Unscrew the head of the trimmer for the grass Stihl FSE. Stihl fs-38 mower coil of a new model, installation of fishing line

trimmer for grass gasoline stihl does not spin the head

Carburetor adjustment is necessary in the following cases:

  • The new engine was running out (4-5 liters of fuel mixture were used);
  • The composition of the fuel has changed (brand of oil and gasoline);
  • The weather changed (it became hot, cold);
  • Air vacuum has changed (concerns mountainous areas);
  • after long.term storage;
  • the load on the engine has increased (after changing the tool and t.D.);
  • Due to the vibration, the adjustment screws spontaneously unscrewed;
  • Fuel consumption has increased, the carburetor shimmers the fuel;
  • Flapse quickly appears on the electrodes of the candle (while the fuel mixture is prepared correctly);
  • The motor starts and immediately stalls or is poorly gaining momentum;
  • Gasoline does not enter the cylinder;
  • A large amount of exhaust gases.

Reasons why the lawn mower does not develop momentum

There are five main reasons why the trimmer for STIHL grass does not develop turns:

Low quality fuel use

Benzotrimmer does not gain momentum in case of low quality fuel. He may stall or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for problems with the combustion chamber.

In the presence of sediment, plaque formed on the candles, the old fuel is drained and flooded another, high.quality.

It must be remembered that a trimmer for grass or a lawn mower should be refueling good quality gasoline and those fuel brands that the manufacturer indicated in the technical passport of the device.

Note! Candles should be thoroughly cleaned of plaque, and only after that place again in the combustion chamber of fuel.

Air or fuel filter pollution

There is a lawn mower does not gain speed, the reasons may be polluted by the filter element: air or fuel.

When blocking the air filter, there is a lack of oxygen in the combustion chamber, so the fuel is not fully produced, which prevents the desired speed and power.

To check if the cause is really in the air filter, you need to remove it and turn it on. If the lawn mower still does not gain momentum, the reasons are not in it. So you should check the fuel filter element. Everything is similar here, only gasoline acts as oxygen. If this filter is damaged, there will be a lack of fuel, which inhibits the development of revolutions.

In one and another case, the output is simple: you just need to replace the filter. If there is a spare, install it, if not, to purchase in any specialized store, is inexpensive.

Problems with ignition candles

When a benzotrimer is used often, you need to monitor the state. This part is susceptible to wear, so they need to be regularly examined: is there a Nagar on them.

You can solve the problem in two ways: clean the old candle from Gary or purchase a new one.

In the first case, you need to unscrew and swing with sandpaper, dry. The distance between the electrodes should be 1 mm. Trimmer for grass is collected and advanced.

In the absence of a spark between the electrodes, it is worth inspecting the quality of the connections of all the elements of the circuit. If in this case everything is fine, then 100% you need to change the candles.

Replacing them is easy and inexpensive. From the tools will be needed a key, supervisor.

Important! With frequent appearance of soot on the candlelights, it is worth looking for a reason a little deeper

Candles should be carefully cleaned of plaque

Problems with the engine

Engine problems. already more serious. There are several options for a malfunction:

In the case of the problem of the carburetor, you should first pay attention to the condition of the cable. It can be weakened, which led to a problem

A simple adjustment of the cable is required here.

If this did not help, then you need to check the use parameters. These operating standards can be found in the technical passport of the device. Sometimes it’s enough to disassemble the device: to wash and collect and assemble.

note! The solution to the problem with the carburetor may be the purchase of a new element or by contacting the service for professional services. The trimmer drive is subjected to a full check only if the manipulations with the carburetor were not given the proper result

The trimmer drive is subjected to a full check only if the manipulations with the carburetor were not given the proper result.

FLOOK DISCOUNSE

The lack of fuel circulation in the system can also be the reason why the device does not gain momentum. There are several options for why this is happening:

You can eliminate problems yourself. For this you need:

  • remove blockages from the gasoline pump;
  • update hoses, pipes for fuel circulation;
  • Clean the muffler and mesh on it;
  • Reinching a new catalyst.

Do not worry when such problems arise. This does not mean at all that the unit of poor quality. If the Patriot trimmer does not gain momentum, it can be repaired with your own hands without contacting the service.

