How to cut thick foamy figure. • CIMFLOK.COM

Than and how to cut foams at home: review of methods and stages

Engaged in assembling kitchen stools, I thought why not make sitting soft. But in order to create such a kind of upholstery, I faced the question of how to cut foams very exactly at home. Indeed, for the finish covering of the seat, you need to be able to correctly cut the fragment in accordance with the size. In this post I will tell in detail about the process.

Furniture manufacturers use special machines. You can cut polyurethane foam of any thickness, with a perfectly flat seam and accurately observing the size.

Naturally, these options are not entirely suitable for home: especially when you need to cut a couple of sheets to restore furniture and never do it again.

In such cases, it is recommended to use the so.called “loaf” (with zazubins on the blade). Its shape and length allows you to make an even section of thick polyurethane foam. It will have to be cut for a long time, but as a “one.time action” the method is quite suitable.

Please note: in no case do not listen to the advice of the “craftsmen” and do not cut the foam rubber with a wire (tungsten or nichrome). Heating foams leads to the release of phosgen. toxic gas. It is extremely dangerous to inhale it in a closed room.

Drawing up a project

For example, we have determined that a double.sized shredder with a low rotor rotation frequency is suitable for production tasks.

His project necessarily includes:

engine selection by power;
calculation of the gear ratio of the gearbox and the choice of the factory model;
determination of the diameter and length of the rotors (according to the size of the loading window);
calculation of shafts for strength;
The choice of bearing supports.

For this you will need the textbook “Parts of cars” for universities. You will also have to look into GOSTs according to threaded connections, reference books on gearboxes, bearings, couplings and other assembly units.

This must be taken into account when you assign the dimensions of the groove.

After calculations, it is necessary to make a layout of nodes on a millimeter paper or in an AutoCAD type editor, determine the dimensions of corps parts and beds.

This task must be approached responsibly so as not to miss anything. Sometimes the protruding head of the “unaccounted” bolt leads to the fact that the car has to be redone. After that, a detail is made. the drawing of each part separately.

What is polystyrene and why it is used

Foam sheets

Foam white material, which is almost entirely of the air. It is used for packaging equipment, food, as thermal insulation and soundproofing material, as the basis for the manufacture of household items, logos and many other things. One of the main advantages of polystyrene is its cheapness. Many buy it in order to make some product from this material and profitably sell it. But even a simple person will be very useful, because you can make a lot of things for the home from it. The main thing is to be able to work correctly with the material, as well as choose it for specific purposes.

Gluing and cutting foam. how and how to cut foam

Polyurethane foam. material with a porous structure, high elasticity, soft and inexpensive. It is most often used to fill mattresses and as furniture stuffing. If there is a desire to pull the furniture or make a mattress with your own hands, there is a problem: how to cut foams at home and how to glue it? There are several recommendations for craftsmen.

Here are some examples

If the first cutter turned out to the entire width, it is necessary to gently expand the edges of the cut, deepen the knife and make the last cut. As soon as you hear the rattle of the knife blade on the cardboard, it means that you coped with the task.

DIY foam cutting is a difficult task, but real. To make the edge extremely even, it is necessary to use a knife with a very sharp and long blade. If the knife began to cling or began to tear the foam. it is time to replace the blade or undermine it. But it is better not to wait until the last, but immediately take care of the timely replacement.

Curly cutting foam is no different from the straight line. But the angle of inclination towards itself must be maximally increased, otherwise the cut parts will have a little oblique edges. There is nothing complicated in such cutting, the main thing is to stock up on patience and high.quality knife. Also for curly cutting, you can use a special saw for foaming Bosch GSG-300 Professional.

Foam Cutting Types For Industries; How to Cut Foam

It is such a foaming saw that is in our arsenal and we can easily cut the sheets of foam rubber for you 30 cm thick. The quality of the cut is wonderful, everything turns out perfectly evenly and perpendicular. Cut the figures of various shapes a rather entertaining and interesting activity.

Cork panels

This leaf material is made of cork oak wood. He is in use in the manufacture of traffic jams for wine bottles. A wood veneer or small crumb is used, which is pressed and glued at high temperatures in solid sheets. The veneer is more expensive, baby is cheaper.

