How to remove a hander hgt trimmer for grass.

How to remove a coil from a trimmer for Huter grass

No wonder they say: “”Forewarned is forearmed“”. Knowing the possible problems and causes of occurrence, one can prevent them in a timely manner. We recommend remembering or leaving a memo.

For a better understanding of the mechanism of the process of replacing fishing line in a spool with video assistance prepared by Fubag specialists:

Types of coils by the method of fishing line

Most amateur and household motorcycles stand out by a simple device. They consist of an engine, a bar in which a flexible or hard drive shaft, a handle and a cutting organ is located, the role of which often plays the head of a trimmer for grass. On the principle of feeding fishing line, the heads are divided into the following types:

• manual-a headset of this type got its name due to the fact that the cutting cord in it is served manually. Each time, if necessary, lengthen the fishing line for the trimmer, the operator must stop working with the trimmer and pull it out mechanically. This brings its inconvenience, but it is this type of device that is considered the most popular among gardeners. Hand coils differ from analogues of durability and low prices;
• semi.automatic. when working with heads of this type, you can lengthen the cord by pressing the headset to the ground. During this, pressing the button that drives the anchor mechanism occurs. He creates a centrifugal force that pushes the cord outward. The semi.automatic head for a trimmer for grass has one important advantage. when operating it, it is not required to stop working with a motorcycle, since you can lengthen a fishing line for a trimmer with a running engine. The only drawback is that the semi.automatic cutting headset costs a little more than hand coils;

automatic. regular devices of this type are convenient in operation. To lengthen the cord to the operator, it is enough to slow down the engine speed motorcycles. Automatic factory coil for a trimmer for grass differs from analogues with ease of operation. However, the for a headset of this type are the highest in the market.

Each of the listed types of cutting devices is suitable for operation in certain conditions. Hand heads are best used in areas with solid obstacles. The low cost of a headset of this type will make it possible to buy several manual heads at once, and alternately change them as it fails. Automatic models, on the contrary, are quite expensive, so it is best to use them to care for clean areas.

Download instructions from the ILT trimmer lawmaker for Hander HGT-1000-2 grass

For many products, for working with Hander HGT-1000-2, various additional files may be needed: drivers, patches, updates, installation programs. You can download these files online for a specific Hander HGT-1000-2 model or add your own for free downloading other visitors.

If you have not found files and documents for this model, then you can see incections for similar goods and models, as they often differ in small changes and are complementary.

Reviews about Hander HGT-1000-2

Be sure to write a few words about the product you have received so that everyone can get acquainted with your review or question. Show activity that as possible more people as possible were able to find out the opinion of real people who were already used by Hander HGT-1000-2.

A fairly reliable average power tool. Quite suitable for a summer cottage 5-6 acres

Acquired HGT-1000-2 twelve years ago. He worked properly until he stumbled upon a piece of iron in the ground. The coil broke.

Reviews about Hander HGT-500-1

Be sure to write a few words about the product you have received so that everyone can get acquainted with your review or question. Show activity that as possible more people as possible were able to find out the opinion of real people who were already used by Hander HGT-500-1.

The main and most important characteristics of the model are collected from reliable sources and in terms of characteristics you can find similar models.

Basic breakdowns

Here is a list of the most common and common breakdowns and malfunctions of lawn mowers and trimmers. If you have such a breakdown, then you are lucky, this is a typical malfunction for Hander HGT-500-1 and you can ask a question about how to eliminate it and will be quickly answered or read in the questions and answers below.

Basic breakdowns

Here is a list of the most common and common breakdowns and malfunctions of lawn mowers and trimmers. If you have such a breakdown, you are lucky, this is a typical malfunction for the Hander HGT-600 and you can ask a question about how to eliminate it and will be quickly answered or read in the questions and answers below.

Winding fishing line on a trimmer for grass

Measured and accurate dismantling of a spray from the coil of braids for grass makes it possible to go directly to the winding of the fishing line. Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation. Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off the excess.