HOW TO: Start a Stihl FS 38 Grass Trimmer

Master class: weaving from wire pendant “Tree of life

Spring fully entered into its legal rights and we considered that today’s master class on weaving the wonderful pendant “Tree of Life” from the wire would have to be just in the topic. After all, what is spring, if not a revival of life after a long sleep? The ancients unsusually imagined the annual cycle of the seasons precisely as a consistent movement of nature from birth to death, and spring quite naturally symbolized its birth.

The very symbol of the “Tree of Life” is found in almost all world cultures.

Be that as it may, the image of the tree has a unambiguously positive meaning, symbolizing the unity of nature and the eternal cycle of life.

In our master class, we will use the Celtic version of this symbol, which in the modern world is most widely used and is often used in the production of decorative products, jewelry and cult attributes.

We wish you a pleasant and, most importantly, successful creativity!

Sketches “Tree of Life”, they are quite easy to find on the Internet.

The first way

The prepared segment (in this case, it is 4 meters) is bent approximately in half-one segment should be 15-20 cm longer, and inserted into a special gap located on the dividing partition.

A fishing line for a trimmer is wound in a particular direction. This is done in an interference, the fishing line for the trimmer is neatly distributed. In this case, you need to wind the segment, which is longer into the section, which is closer to the button.

There are designs in which there is no division of the coil into two sections. This does not change anything, the fishing line for the trimmer is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first should end the segment that is located at the bottom of the coil, t.e. closer to the fixing holes.

This tip is placed in the corresponding diameter hole. Trimmer fishing line is reliably fixed.

A long segment wraps another half turn. There it is similarly fixed. At the same time, the segment crosses another coil section.

A long segment wraps another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously recorded in the holes of the coil of the fishing. This is easily determined by the characteristic sound (click).

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass.

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass

The replacement of the fishing line was successfully made. In this case, you need to install it back on a trimmer for grass and you can proceed to the span of grass.

It should be repeated, you do not need to remove the spool from the trimmer for the grass. this was done to clarify the process of replacing fishing line. You can disassemble the rogue in place, wind it up and put it back.

The tips so that they do not beat the trimmer casing for the grass, you can and should be cut.

How to refuel a fishing line for a trimmer to a trimmer coil for grass

To replace the fishing line in the trimmer, cut a piece of material of the desired size, folding it in half. One of the halves should be 5-10 cm longer than the second.

In order to correctly wind the fishing line for a trimmer to the coil, the middle of the thread, folded by a loop, you need to place in the groove of the central partition. One half of the forest is tightly wound on the upper part of the part, the second. on the lower. A longer part is wound on the bottom. Winding is carried out in the direction opposite to the direction of rotation of the head. An arrow should be drawn on the lid or side of the head. it shows the direction of rotation. It is necessary to wrap the forest in the reverse arrow direction. Do the job carefully, tightly pressing the turn to the turn.

Insert the remaining ends with a length of 10-15 cm into the slots on the upper side of the coil, this will fix them. The coil is not unwound with fixed ends.

If you do not have a fishing line of the desired length, you can wind the forest with more than one piece, but two. In this case, bend the end of the forest with hook and insert it into the slot of the central partition of the bobbin. Do the same with the second piece. Now wrap first a piece first, and then the other to your half of the coil against its direction of rotation.

To refuel a fishing line for a trimmer in a trimmer for grass, insert its ends into the holes of the mowing head and pull them out. Plant the coil on the axis and push down so that it sat in its place, and again pull the ends of the cutting thread to pull them out the entire length.

The ends brought out should almost reach the protective casing. Cut the excess. To do this, you can use the steel plate installed on the casing, which plays the role of a knife and automatically cuts a fishing line for a trimmer of excessive length when promoting the head.

Bobina closes with a protective lid. Put it in place and press it down to the click that the latch will be published by falling into the grooves. Always check whether the cover has stood on the trimmer for the grass and whether the latches snapped, otherwise it may jump off during operation. In this case, the reel will throw the reel force.

Do not try to wrap the material as much as possible. in this case, the coil may not fall into place and there will be problems with the installation and fixation of the lid. It is better if the coil is filled with wood so that it does not go beyond the dimensions of the details.

In addition to mechanical braids with two blades, there are also models with one. Their differences are that the cutting thread is displayed only on one side. The coil in such versions of the braid may not have a central partition, instead of it, a slot in the lower side is used to install a non.working end of the thread, there is also a slot for fixing the working end in the upper.

