Electrics how to wind a fishing line for a trimmer for a trimmer for grass.

How to wind a fishing line for a trimmer for a trimmer for grass: step.by.step guides and video instructions

A beautiful lawn will look truly well-groomed only if you regularly give up grass. For processing complex areas, a trimmer for grass is best suited. Any owner of the unit will sooner or later collide with the solution to the problem, how to wrap a fishing line for a trimmer to a coil, because from incorrect actions you can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review, we will talk about all the ways and nuances of the replacement of fishing line and the features of the selection of consumables.

It is convenient to use a trimmer for grass for pumping small or complex areas, for example, near the hedge, between the beds and along the paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any requests of the owners.

As a cutting element of a trimmer for grass, a fishing line for a trimmer is used. In the process of work sooner or later, its length will end, and then the owner will arise the question of how to properly replace and fix the thread tucked in the removable coil.

What to consider when choosing a fishing line

Before inserting and fixing the fishing line for a trimmer in a removable coil of a trimmer for grass, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Review of manufacturers and models, as well as useful tips from experts considered in this review, will help in a difficult choice among many models of devices.

By quality

Before you put a fishing line for a trimmer on a trimmer for grass, you need to pay attention to the cross section of the cord:

• Round cross.sections are the most common option. They perfectly give way to grass even in complex areas;
• A line for a trimmer with a spiral section is suitable for thin grass. It is not very durable and is not suitable for old thickets;
• The cord with zabrinki and sharp faces is chosen for mating by weeds;
• A fishing line for a trimmer with a variety of geometric sections will help to mow the lawn more evenly, but the strength of the consumable material is low.

Important! The most wear.resistant consumables are a two.component fishing line for a trimmer with a round section, enhanced from the inside.

The owner of Motokosi should know that it is categorically impossible to use metal wire, fishing thread and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electrochemmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

In size

Before winding the thread, you should pay attention to its size to the coil of the trimmer for the grass. Most often use a fishing line for a trim with a cross section of 2 mm.

You can choose the right diameter in the following ways:

• View recommendations in the manufacturer’s instructions for trimmer.
• Often manufacturers apply information about the cross.section to the bobbin.
• The cross section of the cord should be suitable for the diameter of the coil opening.

Important! The thicker the thread will be seasoned, the more rigid grass it will be able to mow.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

• Exclude spontaneous start,
• Delete the battery (if used),
• Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Autocut braid head

The two.stringed model is designed for mowing and clearing the territory. Its four.stringed modification is suitable for trimming in obstacles (stairs, walls, thresholds, borders) and processing large areas. Differs from the previous design by automatic adjustment of the length of the cutting strings. right during operation. To supply the stock of fishing line, touch the lower edge of the mowing head to the surface of the earth. This will weaken the cord lock, and it will advance under the influence of centrifugal force.

Supercut braid head

This two.string design is also designed to mow and clearing space and is used in obstacles and processing large areas. For the cutting cord, an automatically supported optimal cut length is implemented here. It is used only with a universal or special protective shield for the mowing.

We will explain how to refuel a fishing line for a trimmer to a trimmer coil for the grass of these two modifications. First, prepare two strings of maximum length (7 m or 10 m), depending on its type. You can find out these data on the packaging sheet.

• Take the head in your hand so that its cover with a bulge in the center is from above. Thick two recesses located on the sides of the structure with the other hand. they are exactly opposite each other. Press your fingers in these recesses at the same time or in turn so that the constipation comes out of the hook, and then click the other. Turn the lid clockwise: now it can be removed and put aside.
• Take the coil itself. To do this, slightly cram it to free the plastic hook. With rotational movements, bring it out of the holding position and raise it up. A free drum with two compartments will be in your hands.
• Find the ear, which adjoins the dividing wall in the middle of the bobbin. Take a fishing line for a trimmer for a trimmer for grass and insert its end into this recess until it stops. Having bent the string, wrap it around the coil in the opposite direction so that the fixed piece of the trimmer cord does not fall out of the ear. With quick and confident movements, continue to wrap the line for the trimmer turning behind the turnover, trying to distribute the layers evenly and tightly. Когда отрезок закончится – другой конец струны зацепите за одну из двух насечек так, чтобы наружу выходил остаток примерно 10 сантиметров.
• Make the same actions with the second string. Wrap a fishing line for a trimmer in the second compartment on the same side. Fix the free end of the same length on a notch located on the opposite side. After that, the coil can be inserted back into the body.
• With rotation of the bobbin, compare the strings and sleeve inserted into the head so that they are next to each other. Take each of the forests, carefully unhook it from the notch and put it in a special groove for exit outside. Now the ends stick out of the channels of the rumps and the lid can be closed. Put it on in accordance with the position of the fixers and press it strongly to the click.
• Pull strongly by one string so that the reel body shifting a little up. You will hear another click, and part of the fishing line will come out a couple of centimeters.
• The next action can be cut out by the ends of each string by the secateur to the required equal length, if necessary. STIHL recommends that the trimmer fishing line protrude from the hole for about 10 cm.

