the disk from a braid for grass.

The spatula is made of material residues. To do this, use a piece of tin from 30 to 40 cm. The edges are bent along the long sides to form a two.centimeter rim.

The snow cleaning mechanism should be used at maximum speed. This will extend the life of the device, as frequent pressure on the gas leads to the failure of the engine. When welding, it is difficult to combine thin metal, as it easily burns it. Therefore, an experienced welder must perform work.

Ice braid

A gasoline braid for grass can be converted into an ice drift. Factory analogues are rather complex and powerful devices. Structurally, the equipment is a screw connected to the engine (in most cases, two.stroke units are installed). Industrial devices are equipped with automatic safety systems that disable ice drift in case of refusal and exclude the possibility of random launch. Models also differ in the number of speeds: one- or two-speed.

For lovers of winter fishing, it is unprofitable to buy a factory unit, and it is difficult to use a portable device with a large thickness of ice in work. This will help save energy and money, turning the old trimmer for grass into ice drift.

In addition to a bush, you will need a drill (factory or homemade) and tools for assembling the final design. The difficulty is to attach the working part to the trimmer. Much depends on the existing braid model for grass.

The following videos show how an ice drill from a trimmer for grass works:

The last video contains a possible attachment of a seeder to a bush.

Pawn Stars Has Officially Ended After This Happened

Compared to industrial analogues, this is a homemade ice discovery device with low energy consumption, but for drilling holes enough with the head. The device also weighs little, which facilitates transportation.

Replacing a torn cord

A torn rope is replaced in such a sequence:

  • an old cord is removed;
  • choose a suitable rope (thickness and length);
  • Having reached it through a special hole in the coil, a knot is tied;
  • Sprinkle a spring, producing the required number of revolutions;
  • Fix the pen.

It is not difficult to assemble a starter on a trimmer and wound a spring, only you should do it intently and with caution. For various models, gas tanks are similar, because they are repaired in a similar way

With all this, there are certain aspects associated with their constructive features.

Analysis and replacement of the bar

It is often necessary to carry out the repair of a trimmer bar for grass. It is a design from such parts:

  • drive shaft of steel, which has multifaceted or square slots on the upper and lower ends;
  • aluminum tubes;
  • a plastic sleeve created to maintain a centralized position of the drive shaft in the tube (so that there is no vibrations);
  • shock absorber made of rubber suitable for connecting the bar with the motor;
  • steering wheel with a handle used for control, and a counter, belt.

In some models, the shock absorber has between the control stand and the bar. All control elements (lock lever, ignition switch, gas button) are placed on the handle.

How to make out a bar and Collect Then it is for lubricating the shaft or its substitution, in detail in the video further. The same method changes the broken bar to the latest.

Often it happens that multifaceted or square slots of the drive shaft “lick”, with all this, the working mechanism does not spin or does it with a penetration. Then the shaft is changed.

When a knock occurs in the tube, you should disassemble the bar and check the condition of the sleeve, and if necessary, carry out its replacement. How true Collect gas handle on a trimmer, is considered in the below.

If there is no rod, which is applicable to installation, then you can tighten the fault with a clamp or apply the likeness of the tire. This measure is temporary, therefore, according to the ability to make a substitution, the ability to make a substitution.

How to fix a trimmer for grass yourself

Repair of trimmers must be carried out as soon as possible when the first signs of breakdown appear so that minor malfunctions do not lead to more serious problems. All models are characterized by the presence of such main nodes and structural elements: the drive system (engine), gear rates, the working part (knife or fishing line), belts and handles. Damage can occur in any part, but some nodes fail much more often than others.

Motokosa working on gasoline or electricity (like different models, from various manufacturers) differ in the design and nature of the problems. Some of them can quite simply be eliminated with your own hands, while others will require more major repairs or contacting a service center.

Dismantling of gasoline braids for grass, lubrication of its parts and replacing faulty elements

In order to disassemble the lawn mower for repair work, in general, such devices will come in handy:

  • set of screwdrivers (with various tips) and wretches;
  • small puller for removing bearings;
  • special candle key;
  • a hammer.

In each case, it is useful to disassemble individual nodes.