Trimmer head for grass with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode. It is almost impossible to incorporate a fishing line for a trimmer to a trimmer for grass with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic head of the trimmer for grass include the simplicity of the line for refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

How typical mechanical defects and ways to eliminate them with your own hands are manifested

The following damage to the kinematic scheme most often occurs on the electrimmer:

• the bearings of the electric motor are cleaned or spoiled;
• The fishing line for the trimmer is tangled or broken due to incorrect winding to the coil;
• The torque from the engine to the mowing head is not transmitted;
• The plastic case and individual parts melts when overheating due to increased loads;
• enhanced vibration of a rotating head is created, which makes the kosbu.

How easy to check the work of bearings

It is enough to update the external clip regarding the shaft and immediately with tactile sensations of the fingers to evaluate the smoothness of their work, the state of backlash. Broken and worn bearings must be replaced. Do not forget to update the grease if necessary: ​​remove the stream and apply a new.

Trimmer heads are created by three types of structures, implying the issuance of fishing line in one of the ways:

The overwhelming number of products uses semi.automatic fishing line. It also allows a manual regime for adjusting the length of the cutting area. A large number of breakdowns are associated with a violation of the operating rules recommended by the manufacturer, when a trimmer for grass begins to work outside of its capabilities. These include:

• a significant excess of the diameter of the cutting fishing line leading to an increased load on the engine, intermediate shafts, gearbox and mechanical parts of the head;
• installation of homemade knives or chains instead of standard structures;
• Incorrect winding of the fishing line.

Such are the homemade like “eternal fishing line for a trimmer for grass” not only damage the kinematics of the lawn mower, but also injure people, causing harm to their health. I do not advise doing this to do. There is no economy here.

How easy it is to wind a fishing line for a trimmer on a spool

Usually this issue is difficult for beginners. Especially for this case, I made a narrative on my channel Yandex Zen. I invite you to familiarize yourself: information is presented by pictures with an explanatory text.

The engine works, but the spitter head does not rotate: what’s the reason

The breakdown is associated with the cessation of the transmission of the torque of the engine to the working body. A defect can occur anywhere in the gear. Most often, in models with the gearbox, the reason lies in the wear of the working faces of the gear. over, if the teeth on one are worn out, then both must be changed at once, because the second also suffered

Hysteria gear malfunctions most often arise after the loss of grease in them, which, by the way, each manufacturer is noteworthy. The fact is that the design of the trimmer gearbox body is not completely tight

Otherwise, its cost will increase strongly. Gears should always work in lubrication, and it is consumed. If it is not replenished, then the breakdowns are inevitable, which happens quite often. In cheaper structures without a gearbox, a coil of the coil is fixed through a plastic sleeve to the shaft. During constant loads, plastic heats, and the sleeve wears out during operation, the head begins to hang out. When the critical value of the backlash is reached, the sleeve must be replaced.

Why can the lower part of the composite rod

The reason for increasing temperature in this place can only be strong friction of rotating parts about fixed parts. In other words. the spring shaft is tightly pressed against the walls of the plastic insert. (See above the photo of the details of the composite bar). This leads to melting the plastic up to damage to the sleeve and the formation of a continuous lump from it, penetrating the boots of the shaft. When cooling in the air, a monolithic structure is created, which can block rotation and even jam the engine. The rotating spring shaft of the bar should always work in the environment. It must be regularly lubricated. Timely perform preventive examinations and work.

Why is there increased vibration and how to get rid of it

We understand that any well.balanced part regarding the axis of rotation does not create vibration. Beats arise where the factory balance is broken or there is a marriage. The mowing head has a fairly large mass. Therefore, it is often the cause of increased vibrations, but in each case it is necessary to study this issue on a specific design. The owner of a short Masterlom video, Masterlom, shares his experience in eliminating such a defect on the Tekhmann DCE-2014B electrician. His achievements and ideas can be useful to you in eliminating vibrations. I recommend to see.

Forest winding algorithm

The type, thickness and length of the mowing fishing line are selected depending on the model of the trimmer for the grass. The diameter of the cord can be from 1.2 to 4 mm. It is easy to guess that the thicker you are refueling the cord, the tougher and thicker it can be cut.

There are 3 ways to find out what kind of fishing diameter you can use on your mower.

• Contact the instructions of the device for information about the thickness of the cord.
• Look at the coil itself. It can be marked with information about the possible diameters of the mowing fishing line.
• Insert a trimmer fishing line into a socket. If it passes into it easily, you can use a cord of this diameter.