Insert a new thread

Before updating the thread, be sure to turn off the engine and pull out the network plug! Press the lock (b/1) and turn the cover cover (b/2) to the stop (nose on the lid (b/3) should be in the middle of the lock) separate the lid (b/2) from the body (b/4) remove the coil (Iv/5) from the body and remove the remains of the old thread.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. in the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. from 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

• round. universal, most durable, for rough grass;
• curly. for soft plants;
• Twisted with notch. for thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

How to change a fishing line for a trimmer on a trimmer

The fishing line for a trimmer is wound on a coil (bobbin), which is located in the body of the head of the trimmer for the grass. First, unscrew the head from the bar with the motorcycle cord and open it the top cover, pressing on the side latches. In some models, the case simply spins.

We take out the coil, clean it from dirt, the remains of the old fishing line. Coils are one- and two-section.

Fishing line winding on a single.section coil

We take 2 m of fishing line, we spread it up to half through a special hole inside the coil. The ends of the fishing line of the same length stick out from both sides. We wrap them with both along the groove of the coil in the direction indicated by the arrow on the case (back to the rotation of the coil on the shaft of a trimmer for grass). We do not wound the fishing line for the trimmer to the end-pieces of 10-15 cm, which will be workers, fix in grooves on board the coil. Fixation is needed so that the fishing line for the trimmer is not unwound when installing it in the head of a trimmer for grass.

We insert the coil into the body of the head, while at the same time we spread the free ends of the fishing line into the holes of the body, set. We collect the head, put it on a trimmer for the grass. Everything, the change of fishing line in the trimmer was carried out.

How to wind a fishing line for a trimmer for a trimmer for grass with a two.section coil

If there are two sections in the coil, put the fishing line for the trimmer in half and insert the fold place into a special groove in the side between the sections. We begin to wind the ends each in its own groove. then everything, as in the case of a single.section coil.

How much fishing line is wrapped on a trimmer for grass? You can wind 2-4 m, depending on the product model. In each case, it is impossible to wind too tight, the thread should have a free move for stretching during operation.

How to change a fishing line for a trimmer on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a mower for grass, where a fishing line for a trimmer played the role of a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so that the idea itself was transformed into mowing around obstacles without damage to the very cutting apparatus of a mowing room. For a neat mowing around obstacles, you can have a head with a smaller fishing line, it is easy to change it when moving from mowing large areas to delicate blocking. However, periodically and the cutting tool itself requires replacement. We tell you how to disassemble the head of the lawn mower (trimmer for grass) and wind a new fishing line for a trimmer.

All about the replacement of fishing line with a trimmer head

There are many types of heads that are designed for different types of fishing line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this fishing line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a fishing line for a trimmer is less durable than round, on average it is consumed less. A square fishing line for a trimmer quite easily cuts the shoots of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good fishing line for a trimmer that remained for the winter, in the spring suddenly behaves completely differently. it breaks, stops doing normally from the reel. There is a recommendation to soak a fishing line for a trimmer in the water before work, but I do not see much sense in this, malein anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breakdown or constantly torn fishing line for a trimmer, which also does not want to leave the reel itself, can significantly complicate the work.

Winding fishing line on a trimmer for grass

Measured and accurate dismantling of a spray from the coil of braids for grass makes it possible to go directly to the winding of the fishing line. Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil for grass with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling fishing line can range from 2 to 5 meters. The end of the fishing line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side. On most coils on the outer side of the case there are marks in the form of arrows, which indicate the direction of the movement of the bobbin of the trimmer for the grass.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer fishing line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation. Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off the excess.