With a replaced forest, you can start work. Do not mow thick weeds and bush branches. this is not work for braids for grass. In order to avoid injuries and a break in the forest, make sure that stones and branches do not fall under the braid.

To download the lawn of one refueling coil with a reinforced fishing line is enough for an area of ​​400-600 m2.

After the cutting thread as a result of the work is worn out, turn off the braid and remove the lid on the mowing head. Pull out from the slot of the forest, stretching it to the desired length, and insert it again in the slot. The amount of material wound on the coil is enough for 5-10 cycles of work depending on the model of the device. When you install the lid in place, carefully look at whether the grooves were clogged where the latches are inserted, if they are clogged, then carefully clean them.

When the fishing line for the trimmer is worn out, you need to disassemble the braid head again, pull out the coil and wind up the work fishing line for the trimmer again.

How to change a fishing line for a trimmer Stihl

The only difference from the method is no different from the method. two wound segments of fishing line, instead of one.

There are two special fixing nests on the coil (see drawing above).

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special order

The winding needs to be carried out in the following order: first the lower fishing line for the trimmer, t.e. that which is closer to the fixing holes at the bottom of the coil, and only then the upper one, t.e. the one that will overlap the lower section.

The tips are made in the holes of the corps of the rogue trimmer for the grass. They are pulled to a click, which means that the fishing line for the trimmer has left the latch.

The tips are torn into the holes of the corps of the rogue trimmer for the grass

The coil is fastened into the case. The fishing line for the trimmer in the rogue is replaced.

Replacing fishing line in trimmer: 2 simple ways

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

The first way

The prepared segment (in this case, it is 4 meters) is bent approximately in half-one segment should be 15-20 cm longer, and inserted into a special gap located on the dividing partition.

A fishing line for a trimmer is wound in a particular direction. This is done in an interference, the fishing line for the trimmer is neatly distributed. In this case, you need to wind the segment, which is longer into the section, which is closer to the button.

There are designs in which there is no division of the coil into two sections. This does not change anything, the fishing line for the trimmer is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first should end the segment that is located at the bottom of the coil, t.e. closer to the fixing holes.

This tip is placed in the corresponding diameter hole. Trimmer fishing line is reliably fixed.

A long segment wraps another half turn. There it is similarly fixed. At the same time, the segment crosses another coil section.

A long segment wraps another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer’s corps of the grass

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously recorded in the holes of the coil of the fishing. This is easily determined by the characteristic sound (click).

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass.

The coil with the button is snapped in the corps of the trimmer’s trammer for the grass

The replacement of the fishing line was successfully made. In this case, you need to install it back on a trimmer for grass and you can proceed to the span of grass.

It should be repeated, you do not need to remove the spool from the trimmer for the grass. this was done to clarify the process of replacing fishing line. You can disassemble the rogue in place, wind it up and put it back.

The tips so that they do not beat the trimmer casing for the grass, you can and should be cut.

Preparation for replacement

For clarity, a mowing head was removed from the motorcycles (Spool). To replace the fishing line you do not need to remove it, everything is done in place. It doesn’t take much time.

We disassemble the rogue of the trimmer for the grass-it holds on the clan locks. Remove the lid, pressing on the latches. If you do not have enough effort with your hands, then use the screwdriver.

The principle of action is as follows. By clicking on the button, the coil presses on the spring and leaves the fixing grooves in the lid of the spray. Holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When the button is released, the housing spring returns the coil to the original fixed state.

Below on the coil there are several holes for a different diameter of the forest. For different manufacturers of trimmers, they may differ. In some cases (as here) they are signed, in others there is no.

These holes are needed to fix the fishing line when replacing it. After winding on the labina of fishing line, the ends of the latter are inserted into them. This is necessary so that the forest does not unwind at the time the coil is installed in the trimmer body for grass. In other words, it facilitates the replacement of fishing line.

There are models without specifying the diameter of the consumable. Then, in order to find out what maximum forest diameter can be used, it is tried on by the openings of the fishing line out of the trimmer’s corps of the grass (see. Figure below).

The coil has two sections for the fishing line separated by a partition. They may not be. They are needed only to distinguish and facilitate the winding of the consumer.

