How to adjust the height of a trimmer for grass correctly. Video: how to clean the carburetor of a trimmer for grass • CIMFLOK.COM

How to put a belt on a trimmer for grass correctly

Service centers often complain about consumers of household garden equipment, who still make mistakes at the stage of its assembly and the first launch and disable equipment. Of course, there is an instruction in the package, but either it is stupidly written, or it is read after the wrong assembly, when unnecessary details were found or, worse, a breakdown occurred. Meanwhile, there is nothing complicated in the assembly of household garden equipment. You just need to be careful. Let us give an example the procedure for assembling the Stihl FS 130 lawn mower, complementing our instructions with illustrations.

You need to start the assembly with the fact that open the box and check the package of the unit. If everything is in place, then we have to put the handle to the bar with the motor, put on the belt, attach a protective casing and cutting elements.

First you need to get the handle and unscrew the barbar, which attaches the upper part of the support, without giving up the springs.

We insert the handle into the nest and fix it without tightening it. We adjust the final position after the final assembly of the lawn mower.

We put on the control knob on the handle tube and tighten the mounting bolt. For this, the kit has a universal key.

All stihl fs gas troops are located on the handle. This is: a gas lever that protects against random turned on and the lever of turning off the unit, which is controlled by the thumb. At the modification, motokos with a D-shaped handle are located next to the engine on the bar.

Put a plastic protective casing. If it is planned to use only a knife, then for its operation we use part of the casing (in the picture it is painted with orange).

If the cutting fishing line is working, then a plastic skirt is additionally put on a protective casing and a knife is placed for cutting a fishing line. In some varieties of this model, the casing can be universal or two different casings are attached to the fishing line and the other for a knife.

Putting the skirt on the casing, you need to check the reliability of its fastening. Sometimes it may be necessary to fix this protection with another screw.

Now you need to put a knife for cutting fishing line and fix it with a screw.

It remains to install the coil, having previously tucked it with a fishing line. The coil is wound on the shaft (as in the illustration) or attached with a special nut. Keep in mind that the thread on the shaft is usually the left. How to refuel a fishing line for a trimmer to a coil read in the instructions.

If a knife is required, then instead of a coil we put it. The knife is equipped with a protective lid so that during operation it does not bury into the soil. After installing it, do not forget to scroll through this cutting element and make sure that there is no backlash.

Well, the last, the easiest, stage installation on the bar of a metal clamp, t.e. suspension belt mounts.

After the lawn mower is assembled, we put on a shoulder belt or a belt parallel suspension (depending on what is given in the kit) and drive them according to the figure. Pour the gasoline mixture, start the engine and go.

Fresh Комментарии и мнения владельцев. Grass trimmer belt. How to adjust Range Grass trimmer belt

Adjust the height of the hook of the smynet belt of the trimmer for the grass with a handle of the shoulder straps so that the trimmer knife lowered to the ground is located parallel to the surface of the site (strictly horizontally). When working with a saw trimmer disk, adjust the grass The height of the hook (with a lift of the shoulder belts) so that the sawy disk of the trimmer for the grass is tilted slightly forward relative to the surface of the earth.

Moving the ear for hanging braids for grass on a trimmer belt for the grass forward or backward, equalize the trimmer for the grass so that when the steering wheel is released, the trimmer knife for the grass is near the very surface of the site, but does not go to the grass. For sawing bushes and young trees, a trimmer for the grass with a saw drive of a bureau for the grass should be equalized so that when the steering wheel is released, the car hung on the hook horizontally land. Attach.

Adjust the shoulder belts of a trimmer for grass (braids) so that the load is distributed evenly on the shoulders (check by pressing the handle of the trimmer for the grass on the hook on the hook).

The video pro Range Husqvarna grass trimmer belt. On the design features of the belt suspension (harness), which facilitate and make a more safe mowing with a motorcycle, a trimmer, a benzocosa, a Husqvarna bush and an elastic belt, quickly unfastened locks (carabiners) in case of fire or any other situation requiring a quick release from Trimmer for grass. On the universality of belts for men and women.