The fishing line for a trimmer is wound on a coil located in a mowing head. Therefore, it first needs to be opened (this was discussed above). There are two ways to wind the cord.

Manual bobbins

A manual mowing head is a coil in which the cutting cord during wear is stretched by the owner of a trimmer for the grass on its own. To do this, turn off the tool, remove the head and with the help of hands stretch the fishing line for a trimmer to the required length. However, despite some inconvenience, this type of head is considered the most reliable.

Most amateur and household motorcycles stand out by a simple device. They consist of an engine, a bar in which a flexible or hard drive shaft, a handle and a cutting organ is located, the role of which often plays the head of a trimmer for grass. On the principle of feeding fishing line, the heads are divided into the following types:

Each of the listed types of cutting devices is suitable for operation in certain conditions. Hand heads are best used in areas with solid obstacles. The low cost of a headset of this type will make it possible to buy several manual heads at once, and alternately change them as it fails. Automatic models, on the contrary, are quite expensive, so it is best to use them to care for clean areas.

Review: trimmer head Huter. One of the serious ambush of trimmers Huter.

A semi-automatic head with a fishing line for trimmers Huter Eth-1200 is supplied with a 2mm thick with a thick-colored fishing line of 5m.Height of the head 320g.The head has a bobbin with a fishing line and two metal holes through which the ends of this fishing line are removed that carry out the mowing of the grass during the rapid rotation of the head of the trimmer for the grass.Designed for electric trimmers Huter Get-1200SL.

When the grass is spent, the ends of the fishing line wear out and their length decreases.Therefore, the radius of the capture of the mowing becomes less.You can restore the length of the ends of the fishing line with a slight blow to the ground of the button located in the center of the head, when the head of the trimmer for grass is gaining momentum.

After that, the two ends of the fishing line will supply, the excess of which will be cut off when the trimmer for the grass rotates for the grass.

Sooner or later, one of the cutting ends under the root breaks out at the fishing line and it is necessary to re.dispatch it, or the fishing line for the trimmer ends and it is necessary to wind up a new one.

In short, it becomes necessary to remove the head cover and pull out the bobbin bobbin from the housing.The most interesting begins here.A similar situation is described in the fable of Ivan Andreevich Krylov “Monkey and glasses” 🙂

The fact is that the trimmer head Huter has a unique design.I have never met any company.Open it for reloading fishing line is not for the faint of heart.

Description of how to do this is missing.The inscription on the back of the head of the head in English “click to open” did not help.Pressed, tried to turn the body in both directions.Nothing helped.

Finally realizing that my brains were not enough for the first non.destructive discovery, he reconciled with this and began to look for knowledgeable people.The cheerful and friendly saleswoman in my village store for the sale of power tools and devices for them helped. Antonina, showing how this is done. Thanks to her for that!

Over time, I, of course, forgot this unique experience.To bow again to Antonin was already inconvenient.I had to turn on the brain, and it is objectively and in detail to deal with the problem.The Internet was prompted by the method of uprooting the head of the head head of the head.Which did not suit at all.

From the video found, the head device understood.It turned out that the lid is held on four holders attached in the nests of the body and is fixed with a latch.Having squeezed which the corresponding screwdriver with a flat blade and turning the body clockwise, you can easily remove the lid and pull out the bobbin with the remains of the fishing line.

Fishing line refueling is standard and described in detail in the description of a trimmer for grass.Also not simple, but you can figure it out.

When using the head for a sufficiently long time, a little earth, the remains of grass and all dirt are packed into it.For the benefit of the case, I cleaned the dirt from the body and the outer parts of the head.

The head is not difficult to assemble.Necessary:- Title the ends of the fishing line into the corresponding holes of the case:

In the photo, among other things, on the bobbin you can see slits for fastening fishing line sizes from 1.6 to 2.6mm. For electric trimmers, Huter Get-1200S is recommended a fishing line for a trimmer with a diameter of 2mm, which is reliably fixed in the slots for fishing line 2.4mm.

Next:- Combine holders with the corresponding slots in the hull cover. with a simple press on the back of the case with an inserted bobbin with a fishing line. click the latch. turn the body counterclockwise.

