Which Side to Cut Laminate

How to saw a laminate without chips. How to saw a laminate at home

How and with what to saw a lamina,

Laminate was to the taste of many. this inexpensive floor material is very practical and beautiful. It’s just that not everyone can gently saw off even pieces from him. And you have to cut, and more than once. at the end of each row, at least. So how and with what to saw the laminate so that the cut line pleases the eye. we will consider the methods and tools that can be used to saw the laminate.

Pick up a hacksaw

Laminate hacksaw, of course, sawn, but not very suitable for such work. After all, the teeth of a hacksaw designed for woodwork are eerily large, and the top film of the floor covering is so thin. Togo and look. ugly marks will remain from these teeth. Yes, and sawing a pressed laminate structure with a hacksaw is hard. Hands get tired.

To get a better result, arm ourselves with a hacksaw with small teeth. For example, a hacksaw designed for sawing metal may well come up. It will be possible to avoid chipping at the cut, but cutting with a fine-tooth hacksaw will be more difficult than using a woodworking tool. However, if you do not intend to saw the laminate in large quantities, then this method is suitable. The cut quality, of course, is not ideal, but quite tolerable.

And here are the promised little tricks: before sawing, stick a piece of masking tape on this place. If this is done, then chips will not form at the cutting site. over, the laminate board must be placed face up. And so that the cut is smooth and clean, the hacksaw should have small, frequent teeth.

Since the laminate is pressed using special mechanisms, it is naturally better to saw it not by hand, but by an electric tool.

For example, an electric saw, (reciprocating saw), which is increasingly used by home craftsmen, is quite suitable for this.

We are equipped with an electric jigsaw

It is good if you have a jigsaw equipped with a file for wooden surfaces at home.

Using this tool is the best option.

Before sawing, with a pencil, mark the cut line, and then with a knife or awl cut through the film of the laminated coating. Now tightly clamp the board (face down).

The speed of the power tool must be high. It is necessary to try to cut smoothly enough, without jerking the jigsaw so that chips do not happen. Having adapted, it is possible to quickly and accurately saw through the laminate boards. over, an excellent result is obtained when cutting both along and across the board. It seems that the answer to the question, what is the best way to saw the laminate, is clear. of course with a jigsaw.

Video: How to cut electric jigsaw without chips

Circular Saw. Requires Expertise

And you can cut the laminate with a circular saw, equipping it with a disk for metal work. At the same time, we put the board prepared for cutting and the marked board on some even plane. The laminated film should not be on the bottom, as when working with a jigsaw, but on top. Slowly and smoothly moving the circular disc along the cut line, we get a smooth and high-quality cut surface. During operation, the disc does not get stuck in the laminate.

But for those who have never picked up such a tool, out of habit it will be hard. It is necessary to make a lot of effort and effort to achieve the desired result. Having acquired dexterity over time, it will be possible to saw the laminate very quickly and efficiently. But this process requires patience.

If you have not previously sawed other materials with this tool, it is better to give preference in favor of a jigsaw.

Cutter designed specifically for cutting laminate

This cutter is a bit like a guillotine. The sharpest knife, falling down from above, instantly cuts the laminate, like butter. The cutting line is perfect and as accurate as possible. Just cut this tool can only across the boards. And if you need to saw the floorboard along, then again we turn to one of the methods described above.

In addition, such a cutter is very expensive, so buying it can be beneficial only to professionals who are engaged in laying laminate flooring on an ongoing basis. If you just want to change the floor in a couple of rooms in your apartment, then you are unlikely to make such a purchase.

Important: with any method, it is better to measure several times, and cut it later. As a rule, laminate is bought a little more than it turned out according to calculations. It takes into account that you have to cut some boards, and then dock them correctly.

Video: Laminate Cutter

If you notice an error, not a working video or link, please select a piece of text and press Ctrlenter.

Updated: July 22, 2018

How to cut a laminate exactly at home without chips (photos and video)

Considering how to saw the laminate, it should be noted that the laminated coating is recommended to be laid according to the same technology as brickwork, that is, in a breakdown. Only in this case will the finished floor look natural and very attractive. The only drawback of such a stacking scheme is that it involves cutting the material in each row.

Which Side to Cut Laminate

Laying scheme of the laminate.