Manufacturers guarantee noise reduction by 20-30 dB, which is not entirely true. Yes, such indicators will take place. At the neighbors. The cork coating protects against shock noise, so those who live a floor below will be content with silence. In the apartment on top, where the cork lies on the floor, it will still be perfectly heard how satisfied the neighbors if they begin to discuss it out loud.

Ease.
Strength.
Small thickness.
Easy to cut and mount.
It absorbs moisture poorly.
Crumb sheets are cheap.

Among the obvious minuses, only one can distinguish. at least effectiveness in the fight against extraneous sounds. Innovative materials for the installation of the leveling screed are designed to solve this problem.

Scheme: on a dry screed

Suitable for cases when you need to do sound insulation, but there is no desire to mess with the solution and wait 3 weeks until it dry completely. The alternation of the layers of the “dry acoustic pie” may differ. For a dry screed with exped clay, vapor barrier is needed, for a more modern vibration material. no. Consider a more modern option:

Primer. It is needed for good adhesion of granular noise plastic with walls and floor.
Noise plast. This is a vibration base (absorbs shock noises up to 32 dB), so you do not need to glue the walls with a bromatic tape. You can do this for insurance, but there is no need. Noise plast is lined so that it enters the walls, above the final coating level. Layer height. 5–20 cm.
Reinforcing mesh.
GVL sheets for aligning the surface. Are laid in two layers. The layers are glued together with mastic and fixed with self.tapping screws;
Switch sealing with putty.
Flooring.

Second stage: laying materials in layers

The foundation. If the materials are slab or roller (except membranes), they need to put vapor barrier under them. This is a thin PVC film, which is laid for 15–20 cm and glued with construction tape at the junctions. It protects materials from condensate due to overheating from below. If these are vibration materials, instead of vapor barrier, you need a primer.
Installation of the brown tape along the edge of the walls.
Soundproofing. Membrane, sheets or filling.
Reinforcing layer. For noise plastic and cement, this is a steel grid, for sheet materials. a layer of plywood.
Aligning layer. This is a durable and smooth material: plywood or GVL.

It can be single, but more efficiently to do double.

Gluing and cutting foam. how and how to cut foam

Here are some examples

Cork panels

Ease.
Strength.
Small thickness.
Easy to cut and mount.
It absorbs moisture poorly.
Crumb sheets are cheap.

Scheme: on a dry screed

Primer. It is needed for good adhesion of granular noise plastic with walls and floor.
Noise plast. This is a vibration base (absorbs shock noises up to 32 dB), so you do not need to glue the walls with a bromatic tape. You can do this for insurance, but there is no need. Noise plast is lined so that it enters the walls, above the final coating level. Layer height. 5–20 cm.
Reinforcing mesh.
GVL sheets for aligning the surface. Are laid in two layers. The layers are glued together with mastic and fixed with self.tapping screws;
Switch sealing with putty.
Flooring.

Second stage: laying materials in layers

The foundation. If the materials are slab or roller (except membranes), they need to put vapor barrier under them. This is a thin PVC film, which is laid for 15–20 cm and glued with construction tape at the junctions. It protects materials from condensate due to overheating from below. If these are vibration materials, instead of vapor barrier, you need a primer.
Installation of the brown tape along the edge of the walls.
Soundproofing. Membrane, sheets or filling.
Reinforcing layer. For noise plastic and cement, this is a steel grid, for sheet materials. a layer of plywood.
Aligning layer. This is a durable and smooth material: plywood or GVL.

It can be single, but more efficiently to do double.

Drawing up a project

For example, we have determined that a double.sized shredder with a low rotor rotation frequency is suitable for production tasks.

His project necessarily includes:

engine selection by power;
calculation of the gear ratio of the gearbox and the choice of the factory model;
determination of the diameter and length of the rotors (according to the size of the loading window);
calculation of shafts for strength;
The choice of bearing supports.

This must be taken into account when you assign the dimensions of the groove.

After calculations, it is necessary to make a layout of nodes on a millimeter paper or in an AutoCAD type editor, determine the dimensions of corps parts and beds.

How to cut foams

Hello everyone, just recently I had a problem, how to cut off the foam rubber evenly, and at home. For all the time of passion for carpentry, I have never encountered foam rubber, it is understandable, I usually work with woods.