I received great satisfaction after it was finally able to remove the lid of the head :)) The feeling of victory over the rebellious and hostile to you nature 🙂 as a taming of Claudt’s horses on the Anichka bridge of St. Petersburg.

Buy or not such a head for trimmers?Only if there is a desire to fight her when replacing a fishing line.In addition, the weight of this head is 15g above the weight of a similar head from Patriot trimmers.How important is it. I don’t know.

The plastic is ordinary, I haven’t scattered yet.But, people complain of its fragility. With careless attacks on the ground, it can be crumbled.

In fact, the thread in the head is standard left m10x1.25 LH.Accordingly, the head for fishing line with a diameter of 2mm can be used standard with the same thread, for example, from a trimmer for Patriot grass.

Offers at different of different manufacturers in the market enough.From the most democratic to completely prohibitive for automatic heads.You can choose the most suitable for you.

Repair of the head of a trimmer for grass Huter Get-600. Modernization of the Huter Get-600.

There is nothing to write about the car. Rides. Pleasing. I’m not going to copy the corresponding forum. I decided to share personal experience in another.

I have in the farm in addition to a classic braid for grass and a pair of gasoline electric trimmer for Huter Get-600 grass

Under certain circumstances, it turned out that the head in the kit is very tender, and with a slight effort about the bricks hidden in the grass broke. I did not dare to buy this head anywhere on the Internet, including on Alibab without trying on a mower. Local shops shook their hands

I had to select from the availability.To begin with disassembly. To remove the head, you need to either disassemble the entire trimer, and holding an anchor in a vice to twist it, or follow my inhumane approach and carefully cut the body with a hacksaw on metal and sleep the shaft, creating a groove for a screwdriver for a screwdriver. Further, everything is simple. Thread m8 ordinary right. The head of the head is still thrown out. Island, wound around solves the problem of 10 minutes. Then it unwinds it and ripens about the same ill.fated brick.

Then a trip to Magaz behind a new head. Many heads have been tried, I stopped at one. The price of the question yourself in the photo see.

The revision is as follows: 1. Sprinkle the long protruding hub up to 5-7 mm.

By that time, the file had broken down, the wheels for the corner grinder ended, so I hid on the sandpaper. You need to cut off so that the impeller does not hurt the mowing housing, and there was no very large gap, otherwise the juice of grass and pieces of snails will be anchored inside.2. Drill a hole with a drill 8 mm upper part. The fact is that entering the hole is 8 mm, and for thread on this head is left under M6. The shaft of our trimmer for grass 8 mm. If you drill more than 8 drill, it will be freely scroll.3. Nothing that the m8 nut does not climb inside. Put the puck of an ordinary flat 8 mm flat with an outer diameter of 14 mm and tighten the nut.

The nut works for the anti.income, so it should be delayed when rotating the head. With a great desire, you can grind a threaded sleeve with an external diameter of 13 mm with a thread M8 and stick on an epoxy inside. Then the head needs to be drilled by 8.2 mm and just go to the shaft. This is the next stage when.All. Tests have shown that now I have an automatic head, working standardly from a blow to the ground, in contrast to the original, which you need to do it manually. Does not scroll at the shaft. All temporary. constantly.

Комментарии и мнения владельцев 33

Log in or register to write Комментарии и мнения владельцев, ask questions and participate in the discussion.

Without refinements, I picked up such a coil, all one to one, I threw the nut from the old coil, the price tag does not please, I cost 720r.A coil for a trimmer for grass, automatic, nut M8 x 1.25 right, fishing line for trimmer 1.6 mm Denzelarticule: 96308

I bought such a head and drilled a hole of the desired diameter in it. But in the process of drilling, the drill took a little to the side. Now alignment is violated and vibration is felt during operation. So I think to buy one more. Maybe there is a cunning/secret, how to drill evenly?

PATIRON DL-1223-a complete analogue of the coil in the article for 250 r. In the most common online tool store. You don’t even need to undermine and drill anything, only the washer will be needed.

You put the Patiron DL-1223 on the Huter Get-600? Everything came without improvements?

Hello! I did everything exactly like in this post! Parents are satisfied!

If there are 3D printers, then it is not a problem to make, but 500 are curled up, it’s easier to buy a new one. If you need a 3D model of the cover by which they cast, then this is. write.

I really want the cap model, please throw off!