It should be noted that the starter (start.up) in a number of models is non.devastated. in this case, with dilemmas with it, only substitution of the element is likely. If the node is disassembled, then it can be repaired by removing and replacing the rope and the spring, or by installing the latter in place (when it exit from the gear).

Clutch repair

When a knife or fishing line for a trimmer when operating a motor at idle is actually spinning every time, and unusual sounds come from the front of the motor, then this shows a breakdown of clutch couplings. A bursting spring is a prerequisite. With all this, the equipment mows normally.

Clutch of a trimmer for grass is repaired in the following way:

  • Remove the lid from the silencer;
  • remove the iron stand;
  • After remove the lids of the cylinder and the starter to gain access to clutch;
  • unscrew the side screws to remove the shock absorber lid;
  • They take out the tube from it, after earlier letting the tightening bolts;
  • unwind the clutch (presented in the photo further);
  • examine the condition of the spring, pads and bearings;
  • The latest spring is clinged, passing the hooks into the proper holes;
  • To replace the pads, it is necessary to remove the spring, and then turn the bolts on their.

As needed, the crankshaft will stop with the help of, for example, ropes.

Ordinary breakdowns of trimmers, how to remove them with your own hands

Like any technically not simple device operating in difficult conditions, trimmers for grass can fail. Very often the causes of malfunctions are the violation established by the manufacturer, the operational rules of a mechanized braid for grass. For example, non.compliance with the modes of alternating work and technological break, or irregular lubrication of the gearbox and other parts, which leads to overheating of parts and mechanisms.

Distinctive breakdowns of trimmers, very often manifested in a variety of types of this device, are considered:

  • The failure of the work head of the tool, which in most cases is loosened in violation of the supply of fishing line due to the reason for its confusion or sticking, and also damage from the mechanical factors of the bottom of the coil;
  • breakdown of carburetor motorcosa;
  • A break in the intermediate shaft of the tool, the basis of this breakdown can be cutting the slots with which it connects to the motor shaft;
  • Damage to the connecting bushings of the root bearing installed between the cable and the head of the trimmer for the grass.
  • fuel and air filters pollution.

In most cases, gluing and confusing the fishing line in most cases occurs with its unfavorable quality and violation of working modes, which leads to overheating of the head of the trimmer for grass and fishing line. To remove this breakdown, you need:

  • Remove the lid from the trimmer head, for which press the latches with your fingers, and carefully unfasten the lid.
  • Remove a reel with a fishing line from the head. It must be removed carefully so that it does not jump out and does not fly into the grass placed under it, the spring.
  • Dissolve a confused or sticky fishing line for a trimmer, and charge it by a new. Fold the fishing line for the trimmer in two, and fix the middle into a specialized groove on the middle disk of the coil, which divides the bobbin into 2 compartments.
trimmer, grass, gasoline, assembly

To wind the fishing line for a trimmer to the coil of a trimmer for grass, first of all, it is necessary to fold it in two, and the middle is fixed in the suitable groove

Having wiped a fishing line for a trimmer to the heel of the head of a trimmer for grass, its free ends must be fixed in grooves on the bobbin

For a trimmer for grass, it is better to use a fishing line for a trimmer of the diameter that is recommended for using the manufacturer of the tool. When purchasing, it is necessary to buy a cord of more popular brands, and not take the first fishing line for a trimmer of lower price and an unfamiliar brand.

If the gasoline trimmer for the grass does not start or stalls its motor after starting, the basis may be a breakdown of the carburetor or pollution of the fuel filter. Damage in the operation of the carburetor can occur when clogging, and sticking on the oil valve film of this device. This can happen if you do not develop a fuel mixture to the end, and leave it in the tank for a long time.

To clean the carburetor, you should remove it from the motor and disassemble, disconnecting the primer (manual pump for pumping fuel), all gaskets and needle. Any detail individually should be washed by the carburetor cleaner, blowing the liquid from the cylinder into all its holes. After washing, when the details are dried out, you should assemble the carburetor and install it in place.

trimmer, grass, gasoline, assembly

The engine on gasoline can also stall when clogging the fuel filter with the remains of grass and dust. It, like an air filter, must be removed from motorcycles and washed with gasoline. After drying, the filters should be installed in place.

