What Oil Can I Pour Into A Chainsaw
Chainsaw oil. Which is better to use?
Almost all owners of private houses, with rare exceptions, of course a chainsaw. The tool you need, convenient, almost indispensable. In fact, there is a chain saw driven by a two-stroke gasoline engine. The fact that special oils are used to lubricate two-stroke gasoline engines has long been clear to everyone. In that case, neglect the instruction, then the operation of the chainsaw can be short-lived. Let’s consider what features oil for a chainsaw does not have which to use.
Preparing a fuel mixture for a chainsaw
Representatives of companies producing gasoline tools say they do not have information on how their chainsaws work with foreign oils. With the use of the original product, they guarantee serviceable not long work. This does not mean that the tool will definitely fail if the wrong oil was used to prepare the fuel mixture. It is likely that the chainsaw will work at a good level. However, there is a chance to get a refusal of a warranty for free repair if it is established that an oil other than recommended was used.
The ratio of gasoline and oil for chainsaws
To obtain information on what ratio to prepare the mixture is not what to use oil for chainsaws, you should study the instructions. For any equipment that uses two-stroke gasoline engines, the correct proportion is indicated not in the unit’s instructions, on containers with oil. When using the original product, as a rule, the ratio is 1:50. If you have to prepare the fuel mixture using non-native oil, the proportion is changed to 1:40. Simple arithmetic calculations show that for a liter of gasoline you need twenty “cubes” of original lubricant or twenty-five cm three. products from other companies.
As a guide to the preparation of the mixture, information should only be considered from the official instructions of the tool manufacturer. At some firms, the ratio of gasoline to oil for a chainsaw is 1:30, 1:40, or even 1: 100. Therefore, you should not be lazy to read the company instructions. In order for the proportion to be accurate, it is convenient to use a disposable syringe. “twenty”. If you use a large amount of the fuel mixture at once, you can limit yourself to a measuring scale, which is available on virtually all standard oil containers.
Which oil for the chainsaw chain is better to use, the choice of chain oil for chainsaws and chainsaws
Which oil to choose and use to lubricate the chainsaw / chainsaw chain.
It must be remembered that the storage of the fuel mixture for the future is in most cases unjustified, except when the fuel mixture will be used within 1-3 days.
Varieties and quality of oils for chainsaws
Parameters by which it is customary to compare the quality of push-pull oils:
- base (mineral or synthetic);
- lubricating characteristics;
- environmental parameters;
- exhaust toxicity;
- wear and burning rings;
- washing properties;
- degree of smoke formation;
- degree of biodegradability.
- low quality fuel is used;
- Chainsaw loads are long and intense;
- prolonged and incorrect work "gas".
During prolonged use it is not recommended to constantly change the speed. the more stable the engine (that is, the less often the speed changes), the longer the saw will work in time with intensive use. Synthetics is precisely why it was originally intended for powerful professional tools. where the pistons are seriously heated and the loads are high. However, for household saws, synthetics definitely will not hurt.
For a chainsaw, the ratio of gasoline to oil in the fuel mixture is perhaps more important than quality. High-quality lubricant plus the right proportion are excellent conditions for operating the unit. One of the few drawbacks of "synthetics" is the high price. If finances allow, the choice should be stopped with synthetic oil, best of all. the same manufacturer as the tool.
Chainsaw Chain Lubrication
Quite often the question arises. what oil to use for chainsaw chains? To lubricate the working element of the chainsaw, its chain, it is necessary to use special oils designed specifically for this purpose. These are the so-called adhesive oils. Many use other varieties, motor or for transmission, but they will not be as effective as special adhesive oil. This is due to the fact that in the structure of special lubricants there are adhesive components that force it to “stick” to the chain. Accordingly, this product is less lost when the chain is rotated, and the chain and tire are less worn and their service life is increased.
An essential parameter for oil intended for chain lubrication is density. Too liquid products are subject to increased consumption. Oils are also produced, which subsequently decompose, which allows not to harm the environment. They use a plant base. Their cost is slightly higher than usual.
Oil is added to lubricate the chain in a special tank up to the neck. It should be added during refueling, because if the lubricant for the chain is shortened, it may end earlier than gasoline. Which, in turn, can lead to overheating of the circuit. In the documents, the manufacturer indicates the oil consumption for the chain. However, it often differs up or down, due to differences in properties. When operating in frost, oil with a low thickening temperature must be poured in order to avoid failure of the oil pump.