Such Range belts of a trimmer for grass from Husqvarna (Balance 35/55, Balance X, Balance XT) can be used on any trimmers, benzocoses, motorcycles, electric cosecs, and bureaus.

Balancing pens

For easy work with a benzocosa, you need to find the correct position of the handles. For the convenience of configuration, it is advisable to find a model with separate adjustment of the handles. In such models, the handle is attached to four screws. Up the upper screws, you can adjust the angle of rotation of the handles. Having removed the lower screws, you can adjust the hilt under your growth.

Some models of the benzos are equipped with paired handles, which do not adjust the angle of rotation. In order to prevent your feet from resting with such braids when working with such braids, they must be lowered on a working shaft. You have to bend or raise the lawn mowed to the lowered handles, so when prolonged work, the back or hand gets tired.

Constant monitoring of the tool

Prior to starting, the user is checked: the presence and freedom of rotation of a reliably fixed working equipment; stable position of control handles; Balancing the weight of the tool on belts. After all, when a benzotrimer mows, even responding to a sharp increase in the vibration of the handles, it is difficult to prevent a breakdown of the head with a fishing line or a knife.

In the work, you should pay attention to the changes:

exhaust colors (incorrect ratio of components of the fuel mixture);
power (problems with carburetor, muffler, equipment);
vibrations and sound (equipment, gearbox, clutch).

With any suspicion of non.standard equipment behavior, it is always cheaper to immediately drown out the engine.

L. Initially regulated because it is responsible for supplying fuel at low speeds;
N. is responsible for supplying gasoline at high speeds, as well as for fuel consumption and temperature;
T. With its help, simple debugging occurs.

There are options, as a rule, a carburetor of a Chinese gasoline scraper, when only one screw on the case remains to adjust. To adjust the idle. This does not mean that the module is configured automatically. This means that it will be difficult to even carry out this type of repair as a debugging. The photo shows the adjustment of the Chinese gasoline carburetor.

The module is set up only when the engine is heated: for this, the device first turns on for 10 minutes. If the braid is at idle, immediately start adjustment: turn the tint t counterclockwise until it stops rotating.
Adjustment starts with a screw l. The screw rotates to the left and right until it finds its position in which the idle speed does not become maximum.
Then turn the screw counterclockwise. This will be his work position.
The idle action should be adjusted by turning counterclockwise to increase speed, and clockwise. decrease. Its setting is to achieve a regime in which sufficient rotation is performed before the mower begins to rotate. In this case, the engine should work stably in different positions.
The position of the screw L is determined by the last. At maximum speeds, a trimmer for grass should not work for more than 10 seconds. The throttle opens, the screw rotates clockwise, very slowly, until the rotation speed decreases to the ear level.
Then the screw also slowly rotates counterclockwise until the engine starts to crawl with failures. Then the screw turns back the clock, until the engine rests normally.

If there is a tonometer, and if the product is the recommended speed of rotation in the product passport, the correction can be made more accurate, focusing attention not on the ear, but on the testimony of the device. The carburetor adjustment by a busbar on the video is made by ear

The carburetor adjustment by a busbar on the video is made by ear.

7 answers to the record “Adjusting and repair of the carburetor of the gasoline engine”

Please explain. Section 5 of the regulation of the screw L is an error? Should I read the screw a? Thanks

Tell me the initial position of the screws h l la

Thank you very much for the video about the accelerator, and I do not know, and this defect is very important and creates a huge problem that almost everyone is silent about. BRAVO….

Perhaps a tachometer. This is a speedometer, not a blood pressure meter.

The heart of any chainsaw is a two.stroke internal combustion engine.

The trimmer for grass does not belong to complex household appliances, so for the most part it is gender.

There was a need to buy reliable and accurate mechanical instructions.

The times of Soviet agro.industrial gigantomania have passed. They made a concert.

The same.based tractor is an economical version of the tractor for small work.

The Neva one.based tractor is now available in various versions, in this specialized.

