Cutting polypropylene pipes with a hacksaw for metal. How to cut a sewer pipe

How to cut polypropylene pipes without a pipeline

When laying pipes from polypropylene, you need to cut them into segments of the required length. A smooth cut without bullying material and sawdust significantly facilitates the subsequent work and quality of the joints received.

We have a smart people, it manages to adapt the most unimaginable tools and adaptations for cutting the material. But cutting with improvised tool is unable to provide the quality of the pipeline.

For this reason, you need to know what can be used for this and what is not worth it:

• Kryzuvka for metal;
• pipelines of different designs;
• self.shackle knife;
• band-saw;
• corner grinder;
• electrician;
• Scissors for plastic.

The use of a hacksaw for metal for metal is seriously considered, when working, the end becomes terry, there are burrs on it, which will have to be removed using sandpaper or knife. No matter how you do, the quality of the cut is bad. It is permissible to use it for single cuts. In the manufacture of a pipeline with many joints and turns, it is better to prepare a special tool.

Specialists use special scissors. Their sharp blade is placed on one side device. The second blade replaces the base with a special slot into which the cutting plate passes. When working with this tool, the hand gets tired, quickly cut a lot of material with them is very difficult. They cannot be cut thick pipes, the maximum diameter is not more than 42 mm.

When using a corner grinder, you need to prepare a disk for metal. When working, it is important to accurately distribute the effort. it is impossible to press hard on the corner grinder.

Electricity. the easiest way to work if there is no special pipeline. But the ability to make an uneven cut sharply increases, for this reason it is desirable to gradually turn the pipe during operation.

Which categorically cannot be used for cutting

Ribbon saw. the instrument disk is spinning very slowly for this work, and if the teeth of the saw are not acute enough, damage to the inside of the pipe is possible, this will cause cracks and chips.

Circular machine. polypropylene bends well. During pushing into the machine, there is a risk of bending the material, a blow is possible, which can lead to injuries of a working person.

A self.substituting knife (with cloves) is more difficult to work, the reason is that in the middle of the pipe there is a layer of aluminum. But if there is no other tool, you can prepare several segments.

The disadvantages of these methods are that when working, plastic begins to “shake”, parts of the material appear at the joints, they can subsequently get into the pipe and clog the filter during the operation of the system. And nobody needs it. To eliminate such shortcomings, use several additional tools.

• FACKOSARER. used to align the edge of the cut and as a result for the better quality of welding. It allows you to remove the edge or remove the upper part of the plastic along the diameter of the pipe;
• Calibrator. if during cutting you crushed the cut, and it became oval, this tool will allow you to level the end. For different diameters, you need to use your calibrator.

When planning the assembly of the pipeline from polypropylene pipes, you need to think over the process of work in advance and prepare the tool. The required set of tools is selected taking into account the complexity of the assembly, the diameter of the pipes and the size of the pipeline.

How to cut polypropylene pipes

We have already written about polypropylene pipes in this article. Personally, I consider these pipes, in fact, the most all.produced, therefore, as a pipe itself, well, and fittings, compounds, there are significant pennies for them. Because they are very all.widespread, I will try to tell about them as much as possible. And now an easy article, than cutting polypropylene pipes. It seems that the question is easy, but not many newcomers know about it ………

How to cut a pipe evenly? Overview of pipelines

Unlike iron and metal.plastic pipes that can be cut with a hacksaw for metal, polypropylene pipes are much softer. And cut them with a hacksaw for metal, this is excuse me for the expression. “pure perversion”. But if you have nothing under your hand, you can cut the metal with a hacksaw. In general, to be honest, you can cut such pipes with anything, even if with a knife, this is plastic. But there is a small minus, cutting polypropylene, let’s say a hacksaw for metal. The thing is that at the site of the cut, there will be a chip that remains in the pipe and will interfere with the water clock, and this is no longer excellent.

Therefore, in cutting polypropylene pipes, I advise you to use special scissors.

Scissors for cutting polypropylene, come complete with many soldiers of polypropylene pipes. The scissors have a special very sharp knife, which is located on top, also the lower holder, where the pipe lies.

Just mark the suitable pipe size, put in scissors and cut off the suitable pipe size. Everything is simple. It must be said that polypropylene is not at all difficult.

After such cutting, there are no burrs or crumbs, only a very smooth surface, you can immediately solder.

Cut polypropylene with scissors, if you don’t have them, then buy them, they are not expensive, 100. 400, but they are worth it.

