Trimmer Gauge How to Fill a Fishing Line

Trimmer Gauge How to Fill a Fishing Line

Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Preliminary preparation

First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
  • electric and gasoline trimmers with a curved rod without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
  • electric and petrol trimmers with the possibility of installing a knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

We carry out winding fishing line

Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task. winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working antenna

The simplest option and a simple sequence of actions:

  1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding. 2. 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse direction of rotation of the spool on the trimmer product. as a rule, on the inner side of the bobbin an arrow indicates which direction the winding is going.
  4. A small section of fishing line is left free to bring it out. it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the bar of the trimmer.

Coil with two working antennae

In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

  • one groove. both antennae are wound together along one groove;
  • two grooves. each antennae is wound on an individual groove.

For both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar. the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly. this operation is not difficult and with some patience will certainly succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism makes winding on its own. from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the spool is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

Video: Trimmer Gauge How to Fill a Fishing Line


The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that you can use this technique in places where a regular lawn mower will simply not be able to get because of its massiveness. It is necessary to understand in more detail what kind of trimmers are, and how to choose the best option for a particular summer cottage.

What is a trimmer?

The basis of this equipment is the following elements:

  • an engine whose main function is the rotation of the cutting head at the end of the rod;
  • directly the head, consisting of a coil on which either a fishing line or a knife can be wound;
  • knives or fishing line rotating at high speed, which are the main cutting part of the device, about how to charge the fishing line into the trimmer, we will go a little further.

An electric apparatus is inferior in power to a gasoline one, so it is ideal for working on a standard plot of land that adjoins a house with an electric energy source. The main positive aspects of this technique are the absence of noise during operation, light weight, ease of operation and, of course, environmental friendliness.

As for gas trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. It is not necessary to use electric energy at all, which has a positive effect on the functionality of such an apparatus. the cutting nozzles can be changed while working with the most diverse weeds of their type.

One of the most common attachments is fishing line, so you should dwell on this element in more detail.

Types of fishing line for trimmers

As a rule, the separation of fishing line is based on a different diameter of the samples, which can vary from 1.2 to 4 mm. The most commonly used material is with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

You may also like

  • The trimmer is the most common unit used for cutting grass and cutting small bushes. This unit is notable for its ease of maintenance, simple operation during operation, and even women can cope with i...
  • Technical characteristics of the OSB board and harmfulness. for beginner buildersOriented particle board has appeared on the construction market recently. it replaced the previously popular chipboard....
  • One of the important chainsaw systems, work without which is impossible, is the system of forced lubrication of the chainsaw chains. It’s no secret that at the time of the saw’s operation, the chain a...
  • Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that t...
  • Lush vegetation between houses in a residential quarter or cottage can clutter paths and areas under fences. Unlike a neat lawn, tall grass looks ugly. At enterprises, uncut areas of greenery create a...
  • Trimmer, or lawn mowing. a tool that can not be done in the household. At the same time, its reliability, efficiency and long service life depend on many factors. For example, fuel quality. This means...

Here there is one main rule: the more power the device has, the thicker the fishing line should be.

This element can also differ in the type of its section. So, it can have a round (suitable for cutting simple grass) or square (for mowing a soft green cover) shape, sharp edges (tall grass) or it can be equipped with notches that are ideal for thin-diameter grass.

Do not forget that with the help of a fishing line it is allowed to mow exclusively grass, and for other, rougher vegetation, knives must be used.

Next, you should consider in more detail the process of how to insert the fishing line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

How to fill the line in the trimmer?

Any machine for mowing vegetation is necessarily equipped with a coil, which, in turn, may already differ for different models with a filing system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to fill the line into the trimmer.

In order to fill the fishing line into the trimmer, it is necessary to take at least 5 meters of material, which is then folded in half. The center of the cutting element must be inserted in a place specially designed for this, and then, using the visual tips on the reel that indicate the direction, the cutting device should be wound. At the end of all work, the cover, of course, will need to be tightened.

Fishing line adjustment

One of the main rules when replacing and adjusting equipment is that any manipulations with the mechanism should be carried out exclusively with the engine turned off and the plug of the device disconnected from the network.

Perhaps these tips will tell you how to fill the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the type of cutting material necessary for the type and, of course, determine the category of the most used trimmer.

  • What types of woods are
  • How to remove or refill a fishing line in a trimmer

Since we considered the choice of the trimmer in the previous article, today we will tell you how to properly trim the trimmer with a fishing line, and which is better to choose based on the working conditions.

After you bought a trimmer and began to use it actively, sooner or later the question will arise about replacing the fishing line, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

What types of woods are

The most common type of fishing line, which is suitable for almost all types of coils. round cord. This is an ordinary fishing line suitable for mowing juicy grass, but mowing dead wood with it will be much more difficult, and even more so it can not cope with the bush.

As a rule, the diameter by which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or square, this option is more suitable for mowing dry grass just due to the existing sharp edges, but its disadvantage is more wear and tear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but they are used only on lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs into which segments are inserted. The disadvantage of this product is its fragility.

Most often in gas trimmers with an engine power of more than 1.5 hp apply cords with a metal cable inside.

This thread is ideal for mowing dry grass and small bushes. The presence of a core positively affects the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to remove or refill a fishing line in a trimmer

It takes about 10-15 minutes to wind the line. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line.

Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. The photo below shows some examples of different coils for trimmers.

The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

The principle of the correct winding of the fishing line is similar in all of the above cases, so for example, consider the standard version with two antennae.

To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and take out the reel, on which the fishing line is directly wound.

Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

If you have doubts or it’s not entirely clear how to charge the fishing line to the trimmer, we recommend watching the video: how to wind the fishing line into the lawn mowing properly.

In this video, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.