If there are 3D printers, then it is not a problem to make, but 500 are curled up, it’s easier to buy a new one. If you need a 3D model of the cover by which they cast, then this is. write.

Hello! Please share the cover of the cover!

Repair of the head of the head of a trimmer head for Huter Get 600 grass also needed after meeting with a pebble But why cut the head with a hacksaw. because it is easily removed from the anchor shaft: for this we unscrew the side screws above the electric motor and insert a wide screwdriver into the collapse of the case and turn it to remove it to remove it to remove it upper yellow hatchet. Under it we will see the rotor shaft with the “bald ones” for which you need to hold with a key or pliers and unscrew the head behind the trimmer head body. There is a m8 nut with ordinary right thread. For one you can get the collector brushes and see the collector node of the motor. if something is cleaned with zero with sandpaper and generally clean the body of the motor from dust. As for the broken latch on the lid, then it all depends on the degree of breakdown: if the tip of the latch fell off, then we do not break off the opposite latch, and if the latch broke off to the lid, then we break off (bite off) opposite the other latch to the lid. This is necessary for balancing- so that the renovated head does not vibrate. Next, we act as follows: from the end of the rotor (after removing the head and removal of the rubber plug above the nut) there is an already seconded recess. we drill 3 drill.5 mm to a depth of 10 mm hole and then cut the thread m 4. Now we are drilling in the head of the head of the trimmer for grass (without latches) in the center of the hole of the diamond of 4 mm. All: now we collect everything back, and fasten the lid of the head with a screw under the screwdriver with the corresponding puck. The thread is put on the screw, and the trimmer for the grass turns to the left. the lid will never unscrew. I have experienced and the second season the head on the trimmer is working. If you do not want to drill the rotor shaft, you can make a transition sleeve with a diameter of 14mm-inside on the one hand, the M8 thread (preferably 1st size in the sizes in the sized) and on the other side of the sleeve M5 or M4 carvings-where you will fasten the cover again with the help of the screw. Trimer head is considered a diameter of 75 mm, but in reality, if it is cleaned with sandpaper outside, then it will be 74mm, so support a tin can from condensed milk. cut with ordinary scissors the desired size of the window for a trimmer fishing line and put this “case” on the head and in the head screw the end with a screw through the lid to the anchor and you will be a durable head. As for the replacement with another head, then it must be borne in mind that the head with “ribs” is needed to cool the electric motor and anyone will not work. Now they began to produce on the Get600 heads with curved cooling ribs, then it should be taken into account that they should suck the air inside the engine when it rotates.

Such a muck instead of thread was in my case A diameter is 8mm, I think to cut and order an adapter from the turner for a universal head And so the trimmer for the grass is good, powerful and not expensive, unfortunately the spool sucks.

TRAMMER Repair for Huter grass with your own hands

Details: Repair of a trimmer for Huter grass with your own hands from a real master for Olenord.com.

An indispensable tool for a modern summer resident or the owner of a private house is a lawn mower, which allows you to effectively and efficiently bring the adjacent territory in order. The period of active use of motorcycle is in late spring until October of the month. Modern units are equipped with powerful and hardy ICEs, enhanced transmission and main nodes. Despite this, physical wear, production marriage or improper exploitation leads to the failure of a trimmer for grass. In order to repair a trimmer for grass with your own hands, you must have at least basic knowledge in the field of technology and a little experience in its repair.

The main node of any gasoline tool is the internal combustion engine (ICE), which through various methods transmits a rotational moment to the executive body. In a modern benzocosa, a duralumin rod (pipe) is used as an element of the transmission between the motor and the trimmer head, inside of which the drive shaft is located.

Thanks to a highly reserved engine, the frequency of fishing line can reach 13 thousand revolutions per minute depending on the producer of the braid for grass. In order to exclude mechanical and temperature damage to the gearbox, a special opening is provided for the introduction of ointments in its body. As a facilitating headset for the owner, during prolonged work, all modos models are equipped with a strong belt over the shoulder.

Regardless of the manufacturer, almost every model comes with fishing line and steel knives.

The transverse section of PVC Lines for a trimmer for grass can vary from 1.5 to 3.0 mm.