How to mow a gas toss with a fishing line correctly

Is there a difference between the injection of the grass with a trimmer with a disk and a fishing line? In addition to security, there is a difference in principle of work. It is possible to work with a benzocosa with a fishing line mounted in the design on a reel in constant speed mode. This is due to the number of the following reasons:

Lines for a trimmer with a coil of 3-4 times less in weight than steel discs, so the shaft practically does not experience a load
Grass, which impresses with fishing line, is usually not high and mostly rare, which also eliminates the likelihood of a large load on the engine
The reel with a fishing line has no inertia due to the minimum weight, so when dropping gas, their rotation ceases almost instantly

From this it follows that it is possible to mow a gas station with a fishing line at constant speeds, but it is important to consider that the speed should not be higher than average. If the fishing line for a trimmer does not cope with grass, then the speed should be increased, but at the same time you need to mow in the gas dumping mode. Now we will consider the main factors that are important to consider when working as a tool:

Now we will consider the main factors that are important to consider when working as a tool:

Hold the rotating coil with a cord at a distance from the ground 10 cm if the fishing line for a trimmer does not cope with high grass, you can first mow its top, and then the lower part of the stomach is made in the direction that rotates the fishing line for the trimmer or disk

This is especially important for steel disks to take breaks, since during the operation a gas station is not only a mowing, but also the tool itself. It is interesting!Often there are questions from mowers about how much can be mowed with a benzoca on 1 liter of gasoline? There is no unequivocal answer to this question, since it all depends on factors such as the power of the tool, the type of cutter used and the type of vegetation. Now that you know how to properly mow a benzoca or a trimmer (by the way, these tools differ only in the name), you can begin to ennoble the personal plot or summer cottage

When the tool is not used for a long time, then all fuel should be drained from the tank. Indeed, with prolonged storage of oil, it is common to drop in a precipitate, which will lead to negative consequences. A similar situation with the storage of finished gasoline diluted by oil. Storing it in diluted form for longer than 2 weeks is not recommended

Now that you know how to properly mow a benzoca or a trimmer (by the way, these tools differ only in the name), you can begin to ennoble the personal plot or summer cottage. When the tool is not used for a long time, then all fuel should be drained from the tank. Indeed, with prolonged storage of oil, it is common to drop in a precipitate, which will lead to negative consequences. A similar situation with the storage of finished gasoline diluted by oil. Storing it in diluted form for longer than 2 weeks is not recommended

It is interesting!Often there are questions from mowers about how much can be mowed with a benzoca on 1 liter of gasoline? There is no unequivocal answer to this question, since it all depends on factors such as the power of the tool, the type of cutter used and the type of vegetation. Now that you know how to properly mow a benzoca or a trimmer (by the way, these tools differ only in the name), you can begin to ennoble the personal plot or summer cottage. When the tool is not used for a long time, then all fuel should be drained from the tank. Indeed, with prolonged storage of oil, it is common to drop in a precipitate, which will lead to negative consequences. A similar situation with the storage of finished gasoline diluted by oil. Storing it in diluted form for longer than 2 weeks is not recommended.

Summing up, it is worth noting that it is not at all difficult to work as a benzotrimer, and even a woman can cope with this, which proves below the presented video video. However, the tool cannot be treated negligently, since with non.compliance with safety precautions, you can get serious injuries.

Safety precautions during work

The technique of work with a trimmer with a string and a disk has some differences. So, the fishing line for the trimmer cuts the grass with the very end, but with too fast the movement is used for the entire length. As a result, the stems are not cut, and the grass is wound on the cord, which is why the engine is overloaded. Therefore, you need to choose the optimal wiring speed. In addition, when mowing high and hard grass, a fishing line for a trimmer is consumed faster than when cutting the lawn. There are several simple recommendations, the implementation of which will make mowing more efficient and effective.

It is convenient to bite the garden paths, flower beds and the edges of the Lujaiks with a trimmer with an engine below. The plane of rotation of the coil of such a device can be placed perpendicular to the ground.
Thick thickets, large weeds, bushes must be mowed with disks or special nozzles.
When cleaning large areas, the device must be tilted to the left, in the direction of scope.
To mow grass around flower beds, shrubs and other objects, you should rotate the head of the trimmer for the grass with a casing to them. So it will turn out to bake objects themselves and not damage them.

It should be remembered that the bobbin or the disk should not touch the ground and any obstacles except grass and branches that need to be cut off.