Since cut off foam? And what you need to do. The first thing that came to my mind was some kind of expensive machine that it is simply not realistic to buy, since I once cut a foam, but for a very long time, and I didn’t really succeed.

At work, in the next workshop, they are engaged in upholstered furniture, and somehow, at lunchtime, I met a guy who is engaged in this Street. During the conversation, I found out that in order to cut off foam, they use the knife, and they have no expensive equipment for this. We talked and he told me how to cut off foam gently at home.

To cut off foam rubber will need the following

A sharp knife, best is the chancellery or for cutting linoleum
A felt.tip pen or a marker with a thin rod
Cardboard or something else for the base
Good ruler

Next, to cut off foam, it will be necessary to prepare the base. As a basis, many advise you to use a plywood or a wood-piece plate. I would not advise you, because when you cut a foam rubberle with a knife, the tip of the knife will dull about this plywood. Therefore, for the ground, I advise you to use cardboard. By the way, I forgot to say why the base is needed, the base serves so that the floor or another base does not spoil, on which you are going to cut off the foam rubber, well, and as you understood for protecting the tip of the knife.

Well, the last point how to cut off foam, this is the process of cutting. To do this, take a very sharp knife. Your kitchen knife is clearly not suitable here, since his blade is thicker. Therefore, I advise you to use a stationery knife, or a construction knife, like those that cut linoleum. It is very important that the blade and the tip are sharp, otherwise you can’t get a foam rubber.

Well, then go to work, spend exactly along the line with a knife, preferably without using the stop, since the emphasis will be pressed on foam, thereby creating a load in it, and the knife will be poorly cut. If you doubt your abilities, then it is better to practice a little on another piece of foam rubber so as not to spoil the workpiece.

Anyway, foam rubber is usually cut in order to sheathe up her upholstered furniture. Therefore, you can not do perfectly evenly, and you can’t get 100% exactly cut off exactly. The fabric will still be on top of the foam, which will smooth out all the irregularities and errors of the cut.

Here I am an article, it may be useful for those who have thought about cutting off foam at home with your own hands. I will be glad to Комментарии и мнения владельцев, tell us what you think about it, and if there is experience, share it.

Often you can find advice that foam rubber should be cut with a heated nichrome wire connected to a voltage of 12 V, as well as a heated soldering iron.

How to cut smoothly thick foam at home?

However, at home, this is not recommended, since foam rubber distinguishes harmful substances into the air, which, even in small doses, are highly toxic and affect the respiratory and nervous systems of a person. We will not risk health, especially since foam rubber is well cut by an ordinary knife.

Mark a piece of foam rubber with a marker or felt.tip pen, while putting small marks. Combine the tags together in a ruler (you can use a flat bar).

Under the place of the future cut, put a piece of boards, plywood, wood-boring plate or just dense cardboard. This will protect the floor from damage during cutting.

Cutting foam is recommended without a ruler. Spit with a strong and accurate movement with a knife according to the marking you made. At the same time, hold the knife vertically.

If the foam rubber does not cut through to the end, spread the cut part with your fingers and cut the foam to the end with the second reeza.

If the cutting is obtained, this means that the knife blade has become dull. Break the tip of the blade or replace it with a new.

Curved cuts are made according to exactly the same technology. Mark the pattern, then cut the foam along the line, making sure that the knife does not fill up, but is located vertically. The quality of the cut will not be perfect, but it will be quite fit if you need to cut out a pillow for upholstered furniture, which will then be covered with fabric.

Pre.soaked thin foam is much easier to cut with scissors.

How to cut foams?

It would seem that the question? Take it and cut. There are no problems with a material up to 5 cm thick.

Than cutting exactly thick foam?

But how to make an even section of a 10-centimeter or even thicker foam?

In the vastness of Internet forums, advisers are actively offering pretty bold ways. For example, heated tungsten or nichrome wire. over, the craftsmen are advised by connecting the wire to electricity with a voltage of 12 V. Choose, they say, the temperature so that it does not burn, but cut. Here right here. Stop! Porolon-Optom store.RU considers it his duty to warn that this method of cutting polyurethane foam materials, and especially at home, is dangerous to human health. The chemical reaction between heated wire and foam rubber is accompanied. With normal contact of foam rubber with fire, this will not happen, the material is not fuel and environmentally safe. But chemical experiments of self.taught that have not read the textbook on chemistry should not become an example to follow.