First determined with the required Lessa length. The latter is wound into one of the sections of the coil so that it does not go beyond it. In this case, 3 mm was wound, the length turned out about 2 meters. T.e. For two sections, you will need a segment of 4 meters. this is for the 1st method. For the second method you need two segments of 2 meters.

unscrew, head, trimmer, grass

Now you need to figure out which way you need to wind it. To do this, many manufacturers of trimmers on the coils apply special designations such as in the figure from below.

If there were no such designations, then you need to pay attention to the spool body. There is a must.be arrow that indicates the movement of the mowing head. The fishing line for the trimmer is wound in the opposite direction.

How to wind a fishing line for a trimmer to a mowing head of a trimmer for grass or motorcycle

Replacing fishing line in trimmer: 2 simple ways

Feedback with our readers is very important for us. Leave your rating in the Комментарии и мнения владельцев with the argument of your choice. Your opinion will be useful to other users.

STIHL Motokos, refueling the string in the Autocut 25 2 2

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the prerequisites are subsequent.

Option 1. it came out snacking, t.e. Squeezing the cord between the turns. This non.bond usually occurs if the user wound a fishing line for a trimmer to the coil unevenly, with a crossbreed of turns, or wound it with the missing tension. In the latter case, when the mowing head is rotated at huge revolutions under the influence of centrifugal force, the cord begins to delay, and as a result you are inter.trustee pouring the fishing line. To eliminate the difficulty, you will have to disassemble the coil on the trimmer and rewind the cord correctly, in other words, even coils with good tension.

How to replace a fishing line for a trimmer on a STIHL motorcycle

About a year ago, the author of these lines bought the STIHL Motokos (Stihl, as they say in the common people) FS 38.

The fishing line that was in the herbs was purchased for about a year and was enough, the last remnants were torn out when a dry tree branch was not seen in the grass. This is not the point.

The fishing line for the trimmer for replacement was also bought, along with a motorcycle (trimmer). But when the question arose of how to replace it, it caused difficulties. Searches on the Internet on request how to replace a fishing line for a trimmer STIHL did not lead to an instant result. precisely, the author of these lines came across a question about replacing the fishing line, asked by the user a specialist and answer: it is impossible to explain this, contact the dealer, he will show.

Well, he went to the dealer, the dealer showed, and he (the author of this entry), having arrived home, pulled out a fishing line for a trimmer and inserted it in front of the camera again. To yourself, if you need to remember, and show others. Those who are worried about the beauty of the house or garden.

So, see how to replace a fishing line for a trimmer on a STIHL motorcycle.

Update

After publishing the video, a method was found even easier, and a new video was shot. At the end of the video, bonus advice How to quickly adjust the length of the fishing line.

How to replace a fishing line for a trimmer Stihl trimmer

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

Advice! To understand which way to wrap the thread, you should look at the corps of the spool. usually marks are made on it indicating the direction of movement of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

What is needed to replace the cord

With regular use of a trimmer for grass for begging grass, the discs are blunting, but they can be sharpened and continued to operate. The fishing line for a trimmer in the coil has the ability to end, so there is a need for refueling a new one, for which you need to determine the type of head and prepare the cord of the required thickness and length.

So, the mowing head is a cylindrical body in which a bastard is placed with a fishing line. Such a part is present both on electrimmers and on gasoline braids of any brands, whether it be Bosch, Makita, Stihl or other brand. There are three types of heads depending on the method of refueling and feeding the fishing line.

  • The principle of operation of the heads of the automatic group is that they independently serve a fishing line for a trimmer, when a mowing reduces the speed of the motor. Such designs are convenient when working in large areas, but they have a shortage. a large cord consumption.
  • The heads of the semi.automatic group are easy to operate. automatic fishing is performed at maximum engine speeds. To remove the cord lock, you need to carefully tap on the ground with the tool, after which the unlocked thread extends from the coil. The cut to the required length is made with a knife fixed on the protective casing.
  • Trammers for grass with manual supply of the cord must first be turned off, and then independently pull out the fishing line for the trimmer.

On a note! The most convenient and optimal in price are semi.automatic coils with the cord.

Coils for electric and gasoline braids can be with one or two tastes of fishing line. The former are used to trim low herbal shoots, the latter. for beveling tall grass and small shrubs.