Do not use trimmers in the rain or with increased humidity.
People and animals should be at a distance of at least 15 m from the working device: trimming of grass, small garbage and stones fly out from under the cutting head at high speed and may injure.
It is better to put on the grass trimmer to a dense fabric that completely closes the arms and legs.
You need to work in protective glasses, gloves, headdress, closed shoes, special headphones or Berushas.
The wire of the network trimmer for the grass should be behind the mower.

So, the use of manual vehicles for mowing grass allows you to maintain order on a small area. It is more convenient to use a mower in vast areas. In addition, a trimmer for grass is relevant when harvesting hay and restoring order in the territory: small herbal scraps can be mulched strawberries and other useful plants. You can clearly see the mowing process with this tool on the video.

Unlike a disk. to mow a trimmer with a cord is safer, but not always optimal. As they say, it is worth choosing a cutting mechanism for the features of your work site or using complex systems, where you can operate both the disk and the fishing line for the trimmer, if necessary, installing the first or the second or the second.

It is important for the operator to understand that the length of the ends of the fishing line, which he sees in front of himself in an elongated state is exactly the diameter that will mow the device. You can read the rules for refueling the fishing line in a coil in one of our articles, but the main thing is to remember: the length of the ends of the fishing line should be optimal to conduct competent mowing

How to mow a benzoca? This must be done so that it serves you as long as possible:

keep a coil at a height of 10 cm from the ground;
when working with high grass. mow its top, and then by the stem to protect yourself from its winding to the device;
Drive the device in the same direction in which the coil rotates;
lawn grass, especially at the walls and garden decor, it is better to mow the fishing line with the tips so as not to overload the engine;
every 15 minutes take a break to the device.

Any answers to questions about braids you will find in this section of the site, but we will propose the spare parts for lawn mowers among another assortment for a benzo tool.

Ideally, high grass can be mowed with a powerful trimmer with a thick fishing line. But, you must admit, the land where weeds grow is not always even, often among landowners in plots there are shrubs and all kinds of garbage, stones. In order not to ruin an expensive equipment. it is better to produce mowing in two approaches.

In a situation, if you have to prepare grass on hay, and you are more or less oriented in a state of earthen plot-then you can more easily predict your work. Any technique intended for mowing grass can also cope with high thickets. The main thing is not to rush and competently approach the process itself, which we clearly demonstrate in practical video.

Do not overload the mechanism;
When the grass is confused, instantly turn off the device;
Do not mow moist grass even a gasoline trimmer.

Choosing a trimmer for grass and nozzles

Food. Models on batteries are convenient in that when cutting a beard, the wire does not interfere, but they are less powerful compared to working from the outlet.

Blades. Material options: steel, titanium, ceramics. The best trimmers for grass cut hairs with ceramic blades

However, it is important to take into account that the material of the knives greatly affects the cost of technology. T-shaped blades are more functional than rectangular.

The minimum length is often less than a millimeter, although it is normal to trim the beard and 3 mm. The maximum length can be 7, 10, 15 mm or more.

Nozzles. There are two main options. several interchangeable nozzles or one adjustable. Replaceable are more reliable, and adjustable allow you to set the length of the haircuts with high accuracy, but this functionality may be unclaimed. It’s great if the kit has specialized nozzles for removing hairs sticking out of the nose and ears. For these purposes, manufacturers, by the way, offer specialized trimmers for grass.

about choosing a trimmer for grass: 10 tips, which men’s trimmer for grass is better to choose for a beard and mustache

Operating principle

If we take into account the principle of the trimmer for the grass, it looks like a hand strap. The difference is that it is equipped with an engine, with its help the cutting element rotates.

Manufacturers produce the following models of mowers:

On which a gas engine is installed. Such garden tools have a fuel tank, this is their distinguishing feature.
Devices with an electric motor. These tools are easier because they do not have a fuel tank. But, choosing such models, you need to consider that you need a power source to work with them.

All electric braids can be divided into those that work from batteries and models connected to the network. Each review has its own characteristics, but they affect the power supply

If you do not take this into account, then the rest of the design is the same for different devices

If you take any model of a trimmer for grass, it consists of such elements as:

Engine;
Fuel tank (electric motors do not have this);
Levers controlled by a mower;
A knife for haircuts of grass;
Barbell;
Reel with wound fishing line used to cut grass;
Corrugated board;
Conical gearbox.