A chainsaw is a convenient, productive, reliable tool. It is indispensable for construction work, the preparation of firewood, sawing trees or logs. With proper use, appropriate maintenance, compliance with safety requirements, this device will last a long time and will delight you with smooth operation.
What Oil To Pour Into A Chainsaw Partner
All About Choosing Chainsaw Oil
The resource of any chainsaw, no doubt, depends on the properties of its maintenance and operation. An important requirement for this unit is the timely lubrication of all its moving parts. Chainsaw oil is available in various types, namely, motor and chain. The motor is poured into a gasoline engine, and the chain is designed for the saw chain. We will figure out how to choose the right oil for the chainsaw.
What parts of a chainsaw need oil
If you look closely at the working chainsaw, then immediately its main moving part, the saw chain, which slides along the tire during sawing, is visible. Since the law of friction still exists, both parts wear out evenly. To slow down this process, it is customary to use chain oil, specially made for the lubrication of saw chains.
Chainsaws can be equipped with four-stroke engines. and two-stroke. In 4-stroke units, the crank group is lubricated with oil located in the crankcase. Two-stroke engines slightly differ in their own design and mechanism of operation. Gasoline of this type of drive goes straight to the place under the piston where the crank mechanism is located, which has several bearings and bushings that need lubrication. Therefore, oil for two-stroke engines of chainsaws is added to gasoline, so that, getting on the rubbing parts of this block, lubricates them.
Engine oil selection
Oil created for a 2-stroke engine must meet the following requirements.
- The lubricant should create a minimum ash during combustion. In the standard, it should burn one hundred percent.
- The lubricant must have good solubility in gasoline and a high degree of purification from various impurities that can cause clogging of very narrow carburetor channels.
- The oil must have the highest anti-corrosion, anti-wear and lubricating properties.
There are certain standards of oils created for 2-stroke engines: TC-W3 and 2T. TC-W3 standard grease is used for water-cooled engines (outboard motors, jet skis). 2T oil is used as an additive in gasoline for 2-stroke engines with air cooling (lawn mowers, mopeds, chainsaws, etc.).
MOTUL Outboard Tech 2T Oil
Oils can be green, red or blue. This is done so that their presence in gasoline is easily determined.
When using poor-quality grease, the entire piston group of the engine can fail due to the formation of soot under the piston rings. As a result, they will not be able to compress, and on the walls of the cylinder galling is formed. Also, improper lubrication of the bearings of the crank mechanism leads to their overheating and, ultimately, to jam. Important: it is forbidden to use diesel oil to prepare the fuel mixture, since it does not correspond to any of the above parameters.
Overview of ICE Oil Manufacturers
Among the manufacturers producing the best two-stroke oils, we can confidently name 2 leaders. these are the companies Husqvarna (Husvarna) and Stihl (Stihl). Companies produce not only conventional mineral oils, but also synthetic lubricants designed for 2-stroke engines operating in difficult conditions.
Husqvarna HP
This is a Swedish manufacturer, which includes several well-known brands, including the Partner (Partner) company, known for its garden equipment for semi-professional and professional use. Husqvarna produces not only equipment, but also high-quality lubricants used on almost all brands of gasoline powered tools.
The photo below shows a 2-stroke Husqvarna HP oil, which contains special additives that can compensate for the poor quality of fuel, which is not uncommon in our country. After all, the octane number of gasoline purchased at a gas station is not always consistent with the declared one.
This grease is green and contains a semi-synthetic base. It can be packaged in 10-liter containers, and in a liter. The mixture is diluted in a standard proportion of 1:50 (20 g per 1 liter of gasoline). But when the engine has not yet been run-in, or work is to be done in the cold, the proportion can be increased to 1:40.
Stihl hp
The grease has been specially developed for Stihl engine technology. It has a mineral base, has high lubricating and cleaning abilities, and it can be used at an ambient temperature of at least 10 ° C.
The bottle has a special dispenser that allows the process of mixing the fuel mixture without the use of additional measuring containers.
The grease has a red color and is stored for no more than 4 years in a closed container. The latter can have different capacities, both large and small (for a single refueling). For example, there is a 20-gram container for sale, the contents of which are added per 1 liter of gasoline. This is a very convenient option for owners of chainsaws, using them from time to time. Important: a mixture of gasoline with this oil should not be stored for more than 1 month, because during this time it will already lose its lubricating properties.
Preparation of a fuel mixture for two-stroke engines
The video shows how to make a fuel mixture for two-stroke engines. Refueling mtkosa, chainsaws and.