Solving possible problems with fishing line

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. it is enough to correctly season the fishing line for a trimmer from the user. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside. It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

The coil does not spin

The reasons why the coil does not spin are similar to the lack of fishing line. This is the wrong or uneven winding of the string, its sticking, as well as the short ends of the cord, emerging from the holes.

Preparation for the replacement of fishing line

Before replacing the fishing line, you need to pull out, and then disassemble the head. It usually includes a casing, a spring (on some models), a bobbin with a fishing line, a lid. It is necessary to turn off the electric trimmer for the grass (or drown out gasoline) from the network, and then proceed to remove the coil. It can be recorded in two different ways: in the first case, it is necessary to completely disassemble the head, and in the second. just remove the gearbox from the shaft, to which it is attached.

  • Find the latches on both sides, press and remove the lid to open the internal device of the head;
  • A bobbin is located under the lid, it must be carefully pulled out of the case (sometimes a spring is hidden under it, it should also be carefully removed to the side so as not to lose);
  • After removing the spool, it becomes noticeable in the center of the case with a fixing bolt (or screw), which must be unscrewed in a direction opposite to the clockwise movement;
  • After removing the fasteners, it is necessary to hold the body with a swaying movement to remove the coil from the gear shaft.

The second method involves the following actions. Coil head is worn on the gear shaft. To disconnect it, you need to lock this shaft. Typically, in braids, for example, the brand “Champion” or “Stihl”, for this a hole is made into which a nail, rod or screwdriver is inserted. After fixing the shaft in a fixed position, you need to, holding the body, start rotating the head clockwise, since the thread on the shaft is usually applied to the left.

Now that the head is removed and dismantled, it is necessary to determine what thickness the cord should be. You can find out the suitable diameter for your trimmer for the grass by looking at the user’s guide or on the squash itself, it usually indicates such information. Another way is to insert the thread into the hole from which it is served. If the Sruna is without difficulty, it can be used to work.

How to replace a fishing line for a trimmer correctly

The most worn.out element in the design of a trimmer for grass hairline. Therefore, it is important to know how to choose and wind it. All details in the article.

Since we examined the choice of a trimmer for grass in a previous article, today we will tell you how to cut a trimmer for grass with a braid fishing line of hair growth, and which of them is best chosen depending on working conditions.

After you purchased a trimmer for the grass and began to actively use it, sooner or later the question will arise about replacing the braid fishing line of hair, since this is the most worn out element of the tool, the intensive use of a trimmer for grass will lead to frequent replacement of consumables.

What are the types of forests

The most common type of mowing fishing line, which is suitable for almost all types of coils, is a round cord. This is an ordinary haircut that is suitable for mowing juicy grass, but it will be much more difficult to mow it with a dead tree, and even more so since it cannot cope with the bush.

As a rule, the diameter in which you can mow young grass does not exceed 1.6 mm. The thicker the thread, the more rude the grass will overcome.

There are hairs with sharp edges in the form of a star or square, this option is more suitable for mowing dry grass precisely because of the existing sharp edges, but its deficiency is more worn out and inferior to the strength of a round cord.

There are aerodynamics with improved aerodynamics with characteristic dents, scales and excavations, such a product produces less noise, but they are used only on braids, since the output of such a thread from the coil is difficult, most often it is used with disks in which segments are inserted. The disadvantage of this product is its fragility.

because win a fishing line for a trimmer on a trimmer head or braid

The video shows in detail how to cope with the hair to the coil trimmer for grass or motorcycle. Clutching hair mow.

Replacing the cutting element with a motorcycle

How to independently wind the cutting cord to the coil of braids (trimmer for grass)

Most often in gas trimmers with an engine power of more than 1.5 liters.With. use cords with a metal cable inside. This thread is ideal for mowing dry grass and small shrubs.

unscrew, head, trimmer, grass

The presence of a core has a positive effect on the wear resistance of this material. The disadvantage of such a cord is its price, which is much higher than that of these opponents.

How to fill a trimmer coil

It takes about 10-15 minutes to wind the braid. What is a trimmer reel? Plastic case with a cassette inside, which has a special hook for convenient winding of fishing line.

Almost all trimmer coils have a similar attachment principle, this is a central spiral button, when pressed on which you can stretch the hair of the desired length.