What to look for

Foamen is not just a type of plastic, but a plastic with the addition of various kinds of chemical impurities, toxic polymers that give this material porosity.

At room temperatures, foam rubber is absolutely harmless to a person, but you only have to undergo a heating material, as it immediately becomes toxic. Therefore, it is impossible to use foaming at home, as some amateurs, heated metal thread or wire advise.

The foamed sheets are so cut in production, but workers must use protective masks, and powerful ventilation is mounted in the production workshop where this operation takes place.

Ordinary household scissors are also not assistants for cutting foam. The edges of the material, cut in this way, lose their porous structure.

So how to cut? Here are what tools are needed for cutting foam:

We use cardboard or plywood for lining to save the surface of the table or floor where this operation will be performed;
a building knife with adjacent blades;
ruler or template;
cutting marker.

What is the problem with scissors?

The problem is that when cutting with scissors, the structure of foam rubber is disturbed along the edges of the cut. The edges are applied and are no longer straightened to the original position. So scissors for even cutting are not suitable either.

So, how to cut foams at home, so that the edges are as smooth and close to what is obtained during production cutting? To do this, you will need to prepare the following tools and consumables:

Actually, the foam itself, which we are going to cut.
Lining for foam rubber we will cut. It’s clear that if we decompose it on linoleum or on the floor of the apartment, these very materials will end, since they will all be in scratches from the knife. In the role of lining, it is best to use a sheet of plywood with a cardboard laid on it, so that the tip of the knife does not dull about the hard plywood. Cardboard can be used by dismissing any cardboard box of a suitable size.
It is advisable to have a knife from the category of construction. They are also called knives for cutting linoleum. He includes a whole clip of removable blades, which in the event of a gear can be changed. It is better to use a branded European rather than a Chinese knife, since the steel of the “Chinese” is low.quality, and such a blade will dull after the first wiring.

Cutting instructions

If you follow the instructions in everything, your foam rubber will be delivered perfectly. So, let’s go:

Since we still decided to cut the foam rubber on the lining, and not on linoleum or parquet, first we put it. First plywood, then a sheet of cardboard.
Lay the foam layer on top that we want to cut. We make sure that the fishing line for the trimmer of the future section is on the lining.
We take a ruler and, in accordance with the specified dimensions, draw a fishing line for a trimmer along which the future incision will pass.
We remove the ruler. If we cut along the ruler and pressing it at the same time, then the section will turn out even, but the edge will be as pressed as in the case of scissors. If you decide to cut it on a ruler, then in no case do not press on it.

Good advice on how to cut foams, so that the edge is perfect. If you feel that the knife began to make peculiar hooks during the wiring, it means that in some place the blade was dull and, without cutting out, begins to tear the foam rubber, forming a strip of foam grouse. In this case, you should immediately change the blade to a new. It is best to do this without waiting for this to happen. Made five to six wiring, changed the blade. They can then be used again for any other purposes, but for cutting foams they will already be unequal. Simple cutting of foams with a knife is clearly given in this video.

Gluing and cutting foam. how and how to cut foam

Upholstery Basics: How To Cut FoamWith a Bread Knife!

How to cut foams at home: a list of necessary tools

To cut foam and make its edges extremely even, it is necessary to stock up on special tools and consumables. Among them:

lining. it will help protect the surface from scratches that occur during cutting. A plywood sheet supplemented with cardboard is suitable (a cardboard box will fit in a laid out state);

Building knife or other knife with a long blade. Additionally, buy a set of removable blades to easily change them after wear. Remember that high.quality knife is the key to the success of cutting foam. So buy models of the average price segment;

If you need a figured cutting, you need a cardboard template with a cut pattern;

marker. with it, you can outline a fishing line for a trimmer cut.

How to cut furniture foam: instruction

If all the materials and tools are at hand, you can proceed directly to the process. Compliance with cutting technology will achieve an ideal result. How easy it is to cut foam. complete instruction:

Put the plywood, wood-fiber plate on a flat surface (for example, floor), and place a sheet of cardboard on top of it on top of it.

Lay the foam plaster on top of the cardboard so that the place of the future section is on the cardboard and does not go beyond its edges.