Often in trimmers with a curved bar overheat or the shaft of a mowing head ceases to rotate. This happens when the indigenous bearing is not lubricated or damaged. It is two bushings placed in one another. This part must be smeared or replaced with a new one, if the bushings are broken and the shaft is jammed. To do this, you need to:

To replace the radical bearing, the trimmer head should be removed

To replace or lubricate the root bearing of a trimmer for grass with a flexible shaft (cable), it is necessary to remove the mowing head and casing to protect

To extract the indigenous bearing from the hole of the bar, it is necessary to unscrew the lock screw in advance

To eliminate other breakdowns of a trimmer for grass, including a shaft break or failure of a motor, you will need the help of a professional master who may present a special repair service.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, it will be useful to disassemble it first, and later Collect. This process is not a particularly difficult occupation. For work, a screwdriver with a suitable shape is useful for work.

Parsing the starting node

The start.up mechanism is disassembled in order to establish new details of the incorporation broken in the subsequent sequence:

  • spin a screw with a screwdriver, fixing the pulley with a starter lid;
  • take out a spring and antennae;
  • Remove the pulley neatly (it is necessary to unscrew the head or work with all this, dressing for earlier glasses and gloves);
  • determine why the starting mechanism has broken;
  • If the spring was actually destroyed by one hundred percent, then it is replaced;
  • When the spring exits from the hook, it is installed in the original place, bending the antennae before that (the photo shows the styling process);

After the spring plate is installed inside the groove, carefully make it twisting. To change the spring, you should work intently and carefully: it can, under the influence of the effort caused by the installation of it in place, to break through. Even if you carefully remove the video, then the spring strip flies very rapidly from the coil and can injure the hand with its sharpened edges

Even if you carefully remove the video, then the spring strip flies very rapidly from the coil and can injure the hand with its sharpened edges

To change the spring, you should work intently and carefully: it can, under the influence of the effort caused by the installation of it in place, to break through

Even if you carefully remove the video, then the spring strip flies very rapidly from the coil and can injure the hand with its sharpened edges

Spring tension

After installing the spring, it should be pulled. For this they make subsequent deeds:

  • Remove the handle from the starter cord;
  • Then the rope is inserted into the coil groove;
  • create a stretch of the spring, rotating the coil in the direction of the back of the clockwise (views);
  • make the required number of revolutions indicated in the operating annotation to the used trimmer model for the grass and the corresponding length of the cord used;
  • At the very end, the rope is threaded into the hole created for this, located in the starter cover;
  • put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this by subsequent methods:

  • Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
  • drill holes from the 2nd sides of the groove in the coil, into which stick the sprout hook and fix it with a wire.

Starter assembly

The assembly of the starting node is carried out in a row of steps:

The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;

When making the stated manipulations, you must definitely lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled, the jerking off will begin. Because of this, there is a feeling that the spring has flown away. In order to remove such a defect, it is necessary to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starting node will begin to work without shaken. But such an option is temporary. it is better to repair excellently as a razor as possible.

Do not try to control the brush without attaching the tool case to the suspension. Firstly, the bureau weighs 5 kg, and it is difficult to keep a heavy tool on elongated weapons. Secondly, this method is a certain danger and significantly increases the risk of injury.

The Husqvarna chainsaw system has a special mounting design, which allows you to almost instantly unfasten and unfasten the belts using the device.

Another small drawback of Husqvarna Kustorez is an increased noise level when operating the tool engine, so use headphones or a protective helmet.

Fuel consumption in working mode is about 500 ml. In hour. This means that in an hour you can mow highly overgrown grass with an area of ​​no more than two hundred square meters. From practice, it is known that the usual six hundredths of the country can be mowed by the Googvarn screw for at least four hours.

Husqvarna brush quality surprises even skeptics about the use of gas trimmers. Despite its compact dimensions, the device processes old perennial weeds and young shoots of trees, but in terms of performance, the tool will not compete with self.propelled gasoline braids.

The specialists of the service center often complain about the consumers of garden equipment for home, which make mistakes and turn off the equipment at the stage of assembly and the first launch. Of course, there is an instruction in the package, but either it is written stupidly, or is read after the wrong assembly, when additional details were found or, even worse, a failure occurred. Meanwhile, there is nothing complicated in the assembly of household garden equipment. You just have to be careful. Here is an example of the procedure for assembling gasoline baskets of Stihl FS 130, complementing our instructions with illustrations.