The engine is located next to the mowing head; It can be installed from below or from above. Only those models that have a direct arrow have a gearbox. If it is bent, the main bearing becomes a connecting element. It consists of 2 bushings.

The choice of cutting element depends on how difficult it is to mow grass. The most commonly used fishing line for a trimmer is called a cord. On sale there are products of various shapes, among buyers, spiral and round are in demand.

The fishing line for the trimmer is wound on the coil, it is inserted into the coil, and the 2nd end of the wires remain free. Когда двигатель косилки запускается, шпулька вращается, трава обрезается свободными концами лески.

How to cut a mustache trimmer correctly

The volume of work in this case is more modest, the preparation is simpler. My mustache shampoo, comb them with a comb.

We go to the haircut: shorten the hair with a trimmer with a nozzle and set the shape of a mustache with a device without a nozzle.

The second stage is complicated by the fact that symmetry must be observed. If you remove an extra millimeter from the edge, the corresponding mustache will become shorter. With the thickness of the mustache is a similar situation: you can easily make one mustache thinner than another. However, over time, the haircut skills are honed, there are fewer errors, it is possible to cut the overgrown mustache with a trimmer correctly. almost like in a barbershop.

Driving care is the same as for a beard. They are washed with shampoo, healed with oil. Long mustache is given the form of wax.

Interesting article: How to choose a compressor for cars: 6 dominant parameters

How to correctly configure a belt of a lawn mower for yourself

First you need to get the handle and unscrew the barbar, which attaches the upper part of the support, without giving up the springs.

We insert the handle into the nest and fix it without tightening it. We adjust the final position after the final assembly of the lawn mower.

We put on the control knob on the handle tube and tighten the mounting bolt. For this, the kit has a universal key.

Put a plastic protective casing. If it is planned to use only a knife, then for its operation we use part of the casing (in the picture it is painted with orange).

Putting the skirt on the casing, you need to check the reliability of its fastening. Sometimes it may be necessary to fix this protection with another screw.

Now you need to put a knife for cutting fishing line and fix it with a screw.

Well, the last, the easiest, stage installation on the bar of a metal clamp, t.e. suspension belt mounts.

Fresh Комментарии и мнения владельцев. Grass trimmer belt. How to adjust Range Grass trimmer belt

Adjust the height of the hook of the smynet belt of the trimmer for the grass with a handle of the shoulder straps so that the trimmer knife lowered to the ground is located parallel to the surface of the site (strictly horizontally). When working with a saw trimmer disk, adjust the grass The height of the hook (with a lift of the shoulder belts) so that the sawy disk of the trimmer for the grass is tilted slightly forward relative to the surface of the earth.

Moving the ear for hanging braids for grass on a trimmer belt for the grass forward or backward, equalize the trimmer for the grass so that when the steering wheel is released, the trimmer knife for the grass is near the very surface of the site, but does not go to the grass. For sawing bushes and young trees, a trimmer for the grass with a saw drive of a bureau for the grass should be equalized so that when the steering wheel is released, the car hung on the hook horizontally land. Attach.

Adjust the shoulder belts of a trimmer for grass (braids) so that the load is distributed evenly on the shoulders (check by pressing the handle of the trimmer for the grass on the hook on the hook).

Such Range belts of a trimmer for grass from Husqvarna (Balance 35/55, Balance X, Balance XT) can be used on any trimmers, benzocoses, motorcycles, electric cosecs, and bureaus.

Preparation of Balance XT belt equipment to work with a Husqvarna travo.wrapper

You need to start the assembly with all additional details to open the box and check the set of the unit. If everything is in the workplace, then we have to put a handle to the bar with the motor, put on the belt, attach a protective casing and cutting elements.

2.four. At first it is necessary to get the handle and unscrew the vint-bar, which strengthens the highest part of the support, without giving up the springs with all this.

We insert the handle into the nest and fix it without putting it in a long box. The final position is adjusted after the final assembly of the lawn mower.

We put on the control handle on the handle pipe and tighten the mounting bolt. For this purpose, the kit has a universal key.

Our client remains the controls of the Stihl FS 130 benzo.core are located on the handle. This is: a gas lever that protects against random turned on and the lever of turning off the unit, which is controlled by a huge finger. At the modification, motokos with a D-shaped handle, controls are located next to the engine on the bar.

Putting the skirt on the casing, you need to check the reliability of its fastening. If you need to fix this protection with another screw.

It remains to install the coil, after refueling it with a fishing line. The coil is wound on the shaft (as in the illustration) or is attached with a special nut. Have because the carving on the shaft is usually the left. How to refuel a fishing line for a trimmer to a reel read in an annotation.

And the last, simple, step. installing an iron clamp on the bar, t.E. Suspension belt mounts.

How to clean, adjust, and fix common carburetor problems on a Stihl FS90 trimmer weedeater

When the lawn mower is assembled, we put on the shoulder belt as it is also called the belt satchery suspension (looking at what is given in the kit) and adjust them according to the figure. Pour the gasoline mixture, start the engine. and go ahead.

Adjust the shoulder belts of a trimmer for grass (braids of the harness) so that the load is distributed moderately on the shoulders (check by pressing the handle hook of the trimmer for the grass).

Such Range belts of a trimmer for grass from Husqvarna (Balance 35/55, Balance X, Balance XT) are used on all trimmers, benzocoses, motorcycles, electric cosecs, and bureaus.

When you need to brush your teeth: before breakfast or after? Probably a person knows that you need to brush your teeth twice during the day. Imagine for yourself morning without

How to faithfully brush your teeth to the dog at home hello! I am Kulkova Nadezhda Petrovna, senior veterinarian, special for veterinary dentistry

How to correctly clean the pomegranate from the skin. Video Description: In hot and solar Georgia, there is such a custom: if the guy is in love with the lady,

We brush our teeth correctly at the current time there are both general and personal advice on the correct cleansing of the teeth and the oral cavity. At the same time, the question of how long it is necessary to clean

There are trimmers for grass, for which additional devices are not needed. for example, light electrochemers on batteries. Even a child can tolerate them, and they are firmly lying in their hand without breaking. But in most cases, trimmers for grass weigh from 6 to 9 kg, and in order not to tire about to transfer them from one place to another place, you need a belt.

1) for transporting a trimmer for grass. Transport a trimmer for grass to the country when there is no car, a difficult business. If the equipment does not have a belt, then at least a cover with a belt over the shoulder should be sewn. This will facilitate the load when transporting a trimmer for grass.

2.4) for comfortable mowing of grass. After all, if the hands are tired, then the weeds and the overgrown lawn will be lazy to mow. If you want, then the hand trembling with lethargy is a dangerous option.

3) for the ergonomic position of the trimmer for grass relative to the body. The belt is correctly fastened and adjusted to the length of the back of the lower back and overstrain of the muscles of the back.

The choice of nozzle

The set of trimmers includes several different nozzles. changing them, you can achieve the optimal vegetation length on the face. A step of a few mm allows you to choose the necessary head for various types of beard and mustache.

Some models are equipped with only one nozzle. a special wheel and a fixer are intended to regulate the length of the hairs.

1-10 mm. Such nozzles are used to work with bristles and haircuts of a beard. they provide optimal length, cut off the hairs well.
11-20 mm. If such nozzles are included in the machine, then they are designed to cut hair on the head.
Shaving without nozzles. Many trimmers for grass are equipped with this opportunity. this is necessary to create clear contours or shaving everything to smoothness.

The minimum step allows you to configure the length of the hairs in the most accurate way.

The main problems

Malfunctions of the carburetor Motokos or trimmer for grass, despite the relative simplicity of their elimination, sometimes require a long search by excluding. The main reasons are as follows:

Flamming fuel supercharger

The most repeating breakdown is wear, rupture of the membrane. As a result, its lavation. Fuel moves are not sealed at certain stages of the engine cycle. The reasons here are as follows:

You have been working on a motorcycle or trimmer for too long without a break;
Poor.quality fuel was seasoned;
Wheelled gases fall into the pulse channel.

A deformed membrane is fraught with several bad consequences:

not enough gasoline or oxygen in the created combustible mixture;
the launch of the motor occurs after 10 or more unsuccessful attempts;
the engine knocks, clats during operation, and t. D.;
The working piston is deformed.

Ground of a mesh filter

The reasons for the clogging of the mesh filter are poor.quality fuel cleaning, damage to the hose and/or the injection head.

The failure of the adjustment lever

Wear of the contact edge of the lever. a consequence of not completely purified fuel, into which grains of sand or particles of clay, metal or other inclusions that are not soluble in liquid hydrocarbons fell. A problem with fuel injection appears, the motor does not function with interruptions without load.

The inlet needle is spoiled

The inlet needle breaks due to the presence of metal and stone particles in gasoline. As a result, the saddle of the intake needle tightly adjacent to it, the fuel mixture flows. In the combustible mixture created by the carburetor, there is too much air, which is why the motor can “sneeze” during operation. Finally, the needle can stop due to poor-quality gasoline, or the unit was idle for a long time.

Clogging the adjusting space

Deposits may accumulate in the adjustment compartment. The needle does not completely cover the hole, and a lot of gasoline enters the fuel chamber. the motor pours it, perhaps floods the spark plugs. Because of this, the gasoline mixture contains an increased number of vapor of gasoline. The efficiency falls noticeably.

The adjustment membrane is spoiled

The membrane is often deformed (sometimes torn) due to continuous operation of motorcycles or trimmer for grass for several hours. If you abuse such a “shock” mode of operation, damage to the membrane occurs more often. New breakdowns will be sprinkled from a cornation of abundance:

the piston will break;
The number of attempts by the unsuccessful start of the engine will increase sharply;
The fuel mixture will contain too little gasoline;
Useful (thermal) power will drop sharply.

The inlet regulatory lever sees

Sequeling of the adjusting lever. a consequence of the incorrect installation, random flexion. Contactive line will find an incorrect position. This will violate the additional injection of gasoline.

The damper has worn out

Throttle and air conditioning are unusable due to admission to the air flow of dust, metal particles, etc. D. Damaged shutters are similar to details subjected to streaming with sand. Due to wear of the damper, the efficiency of the motor decreases, breakdowns are detected. The piston and cylinder wear out.

In some cases, this filter is simply not suitable for your model motorcycles or trimmer for grass. In the end, the shaft of the motor will suffer. its pieces fall into the engine channels, which is why the piston will be broken.

Weed-eater Single Adjuster Screw Setting. This happens Inside the Carburetor when Adjusting!

The carburetor cannot be adjusted

The fact that the adjustment is too rough (it is not possible to accurately set the parameters) are to blame for the adjustment screws. The manufacturer Motokos or trimmer for grass can put excessively thick and hard springs. You can find others either in workshops where such equipment is repaired, or purchased from any dealer or official representative of the company who released the engine for your trimmer for grass or mechanical braid for grass.

The primer broke

Primer-a manual mini-pump for forced swinging fuel into a carburetor. For a successful start of the motor, it may be necessary to pump 20 ml of gasoline manually.

General characteristics of a trimmer for grass

The trimmer for the grass is presented on store shelves in the form of a small electric device designed to cut the hairs in different parts of the body, including shortening hairs in the intimate zone of men and women, ears, nose. With such a device you can get rid of hairs even in hard.to.reach places of the body, while the vegetation is removed evenly.

Two types are divided into two types, if you look at the type of operation of their electric motor:

Rotary. Are powerful, durable. Can last a long period without breakdowns. This is their main advantage. Suitable for professional use.
Vibrational. Engine operation is somewhat weaker in power, every half hour he needs a break. But for home use are suitable.

Devices have differences in design, manufacturer, numerous additional functions. Some devices are able to maintain several modes. this is usually delicate/intensive. In demand, models with a vacuum function are in demand, it is required to suck in a shaken vegetation. This is very convenient, because after the procedure you do not have to clean the working area from the abundance of hairs.