Chainsaw refueling
3 part of the course. What you need to know about chainsaws, before using them. Join us on social networks.
Stihl HP Ultra
Oil belongs to the highest category. It is created on a fully synthetic basis, has a green color and has high lubricating properties, and thanks to salt-free additives it does not create carbon deposits.
The oil was specially developed for the lubrication of engines operating for a long time at high loads and low ambient temperatures, up to 25 ° C. In addition, this lubricant does not harm the environment. If shed on the ground, it will decompose by 80% in 21 days. The lubricant is packaged in bottles of 100 ml and 1 liter.
Video: What Oil To Pour Into A Chainsaw Partner
How to determine the ratio of gasoline to oil
The fuel mixture used in 2-stroke engines is prepared from a certain amount of oil and gasoline. The latter must have an octane rating of at least 90 and be unleaded. Best for these purposes is the fuel grade AI-92.
Gasoline with an octane rating of 95 is not recommended, since it contains many different additives that harm two-stroke engines.
To prepare the mixture, use only engine oil from reputable manufacturers. The grease should be designed for high speed engines with an air cooling system. This component, designed for low-speed engines (moped, motorcycle, snowmobile), is prohibited to use.
When preparing the mixture, it is required to strictly observe the proportion of gasoline and oil. As a rule, this is 1:50, that is, you need to take 100 ml of oil and dilute it in 5 liters of gasoline. This rule changes slightly if the engine or piston system is new and break-in is required. In this case, the oil-gasoline ratio may be 1:40. For a break-in, 2-3 full refueling of the unit with a fuel mixture with such a ratio is required. If you dilute the fuel mixture in the proportion of 1:30, then inevitably a deposit forms on the piston and inside the cylinder, which, as already mentioned, leads to the breakdown of the entire crank mechanism.
Below is a table that helps you quickly determine the gas-oil ratio if you need to prepare a large amount of the fuel mixture.
Rules for the preparation of the fuel mixture
It is necessary to dilute gasoline with oil in containers that are resistant to the effects of petroleum products (plastic or metal canisters). It is not recommended to use plastic bottles for water, juice or milk for these purposes, since food plastic decomposes under the influence of gasoline. As a result of this process, the fuel mixture will change its properties, and it is difficult to predict what effect it will have on the engine.
The combustible mixture for the chainsaw is easy to prepare.
- Take the required amount of lubricant and pour it into the prepared container. Pouring all prepared gasoline into a container with oil should not be enough, half of the required amount will be enough.
- Shaking the container slightly, wait until the lubricant has completely dissolved in gasoline.
- Now you can fill in the remaining gasoline, mixing it well with the mixture in the tank. This completes the preparation of the fuel mixture for the chainsaw.
Before each refueling of the chainsaw, the combustible mixture must be shaken. Also, do not forget to tighten the cap of the fuel tank well, otherwise this will lead to lean mixture and engine failure.
The finished fuel mixture is best used immediately. Therefore, it is necessary to cook it in such a quantity that it is enough for the estimated amount of work. If the mixture still remains, then it is impossible to store it for more than 1-1.5 months. During this time, it will lose a significant part of its lubricating properties.
Chain oil selection
After each refueling of the chainsaw, do not forget to check the amount of oil in the oil tank. In a chainsaw, the oil pump is engaged in the delivery of lubricant to the tire along which the saw chain slides. Normally, the refueling of both tanks. fuel and oil. should be done simultaneously. Chain oil must be poured into the appropriate tank up to the neck. Otherwise, it may end earlier than fuel, which will lead to overheating of the circuit and tire.
Chainsaw chain lubrication oil should be developed specifically for this purpose. The use of other lubricants is inefficient and reduces the service life of not only the saw, but also the unit tires. This is due to the fact that the chain oil in its composition has adhesive additives, due to which the lubricant literally “sticks” to the chain. This property of the oil reduces its consumption, as a result of which the lubrication of the tire of the chainsaw and the saw chain improves, and their service life increases.
An important parameter of chain lubrication is its density. If you intend to use grease that is not intended for chainsaws, you may notice that oil is leaking during operation of the unit or after it has stopped. This fact indicates that the grease is too fluid. In addition, the liquid lubricant will quickly scatter in all directions and, accordingly, will quickly end.
When operating a chainsaw in winter, use oil designed for low temperatures to lubricate the chain, otherwise the oil pump will fail. Therefore, the grease remaining in the tank must be replaced with a low-temperature one.
Leading manufacturers of gasoline powered tools, such as Stihl, Husqvarna, Makita, Bosch and the manufacturer of Oregon chainsaw components, recommend special high-adhesion oils, including biodegradable ones, for use. But the oils of well-known brands have the only drawback. the price is 300 rubles per 1 liter and above. In addition, the grease in the reservoir may thicken over time and clog the channels. For this reason, it has to be drained, and this already increases consumption. But despite this, we have to admit the fact that only the use of special lubricants can extend the life of the chainsaw.
Oil Recommendations
It should be noted that there are fakes on sale for well-known brands, by buying which you can ruin your chainsaw. Therefore, lubricants must be purchased only from authorized dealers who have product certificates.
According to some users, the lubrication for a chainsaw chain can be replaced with any mineral oil with a viscosity of 15-40 for the summer period and with an index of 10-30 for the cold season. The brand can be M8 or M10. Also, many owners of chainsaws are beginning to wonder whether it is possible to replace 2-stroke oil with something. Experienced craftsmen are extremely advised not to add other lubricants to gasoline, since it is possible to completely disable the engine of the unit, the repair of which will take as much money as you do not save on lubrication. over, if you count, then one liter of oil is enough to make 50 liters of the fuel mixture, which can be spent only by working on a logging site.
What Oil Need To Be Poured Into A Chainsaw
The ratio of gasoline and oil for chainsaws: how and how much
From the very beginning of their own appearance, chainsaws once a year gain momentum in popularity and demand among consumers in different countries (see rating of the best chainsaws). What kind of oil is poured into the trimmer? And this is not at all breathtaking, because they are irreplaceable assistants in the field of agricultural activity, tree splits, are also successfully used in repair work. But, even without looking at their so-called popularity, they, like you and me, require attention and a typical approach.
This is especially true of gasoline-oil consistency, which you fill specifically in your own "favorite." what oil to fill in chain. Because this additive, namely its quality directly affects the work and productivity of the chainsaw.
In this article we will look at all the questions regarding this needed water. We learn how to breed gasoline with oil for a chainsaw, what proportion of oil and gasoline for chainsaws, and also what oil to add to gasoline for a chainsaw. So let’s get started.
Device Aspects
At the moment, you and I will “plunge” into the very core of this tool so that you can at least give a general idea of what your “assistant” consists of. What type of oil to put in a chainsaw to lubricate the chain. In fact, this kind of tool can with all responsibility be attributed to the mechanisms of the traditional direction, which work as a means of engaging the gasoline engine. Two-stroke engine Without exaggeration, we can say that this type of tool is the simplest of all other mechanisms, because the saw does not have a gearbox and is equipped with an ordinary two-stroke engine with one cylinder and running on gasoline.
The main advantage of the chainsaw will be that it is arranged quite easily, which contributes to increased reliability, as well as failure-free operation in languid and complex criteria. Next, we consider in more detail the design of the saw, so:
- engine;
- clutch;
- ignition system;
- carburetor (see carburetor adjustment);
- fuel system;
- air cleaning system;
- starter;
- chain (see how to sharpen a chain);
- the tire;
- chain brake;
- chain tension mechanism;
- chain lubrication system (see chain lubrication oil).
In fact, they figured out the device, but now the lubrication of chainsaw parts remains an important issue. What kind of oil to put into the saw to lubricate the chain. Many do not understand why it is needed at all? The answer is quite simple, like all mechanisms, a chainsaw, especially its individual parts, require special care, including repeated lubrication.
This is necessary in order for your tool to serve you for many years, because during operation, the chainsaw parts create a movement that should be smooth, smooth so as not to destroy nearby parts.
Because everyone understands that the friction force violates the surface, and here, if you do not need to lubricate the chainsaw, the parts will simply wear out quickly and the tool will go out of tune. Is this necessary for you? I don’t think so. What Oil to Pour into AURAMM.RU Saw. Therefore, you need to bother about your own chainsaw so that it “has the strength” to serve you for long years.
When choosing a chainsaw, you need to focus on your needs, why do you want to use it.
If for you it will be necessary to take it in seemingly, then choose mini chainsaws.
For woodworking, coal-powered circular sawmills are better suited.
Choosing the right and high quality oil
Naturally, after you got the device, you immediately had a question: what oil to dilute gasoline for a chainsaw? If you take proper care of the equipment created for work in the construction and gardening fields, you can significantly increase the level of activity of the specific work of the device itself and not encounter breakdowns of a different nature. Lubricant It should be noted that the introduction of the correct lubricant and fuel is the most important factor in the specific performance of a device. Although the main tasks for the owners of this technique are specifically with the choice of oil for their own "favorites". In this paragraph you can find out how to select a lubricant:
- First, what I would like to direct your attention to is that virtually all chainsaws have a carburetor push-pull engine. Also in their "arsenal" there are two specific tanks, and specifically: gasoline and oil. In order to choose oil for a chainsaw, you need to know certain aspects of this kind of choice.
- Firstly, do not forget that, for example, Russian-made chainsaw models require the use of ordinary oils that are used specifically for bikes, and tools that are made abroad need branded oils, because their requirements are significantly exaggerated.
- In fact, if you understand this, then only you, as the owner of the equipment, will be able to determine which specific oil to use for you.
Which oil for the chainsaw chain is better to use, the choice of chain oil for chainsaws and chainsaws
Which oil to choose and use to lubricate the chainsaw / chainsaw chain.
What is better for lubricating the saw chain: oil or mining?
When arguing and justifying anything worthless, take a look at this video, which is the right thing to use to lubricate the saw.
Naturally, you can pour Russian-made oil into the imported chainsaw. But then you should be prepared for the fact that the power and productivity of your tool will significantly decrease.
The ratio of gasoline to oil
And now let’s look at the question that worries the owners of this equipment: how much oil to add to gasoline for a chainsaw? First, it should be noted that this kind of fuel mixture is made specifically from 2 high-quality components. Unleaded gasoline The first, the so-called additive, is unleaded gasoline, which has an octane number of at least 92. For example, AI-95 and AI-92 gasoline will serve tremendously for this purpose. The second component is a special oil specifically designed for gardening technology with a two-stroke engine.
At the moment, we will figure out what ratio of oil and gasoline for a chainsaw is needed, because this issue must be approached with all responsibility. Naturally, you can add oil to the imported chainsaw, how much oil to add. What kind of gasoline needs to be poured into a chainsaw. AI-95.V is also available for sale. So, almost always for one liter of gasoline specifically for you you need in some places from 20 to fifty ml of oil.
And if you are concerned about how much oil to pour into gasoline for a chainsaw, which has a specific power of about 1.5 kW, then in this case 25 ml of oil per liter of gasoline will come in handy for you.
For significantly powerful tools, about 30 ml are mainly used, and from time to time even more. You will naturally be able to find out the necessary information specifically on oil containers, but you will still find clear data from the table for diluting oil and gasoline for your model’s chainsaw from its annotation.
How to mix gasoline with oil?
In order for the tool to serve you for more than one year and also so that you do not encounter any problems associated with its breakdown, you should know how to properly prepare a mixture of gasoline with oil for a chainsaw. Today, web forums just explode from questions regarding this topic. What kind of oil do we pour into our chainsaws and lawn mowers? Therefore, in this Fri, everyone will be able to get useful and reliable information. So let’s get started.
In order to make a concrete production of this kind of consistency, you need to purchase AI-95 or AI-2 gasoline, in general we announced this earlier.
We also clarified the fact that it was necessary to use exclusively unleaded gasoline, but did not specify the reason for this “whim”. Everything is simple, because if you use leaded fuel, then in this case you will have obstacles with the engine, because it will simply fail. Combine oil and fuel in clear proportions It’s important to keep in mind that oil and specifically gasoline need to be combined in clear and serious proportions. And what kind of oil to pour into And what kind of oil to pour into a chainsaw viscosity is possible. In order to answer the question what is the proportion of oil and gasoline for chainsaws, you must first fish out that if you pour in excess oil, then in this case you can not avoid the appearance of soot on candles and pistons.
Lack of oil will cause scuffing on the pistons, as well as an abrupt breakdown of a particular motor.
The process itself is not something complicated, because everything is as simple as possible: you fill the necessary ingredients in a container, twist the lids and painstakingly mix, by means of tipping the container. Most of the owners use plastic and glass bottles for this manipulation.
But you need to keep in mind that through such measures static electricity can occur, therefore it is necessary to be as careful as possible. Remember that not a drop of water or any foreign elements should get into your mixture. In addition, do not forget the aspect that you should store the finished oil-fuel mixture for no more than 20 5. 30 days.
To summarize.
In this article you got acquainted with what proportion of oil and gasoline for chainsaws and how to dilute gasoline with oil for chainsaws, how to refuel a chainsaw and what should be the ratio of oil and gasoline. Therefore, following all the tips and advice prescribed above, without fail, you can personally carry out this process.
See also the annotation on how to correctly run a chainsaw.