The photo below shows some examples of various coils of a trimmer for grass.

The studs of the trimmer for grass, the engine of which is located near the ground, have different fasteners to the rotation axis, they have two buttons on the coil located on the sides of the press, otherwise the replacement of the thread is no different from the others. cartridges.

The principle of proper hair winding is the same for everyone the above Cases, for example, consider the standard version with two antennas.

To remove the coil with the help of the wire, you need to unscrew the screw located in the center, but keep in mind that the thread remains there, so you need to turn it clockwise, this is specially so that it does not open under the influence of centrifugal.

Then, using a screwdriver, disassemble the head and remove the coil, which is directly wound on a fishing line for a trimmer of hair growth. Having measured the required length and folding in half, it is necessary to pour the fiber into the coil, removing, in the end, its ends are opposite each other (there are special slots for fastening).

Then collect the head in the reverse order, tie the ends of the cord in two corresponding holes.

If you have doubts or it is not clear how to download a trimmer for grass using a trimmer for grass, we recommend watching a video on how to wrap a comb correctly. In this video, the instructor will open the head of a trimmer for grass in detail, in stages, will measure the required amount of cutting element, usually two to four meters, and demonstrate installation and installation on the trimmer.

How to wind a trimmer for grass on a trimmer for grass? House and life. Yandex.Test

The coil of the trimmer for the grass is located in the head of the mowing, which consists of a spring, coil and two lids.

First of all, it is necessary to disassemble and remove the head of the trimmer for the grass. To do this, move the locks to the end of the case and turn clockwise.

To open the mowing head, press the side latches; If you cannot do it manually, you can use the screwdriver. Remove the coil.

Look at the insides of digital markers to make the right choice for a trimmer for grass, which is especially suitable for your trimmer for grass. These numbers indicate the necessary diameter of the wire in millimeters.

If you have not found such information, then the maximum diameter can be determined by taking a fishing line for a trimmer and passing it through a hollow pit. The thread should flow freely forward and backward.

How to wrap the wire on a three.dimensional coil. one way

Wipe about 4 meters of wire wire. To determine the exact amount of the necessary material, wrap the roll from the roll to the coil; The final result should not exceed the diameter of the coil and rise at the edges.

For convenience, fold the thread in half, make one end 10-15 cm longer than the other.

There is a separation side on the coil, which takes place in the center. It has a cavity into which you want to insert a fishing line for a trimmer. To do this, squeeze the place where the thread is bent and tighten the loop in this cavity.

Important. It is necessary to clearly determine how to wrap the fishing line for the trimmer, find the inscription “Fishing line for the trimmer of the wind” on the coil, next to it there is an arrow indicating the direction of winding. If there is no such arrow on the coil, find the arrow on the mowing housing; This should be wound in the opposite direction.

Gently wrap the fishing line for a trimmer on the coil, pulling the thread as far as possible.

At the end of the work, take a shorter end and insert it into the blade on the coil body corresponding to the diameter of your mowing hair fishing line. In this work, the thread was lowered into a blade with a mark of 3.3 mm.

Do the same with another end, but insert it into the blade opposite the previous. Fix two ends, leave the allowance by 5-10 cm, cut the rest. Passes are necessary so that when inserting the coil into the head, the thread does not unwind.

How to wrap the wire on a three.dimensional coil. The second path

The winding methods are different. In the second method, two.section wires are used separately. At the end of the thread, bend the brackets as shown in the photo and insert them into the mounting hole. Wrap two coil blades as follows.

If you have one blade coil, find a hole inside to fix a fishing line for a trimmer of hair growth. Insert the wire in one of the methods described above. Then cross it to the drum in the opposite direction of the coil of the trimmer for the grass. Leave a small piece of thread and collect the head for the mowing.

When you start working as a trimmer, cut the sharp part of the hair with a sharp blade to cut yourself.

To avoid too frequent changes in the spit line when it is constant stop, try not to touch the equipment with solid items while using.

How to remove the head from a trimmer for STIHL grass

One of the common devices designed for haircuts of grass is a trimmer for grass. It is very easy to work and maintained. That is why it became popular among the population. Its significant advantage is small weight. Even a child can cope with such equipment.

What it is?