Laminate cutting is a very important task, the appearance of the floor covering will depend on the correctness of its performance. Therefore, such work must be approached with all seriousness, having first figured out how and how to saw the laminate.

Laminate Construction

To choose the right tool for cutting laminated panels, you first need to figure out what they consist of. Laminate is a finishing material having a layered structure, which consists of chipboard or fiberboard and special paper impregnated with melamine resins. In the process of its manufacture, all layers are glued together by pressing under high (high pressure laminate. HDL) or low (low pressure laminate DLP) pressure.

The device of the laminate board.

Thanks to this production technology, the material has the following advantages:

  • strength;
  • moisture resistance;
  • environmental friendliness;
  • resistance to aggressive substances;
  • long service life.

Structurally, laminated panels consist of the following layers:

  1. Bottom layer. It is made of plastic or tarred paper. Protects the material from moisture coming out of the subfloor. Some brands of laminate flooring are additionally equipped with a soundproof layer. Such panels are recommended to be installed in apartments located on the upper floors in order to muffle noise from neighbors from below.
  2. Base. It is made from fiberboard or particleboard. The strength and moisture resistance of the material depends on the quality and thickness of this layer. The butt part of the laminate, called the lock, crashes into the base.
  3. Decorative layer. Thanks to him, a unique panel pattern is created with imitation of natural stone, tile, wood, etc.
  4. Protective layer. It consists of acrylic and melamine resins that protect the material from wiping, shock and other mechanical influences.

Laminate Cutting Tool

You can cut the laminate with the simplest metal saw.

Processing of laminated panels should be done so that the cutting line is even, without chips, burrs and other defects.

For cutting this material, you can use both mechanical and electrical, including narrowly targeted, tools, namely:

  • a hand saw for wood or metal;
  • jigsaw;
  • circular saw;
  • special cutter.

Consider each option in more detail.

Laminate cutting with a hand saw

The cheapest tool that allows you to cut the laminate is a conventional hacksaw, which is available in the arsenal of each owner. Unlike chipboards, laminated panels lend themselves well to similar processing. the fishing line in this case will not be ideal, since the hacksaw teeth leave small chips after themselves. However, this is not critical, because small damages at the end can be hidden by a floor plinth mounted around the perimeter of the finishing base.

To obtain an acceptable result, it is necessary to use a tool with small teeth, for which a metal saw is suitable. With its help, you can get a better cut, but you will have to cut much longer than a hacksaw on a tree. Therefore, working with a hand saw is relevant only for small volumes of building material.

Before cutting the laminate with a hacksaw, it is placed on a hard and even surface with its face up, after which it is cut with smooth movements. In the process of work, it is not worth putting pressure on the saw, as this will only worsen the quality of the cut.

Using a jigsaw

Working with a jigsaw will save a lot of time and effort.

The most effective tool to quickly and efficiently saw through a laminate is a jigsaw. It is very convenient to use, so even a novice master can handle it. In addition, it is characterized by an acceptable cost, which is why its great popularity is due. Sawing with a jigsaw is performed at high speeds, which results in a clean and even cut line.

The quality of the work performed, to a greater extent, is affected not by the tool itself, but by its cutting part. If speed is not the first priority, that is, for a short period of time it is necessary to process a lot of material, then a saw with large teeth should be installed in the jigsaw. The larger the teeth, the faster the laminate will cut.

At the same time, with an increase in cutting speed, its quality decreases. This should also be taken into account. For fast cutting of panels it is recommended to use a saw marked T101D or 344D. To obtain a clean cut, a cutting blade marked T101B is used, equipped with small teeth.

To cut the laminate with a jigsaw, you need to install a saw with reverse teeth, since in this case the likelihood of chips and other mechanical defects is reduced.

It should be noted that with a jigsaw you can create not only straight lines, but also curly cuts. First you need to prepare a template from a cardboard box of the appropriate form. Then the template rests on the front side of the panels and is outlined with a simple pencil. After that, the cut is made according to the obtained curve.

Read more:  What Is A Screwdriver For?

Other laminate cutting tools

To cut the laminate with a circular saw, a disk with small teeth is taken.

