Caterpillars
Snowmobile tracks can be made with your own hands using the following materials:
- conveyor belts;
- motorcycle chains;
- water pipes.
The speed of a homemade snowmobile can be about 60 km / h, so safety precautions must be observed while driving.
For light snowmobiles, a tiller is usually made from a conveyor belt and roller chain. To create such tracks, you do not need to have any skills or have specialized equipment.
To extend the life of the tape, its edges are stitched with fishing line. In this case, the step between the stitches should be equal to 1 cm. This will prevent the tape from loosening. To form a ring, the tape is sewn from the ends.
The choice of the thickness of the tape used depends on the capacity of the unit being created. The higher it is, the thicker the tape should be.
Diagram of the tracked unit of a homemade snowmobile
Track block diagram:
- made of steel bar, two ties with M8 nut (1);
- the drive sprocket of the tracked unit (2);
- track drive shaft (3);
- tensioner and roller (4 and 5);
- track, piece-piece made of rail (6);
- homemade frame spar (7);
- driven track shaft sprocket (8);
- support ski (9);
- a support ski suspension bracket made of a channel (10);
- bolts: M8 and M6 (11 and 12.13);
- brass guide (14);
- screw (15);
- the sole of the support ski (16);
- bearing housing fastening (17);
- idler roller axle (18).
Didn’t forget about remaking the caterpillar. The number of tracks was increased to 33 units, respectively, the distance between them was reduced to 38 mm. The dimensions of the tracks are 500x38x18 mm. To ensure the accuracy of the track links installation, a slipway template was assembled. This allowed to avoid distortions.
The front steering skis have also been redesigned. From above, they were reinforced with spars. Springs have been introduced into the ski suspension, which allows the snowmobile to go smoothly over the snow crust. This increased the lifespan of the skis and frame. A handle was attached to the body pillar for ease of pulling out a stuck snowmobile. For the same purpose, a similar handle was attached to the wads.
To protect the tie rods from damage in the event of a run over snow-covered stumps or other obstacles, a protective bumper was installed under the tie rods.
After stripping all external parts from rust and painting, the snowmobile got a pretty good look. Given its excellent driving characteristics, it has become an indispensable assistant in the winter season.
Chassis
One or two skis must be attached to the steering column using a swivel joint. Shock absorbers for the front suspension are best used ready-made, for example, from a motorcycle. You should also decide on the question of whether caterpillars will be used for movement, or whether it is planned to make a mini-snowmobile on cameras. Each of these types of drive has not only advantages but also disadvantages.
The wheeled unit is more maneuverable, but inferior to the tracked unit in cross-country ability. Tracks can be made from a variety of materials yourself, such as conveyor belts.
It is important to remember that they must be lightweight and strong while ensuring good contact between the tracks and the surface.
Snowmobile design
To correctly assemble an all-terrain vehicle from a tiller, you first need to depict it on the diagram. Typically, a structure consists of two parts: driven and driven. The first named part consists of the following elements:
The leading part consists of a power unit, drive and frame. After creating the drawing, you can start welding the frame. For greater strength, it is worth using pipes that are used to create frames for motorcycles. But you can also use products that are used for the construction of a water supply system. You can give the pipes the desired shape using a pipe bender.
To avoid mistakes when creating a frame, you should first fix the elements of the system with spot welding. Only then can the joints be welded with a continuous seam.
After creating the frame, brackets are welded to it, which are necessary to secure the engine, runners and seat.
Benefits of homemade snowmobiles
It is worth noting that when creating your own snowmobile, you can use parts from other devices, which reduces the cost of the unit being created. Homemade snowmobiles are used in almost any environment, so many refuse to buy ready-made structures. The video shows the work of the structure, which is most often created from a tiller.
Stages of assembling a snowmobile from a tiller
The most common option is light “karakats”, which are characterized by good cross-country ability, provided by large cameras. Such machines are created in several stages:
Frame making
Beforehand, it is worthwhile to study the drawings well. If you wish, you can make a mini-snow scooter of your own design, but many prefer ready-made solutions. For the manufacture of the frame, it is worth using iron pipes. To give them the desired shape in accordance with the drawing, you will need a pipe bender. When this work is completed, it is necessary to connect all the frame elements by welding.