Other tools for cutting plastic pipes

They are used occasionally when there is no pipeline under the hand:

• Corner grinder. for cutting pipes you will need a cutting disk for metal. The main point in the operation of a corner grinding is a clear regulation of effort, it is impossible to press the tool very much on the tool.
• Electricity is a more successful method in the absence of special scissors. There is a great opportunity to get a scythe, therefore, for greater accuracy during operation, the pipe needs to be turned a couple of times.

What is categorically not recommended to cut pipes:

• Ribbon saw. its blade moves very slowly and if it is not inseparable enough, the possibility of damage to the internal diameter of the pipe is great, which leads to chips and cracks.
• Circular machine. Since plastic pipes are flexible, pushing them into the machine often causes a pipe shift and blow, which is unsafe for a person producing a cut.

Scissor pipeline

Scissors are suitable for PVC not the thickness of the inch

PVC pipes scissors are inexpensive and easy to use. They are available in most household stores or centers for landscaping a house in the plumbing section. However, they are limited in their cutting ability and can add a load on their hands, since they are ideal for small pipes. Scissors for plastic pipes should only be used for PVC with a thickness of 1 inch or less.

How to cut metal.plastic pipes

Metal.plastic pipes have a number of advantages over their competitors. They are much easier than metal and much more resistant to oxidation than copper. They are easy to replace and easily give the necessary shape.

You can create a pipeline of any shape. Well, the main advantage is the cost. It is much lower than that of copper pipes. And the quality is at about the same level.

During operation, it may be necessary to cut the pipes. For this, a special tool is used, which is designed to work with a similar material.

To increase the efficiency of the procedure, it is recommended to properly prepare the pipe and tools before work. Consider the main features of metal.plastic pipes and how to cut them.

Preparation of the pipe and the required tool

As tools, a cutting device, measuring ribbons, divorce keys, seals and some other things are used as tools. All this should be in an accessible place at the time of work.

Sometimes it is required to clean the outer part of the reinforced coating in order to simplify the cutting process at the next stage. For stripping, a coupling with blades is used, which allows you to get a perfectly even cut and get rid of the polymer stratum. This is necessary for welding, which will most likely be carried out during the installation of the pipeline.

Important! When working, it is necessary to cut exactly as much material as it is necessary for the nozzle of fitting for metal.plastic products.

Tools for cutting metal.plastic pipes

In the process of cutting pipes, the following tools will come in handy:

It is important for the master to determine in advance how he will cut metal.plastic pipes. The most important tool on the list is scissors. Everything else is necessary for special preparatory work.

In the process of cutting, you do not need to apply a lot of effort. It is enough to fully control each movement. If you do not pay the control of proper attention, you can easily cut off the excess part.

If in the process of cutting it is necessary to bend the product, it is not recommended to do it with hands. So you can easily ruin the aluminum layer that is inside. It is better to take a professional pipes and perform an operation with its help.

The use of unsuitable tools when working with one site can affect the entire network as a whole, which will lead to large renovation costs.

Important! Special scissors are usually in a set for welding. But they can be purchased separately. The price of this tool is not so high as to save on it.

Before proceeding directly to cutting, it is necessary to very clearly measure the part where the unit will be separated. For this, a roulette or ruler is used, as well as a bright marker. A faded pencil can simply not be seen, especially if the room is not enough lighting. The mark can be made with a knife, leaving a scratch.

During operation, pieces of plastic and aluminum can fly in different directions. Therefore, it is necessary to use protective equipment in the form of glasses and special clothing.

How to cut polypropylene pipes

We have already written about polypropylene pipes in this article. Personally, I think these pipes are practically the most common, because the pipe itself, and the fittings, compounds, are significant pennies for them. Since they are very common, I will try to tell about them as much as possible. And today a light article than cutting polypropylene pipes. It seems that the question is easy, but not many newcomers know about it ………

Unlike metal and metal.plastic pipes that can be cut with a hacksaw for metal, polypropylene pipes are much softer. And cut them with a hacksaw for metal, this is excuse me for the expression. “pure perversion”. However, if you have nothing at hand, you can cut the metal with a hacksaw. In general, to be honest, you can cut such pipes with anything, at least with a knife, this is plastic. But there is a small minus, cutting polypropylene, let’s say a hacksaw for metal. The thing is that at the site of the cut, there will be a chip that will remain in the pipe and interfere with the water flow, and this is no longer good.