In the absence of a jigsaw, it is possible to cut a laminated board using a circular saw and a disk with small teeth. The cutting technology is no different from the previous version, however, in this case, achieving an even cut line will be somewhat more difficult. To simplify the task, you can use not a circular saw, but a stationary circular. However, due to the high cost, not everyone can afford such a tool.

Answering the question of how to saw laminate flooring, it should be noted that in the modern construction market it is possible to purchase highly specialized equipment designed specifically for processing laminated boards. Such a tool is a laminate cutter. Outwardly, it resembles a clerical guillotine for cutting paper. The cutter consists of a horizontal platform on which the material rests, and a sharp blade, driven by a lever.

This tool does not produce noise during operation, does not emit dust and does not chip. It should be noted that only longitudinal sections can be made with the cutter. For transverse cuts, you need to use one of the tools described above.

Laminate can be cut using various tools, both mechanical and electrical. The choice of this or that option will depend on your financial capabilities and the amount of work ahead. If it is necessary to saw a large number of laminated panels, then the best option is a jigsaw or a circular machine. For several cuts, an ordinary metal saw will suffice.

What kind of jigsaw file to saw the laminate ?! Master answer

This short review will not take you much time, but it will help you decide on the choice of a file for sawing a laminate. First of all, we define: a laminate refers to wood products and we need wood saws for a jigsaw.

For cutting wood and laminate, there are several options for suitable files T101B, T101BR, T101D, T101AO, T101BIF.

File for cutting laminate T101B

Personally, my partner and I use this type of T101B files, I will explain why. In this type of blade, the teeth look up. Modern jigsaws have a pendulum system. The file returns to the sole of the tool and the sawed material at the same time both forward and upward. Thus, the T101B of HCS marking metal presses the board to the bottom of the jigsaw and the part does not hit the desktop. Here’s an article about the necessary tool for laying laminate flooring.

Laminate cutting with this type of blade occurs quickly, as much as possible without chips, however, marking of cut lines must be done on the back of the laminated strip. What for a beginner master can cause difficulties. This type of blade is relatively inexpensive, but dull enough quickly. It is better to set the speed of the jigsaw to cut the laminate as high as possible. this will prevent chips.

Laminate saw file T101Br

Previously, we sometimes used this type of file to accurately cut the laminate in the upper part, when the cut part had a complex pattern. However, then they completely refused. At T101Br, the teeth are downward and a very strong beating occurs when the pendulum moves. I do not recommend to use.

Saw file for parquet board T101D

T101D has a large tooth. Rather, it is suitable for cutting plywood, boards. We do not use this type of blade to cut the laminate, but we use it for the parquet board according to the marking from the back. However, this type of knife can be used to cut the laminate, but chips can occur.

Laminate cutting blade T101AO

T101AO shorter length of about 75 mm, which does not affect the cut of the laminate. It has a fine tooth, which gives an even cut. However, the speed drank very low. It is not practical to use for normal work. We use it only for curvilinear cutting, such as bypassing heating pipes. For a curved cut, set the jigsaw speed to medium or lower.

Laminate saw blade T101BIF

This saw blade is made of bimetallic (Bim), the most durable material, therefore it serves for a long time. The teeth are evenly spaced without a specific orientation.

T101Bif can be safely used both for cutting along the front of the laminate and for cutting along the back. It has a fairly even cut and good speed, slightly inferior to the T101B in it, when working with a jigsaw it does not hit the workpiece.

For self-laying laminate flooring without much experience, I would recommend this particular type of file. At the manufacturer we use Bosch or Practice.

How to saw a laminate? How to do it right? Curly and straight cuts.

It is known that in the production of cutting lamels is made using special machines that are equipped with two files:

  1. The first is called trimming, it is small and rotates in the direction of movement of the part, while removing the lower layer;
  2. The second produces the main cut of the board, rotating in the opposite direction.

The content of the article:

For such a machine, accurate work is always characteristic, as a result of which lamellas are obtained without chips with right angles. But what if you do not have such a tool when you lay the laminate flooring at home? How to saw a laminate? Achieving maximum results is possible even in everyday life, if you use the "right" devices.

How to saw a laminate at home?