Using the ruler, draw a fishing line for a trimmer along which you need to make a cut. Cutting can be made under a ruler if the length of the knife blade allows.

Having taken the knife, configure the required length of the blade. Then make a small incision on one side. After insert the knife into the starting fishing line for the trimmer of the cut and make confident accurate movement. The second hand at this moment slightly grab the edges of the foam block. Cutting foam at an angle is the best solution that allows you to make a cut as even as possible.

We also have different stamps of foam rubber on sale. Everything is available at a store in Kyiv. Look at our foaming catalog. you are sure you will find a suitable for you. We will provide an exhaustive consultation on the choice of foam.

Here are some examples

You can order the cutting and gluing of foam rubber on our website by going to the card of the services that interests you. The cost of cutting is indicated for the linear meter, and the gluing. for the square.

How to cut foams at home

Foamen. modern material that distinguishes softness, convenience, hypoallergenicity. It is used as a filler for mattresses, furniture, is made of different densities and thicknesses.

Now foaming can be bought in specialized stores. There they will help you cut it to the desired size. But if you decide to do this at home, you need to know several rules.

What to look for

Foamen is not just a type of plastic, but a plastic with the addition of various kinds of chemical impurities, toxic polymers that give this material porosity.

The foamed sheets are so cut in production, but workers must use protective masks, and powerful ventilation is mounted in the production workshop where this operation takes place.

Ordinary household scissors are also not assistants for cutting foam. The edges of the material, cut in this way, lose their porous structure.

So how to cut? Here are what tools are needed for cutting foam:

We use cardboard or plywood for lining to save the surface of the table or floor where this operation will be performed;
a building knife with adjacent blades;
ruler or template;
cutting marker.

Cutting process

We free up the place, remove all the things that may interfere.
We place a sheet of foam rubber. Celebrate the fishing line for the cutting trimmer using a ruler and marker.
We take a knife with a blade of the desired length (over the width of the foam) and carefully make an incision on one side.
We tilt the plane of the blade to us to make an even section.
If the blade clings to foam rubber, then it is dull. Then it must be changed, otherwise there is an opportunity to spoil the material.
In the case when you could not cut the thick sheet of foam rubber, do not worry. Spread your hands fishing line for a cutting trimmer, put a knife and draw again.

In order to do figure cutting, it is worth acting absolutely the same. Only as much as possible increase the angle of inclination of the knife to you so that the bending lines are even.

To cut the material such as foam rubber, purchase everything you need and be patient.

1 comment: how to cut foams at home

I thought that it was yourself to cut foams, at home. it would be difficult. But, judging by the description in the article, everything is quite simple. We will try.

How to cut furniture foam: instruction

If all the materials and tools are at hand, you can proceed directly to the process. Compliance with cutting technology will achieve an ideal result. How easy it is to cut foam. complete instruction:

Put the plywood, wood-fiber plate on a flat surface (for example, floor), and place a sheet of cardboard on top of it on top of it.
Lay the foam plaster on top of the cardboard so that the place of the future section is on the cardboard and does not go beyond its edges.
Using the ruler, draw a fishing line for a trimmer along which you need to make a cut. Cutting can be made under a ruler if the length of the knife blade allows.
Having taken the knife, configure the required length of the blade. Then make a small incision on one side. After insert the knife into the starting fishing line for the trimmer of the cut and make confident accurate movement. The second hand at this moment slightly grab the edges of the foam block. Cutting foam at an angle is the best solution that allows you to make a cut as even as possible.

Foam. universal material. It is used in many large industries and in needlework. Differs in a porous structure, elasticity, softness and attractive cost. When working with Furniture Furniture in domestic craftsmen, especially those who did not use it before, two questions arise: how to carefully cut and firmly glue the details from this material among themselves. The secrets of how to do this correctly, quickly and reliably shared the masters of Vinyl Text. Cutting foams to cut evenly and without a bully foam.free for a sofa, chair, aunts or armchairs, stock up:

A sharp knife: stationery or for cutting linoleum;
marker or felt.tip pen;
thick cardboard, plywood or a piece of board under the base;
wooden rail or ordinary ruler, pattern (for curved cuts).
Select a place for laying out a sheet of foam and put a thick cardboard or a piece of board under the material so that when cutting, do not spoil the base (floor, countertop);
Make a pitch or marker with a felt.tip pen or marker and connect them using a rail or ruler. For a cut under the radius, use a template or pattern;
Take the knife and, holding it strictly vertically, with a strong, confident movement, spend on marking. Do not use the ruler when cutting, since it will put pressure on the foam rubber under the weight of the hand, crush it, and the cut will eventually turn out to be uneven;
If the foam rubber does not cut through to the end, spread your fingers with the “processed” site and bring the work to the end to the end. When the bullying appears, break the blade of the clerical knife or replace it.