Therefore, in cutting polypropylene pipes, I advise you to use special scissors.

Scissors for cutting polypropylene, come complete with many soldiers of polypropylene pipes. The scissors have a special very sharp knife, which is located on top, as well as the lower holder, where the pipe lies.

Just mark the desired pipe size, put in scissors and cut off the desired pipe value. Everything is very simple. I must say polypropylene is very easy.

After such cutting, there are no burrs or crumbs, only a very flat surface, you can immediately solder.

Cut polypropylene with scissors, if you do not have them, then buy them, they are not expensive, 100. 400, but they are worth it.

Cutting pipes video

That’s all, I think, I helped you in this matter, read our construction site

How can you cut plastic pipes

When installing various pipelines, plastic pipes are increasingly replacing steel. This is facilitated by such factors as:

• A wide variety of products from various types of plastic;
• high resistance of plastic to corrosion and overgrowing the walls with lime coating;
• the ease of plastic pipes that greatly facilitates the installation of pipelines;
• the lower cost of plastic compared to metal pipes, significantly reducing the estimated cost of laying pipelines;
• Long service life.

Therefore, plastic pipes are universally used both in industrial and private housing construction.

Which tool can be used to cut plastic pipes

If we take into account that the people in our country are artisan, then for cutting pipes they manage to use the most unimaginable improvised means. But do not think that such a cut contributes to the good quality of the future pipeline. Therefore, we consider tools that allow the most qualitatively to cut plastic pipes:

• Kryzuvka for metal;
• self.locking knife (with small cloves);
• scissors for cutting pipes made of plastic;
• roller.type pipeline;
• battery pipeline;
• Guillotine pipeline.

Cutting pipes with a hacksaw for metal or knife should not be considered seriously, since their use leads to the fact that the end of the pipe is blinking, burrs that have to be eliminated with sandpaper or cleansing with a knife.

In any case, the quality of the cut suffers. These methods can be used for single cuts. If the pipeline has a complex configuration and many joints of individual sections, then these tools are better not to use. Pipe cutting scissors are used mainly for cutting pipes from plastic polymers.

The sharpened knife blade is fixed only on one side of the tool. At the site of the second blade there is a fairly wide base with a slot intended to receive a cutting plate. Work with such scissors is carried out exclusively due to the muscular strength of a person. A rounded rack is placed between the handles of the scissors, which, after closing the handles of the scissors, pushes the blade in the direction of the base. The pipe cutting process is as follows:

• On the surface of the pipes, they put a well.visible mark, putting the cut place with it;
• The base is located on top of this mark, controlling through the cut of the base its position;
• Then, having attached strength, they crash into the pipe and, gradually increasing the effort, produce the final cut of the pipe.

The advantages of scissors are quite high efficiency and cheapness of the structure. The disadvantage is the direct connection of the effectiveness of the work with the tool with the physical strength of the person working for them. In addition, during the cut, it is necessary to monitor the smooth movement of the brush, otherwise the blade can simply slip from the gear rack.

It is clear that with a large number of cuts the hand quickly gets tired, so the speed of work is reduced. In addition, it is impossible to cut large diameter pipes with scissors. The maximum diameter of the processed pipes is 42 mm.

The effectiveness of the pipeline is no worse than scissors. But, unlike them, here during work there are practically no physical efforts. The cutting process itself is as follows:

• At the site of the cut, a marker is placed;
• The screw is removed from the clamp, and the bracket is brought to the place of the cut;
• Then the screw is smoothly delayed (so that the pipe does not burst);
• After creating the necessary effort on the cutting video, the clamp begins to rotate around the pipe, smoothly twisting the tension screw.

Thus, a circular cut of the pipe is produced, while the end of the pipe is very flat, without burrs. The only danger during the operation of the pipeline is the appearance of cracks on the pipe due to too strong the pressure force of the screw.

Guillotine pipeline is used to work with pipes with a diameter of 63 to 350 mm. In this case, the probability of deformation or destruction of the walls of the pipe is reduced to almost zero. The cutting process is as follows:

• On the pipe, they mark the place of cut and insert it into the guillotine, securing from 30 to 60 degrees in the sector;
• A guillotine blade, which is installed on wheels;
• After the first incision of the plastic, the blade is immersed in the pipe using a rotating vinta handle and, thus, cut the pipe completely.

At the same time, the cut is very even, without burrs. Guillotine blades are easily replaced. In modern guillotin, the blades are additionally covered with Teflon.