Start the installation by opening the box and checking the assembly of the device. If everything is in place, then we must attach the handle to the rod using a motor, put on a belt, attach a protective cover and cutting elements.

First you need to remove the handle and unscrew the thumb screw, which fixes the upper part of the support without losing the spring.

Insert the handle into the nest and fix it without tightening too much. The final position is adjusted after the final assembly of the bushrase.

Put on the adjusting handle of the device on the handle tube and tighten the fastener. For this, the kit includes a universal key.

All controls of the gasoline brush Stihl FS 130 are located on the handle. This is the lever of the throttle, which is protecting against random turned on, and the shutdown lever for the device with the thumb. In the modification of a bush cutter with a D-shaped handle, the controls are located next to the engine on the rod.

Put a plastic protective cover. If you plan to use only a knife, then for its operation we use part of the case (in the figure it is painted in orange).

If you want to work with the cut line, then put on the plastic “skirt” on the protective cover of the chainsaw and put a knife for cutting a braid fishing line. In some versions of this model, the case may be universal or you can attach two different covers. One for fishing line, and the other for a knife.

When straightening the “skirt” on the case, it is necessary to check the reliability of its fastening. Sometimes it may be necessary to fix this protection with another screw.

Now you need to put a knife to cut off the fishing line for the trimmer and fix it with a screw.

It remains to install the coil, having previously filled its fishing line for the trimmer. The coil is screwed onto the shaft (as in the figure) or is attached with a special nut. Keep in mind that the thread on the shaft usually remains. How to pour a fishing line for a trimmer into a reel, read the instructions.

If you need a knife, then put it instead of a reel. The knife is equipped with a protective cover so that during operation it does not plunge into the ground. After installation, be sure to scroll this cutting element and make sure that there is no reproduction.

Well, the last, the easiest step. Install a metal clamp on the rod, that is, mount for the suspension belt.

After the brush is assembled, put on the shoulder belt or suspension on the belt of the backpack (depending on what is included in the kit) and adjust them in accordance with the pattern. Pour a gasoline mixture, start the engine. And let’s go.

The gas handle is suitable for most Chinese gas trimmers (trimmers). For example, Carver (Carver), Crosser (Crosser), Taiga, Ural, Baikal, Expert, Clover, Atlanta and other lawmakers (trimmers for grass) with an engine volume 33.43 cubic meters. A gas handle for a Chinese gas trimmer for grass (trimmer for grass) Carver (Carver) is reliable and simple to use.

Article: 010049AU manufacturer: Bensorhythm (Bensorhythm)

The incomplete list of structurally similar gas trimmers (trimmers) with an engine volume 33 cm3 and 43 cm3, for which the gas handle is suitable:

Gas trimmers for grass with engine volume 33 cm3: Carver GBC. 033; Carver GBC. 033 S; Piranha BC 330; Icomagteules BF 33; Aiken MC 255/33 L; SD. Master GBC.033; Texas to n.E 33; Texas CG 330 b; Ergomax BC 33 E; Profer 330; Red Star CG 330; Champion T 334; Profi BG330B; Priority 330; Green field GF 330 b; GCB-330 gardener; Unifield 235; Packard Spence PSGT 330; Packard Spence PSGT 331; Garden fishing line for the NTCG330 trimmer; Beezone CG330BF; Redverg RD-GB330; Pegas CG330B; Akita CG330; Resource RBC 330; Profi SS-BC330 and others.

Benzine trimmers for grass with an engine volume of 43 cm3: cutter GBC-043; Charger GBC-043S; Piran BC 430; Icomagteules BF 43; SD-Master GBC-043; Texas BC43; Texas CG430B; Ergomax BC-43E; Profer 430; Red Star CG 430; Champion T 434; Profi BG430B; Priority 430; Green field GF 430 b; GCB-430 gardener; Unifield 245; Packard Spence PSGT 430; Packard Spence PSGT 431; Garden fishing line for the NTCG430 trimmer; Beezone CG430BF; Redverg RD-GB430; PEGAS CG430B; Akita CG430; Resource RBC 430; Profi SS-BC430; TSUNAMI TG 43WS; Hammer MTK43; Practice GTB43; Aiken MC 255 / 43L and others.