Than and how to glue foams for working with foam rubber, contact adhesives are suitable for butadiene-stirol, polyurethane, non-repteenial basis. The most popular and budgetary of them are: BF-6, glue 88, Rapid-100. They are safe for health (do not exude toxins), easy to use and reliably fasten the foam parts among themselves. Gluing technology:

Lubricate the edges of the prepared parts with glue using a roller, brush or spray gun. Economy option. a gun, the consumption of the composition is about 70 grams./cm.sq.;
Wash the time specified in the instructions;
Connect the details, pressing tightly or pressing the press, until a reliable, even, elastic seam is formed.

Vinyl Text company: Furniture foam for a sofa and other upholstered furniture, as well as upholstery materials, accessories in retail, wholesale and delivery to all regions cut thick foams: Instructions

To organize the working process, you will need a lining (usually a sheet of plywood is used, and a laid out cardboard box is laid on it). You also need to find a long ruler, as well as a marker or packaging tape for marking. A sharp building knife is also useful. Then you need:

Lay a leaf of polyurethane foam on a lining. Make sure that the fishing line for the trimmer of the future section is on cardboard.
Mark a fishing line for a trimmer with a marker or tape.
Put the ruler along the line and carefully, holding the knife under the slope, outline the incision in the corner.
Continue to saw, adhering to the markings and using the ruler for this.
If there is no certainty in your own accuracy, you need to put two even wooden strips along the line line, leaving a gap for the knife movement.
Having made the cut to the lower part, you can take a construction knife and cut the halves completely with one precise movement.

Figure cutting of thick foam rubber in this way is difficult to carry out. It is more suitable for straight lines. Complex elements can be cut only using a special tool. You can order a cut of foaming for the desired dimensions in this store https: // intustyle.com.ua

How to cut off the foamer hello to everyone, just recently there was a problem in front of me, how to cut off foamines evenly, and at home. For all the time of passion for carpentry, I have never encountered foam rubber, it is understandable, I usually work with woods. Since cut off foam? And what you need to do. The first thing that came to my mind was some kind of expensive machine that it is simply not realistic to buy, since I once cut a foam, but for a very long time, and I didn’t really succeed. At work, in the next workshop, they are engaged in upholstered furniture, and somehow, at lunchtime, I met a guy who is engaged in this Street. During the conversation, I found out that in order to cut off foam, they use the knife, and they have no expensive equipment for this. We talked and he told me how to cut off foam gently at home. To cut off foam rubber will need the following

A sharp knife, best is the chancellery or for cutting linoleum
A felt.tip pen or a marker with a thin rod
Cardboard or something else for the base
Good ruler

So, how to cut off foam rubber, first using a marker, make the cut line on foam. If these are straight lines, it is better to use the ruler, if you should have a cut under the radius, it is better to use some kind of pattern, template or other device in order to draw exactly the radius. Next, to cut off foam, it will be necessary to prepare the base. As a basis, many advise you to use a plywood or a wood-piece plate. I would not advise you, because when you cut a foam rubberle with a knife, the tip of the knife will dull about this plywood. Therefore, for the ground, I advise you to use cardboard. By the way, I forgot to say why the base is needed, the base serves so that the floor or another base does not spoil, on which you are going to cut off the foam rubber, well, and as you understood for protecting the tip of the knife. Well, the last point how to cut off foam, this is the process of cutting. To do this, take a very sharp knife. Your kitchen knife is clearly not suitable here, since his blade is thicker. Therefore, I advise you to use a stationery knife, or a construction knife, like those that cut linoleum. It is very important that the blade and the tip are sharp, otherwise you can’t get a foam rubber. Well, then go to work, spend exactly along the line with a knife, preferably without using the stop, since the emphasis will be pressed on foam, thereby creating a load in it, and the knife will be poorly cut. If you doubt your abilities, then it is better to practice a little on another piece of foam rubber so as not to spoil the workpiece. Anyway, foam rubber is usually cut in order to sheathe up her upholstered furniture. Therefore, you can not do perfectly evenly, and you can’t get 100% exactly cut off exactly. The fabric will still be on top of the foam, which will smooth out all the irregularities and errors of the cut.