The next step is to manufacture a subframe at the front of the main structure. It is here that the power plant and gearbox will be mounted, for example, from the Zhiguli. To solve this problem, a stand with holes for the motor is welded to the frame. The drive chain is installed in a special slot.
Snowmobile Track Making
Consider the process of making a caterpillar. Plastic water pipe 40 mm, cut to length 470 mm. They will be used to make blanks for lugs. Then each of them is sawn lengthwise into equal parts with a circular saw.
The lugs are attached with furniture bolts to the conveyor belt. When making a track, it is imperative to keep the lugs at the same distance. Otherwise, the drive sprocket teeth will “run over”, as a result of which the caterpillar will slip and slide off the rollers.
A jig was made to drill holes in the conveyor belt for the fastening bolts. To drill the holes, a wood drill was used with a special sharpening.
This jig allows you to simultaneously drill six holes in the conveyor belt to attach three track lugs. We also purchased leading sprockets (2 pcs), an inflatable rubber wheel (4 pcs), closed bearings 05 (2 pcs).
A turner made a bearing support and a track drive shaft. The snowmobile frame is self-made. For this, square pipes 25×25 mm were used. The articulated pivots of the steering wheel and skis are in the same plane and on the same mowing line, so a continuous steering rod without ball ends was used.
Ski turn sleeves are quite easy to make. A 3/4 inch water sleeve is welded onto the front cross member of the frame. Male threads are screwed there. To them I welded the bipod of the ski rack and tie rod. Angles are installed on the skis, which serve as an attachment to the pivot stand of the snowmobile. A metal undercut is made at the bottom to better control the snowmobile while driving on packed snow or crust.
Chain tension is adjusted by motor offset
The handling of the snowmobile is quite simple. To increase the engine speed, the throttle stick is used, which is located on the steering wheel. This engages an automatic centrifugal clutch, causing the snowmobile to move. Since the engine power is low, the speed of the snowmobile is 10-15 km / h. Therefore no brakes are provided. To stop, you must slow down the engine speed.
Tracks are available in any width. Choose what is more convenient to do: a narrow but long track, or a wide but short one. It is important to remember that a larger track will put more stress on the engine and make it more difficult to control the snowmobile. If the caterpillar is made small, then the car can fall through in deep snow.
The weight of the snowmobile with all parts is 76 kg. It includes: steering wheel and engine (25 kg), skis (5 kg), wheels with axles (9 kg), drive shaft (7 kg), caterpillar (9 kg), seat with racks (6 kg).
It is possible to reduce the weight of some parts. For this size of tracked snowmobile, the weight is quite satisfactory.
The best homemade products. a snowmobile from Tiller
When making a homemade snowmobile, they use tracks from other snowmobile machines, or homemade ones, assembled from scrap materials. After choosing a track, you need to decide what type of suspension to use. There are two main types to choose from: roller suspension and skid suspension.
Each of them has both advantages and disadvantages. After that, it is important to decide what layout the snowmobile will have. Usually, two steering skis are installed on the front of the snowmobile and a track block at the rear.
The engine can be installed in both the rear and the front of the snowmobile.
How to make a snowmobile from a tiller yourself
This snowmobile can be made in a few weekends at the dacha in the garage. At first glance, its design looks very simple. If we compare its cross-country ability in wet or loose snow, it will not yield to many industrial snowmobiles.
The creation of the snowmobile was based on the principle: the less weight and the larger the track size, the higher its passability on deep and loose snow. Therefore, the design will be as light as possible.
Making homemade products. a snowmobile from a tiller video and description
From the tiller, you can also use the reverse gear, centrifugal clutch, steering and fuel tank. Next, you need to think about the propulsion of the snowmobile. Most of them are equipped with a caterpillar drive.
How to make a homemade snowmobile from a tiller on tracks
Four wheels are installed inside the track. When there is movement, they roll along the conveyor belt, with the lugs fixed. The track is driven by a chain from the motor, special drive sprockets, through the driven shaft. They were removed from Buran.
The engine is taken from a conventional tiller, which has a power of 6 hp. You can’t accelerate quickly on it. The soft suspension of the ski and track has been removed because the snowmobile is designed to ride on loose snow. This simplifies the design and reduces the weight of the snowmobile.
Characteristics of the resulting homemade snowmobile
frame length 2000 mm;
track width 470 mm;
between the axial distance of the support rollers 1070 mm.
Snowmobile from Tiller on tires
Another economical option for making a diesel snowmobile from a tiller and tracks. Motonart on tires from the MTZ-80 or Belarus tractor can easily move in the snow. This design is equipped with two additional wheels and pieces of metal pipe. Consider the benefits of such a snowmobile:
- efficiency. cheap or used materials are used here: wheels from a VAZ car, a square tube, used tractor tires;
- the ability to make a car at home using a welding machine, angle grinder, drill, knife;
- high maneuverability of the resulting snowmobile, which has the ability to turn like a tank in one place;
- good cross-country ability in deep and viscous snow;
- active brake right or left track.
In order to make tracks, you need two tires from a tractor, used ones are quite suitable. Side parts are cut from each tire with an electric jigsaw or just a sharpened knife. The structure is made of a square tube and two additional wheels. It is required to securely fix the tiller and the structure with wheels. Then the caterpillar obtained from the tire is sequentially pulled onto the front wheels, then onto the rear wheels. It turns out a diesel snowmobile on a caterpillar track, that is, on tires. In order to make it more comfortable, you can fit a small seat, which will not weigh down the structure. Otherwise, you will have to stand up to overcome the snowy expanses.
Fans of outdoor activities, hunting and fishing will appreciate the homemade snowmobile. The advantage of this incredible device will be high traffic at a low cost.
How to make a snowmobile from a tiller?
- What it is?
- Self-production
- Tiller snowmobile on wheels
- Snowmobile from tiller on tracks
- Snowmobile from Tiller on tires
- Safe driving advice
What it is?
A snowmobile is a power-driven vehicle. The most famous are small-sized models equipped with track skis and controlled by the principle of motorcycle. However, in fact, there are many varieties of all-terrain vehicles on low-pressure pneumatics and caterpillar tracks, snowmobiles. Tillers are also divided into wheeled and tracked. You can make a snowmobile from a tiller with your own hands with any chassis, only in this case, different methods and materials are used.
Self-production
Let’s consider step by step how to make different types of snowmobiles with your own hands.
Tiller snowmobile on wheels
To turn a wheeled tiller into a snowmobile, you need to take:
- an iron connecting structure-trailer;
- wheels for winter use, able to overcome snow obstacles.
homemade twin track go kart II
A strict condition for the whole idea is that the trailer must be rigidly coupled to the snowmobile frame. A metal channel with a length of about half a meter must be welded parallel to the axis of the snowmobile. To do this, two holes are drilled at the edges of the channel. Hole clamps on the edges provide additional fastening and structural rigidity. They are attached to the axle of the snowmobile with bolts with a lock nut, using a cross welded to the structure.
This mount will act as a stopper that holds the trailer in place, preventing it from shifting at an angle. Such an element, although it reduces the ability to maneuver on the snowmobile, makes it more stable. Thus, a two-wheeled mechanism on one axle can be easily converted into a stable four-wheeled vehicle. At the same time, you will not need any diagrams and drawings, or additional costs.
A snow scooter with a motor will also require the correct selection of wheels. The easiest option is to purchase them in a retail network for a winter purpose, but it is not always advisable to look for easy ways. A more economical solution would be to make the wheels yourself. The budget option is to equip the snowmobile module with cameras designed for trucks. Deflated cameras are put on each wheel and fixed over the chain for driving on snow and ice. One is not enough, you need about five. An inflated chamber in a cache of chains will be an ellipse with a surface divided into segments like a daisy.
Another option for using ingenuity and saving the family budget is to use metal hoops over the cameras. They should be wide enough, twice as wide as the snowmobile wheels. The diameter of the hoop must match the inflated wheels of the tiller and trailer. Several metal plates are welded on the inside of each hoop. The thickness of the plates must be made about 2-3 cm. After lowering the cameras, you should put hoops on the wheels of the snowmobile and pump them up again. The inflated chambers will squeeze as much as possible against the metal circles. Plates like dirt lugs help increase traction on snowy roads.
Snowmobile from tiller on tracks
a crawler-mounted tiller is a little more difficult, but possible, to convert to a snowmobile. Using the tiller motor, you can make a structure with great stability and passability. For this, the frame and transmission are mounted. Make sure the engine has enough power, you need a tiller of at least 6 horsepower. To make a snow motonart with an engine, you need to use:
- reducer;
- fuel tank;
- steering;
- centrifugal clutch.
It’s good if you have tracks from other snowmobile machines in your household stock. If not, then do not give up. It is quite possible to assemble the caterpillars on your own, using improvised tools and materials.
Next, you need to decide on the location of the engine: front or rear. Try to keep the structure as light as possible and the ski suspension to be soft. All this will make it possible to achieve high cross-country ability in deep snow. The principle is as follows: inside the caterpillar, when driving, 4 wheels roll along the conveyor belt. Special soil hooks are attached to the tracks to enhance traction. Caterpillars can be made at your discretion, but you should carefully consider the dimensions.
Wide or too long tracks will unnecessarily stress the engine. This, in turn, will complicate the handling of the snowmobile on tracks in the snow. A track that is too small will not be able to support the weight of the entire structure with the driver. It will become unstable and sink into loose and deep snow. For the manufacture of tracks, the simplest materials are used: plastic or plastic pipe of small diameter, wheels, bearings.
Workpieces with a length of 0.5 cm are made from the pipe, from which ground hooks are obtained. They are attached to the tape at the same distance from each other. Then they are bolted into the holes on the conveyor belt. The frame is made using square pipes or a channel. Use a tie rod without ball ends, as the steering and ski axes lie in the same plane.
On the front of the frame, bushings are attached to allow the ski to turn. They can be made from steel couplings with small diameter nipples and threads. Racks of skis and tie rods are welded to the pipes. To control the snowmobile, corners with a metal undercut are attached to the skis, which will allow you to move on ice or snow crust.
The weight of such a snowmobile is no more than 100 kg, and it is very simple to operate the vehicle. Since the power of the motor is low, the speed does not exceed 10-15 km / h, so no brakes are provided. The end of the movement occurs due to the reset of engine speed or the so-called engine braking.
Safe driving advice
Do not forget that any vehicle, even one made by yourself, requires attention and care. You cannot overestimate your capabilities and move in the dark or in bad weather conditions. If visibility is poor, you may not notice changes in the topography of the earth, holes, ditches covered with snow. The low stability of the snowmobile when hitting any obstacle (stones, stumps, metal objects) can lead to overturning, throw off the rider and / or press down with its mass, cause injury, or even death.
Care is required when overcoming slopes and when driving under any overhanging obstacles: sagging wires, stretch marks, fallen trees. The blow will hit the rider’s chest, so if there is a backrest, injury is inevitable. Be aware of possible road obstacles and take safety seriously.
For how to make a snowmobile from a tiller with your own hands, see the next video.
Homemade all-terrain vehicle snowmobile from Tiller
The simplest homemade all-terrain vehicle is a snowmobile made from an ordinary tiller: a photo and a detailed description of how to make a homemade product.
As you know, the tiller is used for processing vegetable gardens: plowing, cultivation, hilling and other work. But craftsmen have come up with another application of this technique. this is an alteration into a homemade all-terrain vehicle-snowmobile. As a result, you can make excellent transport for off-road travel.
The process of converting a tiller into an all-terrain vehicle is as follows:
To increase the tiller’s cross-country ability, the first step is to replace its standard wheels with larger wheels, for example, put disks and tires from the car. Then the wheels need to be wrapped with tracks from the snowmobile. To do this, the caterpillar is cut along the circumference of the wheel and pulled over the wheel, the edges of the caterpillar must be connected with powerful brackets or bolted connections. The tracks can be made homemade from the conveyor belt, and the tracks can be cut from a metal corner and bolted to the belt.
After such alteration, it is enough to attach a sled or a trailer adapter to the tiller, and the all-terrain vehicle is ready for the snowmobile.!
Homemade all-terrain vehicle from a tiller, confidently moves on shallow snow and ice. Good cross-country ability is provided by large wheels and track protectors.
How to make a snowmobile from a tiller on a goose
Diagram of the drive units and frame of a homemade snowmobile from a tiller:
- homemade frame (1);
- a second intermediate shaft sprocket with 17 teeth (2);
- intermediate shaft (3);
- first countershaft sprocket, 21 teeth (4);
- driven track shaft sprocket, 37 teeth (5);
- track sprocket, 8 teeth (6); the drive shaft of the caterpillar (7);
- two racks of the support ski, made of steel pipe 32×4 (8);
- two track idlers (9);
- the axle of the idler rollers made of steel pipe (10);
- hitch (11); tensioner (12);
- four drum flanges made of sheet steel (13);
- four flanges of the track sprocket made of sheet steel (14);
- steering puff (15).
To place the engine with a subframe in the center of the front of the frame, a platform was welded there, in which holes were prepared for the “legs” of the subframe. Similar holes are made in the traverse. The holes in the “legs” of the subframe have been redesigned into longitudinal slots to tighten the drive chain when the engine is moved.
The saddle frame has also been redesigned and moved back a little. Thanks to this, the engine is started at the handle. A big plus was the presence of forced cooling on the tiller engine. I used this to direct the air heated to cool the engine to the carburetor. The gas tank was also moved to the back. It is installed there on racks in the corner, for supplying gasoline to the carburetor by gravity along a long hose.
By moving the engine to the center of the machine, stability is improved. Thanks to this, the track of the steering skis was reduced to 950 mm, which led to improved maneuverability of the snowmobile.
After the countershaft was installed, the angular velocity was reduced due to the increased torque. The speed of the snowmobile was slightly reduced, but the traction characteristics were significantly increased. The snowmobile is now able to carry two riders with a load and pull a light sled with a load. Also, the drive sprockets of the caterpillar propeller were replaced with the same smaller diameter.
DIY tracked snowmobile from a tiller
To make a caterpillar snowmobile from a tiller, simple materials are used with your own hands. The frame is made of stamped channels and square tubes. Round water and gas pipes are used for the manufacture of shafts. The engine used from the Tiller “Neva”.
The snowmobile looked a little rough. But after carrying out winter tests, good driving characteristics were revealed: speed, cross-country ability. It is also lightweight and compact, and quite economical in terms of fuel consumption. The original design assumed an asymmetrical engine layout. This gave a number of advantages: during service. good access to the engine; convenient starting and gear shifting; redirecting the chain drive directly to the drive shaft of the track.
But during tests, when moving on loose snow, when a turn was made, the snowmobile often fell over. Because of this circumstance, it was decided to place the engine in the center of the front of the snowmobile. The design has been improved, and primarily the front end of the frame. An intermediate shaft was also installed, which transmitted torque from the engine to the track. In addition, a modernization was carried out, which improved the driving performance, comfort and reliability of the snowmobile.
Diagram of the steering rack of a snowmobile from a tiller
- Steering rack diagram:
- front frame traverse (1);
- a rack made of steel pipe (2);
- made of a corner 25×25 steering wheel support (3);
- steering shaft made of steel tube (4);
- crossbar made of steel pipe 28×28 (5);
- bipod (6); bronze washer (7);
- support sleeve with angle (8);
- nut, type М10 (9).
It was this slight improvement that led to the improved flotation of the snowmobile. The sprocket has risen above the support ski. As a result, the caterpillar reaches the upper layers of snow much more easily, and bumps, sastrugs, etc. are more confidently overcome.
Schematic of the intermediate shaft assembly of a snowmobile from a tiller
Intermediate shaft assembly diagram:
- steel seat support (1);
- frame cross member made of steel tube 28×28 (2);
- rack made of steel pipe 18×18 (3);
- traverse made of 45×25 corner (4);
- jib made of steel plate 40×5 (5);
- two bearings 204 in the housing (6);
- steel intermediate shaft made from pipe 27×3 (7);
- first sprocket with 21 teeth (8);
- frame spar (9);
- second sprocket with 17 teeth (10);
- rubber boot (11).
Inspection of the snowmobile prior to the upgrade revealed frequent bouncing of the sprocket teeth onto the wooden track. Therefore, it was decided to cut all the teeth, making them rollers. After modernization, the track transitions from ski to rollers smoothly, quietly and without cracking. The tensioning mechanism has also been improved: now it has become a screw.
Homemade snowmobile from tiller on goose bumps
Diagram of the tracked unit of a homemade snowmobile
Track block diagram:
- made of steel bar, two ties with M8 nut (1);
- the drive sprocket of the tracked unit (2);
- track drive shaft (3);
- tensioner and roller (4 and 5);
- track, piece-piece made of rail (6);
- homemade frame spar (7);
- driven track shaft sprocket (8);
- support ski (9);
- a support ski suspension bracket made of a channel (10);
- bolts: M8 and M6 (11 and 12.13);
- brass guide (14);
- screw (15);
- the sole of the support ski (16);
- bearing housing fastening (17);
- idler roller axle (18).
Didn’t forget about remaking the caterpillar. The number of tracks was increased to 33 units, respectively, the distance between them was reduced to 38 mm. The dimensions of the tracks are 500x38x18 mm. To ensure the accuracy of the track links installation, a slipway template was assembled. This allowed to avoid distortions.
The front steering skis have also been redesigned. From above, they were reinforced with spars. Springs have been introduced into the ski suspension, which allows the snowmobile to go smoothly over the snow crust. This increased the lifespan of the skis and frame. A handle was attached to the body pillar for ease of pulling out a stuck snowmobile. For the same purpose, a similar handle was attached to the wads.
To protect the tie rods from damage in the event of a run over snow-covered stumps or other obstacles, a protective bumper was installed under the tie rods.
After stripping all external parts from rust and painting, the snowmobile got a pretty good look. Given its excellent driving characteristics, it has become an indispensable assistant in the winter season.
Snowmobile design
To correctly assemble an all-terrain vehicle from a tiller, you first need to depict it on the diagram. Typically, a structure consists of two parts: driven and driven. The first named part consists of the following elements:
- shock absorbers
- steering column;
- runners.
The leading part consists of a power unit, drive and frame. After creating the drawing, you can start welding the frame. For greater strength, it is worth using pipes that are used to create frames for motorcycles. But you can also use products that are used for the construction of a water supply system. You can give the pipes the desired shape using a pipe bender.
To avoid mistakes when creating a frame, you should first fix the elements of the system with spot welding. Only then can the joints be welded with a continuous seam.
After creating the frame, brackets are welded to it, which are necessary to secure the engine, runners and seat.
What powertrain is required to create a snowmobile
Most often, craftsmen use a unit that is installed on the Tiller Neva. It is a four-stroke gasoline engine with one cylinder. This device has air cooling. Such a motor is lightweight and has a manual start system. Repair of such a device can be carried out even by a person who has minimal knowledge of engine operation.
Using the described motor, you can make a good working snowmobile that can be used for driving on snowy ground. If you decide to purchase a tiller, including for creating an all-terrain vehicle, you should think about the type of engine. Gasoline and diesel units have their own advantages and disadvantages.
For all-terrain vehicles, motors from Chinese chillers are usually used, since they are low cost and at the same time easy to maintain. Before starting to create an all-terrain vehicle, it is worth remembering that the chassis is best done with independent wheel suspension. This will ensure the comfort of movement.
If a tracked all-terrain vehicle is being created, the frame must be solid, and when designing a wheeled version, it is necessary to create an articulated structure.
Stages of assembling a snowmobile from a tiller
The most common option is light “karakats”, which are characterized by good cross-country ability, provided by large cameras. Such machines are created in several stages:
- The choice of the basis for the all-terrain vehicle. Usually, a frame from a Ural or Izh motorcycle is chosen as the basis. It is worth noting that the cars created on the basis of the Izh motorcycle are more maneuverable. Machines created using such frames are distinguished by good cross-country ability on various types of soil, as well as on deep snow.
- Creation of suspension and rear axle of a snowmobile. In order to make an independent rear and front suspension, it is necessary to connect the side members with a strut and a steering bush. This suspension ensures a smooth ride.
- Installation of wheels. ATVs usually use cameras from a truck. They are attached to the suspension through the hub. Such wheels provide ease of control of the all-terrain vehicle and the safety of its use.
- Installing the engine. After the suspension with wheels is installed, you can start securing the engine. After complete assembly, the car should be tested at low speed.
DIY snowmobile from tiller
The best vehicle for driving on snowy roads or fields is a snowmobile. But many of these designs are expensive, so you can often see a snowmobile that is built from a tiller. It is worth remembering that such a design can be made only with certain skills.
Skids and engine
Wide skis are used as runners, which are attached to the steering column using a swivel joint. For the front suspension, use motorcycle shock absorbers.
The engine is mounted on the leading part of a homemade snowmobile. In this case, before installing the engine, you must decide what to use. wheels or tracks. Each of these options has advantages and disadvantages.
If wheels are installed, the all-terrain vehicle from the tiller will be more maneuverable. If you make tracks, the cross-country ability of the snowmobile increases, but at the same time it becomes heavier.
Caterpillars
Snowmobile tracks can be made with your own hands using the following materials:
- conveyor belts;
- motorcycle chains;
- water pipes.
The speed of a homemade snowmobile can be about 60 km / h, so safety precautions must be observed while driving.
For light snowmobiles, a tiller is usually made from a conveyor belt and roller chain. To create such tracks, you do not need to have any skills or have specialized equipment.
To extend the life of the tape, its edges are stitched with fishing line. In this case, the step between the stitches should be equal to 1 cm. This will prevent the tape from loosening. To form a ring, the tape is sewn from the ends.
The choice of the thickness of the tape used depends on the capacity of the unit being created. The higher it is, the thicker the tape should be.
Amazing Homemade Invensions �� DIY Snowmobile 2017
How a Tiller Converts to a Snowmobile
It is the tiller that is taken as the basis of the snowmobile, since many site owners have this unit. At the same time, tillers are usually not used in winter. Having built a simple snowmobile, you can install a tiller engine on it, which can be returned back after the end of winter.
Created snowmobiles usually have a power of about 7 hp, which allows you to carry two people with a small load.
In order to assemble an all-terrain vehicle from a tiller with your own hands, you must have the following main parts and tools:
- welding machine;
- engine;
- pipe bender.
You will also need additional details, which you can learn about in more detailed consideration of the design of the snowmobile. Before making a snowmobile, it is worth drawing up a detailed drawing.
How to choose an engine
In order to create a snowmobile, it is necessary to consider the most important and central part of the entire mechanism. the motor. The motor must have a decent amount of traction to move the entire machine in tough snowy conditions. To make everything work out as needed, a powerful motor from Tiller Neva will do.
With such an engine, one or two people will be able to move around on a homemade snowmobile from a tiller with their own hands. Engine power has 6-7 horsepower, which is quite enough for moving on snow.
If you add a snowmobile stand to the tiller, the load capacity increases and you can easily load your tiller for snow rides.
Why is this engine good, many people ask. In fact, there are many more advantages than one might think:
- First of all, this is a democratic cost.
- Good quality is also proven by Japanese production.
- The motor has an additional air cooling system.
Also note that gasoline can be used as fuel.
A do-it-yourself snowmobile from a tiller. the best home-made devices and mechanisms. 110 photos and videos of the construction of a snowmobile
In modern times, few gardeners and gardeners do without a tiller. In warm weather, this technique is very often and densely used in ordinary daily affairs and never stands idle. But in the winter period, it is difficult for a tiller to find an application, and this suggests that the car will simply stand idle.
Home remodeling masters have come up with a use for the tiller and in the cold. I don’t want to move through the snow on my own, especially since in some places the snow reaches impassable volumes.
That is why a snowmobile is made from a tiller for the winter. This is a benefit both for the owner and for the equipment itself, since the tiller does not stand idle.
In the photo of a snowmobile from a tiller made with your own hands, you can clearly see that everyone makes such a model as he wants. For those who decided to create such a useful unit, you will need to choose which option is closer to him.
In this article, we will cover some important points for creating a snowmobile.
Summary of the review:
- How to choose an engine
- Features of the constructive plan
- How to decide on a move option
- Do-it-yourself photo of a snowmobile from a tiller
Features of the constructive plan
The simplest version of a snowmobile consists of a part that leads and one that is driven first. The second part consists of a seat, shock absorbers, a steering part and runners, thanks to which this part moves. The second part is much more complicated, since it contains all the elements that set the snowmobile in motion.
First of all, in the second part, it is necessary to correctly provide for the power unit, that is, the motor itself. The frame on which everything will be equipped and the drive is also important.
Diagrams and drawings of a snowmobile from a tiller with your own hands must be done in advance, and you can find the necessary option on the network or in various kinds of literature.
To begin with, before drawing up a drawing, determine the purpose for which the snowmobile will be used. After the drawings, you will need to select parts, and, if possible, do some with your own hands.