Other tools for cutting plastic pipes

They are rarely used when there is no pipeline at hand:

• Corner grinder. for cutting pipes, a cutting disk for metal will be required. The main point in the operation of the corner grinder is the exact regulation of the effort, it is impossible to crush too much on the tool.
• Electricity is the most convenient way in the absence of special scissors. It is likely to get an oblique cut, so for greater accuracy during operation, the pipe must be turned several times.

Installation of the external sewage network

The external sewage system begins at the place of the pipe out of the structure (building), and ends with the arrangement of a septic tank or other device for cleaning and collecting masses.

• outline the location of the sewer pipeline on the site, indicating the location of the drainage well and septic tank;
• purchase all the required materials and pipes with a diameter of 110 mm, given that the minimum distance from the building to the place of gathering is at least 50 meters.

The laying of the outer sewer network is carried out according to the previously thought.out scheme

There are some rules for laying the external pipeline to which:

• digging a trench, a width of a slightly larger diameter of the pipe;
• device of a sand-gravel pillow at the bottom;
• additional laying of the geotextile layer (if necessary);
• Installation of viewing wells when changing the direction of the sewer pipeline, with significant height drops, on an even section after 6-12 meters.

After laying pipes, the trench is instilled in a similar sequence. It is advisable to avoid various bends or turns of the track to prevent the risk of blockages. If necessary, you can use auxiliary details: plugs, contours, crosses, wiring, tees, conclusions and others. It is necessary that the fittings are made of the same material as the main part of the pipeline.

How to cut the pipe along

Is it possible at home without special equipment to cut along with the smoothness of the PVC pipe with a diameter of 100 mm 3 m long ?

Комментарии и мнения владельцев of users:

In order to cut exactly the pipe along, they usually use special equipment called a bracelet with a slot.But as I understand it, you do not have such equipment and you want to cut the pipe at home.This can be done more evenly and carefully, but not everyone has such a tool at home.In this case, you can use the usual file.The cut thanks to the jigsaw and the file is quite even, but you will have to spend a lot of time on it.The fastest way is the use of corner grinders, but the cut may not be as smooth as you would like.

I understood the question like this: nothing, but how to cut. I did it like that you put the pipe in an even place, packed it on both sides (with several segments of a massive corner), it is desirable for the bars along the entire length so that the pipe does not spin about. You note by the eye of the top and a lace of soaked in ink you beat off a flat fishing line for a trimmer. You count the length of the circle, make a template from a rope along the length of half a circle you tie the cloves and Dapeie should be clear. From the already drawn braid fishing line, you mark several points on the other side. But cut anything, I am a jigsaw.

Output two points and through them pull the rope. In order for the trimmer fishing line to be clearly visible and not clogged with sawdust, glue paper tape. One of its edge on a stretched thread and on this edge will go a cut. You can cut it with a jigsaw, but if it is not, then with a canvas from a hacksaw for metal, wrapping the edge of the canvas with a rag or foam, to keep it more conveniently.

I have not tried this method yet, but I think you can do it like that. We take a sheet of paper A4, A3 depending on the length of the pipe, you can use the newspaper, it has a geometry is also not bad. Cut off the length of the pipeline circumference, draw a fishing line for a trimmer in the middle of the sheet and wrap up the pipe combining the edges of the sheet. Combined angles are points of the straight section, from the opposite side it is a point drawing a straight line. With this method of mowing fishing line, the axis of the pipe axis will be strictly parallel.

Take the pipe, take metal.Corner, larger or equal to the length of the pipe, fix the corner to the pipe and saw (the corner will not give the disk ‘walk’). Work in the same way with a sheet metal

Read How to cut a corrugated stainless pipe

Maybe someone will come in handy. I had to make a prefabricated pipe to the boiler in a greenhouse. Well, they cut off a piece in L-250 mm pipes, cut along the wall, expanded the cut place, welded a piece of L-250, h- equal to the optimal diameter, then welded to the main pipe, a pipe with a ‘skirt’ happened

Tools for cutting metal.plastic pipes

In the process of cutting pipes, the following tools will come in handy:

It is important for the master to determine in advance how he will cut metal.plastic pipes. The most important tool on the list is scissors. Everything else is necessary for special preparatory work.

In the process of cutting, you do not need to apply a lot of effort. It is enough to fully control each movement. If you do not pay the control of proper attention, you can easily cut off the excess part.