Made from a durable polymer, during kosba it is subjected to intensive wear and, as a result, a break. Therefore, from time to time it is necessary to check the presence of a fishing line in the head and, if necessary, replace it. It is recommended to purchase an additional bobbin for quick replacement with a reel with a fishing line ending.

The trimmers presented today on the market for ICE grass are equipped with a D-shaped, U-shaped or T-shaped handle, where the main controls of the unit are located. For example, in a spit with a U-shaped handle key and a “stop/start” toggle switch are located on the right handle. In the D-shaped version of the gas control key, the gas adjustment key is located directly on the bar.

In view of the presence of many nodes and details, the repair of a trimmer for the grass with your own hands involves the elimination of breakdowns that prevent its normal operation. It should be noted the most basic malfunctions of gasoline cos:

• The engine of the trimmer for the grass does not gain momentum;
• Breakdown of the cylinder-piston group (CPG);
• Ignition malfunctions;
• There is no connection between the internal combustion engine and the trimmer head;
• Mechanical knocks when operating the unit.
• Repair of the CPG lawn mower

The main node of any internal combustion engine is the cylinder-piston group (CPG), which can fail due to wear of parts of parts or low quality of the fuel mixture.

Lubrication of the rubbing nodes in a benzos is carried out by adding a certain proportion of oil to gasoline. This process can be disturbed due to the old oil dropping in the form of sediment. In this situation, when the trimmer for the grass is launched, the motor overheats greatly and in a matter of minutes the most expensive breakdown occurs. To eliminate the malfunction, a complete replacement of the CPG, namely: piston, seals, cylinder and piston rings will be required. If you are not a technical engineering master and do not have experience with technicians, then the engine is unlikely to be corrected without the help of a specialist. In detail with the stages of repairing a piston trimmer for grass, you can find here.

When you fail to ignition of the lawn mower, a spark on a candle disappears and, as a result, there is no ignition of the fuel mixture.

It is important enough in the current situation not to rush with the replacement of the coil, since the cause of the breakdown may be in the absence of contact in the switch on the control handle.

An important point in the search for the ignition of a trimmer for the grass will be diagnosed with Sich, where the distance between the lateral and central electrode should be 0.5-0.7 mm. In addition, it is necessary to pay attention to the sealing ring of steel on a candle, the loss of integrity or the deformation of which can lead to etching of the combustion chamber and, as a result, reducing the power of a braid for grass.

If the replacement of the check of the electric circuit, candles and its contacts did not give positive results, then you should pay attention to the ignition module of the trimmer for the grass, namely to the gap with the flywheel. Regardless of the design features and the manufacturer of the lawn mower, the distance between the ignition coil and the flywheel should be no more than 0.2 mm. To restore the optimal value of the clearance, it will be necessary to relax the bolts of fastening the coil and a special measuring probe set the ignition of a trimmer for the grass.

A clear sign of malfunction of the engine power system is the absence of traces of the fuel mixture on the electrodes of the candle, which may be associated with the following defects:

The fuel system of the trimmer for grass

• In connection with a clogged hole in the gas tank, a vacuum is created, which prevents the normal flow of gasoline into a carburetor;
• In view of the low quality of fuel and the hit of foreign particles, the fuel filter installed in the tank clogged;
• not the intake of the mixture in the combustion chamber as a result of the carburetor.

It is possible to quickly determine the cause of the malfunction by dismantling the fuel hose leading to the carburetor. If the fuel mixture flows in a thin stream, then you should pay attention to the carburetor. In the absence of a jet, it is necessary to clean the thin needle of the cabin (a small hole in the gas tank cover) or replace the fuel filter.

If the fuel enters the carburetor, then it is necessary to clean it or adjust. Adjusting the carburetor of a trimmer for grass implies the restoration of optimal mixture mixing.

Carburetor trimmer for grass with tuning screws

To do this, pay attention to three adjusting screws: maximum revolutions (h), minimum (l) and idle (LA). First you need to configure the screws h and l, and let it go for 1 turnover each. After starting the braid and let it warm up for 10 minutes to adjust the power system in working mode. After warming the ICE, click on the gas supply key to the stop (12,000 rpm). Restore the idle mode by turning the screw La. As soon as the head of the trimmer for the grass of the start of rotation, it is necessary to wrap the screw until it stops.