A trimmer for grass consists of a cutting element, a bar, an engine and a handle with a control mechanism. It is designed to cut grass in garden areas, as well as to create the perfect lawn. Due to its compactness, the device performs the necessary work in those places where the lawn mower cannot get. In addition to grass, a trimmer for grass is designed to mow branches of trees and shrubs, as well as creating flower beds. Such equipment is not always used for the lawn, since the length of the grass will have different heights.

Specifications

The main technical characteristics of the trimmer for grass are:

  • power;
  • Equipment weight;
  • type of power (from the network or using the battery);
  • engine location (above or below);
  • type of cutting element;
  • Type of bar.

All this needs to be taken into account, buy a particular device.

How to choose the right?

Before buying this equipment, you need to understand for what purposes it will be used. How to replace the head of a trimmer repair for STIHL grass up to 20% of the income of poor debtors from. For a large section with a flat lawn, it is better to purchase a light model with slight power. If you need to improve the summer cottage, then you need to choose the model more powerful.

Cutting tool

So that the haircut process takes place easily, it is necessary to choose the right cutting element.

Its role often acts as an ordinary trimmer fishing line for a trimmer or knife. When choosing one of the species, it is worth evaluating the type of vegetation. The most wear.long element in the design of a trimmer for grass with shrubs. Like a head and. In accordance with these data, a cord is selected, a knife of a certain form. Rotor lawnies how to remove the coil from a trimmer for the grass Makita UM3830. 26.06.2013. An important element is the head for a trimmer for grass. We will consider its varieties below.

Mowing head for a trimmer for grass

It is a special assembled coil, inside which the cord is located. Its dimensions can be diverse. On the inside of the spool should be wrap a cord 15 meters long. Its ends are pulled out to a certain distance to perform work. When meeting with a solid subject, it is destroyed. A mowing head for a trimmer for grass can have a different design. It all depends on the type of device. They differ not only by the design, but also. Watch how to replace the head on a motorcycle chamber repair for STIHL grass with STIH. There is also a universal head for a trimmer for a universal grass, which is suitable for different equipment. This became possible due to special adapters.

The head for a trimmer for grass is classified according to the method of feeding fishing line:

  • Manual. In this case, the name speaks for itself, that is, the supply of fishing line is mechanically. To make the cord even longer, it is necessary to stop the work of the trimmer for the grass and manually stretch the ends.
  • Semi.automatic. How to remove the head from a trimmer for grass and that the thread cut on the when on the coil. How to replace, remove how to replace the head of a trimmer for grass with a repair of a trimmer for STIHL grass. If you want to replace the cord, you need the head for a trimmer for grass touches the ground. In this case, a special button is pressed and the anchor mechanism is opened. Next, the cord lengthening due to centrifugal. The main feature is that the procedure occurs when the trimmer is included.
  • Automatic. To extend the cord, reduce engine speed. Further, with an increase in them, the fishing line for the trimmer is automatically supplied.

STIHL FS 55. Change of coil of motorcycles to a knife

How to install a 2-blade knife on the motorcycle tank STIHL FS 55. Video Instruction how to change the braids of benz.

Repair trimmer for STIHL grass with STIHL FS 38

During the operation of the stihl, the cutting head sometimes breaks, it happens that a cable is torn.Repair.

From all of the above, it follows that a hand.headed braid for a trimmer for grass is uncomfortable. That is why you should choose an automatic type. However, such a head for a trimmer for grass is not popular with users, since during work a large number of fishing line is consumed. Therefore, the optimal type is semi.automatic.

Classification according to the method of refueling

The head for a trimmer for grass can have several ways to refuel the fishing line:

  • Quickly charged. The new cord is wound without analysis of the coil, that is, you do not need to remove it from the device. The end of the new element is touched into the coil and then wound a certain number of times. Upon reaching a specific value, the cord is cut off. The head with a fishing line for a trimmer for grass of this type is produced by Shindaiwa and Speed-Freed.
  • Collapsible. Here the name itself speaks for itself. To replace the new cord, it is necessary to remove the coil from the equipment, then unwind the old fishing line for the trimmer and wind up the new.