The best models are those that can at a minimum shorten the hair. There are differences in the method of cleaning the device, for example, most models can be washed under ordinary water, without afraid to harm the mechanisms inside. By type of power, the device happens:

Options with batteries are suitable for those who travel, since they are distinguished by their compactness. The speed of the device directly depends on the strength of the charge. Usually it takes about six hours to charge the battery. The network type of power is referred to budget options. But they are durable and powerful. And the combined model combines the advantages of both devices.

Belt setting

To ensure the conditions of comfortable work, you need to be able to wear a rug belt correctly. This process requires a certain dexterity, but then, after adjusting the satchel for itself, it will be much faster and easier to worry.

Hook height adjustment

The most important thing is to adjust the belt so that the trimmer for the grass is at the right level from the surface of the earth. To do this, raise or lower the height of the hook, which is carried out by pulling the shoulder belts until the holder is lower than the hips by 10-15 cm (palm width). In this case, the knife of the attached braid for the grass should be parallel to the surface, that is, in a strictly horizontal position.

Bowling braids for grass by moving the ears

After fixing the necessary heights under yourself, you need to balance the trimmer for the grass. To do this, the ear is rearranged, with which the device is suspended to the belt, forward or backward. As a result, you need to attach the belt to the trimmer so that when the steering wheel is released, the knife or saw disk does not lie on the ground, but hung above it without touching the surface. At what distance will it be dependent on the goals set.

Adjusting shoulder belts

So that the load is distributed evenly on the shoulders and back, you need to adjust the shoulder belts well. To do this, just tighten or relax the straps. they should not dig into the body or hang. You can understand how the weight will be dispersed, if you press with your own hands on a hook for suspension braids for grass.

Fixing the lawn mower on the belt

Depending on the model, a gasoline braid can be mounted on a belt using a bar or loop. In the latter case, for balancing, you need to move it along the rod to get the necessary result. In some cases, depreciation mechanisms are provided, which allow you to smooth out vibration and soften the sharp surges of the trimmer for grass.

Balancing pens

An important stage in the configuration of a ranger belt is also adjusting the handles to the optimal level. When the operator holds the motorcycle, his hands should be relaxed, and the shoulders are parallel to the body. Therefore, after fitting a biceps belt, the two.handed mechanism should be adjusted by moving it up or down. It is necessary to achieve such a result that the hands only set the direction, and not hold the device. If after that the balancing of the trimmer for grass is again violated, then you will have to re.repeat all the stages.

How to dress a belt from a trimmer for grass priority

Features of the external elements of the lawn mower

The bar is the main conductor, combining the motor into a single design and the cutting system. There is a shaft in its cavity, which is flexible or straight. The bar can understand, due to which it is much more convenient to store. The design of the shaft determines its shape. Direct shaft is more reliable for the bar. True, if the landscape of your site differs in height in different places, it is better to purchase a trimmer for grass with a curved shaft.

Experts advise paying special attention to whether the bar is collapsible. If so, then you can easily fold it for storage

Belt setting

Balancing pens

Hook height adjustment

On a note! If the trimmer for the grass is attached too high, then this will greatly limit the capture of the grass.

Fixing the lawn mower on the belt

The belt is easily adjustable for a particular face of any face, thanks to adjustable belts in height and width (you can tighten or loosen)

Sending spare parts can be carried out to any city and region of Ukraine: Cherkasy, Zhashkiv, Shpola, Chigirin, Smil, Uman, Monastery, Lysyanka, Buki, Zvenigorod, and others.

Sources:

https://101benzopila.ru/kak-pravilno-odet-remen-na-trimmer/
https://101benzopila.ru/kak-otregulirovat-trimmer-po-rostu/
https://molibden-wolfram.ru/kak-otregulirovat-trimmer-po-rostu/
https://domdetaley.ru/kak-otregulirovat-trimmer-po-rostu/
https://labequip.ru/kak-otregulirovat-trimmer-po-rostu/
https://101benzopila.ru/kak-pravilno-nastroit-trimmer-pod-seba/
https://molibden-wolfram.ru/kak-pravilno-nastroit-trimmer-pod-seba/
https://domdetaley.ru/kak-pravilno-nastroit-trimmer-pod-seba/
https://101benzopila.ru/kak-pravilno-odet-remen-na-trimmer/