What you can and cannot sterilize in a dry-heat oven?
Can cutters, files or buffs be sterilized in a drycooker?? Let’s see what materials can be used in the dry fryer.
To understand this question, you need to know the specifics of the drycooker.
Dry sterilization takes place in a dry oven by streams of dry air heated to 200°C (82°F).
So, only instruments made of good quality heat-resistant materials can be sterilized in a dry-heat oven.
- Stainless steel instruments for manicures, cosmetology, podiatry, etc.д.;
- Items made of heat-resistant glass for artists in the beauty industry;
- Steel handpieces and needle holders in tattoo machines;
- Metal cutters for hardware manicure;
- Ceramic cutters for hardware manicure;
- metal saw bases for replaceable abrasives (without the abrasives themselves).
Before sterilizing, make sure that the tools do not have plastic or rubber inserts.
What must not be sterilized in a dry oven?
Because the drydryer reaches temperatures of up to 200°C, you cannot sterilize your instruments and supplies that cannot withstand this temperature. They will burn or melt and cause a fire hazard.
- Rubber tools (except heat resistant silicone);
- plastic instruments;
- Wooden cuticle sticks;
- nail files and files;
- Absorbent cotton, cotton pads, bandages, tissues, cloths;
- Instruments with inserts of non-heat-resistant materials. For example, barber scissors with non-removable plastic finger inserts.
If you are not sure whether the instruments can be sterilized in a dry-heat oven refer to the manufacturer’s instructions or ask us by phone: 0675381969.
How files are handled in the home?
It would seem that why decontaminate manicure tools at home, if they are used by only one person? After all, in salons, there is a lot of traffic, so there’s no way to do it without it. But this is a misconception, because even home files over time accumulate microbes.
Disinfection is carried out with antiseptics or special ready-made solutions. But there is a variant to make a solution independently:
- In a small bowl pour 100 grams of alcohol and 10 g of boric acid salt.
- Then the container should be covered with the lid.
- Periodically the solution should be stirred until a turbid liquid is obtained.
- After that add 30 g of manganese.
- The solution should turn pink with a violet tint.
- Files are placed in this solution and put on a steam bath.
- To keep the tools should not exceed fifteen minutes, and the temperature should not exceed 50 ° C.
There is one more simple way of sterilization. the oven. The treatment of files is carried out in the following way:
- Manicure tools should be disinfected first.
- After that they should be washed.
- Then all files are thoroughly wiped with tissues.
- The next step is to spread the tools on an open surface, preferably using foil. It should be done in such a way that they are not in contact with each other.
- Sterilize at 180 to 200 degrees Celsius.
- After fifteen minutes the oven should be turned off.
Also note that this method is not suitable for all tools. Instead of the oven, you can just boil all the files for about fifteen or twenty minutes.
Tips for choosing the right file tips
Corundum manicure cutter is a universal nozzle and can be suitable for any work in the field of hardware manicure. The choice of cutters for the ˗ machine is a very important part before you start working on your nails.
For removing cuticles
There are several nozzles, the use of which will help to facilitate work with the cuticle at the initial stage of mastering the technique of hardware manicure. The cuticle must be lifted before the cuticle is trimmed. This can be done with a Cylindrical Cone cutter and the blunt side. The side with the pointed end is used for pterygium removal.
It is worth remembering that the shape is quite traumatic, so novice masters need to be careful when using this cutter.
After the work is done, you can proceed to cut the cuticle with the cutter “Ball”, which perfectly copes with this type of activity. After the cut, it is worth going over the cutter with a plain cylinder to clean off the dead skin around the cuticle.
To remove gel nail polish
The best gel nail polish remover is a hard cutter. It is worth orienting yourself according to the marks that are applied to the nozzles. It is best to lean towards the blue notches, but in some cases the green markings are more effective. As for the shape, it is desirable to choose cutters with a blunt end, so as not to traumatize the client. The “Corn” and “Cone” are great.