If in the process of cutting it is necessary to bend the product, it is not recommended to do it with hands. So you can easily ruin the aluminum layer that is inside. It is better to take a professional pipes and perform an operation with its help.

The use of unsuitable tools when working with one site can affect the entire network as a whole, which will lead to large renovation costs.

Important! Special scissors are usually in a set for welding. But they can be purchased separately. The price of this tool is not so high as to save on it.

Before proceeding directly to cutting, it is necessary to very clearly measure the part where the unit will be separated. For this, a roulette or ruler is used, as well as a bright marker. A faded pencil can simply not be seen, especially if the room is not enough lighting. The mark can be made with a knife, leaving a scratch.

During operation, pieces of plastic and aluminum can fly in different directions. Therefore, it is necessary to use protective equipment in the form of glasses and special clothing.

How to cut a profile pipe along or across: marking and cutting methods

In household households, profile pipes are widely used in the manufacture of greenhouses, greenhouses, canopies to protect automotive equipment from atmospheric precipitation and other designs. When working with this material, it is useful to know how to cut a profile pipe along the line or across with the most accurate angle.

Among the large number of construction cutting tools for metal, the leader in speed, simplicity of cutting and economy is an angle grinding machine (angular grinder), which is often present in the instrumental kit of any home master. To cut a profile steel pipe using a corner grinder, a regular metal disk will be required and strict compliance with safety rules. the destruction of the disk for segments at high speed of rotation can lead to serious injuries.

How to cut off the profile pipe across smoothly

Most often in the household, a rectangular or square trumpet metal is used with a wall thickness of not more than 3 mm, and cutting into separate segments is necessary when carrying out work on assembly welded frames.

To correctly cut the pipe, use additional devices to designate and mark the cut line, some of the devices perform the functions of the supporting face for the cutting disk.

Nuances of work with a rectangular section

Rectangular harvesters are much easier to cut along and down with any corners than cylindrical elements that are difficult to keep in a motionless state on a flat surface. The transverse circumcision of the blanks at any angle does not represent much difficulties. the fishing line for the trimmer of the desired angular slope is carried out on the lateral face and always coincides with the calculated (round elements require the use of special patterns calculated on the computer, to combine their faces at an angle other than direct).

The thickness of the walls of the metal profile when used in household farming rarely exceeds 5 mm. it is easy to cut using an angle grinding machine with any metal disk.

Which tool is used

As noted above, the main tool for cutting metal parts in domestic conditions is an angle.grinding machine, in its absence, you can use a hand hacksaw for metal or an electrician, which can also cut metal materials with a special canvas with a diamond coating.

For cutting corner grinders, cutting electric contest discs are used not intended for grinding operations. As an auxiliary tool, roulette, a metal ruler, various types of clamps, pencils and markers for applying marking will come in handy.

Pipe

The use of a paper sheet is a simple method of marking a rectangular or square profile for accurate circumcision at an angle of 90 or 45 degrees towards its axis.

To make markings for transverse cutting at an angle of 90 degrees, take a sheet of paper and wrap them with the pipe to the exact combination of the edges, after which they are glued. With this method, a fishing line for a cutting trimmer is very clearly visible, unlike it with a pencil or marker along the edge of the template.

After that, the profile is cut along the template edge alternately from all sides, trying to prevent complete cutting of the finish areas. this can lead to the blows of the disk on sharp corners and its destruction.

A sheet of paper can be placed on the side walls of the pipes of a rectangular or square section. To do this, the paper sheet is folded diagonally, and the resulting angle of 45 degrees is applied to the side walls and make the corresponding markup. In order for the side lines to be at the same level, the sharp angle is applied to the transverse line placed at an angle of 90 degrees to the axis, which is previously applied in the above way.

Pipe cutting

It is very convenient to cut a profile pipe using a special template, which is an analogue of a construction rod for cutting building materials at different angles.

To do this, the above or in another way make a metal template from a profile pipe cut along a piece, it can be designed to get a straight or angle of 45 degrees.

To cut the metal profile, a template is applied to it and drawing a fishing line for a trimmer, according to which then the cut is made. In other cases, the template is held and a corner grinding is held for a trimmer on the surface of the workpiece, trying to avoid strong pressing the side surface of the disk to the applied metal template. Then the template is removed and cutting is continued according to a well.noticeable depression on the faces of the workpiece.