You can choose one of the most popular and affordable options. Before you pay for the device, learn more about its capabilities and the nature of the work:

  • Hacksaw. This is not to say that this is a modern option, but in some cases it is very helpful. The hacksaw never fails. For the best result, it is better to use a hacksaw for metal or wood with a small tooth. Start cutting from the back of the panel to prevent possible chips on the surface of the board;
  • Angle Grinder. This is an angle grinder with a disc for metal. How to saw a laminate? Lock the lamella and slowly lower the angle grinder so that it does not escape from your hands and does not stop. Be prepared for the fact that during operation there will be an unpleasant odor due to heating of the disk;
  • cutter. Here is another popular tool for cutting laminated material. It allows you to cut boards quickly and efficiently. Cutter effortlessly cope with both thin and thick panels. It is impossible to achieve such an ideal result either using an angle grinder or using an electric jigsaw. This is a device with a sharp blade, which is easily driven by a handle. Such a mechanism works very quietly, without noise and dust and does not need power supply;
  • a circular saw. Which file to saw the laminate? This is an option for a neat cut, equipped with a special disc. Place the board face up on a hard, level surface, securely fasten it and apply the cutting line. Then smoothly lower the disc angle grinder and gradually move it along the intended line without getting stuck in the board. This option requires skills in working with a circular saw, as well as great patience. But, the advantage is in high-quality and quick result. Are there any downsides? Yes, if the minus can be considered the smell of a burnt tree, which appears during the sawing process;
  • electric jigsaw. This is a fairly effective, but simple option. Make sure that the jigsaw is equipped with a special wood nozzle. Before starting work, you need to fix the lamella on the floor. Turn on the device and set it to high revs to protect the material from possible chips. Your movements should be smooth.

! Work with a jigsaw must be at least two people.

Laminate file

I would like to pay special attention to the nail files for the laminate, which are used together with a jigsaw:

  1. The goal is a quick cut: if you need to cut many boards at once in a short period, it is better to choose the option with a large tooth. The fact is that the larger the tooth, the faster the work will proceed. The only negative is that the cut will be less accurate, the cut is not smooth. For this purpose, as a rule, they buy a tool marked T101D, since it is suitable even for a thickness of 75 mm. For 100 mm, select 244D, 200 mm. 344D;
  2. the goal is a clean cut: here you need to use option T101B. A smaller tooth is characteristic of it, so the cut is smoother. Chips in this case are absent. Of course, even 75 mm can be cut with such a file, but it will take several times more time.

The file for the laminate is equipped with a back tooth, which, when compared with other options, is directed in the opposite direction. Why is this needed? This is done so that the chips are not formed on the front side of the lamella and the appearance does not deteriorate.

! Such boards can be easily cut with a blade with small divorce and moderate size of teeth. In this case, the speed of the jigsaw should also be moderate. So the tool does not get stuck and does not tear the edges.

How to cut a laminate: straight and curly cuts

Video: Which Side to Cut Laminate


How to make straight cuts?

Method 1 You can use a hacksaw or circular saw with the maximum number of teeth to avoid chipping. First make a markup and mark the part of the board that you are going to cut. This can be done with chalk and a pencil. Erasing chalk then is very simple. Well, after that just cut the lamella along the marked line.

Method 2 You can also use a jigsaw. This option is several times simpler than the previous one. Fix the guide on the device, and then wrap it around the edge of the workpiece. In this case, the movement of the file will be smooth relative to the edge.

! Do you work with thin slats? Be prepared for the appearance of chips on its front. The fact is that in the first embodiment, the instrument will move up. To prevent this from happening, you can place the workpiece face down. Another solution is the use of anti-slip liners.

How to make curly cuts?

How to saw a laminate in a curve? For such work, only a jigsaw with a special blade with very small teeth for laminate floors or even with a standard blade is suitable. A special option is better, since it helps to cut with a pattern up and without chips.

  1. First, prepare the desired template from paper or cardboard. It is needed in order to calculate the cut and maintain the integrity of the board;
  2. attach a template and circle the desired pattern;
  3. cut out the picture and attach the template again to make sure it is accurate;
  4. now simply circle the sample on the surface of the lamella;
  5. make a cut. If you are using a standard canvas, lay the board with the pattern down and attach the template upside down. Keep the jigsaw only upright. If you need to cut the front side, stick a strip of masking tape on the cutting line so that you do not have chips when cutting. Then measure over the tape those lines along which you are going to saw the lamella. To do this, use a special canvas designed for such flooring.
Read more:  How To Install A Plow On A Tiller

! Sometimes a template needs to be applied several times so as to obtain a sample of the desired shape. In this case, it is important not to rush: take the proper time to make the template, and then you will spend less time and effort on cutting boards.

It is also noteworthy that it is the jigsaw that can cut all the chips. As a result of its use, the edge of the product is smooth in a certain direction. To carry out such a cutting, change the installation angle of the jigsaw ski and get to work.

Do not try to use a hacksaw in the case of curly cuts. You will not achieve the desired result and only spoil the material. First decide on the option of cutting (curly or straight), and only then choose the better to saw the laminate.

Video than sawing a laminate?

How to saw a laminate? How to do it right? Curly and straight cuts.

4 (80%)
Voted 2

How to cut a laminate: how to choose the right tool

In order to properly lay the laminate on the floor, you need to be able to not only connect the laminate panels, but also properly cut them. Otherwise, "fit" into the area of ​​the room, as well as to comply with the traditional chess pattern of the coating will be impossible. Since you can’t take laminated boards with your bare hands, you can entrust them to cutting with one of the hand or electric tools.

Selection of cutting tools for laminate flooring

The main characteristics that a tool for cutting a laminate at home should have are:

  • Ease of use
  • compact and light weight
  • the possibility of obtaining a smooth cut, without cracks and chips

The last point, the meaning of which is not to spoil the appearance of the laminate board after cutting, is crucial for most home masters. However, its significance is still exaggerated. In any case, chips up to 5 mm in size on the finished coating will not be noticeable. defects along the edge of the panels will disappear behind the skirting boards.

So, which tools are most suitable for cutting laminate?

Tool number 1. Jigsaw

The best result in the cutting of the laminate can be achieved by applying an electric jigsaw for this purpose. This is an easy, very convenient tool to use, to which any master novice will quickly find an approach. Even a woman or a teenager. Sawing with a jigsaw is performed at high speeds, which avoids damage to the fiberboard structure. If you act quickly, confidently, then the cut will be almost perfect.

The main thing in using a jigsaw is choosing a file. A modern tool is usually initially supplied with special files for cutting laminate. They are distinguished by a special shape, pitch and method of tooth alignment. However, ordinary metal saws. narrow, with small teeth, can do this worse.

In order not to damage the decorative surface, the cutting line is applied (in pencil or chalk) to the underside of the laminate board. It is laid on the table (chair) with the wrong side up so that the part to be cut is suspended. The laminate lying on the table is fixed with one hand, and the other part is quickly cut off with the other.

The fret saw allows to cut a laminate quickly and safely

Tool number 2. A circular saw

A neat cut along the edge of the laminate can be obtained using a circular saw with a metal blade. Working with a circular saw is more difficult than with a jigsaw, so this requires some skills. If you have them, then it will be possible to saw through the laminate quickly, evenly, practically without chips.

The laminate board is laid on a hard surface with the pattern facing up, fixed. You need to cut it gently, with a little pressure, moving the disk along the drawn line, trying not to slow down in one place.

A circular saw requires dexterity, but helps to cut out a large amount of laminate in a quality manner

Tool number 3. Angle grinder (angle grinder)

angle grinder. a convenient tool, indispensable in the home master’s drawer. It can cut almost everything, including the laminate. For a beautiful edge, without cracks and chips, when cutting, you need to turn the laminate board with the front surface. In this case, discs are used for metal, for concrete or for ceramic tiles.

The disadvantage of using an angle grinder (and a circular saw too!) Can be called a large amount of dust, which will be emitted when cutting a laminate. Also, this action may be accompanied by the smell of a burnt tree. Therefore, you need to engage in cutting on an open bal-street or on the street.

To avoid chips, cutting a laminate angle grinder is necessary only on the front side

Tool number 4. Hacksaw

Laminate can be successfully sawn with a regular hacksaw on wood. But this will have to expend energy, because her teeth are large enough and will bite into the laminate, and not cut it. Smaller teeth in a hacksaw for metal. and it must be used for sawing.

Hacksaw is often used for cutting with small amounts of work. In construction teams, this method is not used, due to the increased time costs and complexity.

Cutting a laminate with a hacksaw. a laborious process

Tool number 5. Laminate cutter

The cutter for the laminate, on the contrary, allows cutting to be done on a professional level. Most often, this tool works like a guillotine. a knife, which, with the help of a handle, is lowered to the surface of the laminate and cut it. The torch operates easily, without chips and noise. To use it, you do not need to use force and possess skills. Perhaps this is the easiest tool to use, which allows you to get an excellent result in any conditions.

The design of the cutter allows you to cut the laminate only in the transverse direction

Since this cutter is used exclusively for laminate flooring, it makes sense to buy it only with professional installation. For finishing several rooms of the apartment, this option is considered impractical.

Tool number 6. Construction knife

An ordinary construction knife can also be used for cutting a laminate. For example, if you have almost finished the flooring device, it remains to cut one board, but suddenly the angle grinder has broken. There are no other tools at hand, but cutting needs to be done urgently. Then a construction knife will come to the rescue. Put a ruler on the front side of the laminate board, draw a deep cut along it with a knife. While holding the board on one side of the cut, push the other side. The laminate should break, just like ceramic tiles under the influence of a tile cutter.

For lack of other tools, a construction knife is suitable for cutting a couple of three laminate boards

As an epilogue

The choice of tool for cutting laminate is large enough. Indeed, qualitatively cutting laminate boards, with experience, can be done with almost anything. Only the amount of time and labor spent will be different. Therefore, when deciding in favor of one of the tools, focus only on your own preferences and needs.

How to cut a laminate? The better it is to saw at home, a cutter or guillotine for cutting linoleum, a saw blade or a file for a jigsaw on linoleum

In the process of laying the floor covering, namely the laminate, it is important not only to be able to correctly connect the panels to each other. It is also necessary to correctly measure the size of the panels in accordance with the area of ​​the room, and also not to break the traditional masonry in a checkerboard pattern. In such a situation, a reasonable question arises. why cut the panels measured in size? Let’s try to understand the situation.

Types of coverage

The choice of tools for cutting laminated panels largely depends on the type of lamella used. If flooring is supposed to be done independently and without the help of specialists, then it is better to pay attention to the soft types of laminate.

At home, it will not be difficult to cut a soft cork or two-layer vinyl laminate. Such varieties of laminated panels are characterized by high indicators of wear resistance and moisture protection, as well as the speed of masonry.

To cut this type of lamellas, you don’t need a special tool, it will be enough to arm yourself with an ordinary ruler, pencil or pen and a construction knife. First, the cut line is outlined with a pencil or pen, and then it should be carried out with a knife. After that, you just need to bend the canvas. If you need to make a curly incision, then for this action you can use large scissors.

However, for sawing other types of multilayer panels, which include high-strength fiberboard or chipboard, you need to choose more serious tools.

What to use at home?

When choosing a tool that is supposed to cut laminated panels There are several factors to consider:

    The tool should be easy to use and not cause discomfort. It depends more on personal preferences and handling skills.

Compact and lightweight objects are much easier and faster to wield, and during the repair, every minute counts.

Another most important point of all is that with the help of the selected tool you should get an even cut without chips or cracks. However, you should not focus too much on this factor, since minor irregularities will quietly hide under the baseboards.

Having become acquainted with the main characteristics, you can proceed to a more detailed study of tools for sawing a laminate.

One of the easy-to-use tools with which you can cut the lamella is electric jigsaw. The device has a small weight and even a teenager or a girl will quickly deal with it. The jigsaw works at high speeds, so the cut occurs carefully. One of the important factors when using this device is the correct choice of a jigsaw file. Modern models are usually equipped with special replaceable files for working on the laminate. From other files, they differ in the shape, location and size of the cloves. However, in the absence of specialized nozzles, narrow files with small cloves are also suitable for cutting metal products.

In order to avoid damage to the decorative side of the mark and all manipulations with a jigsaw with the panel should be carried out from the wrong side. It is necessary to place the canvas on a table or chair so that the cut piece of the lamella is suspended. Firmly pressing the panel to the table with your hand, you should quickly move the jigsaw along the cut line with a jigsaw.

To cut the necessary pieces of laminated panels is quite suitable guillotine. Unlike the previous device, the guillotine has a mechanical device. In appearance, it can be compared with large scissors. This cutter is silent, uncomplicated and accurate in operation. Using it, it is easiest to make a transverse cutting of the laminate, however, buying a cutter for repairs in the apartment will be inappropriate. Such a device is suitable for those who are professionally engaged in laying flooring, so it can be found for temporary use by familiar repairmen.

Read more:  How To Disassemble The Bosch Mfq 4080 Mixer

To cut the lamellas with professional machine tool you need to lay the panel on the guillotine support. Then the blade should be adjusted so that the mark for the cut coincides with the cutter blade. After that, you need to lower the guillotine handle, cutting off exactly and neatly the necessary piece of the panel. To obtain a smooth cut when sawing a laminate, you can use a circular.

However, in this case, the circular saw must be equipped with a special disc for working on metal. In addition, unlike a jigsaw, working with a circular saw requires some skills in order to easily cut even pieces of panels quickly and easily.

To work with circular it is necessary to lay the laminated panel face up and securely fasten it. During operation, you need to act carefully, pressing a little while moving the disc and not lingering for a long time in one place. Also, do not forget about the basic safety rules: the sleeves of the clothes must be fastened during operation, and you must also protect your hands.

Another tool that requires work skills is milling cutter. A manual design with interchangeable cutters is unlikely to be in every home, but can be found in professionally assembled furniture. The milling cutter is capable of leaving behind a perfectly even and smooth surface, and besides, a tool can cut various shapes.

Sometimes an assistant when cutting a laminate can become ordinary construction knife. It can be used for small amounts of work, for example, for cutting one or two panels, when there is no time to look for another tool.

When using a knife, it is necessary to lay the laminate face up, then make a deep cut in the marking area with the knife. Then, holding one side of the panel, it is necessary to press on its other part to the extent that it does not break in the place of the incision.

How to choose a hacksaw?

Often when carrying out work on laying a laminate, they resort to the help of such a popular tool as hacksaw. However, for efficient and quick sawing of panels, you need to choose the right model. Of course, in the absence of others, you can use a hacksaw on wood. But in this case, the process will be time-consuming, since the hacksaw on the tree has large teeth. Due to these features, the hacksaw will not gently cut the blade, but dig into it.

The best option is to choose a hacksaw for metal. It has small teeth and is able to cut the panel evenly.

However, it is worth remembering that the help of a hacksaw for metal should be resorted to only with small amounts of work. Unlike power tools, this one takes more time to cut and requires more effort, so professional builders do not use a hacksaw for this purpose.

Is it possible to use the "angle grinder"?

This tool, also called an angle grinder, is excellent for sawing a variety of materials, including laminated panels. Using this device you can get a smooth and accurate cut. To properly cut the laminate angle grinder, you need to lay the panel with the decorative side up, and also use special removable discs with small teeth for working on metal, ceramic surfaces or concrete.

Since during work with the angle grinder a large amount of dust and dirt is formed, and you can also smell the burning odor during the sawing process, it is better to carry out all manipulations outdoors. On the ground floor, you can extend the extension cord through the window and work on the street; on the upper floors, the un glazed BAL-KON is the best fit.

Another nuance when working with an angle grinder, as with a circular saw, is that you need to have at least a little experience with this tool. Insecure handling of the hand during sawing can lead to the formation of an uneven edge or it may completely break out.

How to crop on the floor?

Sometimes there are situations when it is necessary to trim the laminated panels that are already laid on the floor. Usually people with insufficient experience in construction work in this case are wondering how to do it right.

In addition, you can turn to a safer, but at the same time time-consuming method. the use of a cutter. In order to cut the laid laminate, you need to arm yourself with a professional cutter for working on wood. On the advice of experienced people, two parallel cuts should be made along the width of the narrow chisel, then select a cut piece of the chisel. And so, slowly remove the length of the panel to the desired size.

How to cut without chips?

In order to gently saw off the laminate of the required length, you need to carefully prepare for the start of work.

Initially, you need to decide which tool from the above work will be performed. And one should be guided in choosing not only the availability of the device, but also with the existing skills in handling it.

After that, you need to accurately measure the length of the panel that you want to cut. You should not hurry in this matter, because an error is fraught with damage to material. At the same time, do not forget about the thickness of the blade with which the blade will be sawn, and take it into account when measuring.