For shaping
There is no particular shape of cutters or material they are made of to shape the nail. Each craftsman uses the most convenient cutter for himself. If to follow the recommendations of experts, it is necessary to use universal nozzles “Flame”, “Cylindrical cone” and “Corn”.
For polishing and sanding
For a perfect result of polishing and buffing the nail, several cutters with different abrasivity are used. The coarsest ones are used in the final stage of the manicure to remove keratinized skin.
Cutters with a small abrasiveness are suitable for work with synthetic material. Nailpads with medium hardness are good for polishing the nail plate before nail polishing or extensions. The smallest bits grind the cuticle and the skin around it.
As for the shape, you should choose blunt-tipped cutters to polish the nail plate, and sharp-tipped ones to grind rough skin.
How to sterilize router bits?
To do this, you must first rinse the nozzles in water, place them in the machine on special stands and treat them for at least five minutes at 90 degrees Celsius. Manually using a plastic or brass brush under running water. This is the easiest and most accessible method, but it takes time.
How to sterilize milling heads at home
The oven is heated to 180-200 degrees; on a baking tray we spread food foil, on top. sterilizable cutters; sterilize nozzles for 20 minutes, after which the oven must be turned off and opened; after another 20 minutes the tools can be removed one by one and hermetically packaged.
How long should the instruments be kept in the Alaminol solution??
Alaminol for manicure tools is used in a 5-8% solution, the preparation of which requires taking 50-80 ml of concentrate and add 950-920 ml of water, respectively. To disinfect your instruments, soak them in a solution for 60 minutes and pay attention to all accessories.
Do new manicure cutters need to be sterilized? Answer: All reusable cutters should be sterilized before each use on a client, including new ones.
How long do you need to keep your tools in the Alaminol solution??
Alaminol for manicure tools is used as a 5-8% solution, which requires taking 50-80 ml of concentrate and adding 950-920 ml of water, respectively. To disinfect your instruments, soak them in the solution for 60 minutes and pay attention to all the accessories.
For all the steps to sterilize your manicure tools you will need the following.
- Disinfectant (concentrate). Pay attention to the shelf life and instructions
- Medical mask and rubber gloves. you will need them when working with a chemical solution
- Disinfectant box or tub
- Sterilizer.
How to disinfect saws properly?
To keep your nail file clean and always ready for use, clean it with a cotton pad and any disinfectant solution. This can be hydrogen peroxide or alcohol. As a last resort, instruments can be rinsed with running water until completely clean.
Sterilizer with quartz balls, for manicure, pedicure and cosmetology tools, sterilization temperature 250 degrees, sterilization time 20-30 seconds.
How to sterilize ceramic cutters at home?
How to store the tools if you don’t use Kraft bags? There is an alternative. ultraviolet oven. This is the kind of device that creates and maintains a sterile external environment in which instruments can be stored so that they do not lose their safety.
What materials are the cutters made of?
The materials used to make the nozzles:
- Ceramics. Cutters made of this material are used for grinding hard skin rollers. Such products remove unnatural coating better than others and allow the use of nozzles at low revolutions (up to 30 thous.).
- Hard-alloy cutters. These types of products grind the cuticle and lateral rollers. They take a long time to remove the gel polish, but the possibility of damaging the nail is negligible. To these nozzles in the manicure are inexpensive steel products without grooves.
- With diamond dusting. Such nozzles are coated with artificial or natural diamond particles. Products with diamond coating are chosen for pedicure, buffer treatment, while artificial products are used for removing gel coatings. These are inexpensive products that are suitable for beginners.
- Silicone, felt, suede. Pads made of these materials are polishing and are used in the final stage to grind the nail surface.
Beginners should have the following nozzles in their arsenal:
- Cylinder Drum. Such a cutter, because of its structure, can easily replace other products.
- Needle-needle nozzle. a product with a diameter of 1.2 to 1.8 mm, every master must have. It will help to get under the side rollers.
- The corundum cutter with low grinding properties or the silicone cap are universal products for smoothing the nail and cuticle.
- Cone with a pointed tip. Handy tool, helps you on rollers.