Using the template, you can get a very flat fishing line for the trimmer of the cut, if you do not hold it manually, but fix it on the workpiece with a clamp or fastener bolts.

For the independent manufacture of fasteners in the side surface of the P-shaped platform, the hole is drilled and welded at this point on the outside the unit, into which the bolt is screwed.

To fix the template, put it to the cut part and screw it up, pressing the template surface to the workpiece, after an angular grinder with a metal disk, a cut is cut, slightly touching the guide edge.

High.quality cutting polypropylene pipes. How to cut polypropylene pipes? Types and features of tools, technology for cutting with precision scissors, recommendations of specialists

Due to the growth of popularity and prevalence of polypropylene pipes (propylene polymer) used to arrange water supply and other communications systems, the demand for a specialized tool that facilitates the work with the material has increased significantly.

Special, exceptional attention is in the right choice of a model of scissors cutting polypropylene pipe products. This greatly simplifies the preparation of the entire set of parts for the installation of wiring.

As a rule, direct segments (up to 12.0 m) are implemented on the market, although polypropylene pipes in the bays are often found, used to install a warm sex system.

All modifications of the equipment produced for cutting thermoplastic polymer propylene pipes are divided into several structural options.

Precision scissors-have a fairly simple, reliable crack-cutting mechanism. With this tool, you can dissect and fragment products with a diameter of 3.0–41.5 mm. The cutting tool has a steel blade (alloyed brand) with a jagged rail that allows you to perform quite light, even cuts of propylene pipes.

Using precision scissors, you can easily cope with one hand, however, with large volumes of fragmentation of the material, fatigue of the muscles of the hand, forearm and shoulder rapidly increase. Buying a tool involves the design of an annual guarantee that is valid only with the competent use of scissors.

The battery pipeline is an automatic tool for superbust (a maximum of 7.0 seconds), neat cutting of propylene pipes, medium thickness (8.0–29.5 cm). Compressive power of cutting surfaces provides a small, powerful electric motor.

Roller pipeline. convenient to work modification of the cutting polypropylers of the tool. Despite the uncomplicity of its design, the employee can perform an absolutely even cut. In this case, cutting of pipe elements is carried out at an even (90 degrees) angle.

Attention! Any retreat in the process of cutting from an even, right angle (90 degrees) can provoke a breakdown of the tool or deformation damage to the lines of the cutting!

Roller pipeline instruments are with telescopic elongation. Such tools are equipped with a ratchet and, in general, resemble ordinary scissors. This pipeline has, on the one hand, the C-Formen Walking, where the trimmed pipe is placed. The opposite side contains an acute cutting blade. It after closing the handles with a brush cuts off the pipe in a flat plane.

Guillotine pipeline device used to cut large diametral pipes (63.5–350.0 mm). The tool is characterized by the presence in the design of a high.strength, sharply bidden blade covered with Teflon. A flat installation of the pipe, as well as unhurried cutting with very sharp blades contribute to the maximum smoothness of the end surfaces. This greatly facilitates the implementation of subsequent electric welding without additional processing of pipe ends.

Recommendation! When there is no specialized tool for cutting pipes from polymer pipe, you can use a special hacksaw for metal or wood. It must be remembered that the slightest violation of such a technology can spoil the trimmed pipe. In addition, the end plane of the cut must be additionally cleaned from burrs and forming chips, and this takes a lot of effort and is spent extra time!

How to cut thin.walled pipes

When working with thin.walled rental, there is a high risk of crushing the edges of the saw. To avoid this, apply filling out the profile from the inside:

• When working with a hacksaw, a round wooden stick of suitable diameter is inserted
• When working, the corner grinder is filled with sand, crush it and plug it with traffic jams.

This allows you to maintain the original shape of the pipe and smoothly cut off the required length.

How to correctly solder polypropylene pipes.

Immediately before soldering pipes, you need to prepare all the necessary tools.

VO-1, you need to purchase or rent a special device (soldering iron) for heating the pipes before their docking.

The soldering iron consists of a tire (heating element), a stand in the form of legs and a handle with a control board, nozzles of various diameters. It works from the network.

Secondly, you need to have a roulette, special scissors for cutting pipes (usually they come with a soldering iron in a suitcase).

Soldering polypropylene pipes is carried out according to the subsequent principle:

It is installed on the stand, fasten the nozzles of suitable sizes, set the temperature of 260 º C. You need to wait for about 15 minutes so that the soldering iron is heated. When a reddish indicator goes out, you can start work;