To cut foam and make its edges extremely even, it is necessary to stock up on special tools and consumables. Among them:

leaf or roll of polyurethane foam;
lining. it will help protect the surface from scratches that occur during cutting. A plywood sheet supplemented with cardboard is suitable (a cardboard box will fit in a laid out state);
Building knife or other knife with a long blade. Additionally, buy a set of removable blades to easily change them after wear. Remember that high.quality knife is the key to the success of cutting foam. So buy models of the average price segment;
ruler, roulette;
If you need a figured cutting, you need a cardboard template with a cut pattern;
marker. with it, you can outline a fishing line for a trimmer cut.

How to cut furniture foam: instruction

If all the materials and tools are at hand, you can proceed directly to the process. Compliance with cutting technology will achieve an ideal result. How easy it is to cut foam. complete instruction:

Put the plywood, wood-fiber plate on a flat surface (for example, floor), and place a sheet of cardboard on top of it on top of it.
Lay the foam plaster on top of the cardboard so that the place of the future section is on the cardboard and does not go beyond its edges.
Using the ruler, draw a fishing line for a trimmer along which you need to make a cut. Cutting can be made under a ruler if the length of the knife blade allows.
Having taken the knife, configure the required length of the blade. Then make a small incision on one side. After insert the knife into the starting fishing line for the trimmer of the cut and make confident accurate movement. The second hand at this moment slightly grab the edges of the foam block. Cutting foam at an angle is the best solution that allows you to make a cut as even as possible.

A sharp knife: stationery or for cutting linoleum;
marker or felt.tip pen;
thick cardboard, plywood or a piece of board under the base;
wooden rail or ordinary ruler, pattern (for curved cuts).
Select a place for laying out a sheet of foam and put a thick cardboard or a piece of board under the material so that when cutting, do not spoil the base (floor, countertop);
Make a pitch or marker with a felt.tip pen or marker and connect them using a rail or ruler. For a cut under the radius, use a template or pattern;
Take the knife and, holding it strictly vertically, with a strong, confident movement, spend on marking. Do not use the ruler when cutting, since it will put pressure on the foam rubber under the weight of the hand, crush it, and the cut will eventually turn out to be uneven;
If the foam rubber does not cut through to the end, spread your fingers with the “processed” site and bring the work to the end to the end. When the bullying appears, break the blade of the clerical knife or replace it.

Lubricate the edges of the prepared parts with glue using a roller, brush or spray gun. Economy option. a gun, the consumption of the composition is about 70 grams./cm.sq.;
Wash the time specified in the instructions;
Connect the details, pressing tightly or pressing the press, until a reliable, even, elastic seam is formed.

Vinyl Text company: Furniture foam for the sofa and other upholstered furniture, as well as upholstery materials, accessories to retail, wholesale and delivery to all regions Title = “Sources:”]https: // WeldingMaterials.ru/rezka/kak.rezat-sorolon.HTML
https: // 101benzopila.ru/kak.rezat-sorolon-v-domasnih-osloviah/
https: // 101benzopila.ru/kak.rezat-sorolon-v-domasnih-osloviah/
https: // Veloelektro.ru/kak.rezat-sorolon-v-domashnih-osloviyah.HTML
https: // Stroi-obzor.ru/strojka/kak.rezat-sorolon-figurno/
https: // Stroi-obzor.ru/Strojka/Kak-Rovno-Trezat-Tolstyj-Porolon/
https: // pilomaterialy-spb.ru/rezka/rezka-sorolona-v-domashnih-osloviyah.HTML
https: // Remontask.ru/chem.rezat-rovno-Tolstij-sorolon
https: // Remontask.ru/chem.rezat-rovno-Tolstij-sorolon [/spoiler]