- “Corn” is a ceramic nozzle with small indentations for grinding out unnatural materials and sanding rough skin rollers.
Recommended articles on the subject:
- Diamond ball cutter. It is difficult for beginners to work with this product, as it often grabs the nail bit when sanding the cuticle. This cutter has different types of abrasiveness. The working surface is represented by the following diameters: 23 mm, 25 mm, 27 mm, 31 mm or 33 mm.
Products with a small tip size are best for hard, dry cuticles. The largest size is used for the final grinding of the skin. Manicurist selects the nozzle that is suitable for working with a particular client.
- Ceramic product “corn” with large grooves. If the power of manicure power tool is not enough, the nozzle begins to vibrate, get hot and damage the nail surface. Buy a ceramic cutter for manicure can be about 1 000.
The hardness of ceramic cutters for manicures
Abrasivity is the hardness of the mill, which allows it to grind, erase the surface with which it comes into contact. Its level depends on the diameter of grains that cover the surface of the product. This is also the reason for the use of the device: the nail, skin, non-natural material.
The size of grains and hardness of the nozzle can be determined by the color of the bands at the diamond or ceramic cutters for hardware manicure.
- The black color indicates a very rough material. Mega-hard products have two belts. Such nozzles are designed for grinding down built-up nail plates, but not for the treatment of natural nails and skin. Only professionals use these tools.
- The green color indicates a surface covered with coarse particles. This ceramic tip is used for grinding down artificial surfaces, hard skin on the feet and hands.
- The blue color of the band and the medium particle diameter of the nozzle allow you to work with cuticle and rollers. This is the most common degree of abrasion.
- Red indicates a coating with fine grit. Such ceramic products can be applied to the natural nail and skin surface.
- The yellow band indicates a surface finish with very fine particles, which gives the tool the lowest grinding ability. These products are used in nail and skin treatments.
- The white band indicates that the nozzle polishes the nail plate.
How to disinfect ceramic manicure cutters?
Ceramic cutters are disinfected in an ultrasonic bath with a special solution. To protect the cutter from the harmful effects of the device, you can put a special protective cap on it. After treatment with ultrasound the cutter is rinsed under running water and then air dried.
Ceramic cutters should be dried before being sent for sterilization. After soaking in a disinfecting solution, we recommend waiting approximately 5 hours and then placing the instrument in a desiccator. If an autoclave is used for sterilization, drying is not necessary.
What should not be placed in the dry-heat oven?
Buffs, interchangeable files, files not made of metal; sponges, absorbent cotton and wax products; other items not made of heat-resistant materials (cuticle sticks, plastic instruments, cloths and napkins); instruments in kraft bags for steam sterilization!
Cutter, the corundum crumbs on its surface are easily cleaned and disinfected. It can be cleaned under running water, then. in an ultrasonic cleaner. Any kind of solutions can be used for sterilization, hot cabinet can be used, corundum can withstand everything.
What is sterilized in an autoclave at 2 atmospheres?
132 degrees. 2.0 atm 20 minutes (for goods made of corrosion-resistant metal, glass, rubber). General surgical and special instruments, appliance parts, glass, dressing material, articles of rubber, latex and certain plastics are sterilized using the steam method.
Dry-heat apparatus (dry-heat chamber, air sterilizer) is an apparatus necessary for sterilization of instruments (mostly. medical) by means of hot air The essence of the dry-heat chamber. treatment that takes place by circulating heated air in a heat-resistant chamber.
How long to keep the instruments in Alaminol solution?
Alaminol for manicure tools is used in the form of a 5-8% solution, the preparation of which requires taking 50-80 ml of concentrate and add 950-920 ml of water, respectively. To disinfect the instruments, soak them in the solution for 60 minutes, paying attention to all accessories.
per 1 liter of water. That is, the solution must contain 1% Septolit-Tetra disinfectant. The soaking time for instruments at this concentration is always 15 minutes. Wash each instrument with a brush and soap (or detergent) under running water.