Design features

It should be noted that the cutting head for a trimmer for grass contains special arrows. They allow you to perform rotational coil movements in different directions. If there is a need to wind the fishing line for the trimmer towards rotation of the shaft, it turns into a specific position. How to remove a coil from a trimmer for grass, disassemble the braid head. Before as. How to replace, remove the mowing head of an electric trimmer for Black grass how to disassemble a coil. A large number of wound cord threaten equipment breakdown. Two arrows are contained only on imported models. Now the heads are presented on the market with one arrow.

If the cord is not wound after the semi.automatic head, then its previous winding is incorrect. That is, after the head for a trimmer for the grass was installed, the user did not pull the ends of the fishing line from the grooves. Another unpleasant moment in the beard of grass may be sintering the coil turns. Why is it happening? This happens when there is a cord with a solid subject. At the same time, it brakes sharply and, with the subsequent movement, the fishing line for the trimmer begins to go inside the device. Thus, it gets on the rogue and sticks together. Because of this, the employee has to take a break and correct the situation. However, this can be avoided. Before installing the coil, it is necessary to treat the fishing line for the trimmer with a special silicone substance.

How to remove a mowing head from a trimmer for STIHL grass

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of ​​how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wrap a fishing line for a trimmer to a trimmer coil for the grass, how to season a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The most ordinary option and a light sequence of actions:

  • The dimensions of the bobbin and the length of the unique factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the squeezer.located squeling fixing technological hole.
  • The fishing line for the trimmer is wound on the drum in reviting the spilles on the trimmer product direction. usually, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • The small section of the fishing line is left free to withdraw it out. it is fixed in the special side on the inside of the bobbin created to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Automatic winding of the fishing line on the reel

There is a type of coils, in which the automatic mechanism performs winding without the help of others. it is quite only to correctly season the fishing line for the trimmer from the user. How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction. How to remove a coil from a trimmer for grass? How to wind a fishing line for a trimmer in in order to refuel a fishing line for a trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of ​​how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

How to wind a fishing line for a trimmer to a trimmer coil for grass

Trimmer for grass is an excellent solution for those who have a large garden or lawn near the house, which must be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, there will be a need to replace certain elements, and this will have to learn.

How to do it? To replace the main cutting element, first you must choose the right it. In principle, in the operating manual for motorcycles, the diameter of the thread should be used in it.

When you purchased the necessary cutting element, try installing it correctly. It should be noted that on the Internet there is a huge number of videos that will help you figure out how to correct the fishing line for the trimmer to the coil of the trimmer for the grass.

How to change a fishing line for a trimmer on a trimmer

Below we have brought step.by.step instructions for replacing a thread of a trimmer for grass.

The first thing to do is disconnect the tool from the network and turn off the engine. Then it is necessary to remove the head of the trimmer for the grass. This can be done using a simple screwdriver lowering it into the gearbox hole to exclude the turn of the shaft. And then just unscrew

Trimmer coil device for grass

Cassyle heads for trimmers come in different designs. both simple and complex. The figure below shows a semi.automatic trimmer head from the Husqvarna motorcycle (Husqvarna).

This type of head is present in the configuration of most benzocosyles and electrimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the braid head is quite simple. It includes the following details:

  • the base of the mowing head;
  • button for semi.automatic supply of the cord;
  • Spulk (coil), into which a fishing line for a trimmer is refuel;
  • spring;
  • eyes. through them a fishing line for a trimmer goes outside;
  • trimmer head cover;
  • Trimmer fishing line (cord).

There are also simpler trimmer heads shown in the next photo.

All these nozzles do not allow you to change the length of the fishing line in semi.automatic mode (after pressing the button). In the case of a break in the cord, you have to stop the mower and change it manually.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

FIX 95% OF WEED EATER HEADS THAT STOPPED SPINNING!

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

  • In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
  • But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
  • Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Step.by.step instructions for winding a trimmer for grass and a bush cutter

In order not to make a mistake in choosing a suitable fishing line for your tool, first disassemble the head and look at the side wall of the coil. This information is usually provided in the form of a hint that will not allow you to make a mistake when using the appropriate equipment.

If the coil indicates information about which fishing line can be filled out, this information can be indicated in the instructions. Having decided on the thickness or diameter of the latch, it remains to figure out how to charge it. This can be done in two ways, but not all of them are applicable. We will consider both methods in detail, and depending on which models of mowers and trimmers you use, you will determine which option is suitable.

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success: