Echo benzotrimmer stalls on a cold. • CIMFLOK.COM

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate may form on the day of the gas tank, which is due to which the tasks with the operation of the device appear.
Excessive swing of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
Knives are removed from the car. some models will not work under this condition.
Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
To clean the tool, you should use kerosene, solvent, or other washing tools.
You can not clean a hot tool. it must cool before washing.
It is important to observe the recommended working mode. this will avoid overheating of the engine.
If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

completely drain the fuel;
disassemble the lawn mower, wash and clean all available components;

inspect the condition of the parts, eliminate all defects that can be corrected;
pour the required amount of oil into the gearbox;
Clean the air filter;
perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

How to get a motorcycle stihl

The main stages are how to get a STIHL motorcycle:

Before the operation of a gasoline trimmer for the grass, you should familiarize yourself with the instructions and check the trimmer for STIHL grass for each spare part. After you can collect it.
An important step is fuel preparation and refueling. You need to prepare the mixture in a measured container. Gasoline and oil are poured into it in the indicated ratio. Using a funnel, the mixture shimmers into the fuel tank.
At the first launch, turn on the ignition without opening the air damper. Put the device on an even and smooth surface for stability. Now. you need to sharply pull the cord from 3 to 5 times. Air damper can be opened in any case: the engine has started or not.

The first launch may require up to 15 jerks. After starting the engine, it is worth turning on idle for warming up. After a while, it is stopped by the button.

note! This instruction is universal, since in order to start the Stihl law trammer, you need to perform similar actions.

In the case of the launch of an electric trimmer for the grass, everything is much easier: you need to familiarize yourself with the instructions and act in accordance with it. Instead of fuel here electricity. The device works from the network, so it is important to provide sufficient power so that the trimmer for grass can gain speed.

After each operation, both gasoline and electric trimmer requires a thorough inspection.

Following the instructions, you can quickly eliminate any small breakdown on your own. But sometimes it is not possible to start the unit with your own hands. In this case, it is better to seek professional help, especially if this applies to the problem with the engine and the development of revolutions of the trimmer for grass or lawn mower.

In this article we will consider the problem why the lawn mower stalls and how to deal with this problem.

Even very good motorcycles may have problems with the launch. For example, it starts and stalls. Most likely, this indicates problems with filters. air or fuel. If it stalls at idle, then, most likely, the motorcosa has problems with the carburetor, which is too fast overheated and no longer copes with the formation of a qualitatively air fuel mixture.

If a trimmer for grass stalls when you press gas, t.e., когда двигатель начинает работать на больших оборотах, то это свидетельствует о проблемах с карбюратором или с топливным фильтром.

Motokos with an air filter will be evidenced by the fact that it ceases to work when opening an air damper.

Note that the Well Part online store offers you for the widest assortment and at the best prices.

What to do if the lawn mower starts and stalls?

Now we will consider all the above problems described in more detail.

In principle, the reasons why the engine of motorcycles stops working when pressing gas can be a huge number. Here we will consider only the most common.

Perhaps the air damper just clogged. And to eliminate the problem, it will be enough to simply clean the air damper. The engine also stalls due to the clogged air filter. To clean it, the filter should first be washed in the solvent, and then blow the stream of compressed air.

A similar procedure should be carried out with the clogged fuel filter, which prevents the intake of the fuel in the proper volume with an increase in engine speed.

The engine can stall for other reasons. Firstly, the spacer is worn between the cylinder and the carburetor, and secondly, the crankshaft oil seals began to suck in air.

We have already indicated that in this case the problem is in the carburetor. In it, due to increased temperatures, gasoline begins to boil, which is why the air-fuel mixture ceases to form or its quality is critically reduced.

In addition, this problem may arise due to the fact that the carburetor is equipped with a rotary rather than a disk damper. If the problem has acquired a chronic character, then it should be solved radically. by buying a new carburetor with a disk barrier.

Most likely, access to the fuel tank is difficult or completely absent, which is why a reduced pressure zone is formed in it, due to which the engine stops receiving fuel in the required amount and because of this you stop working.

The engine at idle can stall for the following reasons:

News ONENEN ONENEN ONENY ONENY ONE ONE ONE

LSI and began to prepare not quite normal gasoline solution, which is why they began to fall on the drum;

You will need spare parts to eliminate most problems, and the Well Part will be ready to provide them with the best cost to you.

Why stall the engine of a trimmer for grass when recruiting

The most popular with summer residents, gardeners and gardeners trimmers for grass are equipped with two.stroke engines operating on gasoline. In recent years, part of the manufacturers have been promoting motorcycles and leaflets based on four.stroke engines in the market, but they have not yet gained the popularity that two.stroke. They are more difficult in the device, more demanding on the mode of operation, purity of fuel, oil quality. Also, four.stroke engines are more in weight and more slowly gaining momentum.

During the operation of trimmers on the basis of two.stroke engines, a number of characteristic malfunctions arise related to the features of the design of the engines. With all the perfection of the Husqvarna or Echo engines, even they occasionally “acting up”. The budget models of motorcycle assembled in China, problems arise more often. This is due to both the lower quality of materials and the assembly level. The most characteristic malfunction is a poor launch from a “hot” state and “subsidence” of revolutions at a slight load. But sometimes a trimmer for grass stalls with a sharp press on the throttle key. Why does this happen?

The reasons for the breakdown

For all the apparent simplicity, the lawn mower is a well.thought.out and balanced tool in which each part is in its place. If everything is regular, the engine from the cold state should start after the first starter jerk. Depending on the model, first you need to swing the fuel mixture by pressing the transparent button on the carburetor. In a number of modern fuel pumping models, it is not required.

You also need to transfer the lever on the carburetor to the extreme position to close the air damper. In some models of Husqvarna and other manufacturers, the shuttle of the damper is carried out by turning a special regulator. After that, you need to turn on the ignition on the handle and energetically pull the starter’s cord, while pressing the gas key to about half.

The engine should start after the first jerk, but can earn after 3. 4 movements. This cannot be considered a breakdown. it all depends on the production of the motor, the quality of the fuel mixture, temperature and humidity and other factors. Two.stroke engines have their own character, to find out why they are not launched from the first, but from the fourth time, it is difficult even for professional mechanics.

If the engine confidently launched and earned, but the trimmer for the grass stalls when pressing the gas, then you forgot to transfer the carburetor lever to the position of the open or partially open air damper. Usually. this is the movement of the lever down. It may happen that the most stable the lawn mower works with a not fully opened damper. If you have used the trimmer for more than one season, so it will be. When the lever of the damper is transferred to the extreme lower position, the fuel mixture can become too impoverished and the trimmer for the grass stalls when you give gas.

This feature is not considered a malfunction. you just need to check the work of the trimmer for grass in different modes and try to use the optimal one in work. But there are other reasons why the lawn mower can stall at any stage, immediately after starting or during operation.

Other possible reasons

If, with a sharp addition of revolutions, the engine stalls, as if zabulae, then the reason may be:

Carburetor adjustment failure. This happens after prolonged downtime or after excessive loads, for example, natives in hot weather or in conditions of strong dustiness.
Clogging valve on the tank cover. Eliminated by replacing the lid or cleaning valve.
Weakening of the cable of the carburetor regulator drive.
Stretching of the fuel hose.
Depressurization of traffic jams on the tank, which includes hoses.
The clogging of the sapun.

When looking for the reasons why the trimmer stalls for the grass when trying to increase speed, other reasons may appear, for example, associated with the ignition coil and candle. If the fuel mixture is not prepared according to the rules using cheap oil or poor.quality gasoline, the proportions are not observed, or the mixture cooked a month ago, then the engine can also stall when trying to add gas.

How the real reason is determined

In the case when the carburetor is responsible for stopping the engine, a sudden stop is accompanied by a nearby symptoms. Most often, this is the appearance of tangible vibrations in all operating modes. Carburetor adjustment is carried out using two screws. idle control and fuel supply. In which direction to rotate them should be written in the operating instructions. If independent adjustment has not helped, contact the service center or buy a new carburetor.

If you have a lawn mower of a professional or semi-professional class, for example, the same echo or al-ko. then the carburetor resource is approximately equal to the durability of the motor and there is no need to buy a new one. It is enough to seek help in adjustment to a knowledgeable specialist. Motokos type Champion has a slightly lower carburetor resource, it may happen that adjustments will not help. Carburetors of two.stroke engines in the repair are complex, so it is better to order a new.

After making sure that the carburetor works fine, but the lawn mower still stalls, try to loosen the gas tank cover. If the engine operating mode has changed, it means that the lid valve is clogged or clogged. Practice shows that it is useless to clean it. It is better to buy a new cover, it costs a little, and it will last at least 2. 3 seasons.

Along the way, check the tightness of the gas pipeline connection from the carburetor and tank. Sometimes hoses stretch, and air is sucked around around the fittings. With a sharp press on the gas key, the mixture becomes depleted (gasoline is less than a stichiometric indicator) and the motor stalls. This also happens when the gasket between the carburetor and the cylinder is pierced or the bolts of the carburetor attachment are loosened from vibration. Just in case, check them, but do not forget that two.stroke engines are made of rather fragile alloys. If you overdo it with the moment of puffing, the thread in the cylinder can be disrupted.

It is also recommended to check the fence mesh on the hose in the tank, the cork through which the hoses are inserted into the tank and blow the fuel lines. Perhaps they are clogged and a little gasoline enters the carburetor. Especially with sharp pressure on gas.

Having checked and cleaning all the systems of the trimmer for the grass, season the tank prepared by all the rules by the mixture and start from the cold state. Let me work out for several minutes at idle and try to mow fishing at medium speeds. After 10. 12 minutes of work, add speed sharply. a trimmer for grass should not stall. If this happens, change the spark plug and perform the same actions.

If during operation a trimmer for the grass, before stall, spontaneously periodically reduces or increases the revolutions, “failures” appear in power, then it is necessary to check the ignition coil and contacts of all wires. Start with contacts, they are quite fragile and can break off or oxidize.

Why the chainsaw stalls when heated

The situation in which the chainsaws are started, and in the process of heating can stall, is familiar to many who are dealing with them. The main reasons for this behavior of the saw are the following.

Триммер Echo 330. Стоит ли он своих денег?

You can check the ignition coil using a multimeter or replacing it with a deliberately serviceable. Checking the primary and secondary winding multimeter is carried out in the mode of resistance measurement mode. The indicator of the resistance of the primary winding, the working coil, is 1 kOhm. secondary 4 rooms.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

clogging or clutching a valve located on the gas tank lid;
The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
problems with the circulation of the fuel mixture;
atmospheric air
The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

What is the resource of Chinese motorcycles?

Chinese or lawn mower is able to work about 500 mothers. But this is with the correct mixture, good oil, a good factory assembly. If a person fills gasoline with one good refueling, accurately measures the same oil along the Menzurka, the carburetor regulates the same mixture, the fuel burns correctly, then the coveted half a hundred hours of motor resources is a very affordable bar.

But here you can’t also forget about Chinese marriage. They even balance the shafts on their knee, put the cheapest bearings, carburetors stamp with clogged channels. If a person understands the principle of operation of a two.stroke engine and carburetor, understands how to sort it out, then he can eventually collect an almost perfect trimmer for grass.

In general, if we consider the Chinese motorcycle foam as a space for creativity, then even its breakdown is an occasion to study something new, this is a designer for a man.

If you need a tool, then it is worth finding a Japanese analogue, or switch to an electrical model.

Methods of elimination

Repair of a lawn mower is best started with a phased check of the main components. The first thing to check is fuel in the tank, as well as the presence of lubricants on the main nodes of the tool

It is also important to know what quality and what is the proportion of the fuel and oil used. If something is wrong, then the piston system may fail, and its replacement is expensive

Next, it is worth evaluating the serviceability and performance of the spark plugs. The result is evaluated by the presence of a spark when there is contact with the tool body. If the malfunction in the candle, then you need to remove the voltage wire from it.

In case of contamination, it is recommended to replace with a new one and drying the candle canal. This is also done if there are cracks or chips on the candle housing. The gap between the electrodes is set 0.6 millimeters. Squeezing a new candle is also produced by a special key. At the end, the voltage wire must be connected to it.

The inspection of filters, both fuel and air. If the blockages are strong, then the best solution will be their replacement. You can try the air filter with water with the addition of a detergent, and then dry. It is also sometimes soaked in gasoline

After drying and installation, it is important to moisten the filter with oil, which is used in the mixture with fuel

It is very easy to eliminate the problem in the form of a stalling lawn mowed immediately after starting. it is enough to adjust the carburetor according to the scheme given in the documentation. Sometimes you have to send the valves of the carburetor to facilitate the supply of the mixture in it.

Sometimes the lawn mower stalls due to the receipt of a large amount of air. In this case, it is necessary to increase engine speed to release it. It is also necessary to check the fuel hose for possible damage. If necessary, it is changed to a new.

It is important to maintain a gearbox clean, and its gears should always be treated with a special lubricant. It is worth noting that it is not always possible to repair a gearbox and starter on your own, therefore it is more advisable when breaking down these nodes to replace them with new

When reducing the engine power, it is worth paying attention to the exhaust muffler, or rather, to the net in it. She can clog because of soot from burned oil

This malfunction is solved cleaning the grid. You can do this using a small brush with wire or nylon bristles, as well as compressed air.

ECHO SRM 22GES Мотокоса. Триммер / Обзор и Отзыв Реального Владельца!

Clutch in benzocoses can break due to wear of the pads or a bursting spring. In both cases, the failed spare parts are replaced. Sometimes the clutch coupl is unusable, it can also be replaced with a new. over, on sale there are both couplings in full assembly and individual elements to them (washer, drum, etc. D.).

The lawn mower stall when you press the gas, how to eliminate the breakdown

The reasons why the lawn mower stalls is a huge number, we offer the most common of them, and we hope that you will find your own, and, of course, eliminate it. So, one of the situations is to clog the air damper, then the hole behind which the fuel is sprayed. If something got into it, then it can most often be quickly and easy to remove. This is the simplest reason, like a clogged filter. It needs to be washed in the solvent, and then get it well with compressed air. If it is not subject to repair, then order a new one in spare parts from the Kosikos store.

Similarly, when you press the gas, the tool stalls because the drive has clogged. The following option is possible: the fuel does not come in full, so you need to check or replace the fuel filter. To other possible reasons, the stalled motorcycles, when you give gas, should be attributed:

To all these reasons for which the mechanism stalls when adding gas, we will add several useful recommendations for the treatment of a motorcycle. First of all, before starting working with any equipment, you need to read the instructions. In this case, an important role is played by the consistency of gasoline and oil, correctly prepared by you, and also not to overheat the unit, and not leave gasoline for the winter when you simply will not use the machine.

In the full work of any tool, an important role is played by the coordinated work of all its components. And if in one it is a fishing line for a trimmer for motorcycles, then in the other a piston or carburetor. Motokos owners who want to use their tools at full power, you need to understand that the load on which the capacity of the machine is not designed may simply break the entire mechanism or its individual parts. Therefore, only competent and moderate operation involves the long.term effective work of any benchmate tool.

The trimmer stalls for grass at idle. the causes and their solutions

To common situations why a trimmer for grass or a lawn mower stalls, it should be attributed to its work at idle. Let’s immediately move on to the reasons:

heating the gearbox and sleeping on the drum as a result of the fact that the gasoline solution is not prepared correctly. The required proportion is 1: 4;
carburetor pollution;
The throttle flashed;
When opening the damper (if the experiment was carried out), the air flow makes a mixture of the “poor”;
Ringing the carburetor;
clogging of the air filter;

The insufficient amount of fuel that you need to work as a gas tool will entail a situation when at high speeds, with an increase. a trimmer for grass works and stalls in idle. In a situation with a carburetor. the device will stall for a cold launch and “on hot”. For any user, Motokosa. Professional and Amator, it is important to understand that any tool problem can depend on the petty flying of the part, the release of fastening or clogging, as well as on the global breakdown of the important part of the mechanism.

Despite all kinds of problems, your device, nevertheless, needs such an obligatory component as knives for motorcycle, without which the exploitation of braids for grass is simply impossible!

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence of fuel hose cracks or problems with the oil seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.

Why stalls a gasoline trimmer for grass

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns. The most common problems contain instructions for operating. Know the reasons why the trimmer stalls for the grass, it follows to independently effectively perform the repair of the device.

The unit can stall immediately after the launch, if the carburetor is sipped or incorrectly configured. this causes an uneven supply of fuel. The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when the valve supplies fuel clogs. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
mechanical damage to wires, tubes, hoses;
The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Immediately after you started

The unit may stall immediately after starting, if the carburetor is shifted or incorrectly adjusted. This causes an uneven supply of fuel. As a result, the device vibrates clearly. To eliminate defects, the carburetor is reconfigured, following the annotations to the mechanism.

Apart from that, the engine stops when clogging the fuel supply valve. In such cases, it is quite easy to clean it. If the bureau at first earned, but later stalled immediately, then maybe the fuel with some difficulty falls into the carburetor knot. Weakening of the valve helps to solve the issue, which ensures free circulation of the consistency in the system.

The stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks), taking fuel. In this case, increase the speed of the drive in order to resign more air from the system from the system.

Where to look for a reason or where to start checking

All chainsaws have the same design, and work according to one principle. The device of the chainsaw can be found in this material. It does not play much meaning which brand of the tool. Stihl, Husqvarna, Echo, Champion, Partner, Sturm and others. A malfunction manifested in the form when a chainsaw is stalling when pressed on gas can arise the same both on expensive and high.quality tools and on budget Chinese devices. If the problem has arisen, then it needs to be solved.

A chainsaw is a system of mechanisms consisting of details. Any detail in the mechanism can fail, which will lead to a partial or complete failure of the tool. If the tool engine starts, then this does not mean that the chainsaw is completely serviceable. Когда при повышении оборотов происходит прекращение работы двигателя, значит на то имеются соответствующие причины. With this malfunction, you need to pay attention initially to a number of the following tool mechanisms:

Gas tank. make sure of the presence of fuel. If fuel is in sufficient quantity, you should also check the serviceability of the fuel filter, the presence of a connection of the supply hose with the carburetor, and also make sure that the operability

These are the main details and mechanisms that should be checked first if there is a malfunction when the chainsaw stalls when the accelerator is pressed. There are other reasons why the chainsaw engine stall when the gas trigger presses. What else can contribute to this malfunction, as well as features of elimination of breakdowns, we will find out later.

Sources:

https://labequip.ru/trimmer-benzinovyj-rezko-zagloh-i-ne-zavoditsa/
https://hitech-online.ru/tehnika-dlya-sada/trimmer/glohnet.html
https://www.avtoprin.ru/deprivation/pochemu-benzokosa-Echo-tupo-nabiraet-oboroty-pochemu-glohnet/
https://www.albytools.ru/articles/pochemu-glokhnet-dvigatel-trimmera-pri-nabore-oborotov/
https://ktexnika.ru/drugoe/pochemu-glohnet-trimmer.html
https://xnb1ac1aqnee.xnp1ai/elektroinstrumenty/ploho-zavoditsya-trimmer-na-holodnuyu.html
https://slavasozidatelyam.ru/strojka-i-remont/benzokosa-ne-zavoditsya-na-goryachuyu-prichiny/
https://jusof.com/trimmer-Echo-ne-nabiraet-oboroty-prichina/
https://xnb1ac1aqnee.xnp1ai/elektroinstrumenty/pochemu-trimmer-glohnet-pri-nazhatii-na-gaz.html