When measurements are made, and the place of the notch is marked with a pencil, you need to draw an even fishing line along which the laminated panel will be cut.

When all the preparatory work is done, you can go directly to the sawing process.

Which side to cut?

Typically, laminate panels are sawed across to clean the length. But sometimes there are situations when you need to cut the lamellas along.

In this case, it is better to use electrical appliances, since even a professional laminate cutter is designed to cut across the panel. The best assistant for solving this problem will be a jigsaw. It is with his help, even without special skills in handling the device, that you can easily crop the panel in a circle. both along and across.

See the next video on how to cut the laminate so that there are no fragments.

Than sawing a laminate. sawing a laminate

In recent years, among all floor coverings, it is the laminate that stably holds high positions in popularity. This is understandable, because the laminated board is very similar to wood, although it is made on the basis of high density fiberboard. The construction of the laminate is four-layer, and on the surface there is another layer in the form of a film, its purpose is decorative and protective. Laminate is quite easy to install. Like the vast majority of floor coverings, the laminate needs to be cut and adjusted to the size of the room, and this can be a problem for a beginner, because it is not known how to saw the laminate so that the cut is without the slightest cracks and chips.

Jigsaw cutting

Jigsaw

Jigsaw is one of the most convenient materials for sawing a laminate. Sawing should be carried out at increased tool speeds to reduce the possibility of deformation of the laminated board.

In order to do everything right, you must first prepare for the cut. To do this, from the outside mark a line with a pencil, on which the cut will be carried out. Now you need to hold the same fishing line with a sharp object, for example, a knife or an awl, and make some effort. This will allow you to cut through the upper protective layer, which in the future will help to create a more even and clear line cut board.

Now you need to place the board on a flat surface and fix it thoroughly. The part of the board to be sawn must be in limbo. Actually, now you can start cutting.

Laminate saws for laminate

You should also determine which file is best used. Today on sale there are nozzles for wood, including special ones for laminate.

If it is necessary to make straight sections, then the file can be wide, although for more complex cuts it is better to use a file with small teeth and a narrow blade. The narrowness of the canvas especially affects the beauty of the curly sections, and the narrower the canvas, the thinner and more accurate the result.

Also recently appeared on sale files with the opposite direction of the teeth, which perfectly cope with the task of accurately cutting the laminate.

Using a circular saw

A circular saw

A circular saw cannot be called optimal for cutting a laminate, but if a person has certain skills in working with it, then he should not have difficulties. Most often, this method is used when it is necessary to saw the laminate along, that is, when it is necessary to go through the entire length of the board. A circular saw can significantly speed up the cutting process and get high-quality material of the required size.

The disadvantages include the formation of the smell of a burnt tree. The saw should be with small teeth.

Using Angle Grinder

Angle Grinder

When using an angle grinder to cut a laminate, it is necessary to select disks for concrete or ceramic tile. Sawing is carried out on the outer, front side, to avoid the formation of burrs and chips.

When using the angle grinder, a lot of dust and burning is formed, and therefore it is necessary to protect objects in the room, after covering them with a film.

Using a Hacksaw to Cut Laminate

Hacksaw

The hacksaw is clearly not the leader in the rating, the better it is to saw the laminate, but sometimes a person has only it at hand. A classic hacksaw has very large teeth, and with their help it will not be possible to cut the board quite nicely.

For a quality cut you need a hacksaw with small teeth.

On wood

The obvious disadvantages include the duration of the process. Using a hacksaw can be justified if you need to file a small angle or make a cut across the board. Using a hacksaw to cut a laminated board along its entire length is a catastrophic waste of time.

Using a cutter

Special station

This tool acts on the principle of the guillotine, that is, its parts seem to clamp the building material, which must be cut, and then quickly cut off by pressing. The cut is very smooth. In addition, when using the torch, there is no noise and it does not form dust.

The design of the cutter is such that they can only make cross cuts, which significantly reduces the scope of its application, and therefore the cutter should not be bought for a single laying of the laminate.

Figured cuts

In some cases, for example, at the junction of a laminated board with pipes, it is necessary to make a cut of a certain shape, which is called curly. Theoretically, you can make such a cut with a hacksaw and a circular saw, although the jigsaw is a recognized leader in terms of ease of use.