Trimmer head for grass with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode. It is almost impossible to incorporate a fishing line for a trimmer to a trimmer for grass with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic head of the trimmer for grass include the simplicity of the line for refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

How to insert a fishing line for a trimmer into a trimmer for grass?

Refueling a mowing coil of cutting thread for a trimmer for grass is not a complicated occupation, however, novice gardeners will have to practice a little to be able to quickly insert the cord into the existing household trimmer for the grass.

There are several ways to refuel a mowing head of a trimmer for grass. The first method is the simplest and is well suited for beginner gardeners.

In this case, the cord is inserted into the coil in the following sequence:

• First, you will need to reinforce from a common spray of about 6 m fishing line for a trimmer for grass, and then cut the resulting segment in half. As a result, 2 threads should be obtained, 3 m long;
• Then, at one of the ends of the first segment, you need to make a peculiar hook, and insert it into one of the through holes located in the upper part of the spool;
• Next, you need to start wrapping the fishing line on the spool in the direction indicated by the arrow. During winding, it is necessary to ensure that the fishing line for the trimmer evenly lays on the surface of the spool, and does not go beyond its upper section. It is not necessary to wind the segment until the end, about 15 cm of thread should remain in the hands;
• The remaining free end of the wound cord will need to be inserted into one of the recesses located in the upper part of the spool;
• Further, the same procedure will need to be done with the second piece of fishing line. It will need to be wound on the lower section of the spool;
• As in the first case, you do not need to wind a fishing line for a trimmer to the lower section. The remaining piece of thread will need to be inserted into the second groove of the spray.

After the operation performed, the coil will need to be installed on a trimmer for the grass and start it. To check the reliability of fastening the thread, you will need to press the gas lever to the end so that the engine reaches maximum speed. If the fishing line for a trimmer does not fly out of the head, then the fishing line for the trimmer is held reliably, and during the mowing of the grass it will not fly out of a braid coil.

How to wind a fishing line for a trimmer to a trimmer to grass?

The second method is a little more complicated in independent execution.

You need to wrap the cord for a trimmer for grass in the following order:

• First you need to cut off the total amount of approximately 6 m of the cord, and bend it. In this case, one of the parts should be slightly larger than the second;
• Then the thread of the place where it was bent will need to be inserted into a recess located on the dividing line between the two sections of the spool. As a result, the first part of the segment should be in the upper, and the second. in the lower section of the spool;
• After that, you need to start wrapping the fishing line. You need to do this in the direction of the arrow indicated on the corn. During winding, the cord should not be interpreted. The upper part of the segment should be neatly wound on the upper, and the lower. on the lower section of the spray. After that, two 15-centimeter segments of the cord should remain free;
• Further, the remaining ends will need to be inserted into the recesses located in the upper part of the spool;
• Then the fixed ends must be stuck into the through holes of the braid head of the trimmer for grass.

At the end, you will need to connect all parts of the mowing head, and pull each end of the fishing line a little. The finished coil will need to be installed on a trimmer for the grass and continue to work on the site.

The main stages of work

Now we start installing fishing line. There is a dividing side on the coil, which divides it into two grooves for fishing line.

This side has a groove. We measure the desired length of the fishing line, and then bend it in half (while one end should be 10-15 cm longer).

We catch the resulting loop to the groove. Next, look at the case and look for the Wind Line inscription, next to which there will be an arrow that indicates the direction of winding of the fishing line.

If there is no such inscription with the arrow, then look for the arrow on the head, then wrap the fishing line for the trimmer in the opposite direction.

Fishing winding

At the next stage, we wrap the fishing line for the trimmer, making sure that each end is in its groove. When wound. the ends of the fishing line must be temporarily inserted into the side grooves.

Then we insert the coil into the head, put the lid on top, straighten the ends of the fishing line so that they leave the grooves, and then fix everything on the latches.

Details about how to wrap a fishing line for a trimmer to the head of a trimmer for grass, you can watch in the author’s video. This review is prepared on the basis of video from YouTube Hotsem channel.